Asa 5505 problems
pbm with asa5505.For 45 min-1h &later on internet is down.any solution
hostname DarrkoEOOD
domain-name default.domain.invalid
enable password my encrypted
names
interface Vlan1
nameif inside
security-level 50
ip address 89.x.x.65 255.255.255.192
interface Vlan2
nameif Evrokom
security-level 90
ip address 89.x.x.66 255.255.255.252
interface Vlan3
description Evrocom-DNS_Blackhole
nameif DNS
security-level 0
ip address 10.0.0.1 255.255.255.252
interface Ethernet0/0
description LAN
interface Ethernet0/1
description Evrokom
switchport access vlan 2
interface Ethernet0/2
description Evrocom-DNS_Blackhole
switchport access vlan 3
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
passwd my encrypted
ftp mode passive
clock timezone EEDT 2
clock summer-time EEDT recurring last Sun Mar 3:00 last Sun Oct 3:00
dns server-group DefaultDNS
domain-name default.domain.invalid
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
access-list IPSAllowedOutsideInterface extended permit ip host 71.169.2.10 any
access-list IPSAllowedOutsideInterface extended permit ip host 72.89.63.208 any
access-list IPSAllowedOutsideInterface extended permit ip 69.64.222.0 255.255.255.0 any
access-list IPSAllowedOutsideInterface extended permit ip host 77.85.217.18 any
access-list IPSAllowedOutsideInterface extended permit ip host 62.204.140.9 any
access-list IPSAllowedOutsideInterface extended permit tcp 213.226.0.0 255.255.0.0 any eq ssh
access-list IPSAllowedOutsideInterface extended deny tcp any any eq 3389
access-list IPSAllowedOutsideInterface extended deny tcp any any eq ssh
access-list IPSAllowedOutsideInterface extended permit ip any any
pager lines 24
logging timestamp
logging buffer-size 1048576
logging buffered debugging
logging asdm informational
mtu inside 1500
mtu Evrokom 1500
mtu DNS 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any Evrokom
asdm image disk0:/asdm-522.bin
no asdm history enable
arp timeout 14400
global (Evrokom) 10 interface
nat (inside) 10 89.215.168.64 255.255.255.192
access-group IPSAllowedOutsideInterface in interface inside
access-group IPSAllowedOutsideInterface out interface inside
access-group IPSAllowedOutsideInterface in interface Evrokom
access-group IPSAllowedOutsideInterface out interface Evrokom
route Evrokom 0.0.0.0 0.0.0.0 89.215.174.65 1 track 1
route Evrokom 217.9.224.2 255.255.255.255 89.215.174.65 1 track 2
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:20:00 udp 1:00:00 icmp 0:00:05
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
username admin password rj3RJA7.tmoyw8bB encrypted privilege 15
username thegrave password my encrypted privilege 15
aaa authentication ssh console LOCAL
http server enable
http 62.x.x.9 255.255.255.255 Evrokom
http 213.x.x.0 255.255.255.0 Evrokom
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
service resetinbound interface inside
track 1 rtr 1 reachability
track 2 rtr 2 reachability
telnet timeout 5
ssh 72.x.x.208 255.255.255.255 Evrokom
ssh 213.x.x.0 255.255.0.0 Evrokom
ssh 67.x.x.39 255.255.255.255 Evrokom
ssh 62.x.x.9 255.255.255.255 Evrokom
ssh 77.x.x.18 255.255.255.255 Evrokom
ssh timeout 5
ssh version 2
console timeout 0
dhcpd lease 32000
dhcpd address 89.x.x.66-89.215.168.125 inside
dhcpd dns 217.x.x.2 212.39.90.42 interface inside
dhcpd enable inside
ntp server 129.6.15.29 source Evrokom
ntp server 129.6.15.28 source Evrokom prefer
prompt hostname context
Cryptochecksum:xxx
: end
Use this Cisco ASA 5500 Series Adaptive Security Appliances Troubleshoot and Alerts
http://www.cisco.com/en/US/products/ps6120/tsd_products_support_troubleshoot_and_alerts.html
Similar Messages
-
Cisco ASA 5505 - problem with negotiating IP address from PPPoE
Hi all,
I have problem with negotiating IP address from PPPoE. There is following design: ISP providing vDSL ending on VDSL modem in bridge mode. Behind brigde modem is ASA 5505 terminting PPPoE on OUTSIDE. Everything works fine except negotiating IP address from PPPoE server.
I have configured ASA 5505 with (ASA Version 9.2(2)4) for PPPoE like this [1.]. But If i try to "show" IP address on OUTSIDE interface a get this [2.], ok strange but let's continue. If list "show vpdn pppinterface id 1" i get this [3.]. Seems that I got public IP addres what was right, but this IP address was not associated with interface OUTSIDE?
Well, if I set IP address manually like this [4.] and also set a default route everything works fine but what will happen when ISP change reservation for my IP address or default gateway.
I have tried different version of ASA OS like 8.4, 9.1 but without luck.
Can anybody help me. Thanks a lot.
Regards
Karel
[1.]
interface Vlan100
description >>VLAN pro pripojeni do internetu<<
nameif OUTSIDE
security-level 0
pppoe client vpdn group O2
ip address pppoe setroute
vpdn group O2 request dialout pppoe
vpdn group O2 localname O2
vpdn group O2 ppp authentication chap
vpdn username O2 password *****
interface Ethernet0/0
description >>uplink O2 vDSL<<
switchport access vlan 100
[2.]
ciscoasa(config-if)# show ip address vlan 100 pppoe
ciscoasa(config-if)# 0.0.0.0 255.255.255.255 on Interface: OUTSIDE
ciscoasa(config-if)# show interface vlan 100 detail
Interface Vlan2 "OUTSIDE", is up, line protocol is up
Hardware is EtherSVI, BW 100 Mbps, DLY 100 usec
Description: >>VLAN pro pripojeni do internetu<<
MAC address f44e.05d0.6c17, MTU 1492
IP address unassigned
Traffic Statistics for "OUTSIDE":
28 packets input, 1307 bytes
31 packets output, 721 bytes
0 packets dropped
1 minute input rate 0 pkts/sec, 3 bytes/sec
1 minute output rate 0 pkts/sec, 1 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Control Point Interface States:
Interface number is 15
Interface config status is active
Interface state is active
[3.]
ciscoasa(config-if)# show vpdn pppinterface id 1
PPP virtual interface id = 1
PPP authentication protocol is CHAP
Server ip address is 88.103.200.41
Our ip address is 85.71.188.158
Transmitted Pkts: 20, Received Pkts: 16, Error Pkts: 0
MPPE key strength is None
MPPE_Encrypt_Pkts: 0, MPPE_Encrypt_Bytes: 0
MPPE_Decrypt_Pkts: 0, MPPE_Decrypt_Bytes: 0
Rcvd_Out_Of_Seq_MPPE_Pkts: 0
ciscoasa(config-if)# show vpdn session state
%No active L2TP tunnels
%No active PPTP tunnels
PPPoE Session Information (Total tunnels=1 sessions=1)
SessID TunID Intf State Last Chg
22298 2 OUTSIDE SESSION_UP 561 secs
[4.]
interface Vlan100
description >>VLAN pro pripojeni do internetu<<
nameif OUTSIDE
security-level 0
pppoe client vpdn group O2
ip address 85.71.188.158 255.255.255.255 pppoe setroute
route OUTSIDE 0.0.0.0 0.0.0.0 88.103.200.41 1You're right that the ACL should not affect otherwise allowed communications to the interface address.
Try disabling the ip audit feature on your outside interface.
no ip audit interface OUTSIDE AP_OUTSIDE_INFO
no ip audit interface OUTSIDE AP_OUTSIDE_ATTACK -
Dear All,
I have a problem with the configuration of the ACL of my ASA 5505 router.
However, the syntax seems okay
access-list 121 extended deny icmp 192.168.0.0 255.255.255.0 any
Thanks for your helpHi,
Its hard to say when I cant see your whole configuration.
Have you attached the ACL to an interface on the ASA?
access-group 102 in interface
Only then the ACL will have some effect on the traffic. Though remember to allow other traffic in the SAME ACL. Otherwise you will block all traffic from behind the interface to which you attach this ACL.
However this ACL wont block ICMP between the hosts on the same network naturally.
- Jouni -
ASA 5505 Problem with outbound PPTP-connection on non-native vlan
Hi, why am I not being able to make a PPTP connection on vlan80 (trunked to AP Cisco 1142N) compared to vlan10? And yes, I've configured the "
inspect pptp"
ASA 5505 with sec plus licenseHi mate,
I don't know how to solve your problem but I strongly reccommend you to remove your password from the first post and to update it on your ASA device -
Cisco ASA 5505 - problems getting support
My employer has an ASA 5505 device that has been here longer than any body working here. I've tried to get my hands on some updated software or support but to little avail. I've contacted Cisco support online and they keep telling me to contact my Cisco service sales representative. Now that would be fine if anybody could remember who they are. I suspect they are not even in business anymore.
Not particularly helpful at the end of the day.
I am very close to throwing in the towel with this Cisco. All I want to do is upgrade the firmware to address some known issues we are experiencing with our current firmware.
Any other avenues I am missing?Hi Ferdinand. I don't know what a Smartnet contract is. How do I know if we have one? This ASA basically hasn't been touched for 5 years. Almost the entire staff has rotated through this company since then and nobody knowns anything. I found the invoice for it this morning after accounts searched for it, but it appears to have been purchased from a non services retailer. I contacted them and while they confirm they sold it to us they know nothing about it. They don't offer service.
What are my options? -
AT&T DSL & Cisco ASA 5505 Problems
Okay I have been working with a 5505 for two days and finally got it configured and working on an AT&T DSL Modem then when I took the 5505 to the clients office and connected/configured it to their AT&T DSL with their IPs the whole thing quite working. I noticed walk through the Tech discussions that there are lots of problems with AT&T DSL deployments and I also discovered that one working configuration was attached to a DSL in AT&Ts standard deployment as a DHCP router using dynamic IPs while the second is in bridge mode using static IPs.
So here's the question why won't the DSL Modem in bridge mode not work as a typical Internet connection like a Cable Modem? I have a Cisco Wireless VPN 4400 to it in bridge mode using static IPs and it works great and on the 4400 there are no special PPPoe settings that have to be set just standard IPs, DNSs, Gateways, Masks...
I see in the Cisco Tech Notes that it is recommended/mandatory to configure Vpdn groups and the Vlan2 to take into account the PPPoe configuration of the AT&T DSL Modem but if the DSL modem is already set in bridge mode and is handling the PPPoe authentication why does the 5505 have do it again this see,s redundant. Will try to use the example configuration additions above and post here with the results.
BTW the configuration with the DSL set as DHCP Router works without any special PPPoe configs.
Very puzzling this DSL configuration conundrum... Last point for businesses if you can use Cable or nonDSL ISP you should do so this AT&T stuff is for the birds... Angry Birds...
Thanks for the assistance in advance!!!
If static ip address:
vpdn group INTERNET request dialout pppoe
vpdn group INTERNET ppp authentication {chap|mschap|pap}
vpdn group INTERNET localname setroute
pppoe client vpdn group INTERNET
mtu outside 1492
Sent from Cisco Technical Support iPad AppHi Ferdinand. I don't know what a Smartnet contract is. How do I know if we have one? This ASA basically hasn't been touched for 5 years. Almost the entire staff has rotated through this company since then and nobody knowns anything. I found the invoice for it this morning after accounts searched for it, but it appears to have been purchased from a non services retailer. I contacted them and while they confirm they sold it to us they know nothing about it. They don't offer service.
What are my options? -
Cisco ASA 5505 - problem with ssh, icmp on OUTSIDE interface
Hi all,
I have a very strange problem with OUTSIDE interface and remote ssh. Well, I have followed documentation and configure remote access for ssh like this [1.]. If I want to connect from internet to OUTSIDE interface [2.] get no response and in log I can see this message [3.]. I really do not understand why is ssh connection dropped by OUTSIDE access-list [4.]? If I understand documentation correctly there is no impact for remote mangement/access like icmp, ssh, http(s) by interface access-list. So, why?
When I try ssh connection form internal network to INSIDE interface everything works fine and I can log in to ASA. If I try allow ssh in OUTSIDE access-list still no success and a get this message [5.]? It is strange, isn't?
The same problem with icmp if I want to "ping" OUTSIDE interface from internet a get thish message in log [6.] and configuration for ICMP like this [7.].
Full ASA config is in attachment.
Can anybody help how to fix it and explain what is exactly wrong.Thanks.
Regards,
Karel
[1.]
ssh stricthostkeycheck
ssh 10.0.0.0 255.255.255.0 INSIDE
ssh 0.0.0.0 0.0.0.0 OUTSIDE
ssh timeout 60
ssh version 2
ssh key-exchange group dh-group1-sha1
ASA-FW01# show ssh
Timeout: 60 minutes
Version allowed: 2
10.0.0.0 255.255.255.0 INSIDE
0.0.0.0 0.0.0.0 OUTSIDE
[2.]
ASA-FW01# show nameif
Interface Name Security
Vlan10 INSIDE 100
Vlan20 EXT-VLAN20 0
Vlan30 EXT-WIFI-VLAN30 10
Vlan100 OUTSIDE 0
ASA-FW01# show ip
System IP Addresses:
Interface Name IP address Subnet mask Method
Vlan10 INSIDE 10.0.0.1 255.255.255.0 CONFIG
Vlan20 EXT-VLAN20 10.0.1.1 255.255.255.0 CONFIG
Vlan30 EXT-WIFI-VLAN30 10.0.2.1 255.255.255.0 CONFIG
Vlan100 OUTSIDE 85.71.188.158 255.255.255.255 CONFIG
Current IP Addresses:
Interface Name IP address Subnet mask Method
Vlan10 INSIDE 10.0.0.1 255.255.255.0 CONFIG
Vlan20 EXT-VLAN20 10.0.1.1 255.255.255.0 CONFIG
Vlan30 EXT-WIFI-VLAN30 10.0.2.1 255.255.255.0 CONFIG
Vlan100 OUTSIDE 85.71.188.158 255.255.255.255 CONFIG
ASA-FW01# show interface OUTSIDE detail
Interface Vlan100 "OUTSIDE", is up, line protocol is up
Hardware is EtherSVI, BW 100 Mbps, DLY 100 usec
Description: >>VLAN pro pripojeni do internetu<<
MAC address f44e.05d0.6c17, MTU 1480
IP address 85.71.188.158, subnet mask 255.255.255.255
Traffic Statistics for "OUTSIDE":
90008 packets input, 10328084 bytes
60609 packets output, 13240078 bytes
1213 packets dropped
1 minute input rate 15 pkts/sec, 994 bytes/sec
[3.]
Jan 13 2015 06:45:30 ASA-FW01 : %ASA-6-106100: access-list OUTSIDE denied tcp OUTSIDE/193.86.236.70(46085) -> OUTSIDE/85.71.188.158(22) hit-cnt 1 first hit [0xb74026ad, 0x0]
[4.]
access-list OUTSIDE remark =======================================================================================
access-list OUTSIDE extended permit icmp any any echo-reply
access-list OUTSIDE extended deny ip any any log
access-group OUTSIDE in interface OUTSIDE
[5.]
Jan 12 2015 23:00:46 ASA-FW01 : %ASA-2-106016: Deny IP spoof from (193.86.236.70) to 85.71.188.158 on interface OUTSIDE
[6.]
Jan 13 2015 06:51:16 ASA-FW01 : %ASA-4-400014: IDS:2004 ICMP echo request from 193.86.236.70 to 85.71.188.158 on interface OUTSIDE
[7.]
icmp unreachable rate-limit 1 burst-size 1
icmp permit 10.0.0.0 255.0.0.0 INSIDE
icmp permit 10.0.0.0 255.0.0.0 EXT-WIFI-VLAN30
icmp permit any OUTSIDEYou're right that the ACL should not affect otherwise allowed communications to the interface address.
Try disabling the ip audit feature on your outside interface.
no ip audit interface OUTSIDE AP_OUTSIDE_INFO
no ip audit interface OUTSIDE AP_OUTSIDE_ATTACK -
Good morning,
I'm having the following problem. I configured a ASA 5505 with VPN and a VPN Remote Access Site-to-site. Everything is working, but when I reload the ASA does not work anymore VPNs, Remote Access error 412 and the Site-to-site does not connect more to solve, I have to reset and reconfigure the ASA. This is happening dopo updating the ASA, I have version 842-k8 and asdm645-106.
Does anyone have any idea what can be?
Thank you.
Running-config:
: Saved
: Written by master at 10:34:14.839 BRDT Mon Oct 10 2011
ASA Version 8.4(2)
hostname ciscoasa
domain-name default.domain.invalid
enable password 2KFQnbNIdI.2KYOU encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 0
ip address 172.16.0.140 255.255.252.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group gvt
ip address pppoe setroute
boot system disk0:/asa842-k8.bin
ftp mode passive
clock timezone BRST -3
clock summer-time BRDT recurring 2 Sun Oct 0:00 3 Sun Feb 0:00
dns server-group DefaultDNS
domain-name default.domain.invalid
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network NETWORK_OBJ_172.16.0.0_22
subnet 172.16.0.0 255.255.252.0
object network NETWORK_OBJ_172.16.0.128_26
subnet 172.16.0.128 255.255.255.192
object network NETWORK_OBJ_20.0.0.0_24
subnet 20.0.0.0 255.255.255.0
object network NETWORK_OBJ_172.16.11.0_24
subnet 172.16.11.0 255.255.255.0
object-group network obj_any
access-list 1 standard permit 172.16.0.0 255.255.252.0
access-list 1 standard permit 20.0.0.0 255.255.255.0
access-list outside_cryptomap extended permit ip 172.16.0.0 255.255.252.0 20.0.0.0 255.255.255.0
access-list outside_cryptomap_1 extended permit ip 172.16.0.0 255.255.252.0 172.16.11.0 255.255.255.0
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool pool 172.16.0.150-172.16.0.160 mask 255.255.252.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-645-106.bin
no asdm history enable
arp timeout 14400
nat (inside,outside) source static NETWORK_OBJ_172.16.0.0_22 NETWORK_OBJ_172.16.0.0_22 destination static NETWORK_OBJ_172.16.0.128_26 NETWORK_OBJ_172.16.0.128_26 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_172.16.0.0_22 NETWORK_OBJ_172.16.0.0_22 destination static NETWORK_OBJ_20.0.0.0_24 NETWORK_OBJ_20.0.0.0_24 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_172.16.0.0_22 NETWORK_OBJ_172.16.0.0_22 destination static NETWORK_OBJ_172.16.11.0_24 NETWORK_OBJ_172.16.11.0_24 no-proxy-arp route-lookup
nat (inside,outside) after-auto source dynamic any interface
route outside 172.16.11.0 255.255.255.0 187.16.33.131 10
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 172.16.0.0 255.255.252.0 inside
no snmp-server location
no snmp-server contact
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set peer 189.11.56.237
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 2 match address outside_cryptomap_1
crypto map outside_map 2 set peer 187.16.33.131
crypto map outside_map 2 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 2 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
vpdn group gvt request dialout pppoe
vpdn group gvt localname *******@turbonetpro
vpdn group gvt ppp authentication pap
vpdn username *******@turbonetpro password *****
dhcpd auto_config outside
dhcpd address 172.16.0.144-172.16.1.143 inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy crv internal
group-policy crv attributes
dns-server value 172.16.0.253 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value 1
default-domain value crvnatural.com.br
group-policy GroupPolicy_189.11.56.237 internal
group-policy GroupPolicy_189.11.56.237 attributes
vpn-filter value 1
vpn-tunnel-protocol ikev1 ikev2
group-policy GroupPolicy_187.16.33.131 internal
group-policy GroupPolicy_187.16.33.131 attributes
vpn-filter value 1
vpn-tunnel-protocol ikev1 ikev2
username master password kWH7f2vqtjMEg2Yp encrypted
tunnel-group crv type remote-access
tunnel-group crv general-attributes
default-group-policy crv
dhcp-server 172.16.0.253
tunnel-group crv ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group 189.11.**.*** type ipsec-l2l
tunnel-group 189.11.**.*** general-attributes
default-group-policy GroupPolicy_189.11.**.***
tunnel-group 189.11.**.*** ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key ****
ikev2 local-authentication pre-shared-key *****
tunnel-group 187.16.33.*** type ipsec-l2l
tunnel-group 187.16.33.*** general-attributes
default-group-policy GroupPolicy_187.16.33.***
tunnel-group 187.16.33.*** ipsec-attributes
ikev1 pre-shared-key ******
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:50ed6f55182534a2429d065a26e9b45c
: endDavid,
In order to understand why LDAP is not working run a "debug ldap 255" and then try to login or run a AAA test.
Attach the output to find out the issue.
Please check this out as well, to make sure that you have the correct settings:
ASA 8.0: Configure LDAP Authentication for WebVPN Users
HTH.
Portu. -
Remote Access VPN Problem with ASA 5505
After about ~1 year of having the Cisco VPN Client connecting to a ASA 5505 without any problems, suddenly one day it stops working. The client is able to get a connection to the ASA and browse the local network for only about 30 seconds after connection. After that, no access is available to the network behind the ASA. I tried everything that I can think of to try and troubleshoot the problem, but at this point I am just banging my head against a wall. Does anyone know what could cause this?
Here is the running cfg of the ASA
: Saved
ASA Version 8.4(1)
hostname NCHCO
enable password xxxxxxxxxxxxxxx encrypted
passwd xxxxxxxxxxx encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address **.**.***.*** 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa841-k8.bin
ftp mode passive
object network NCHCO
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.2.64
subnet 192.168.2.64 255.255.255.224
object network obj-0.0.0.0
subnet 0.0.0.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Webserver
object network FINX
host 192.168.2.11
object service rdp
service tcp source range 1 65535 destination eq 3389
description rdp
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.2.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list inside_nat0_outbound extended permit ip 0.0.0.0 255.255.255.0 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit 192.168.2.0 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
access-list NCHCO_splitTunnelAcl_1 standard permit 192.168.2.0 255.255.255.0
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list outside_access_in extended permit tcp any object FINX eq 3389
access-list outside_access_in_1 extended permit object rdp any object FINX
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-649.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static NCHCO NCHCO destination static obj-192.168.1.0 obj-192.168.1.0
nat (inside,any) source static any any destination static obj-192.168.2.64 obj-192.168.2.64
nat (inside,any) source static obj-0.0.0.0 obj-0.0.0.0 destination static obj-192.168.2.64 obj-192.168.2.64
object network obj_any
nat (inside,outside) dynamic interface
object network FINX
nat (inside,outside) static interface service tcp 3389 3389
access-group outside_access_in_1 in interface outside
route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http **.**.***.*** 255.255.255.255 outside
http **.**.***.*** 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
http 96.11.251.186 255.255.255.255 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set l2tp-transform mode transport
crypto ipsec ikev1 transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set ikev1 transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set ikev1 transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 20 set reverse-route
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto ikev1 policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client ssl-clientless
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Pool
group-policy NCHCO internal
group-policy NCHCO attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value NCHCO_splitTunnelAcl_1
default-domain value NCHCO.local
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password dhn.JzttvRmMbHsP encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group NCHCO type remote-access
tunnel-group NCHCO general-attributes
address-pool VPN_Pool
default-group-policy NCHCO
tunnel-group NCHCO ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:a2110206e1af06974c858fb40c6de2fc
: end
asdm image disk0:/asdm-649.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
And here is the logs from the Cisco VPN Client when it browses, then fails to browse the network behind the ASA:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.1.7601 Service Pack 1
Config file directory: C:\Program Files (x86)\Cisco Systems\VPN Client\
1 09:44:55.677 10/01/13 Sev=Info/6 CERT/0x63600026
Attempting to find a Certificate using Serial Hash.
2 09:44:55.677 10/01/13 Sev=Info/6 CERT/0x63600027
Found a Certificate using Serial Hash.
3 09:44:55.693 10/01/13 Sev=Info/6 GUI/0x63B00011
Reloaded the Certificates in all Certificate Stores successfully.
4 09:45:02.802 10/01/13 Sev=Info/4 CM/0x63100002
Begin connection process
5 09:45:02.802 10/01/13 Sev=Info/4 CM/0x63100004
Establish secure connection
6 09:45:02.802 10/01/13 Sev=Info/4 CM/0x63100024
Attempt connection with server "**.**.***.***"
7 09:45:02.802 10/01/13 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with **.**.***.***.
8 09:45:02.818 10/01/13 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
9 09:45:02.865 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to **.**.***.***
10 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
11 09:45:02.896 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, KE, NON, ID, HASH, VID(Unity), VID(Xauth), VID(dpd), VID(Nat-T), NAT-D, NAT-D, VID(Frag), VID(?)) from **.**.***.***
12 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
13 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
14 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports DPD
15 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
16 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports IKE fragmentation payloads
17 09:45:02.927 10/01/13 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
18 09:45:02.927 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to **.**.***.***
19 09:45:02.927 10/01/13 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0xDD3B, Remote Port = 0x01F4
20 09:45:02.927 10/01/13 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end is NOT behind a NAT device
21 09:45:02.927 10/01/13 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
22 09:45:02.943 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
23 09:45:02.943 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
24 09:45:02.943 10/01/13 Sev=Info/4 CM/0x63100015
Launch xAuth application
25 09:45:03.037 10/01/13 Sev=Info/6 GUI/0x63B00012
Authentication request attributes is 6h.
26 09:45:03.037 10/01/13 Sev=Info/4 CM/0x63100017
xAuth application returned
27 09:45:03.037 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
28 09:45:03.037 10/01/13 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
29 09:45:03.037 10/01/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
30 09:45:03.083 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
31 09:45:03.083 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
32 09:45:03.083 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
33 09:45:03.083 10/01/13 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 1 User Authenticated IKE SA in the system
34 09:45:03.083 10/01/13 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
35 09:45:03.083 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
36 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
37 09:45:03.146 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
38 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 192.168.2.70
39 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK: , value = 255.255.255.0
40 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 192.168.2.1
41 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(2): , value = 8.8.8.8
42 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD: , value = 0x00000001
43 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
44 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000F
SPLIT_NET #1
subnet = 192.168.2.0
mask = 255.255.255.0
protocol = 0
src port = 0
dest port=0
45 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = NCHCO.local
46 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_UDP_NAT_PORT, value = 0x00002710
47 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
48 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc ASA5505 Version 8.4(1) built by builders on Mon 31-Jan-11 02:11
49 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT: , value = 0x00000001
50 09:45:03.146 10/01/13 Sev=Info/4 CM/0x63100019
Mode Config data received
51 09:45:03.146 10/01/13 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 192.168.2.70, GW IP = **.**.***.***, Remote IP = 0.0.0.0
52 09:45:03.146 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to **.**.***.***
53 09:45:03.177 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
54 09:45:03.177 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from **.**.***.***
55 09:45:03.177 10/01/13 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
56 09:45:03.177 10/01/13 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 1 seconds, setting expiry to 86399 seconds from now
57 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
58 09:45:03.193 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK QM *(HASH, SA, NON, ID, ID, NOTIFY:STATUS_RESP_LIFETIME) from **.**.***.***
59 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 28800 seconds
60 09:45:03.193 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH) to **.**.***.***
61 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000059
Loading IPsec SA (MsgID=967A3C93 OUTBOUND SPI = 0xAAAF4C1C INBOUND SPI = 0x3EBEBFC5)
62 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000025
Loaded OUTBOUND ESP SPI: 0xAAAF4C1C
63 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000026
Loaded INBOUND ESP SPI: 0x3EBEBFC5
64 09:45:03.193 10/01/13 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
65 09:45:03.521 10/01/13 Sev=Info/6 CVPND/0x63400001
Launch VAInst64 to control IPSec Virtual Adapter
66 09:45:03.896 10/01/13 Sev=Info/4 CM/0x63100034
The Virtual Adapter was enabled:
IP=192.168.2.70/255.255.255.0
DNS=192.168.2.1,8.8.8.8
WINS=0.0.0.0,0.0.0.0
Domain=NCHCO.local
Split DNS Names=
67 09:45:03.912 10/01/13 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 0.0.0.0 0.0.0.0 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 0.0.0.0 0.0.0.0 261
68 09:45:07.912 10/01/13 Sev=Info/4 CM/0x63100038
Successfully saved route changes to file.
69 09:45:07.912 10/01/13 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
**.**.***.*** 255.255.255.255 96.11.251.1 96.11.251.149 100
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.2.0 255.255.255.0 192.168.2.70 192.168.2.70 261
192.168.2.0 255.255.255.0 192.168.2.1 192.168.2.70 100
192.168.2.70 255.255.255.255 192.168.2.70 192.168.2.70 261
192.168.2.255 255.255.255.255 192.168.2.70 192.168.2.70 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 192.168.2.70 192.168.2.70 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 192.168.2.70 192.168.2.70 261
70 09:45:07.912 10/01/13 Sev=Info/6 CM/0x63100036
The routing table was updated for the Virtual Adapter
71 09:45:07.912 10/01/13 Sev=Info/4 CM/0x6310001A
One secure connection established
72 09:45:07.943 10/01/13 Sev=Info/4 CM/0x6310003B
Address watch added for 96.11.251.149. Current hostname: psaserver, Current address(es): 192.168.2.70, 96.11.251.149, 192.168.1.3.
73 09:45:07.943 10/01/13 Sev=Info/4 CM/0x6310003B
Address watch added for 192.168.2.70. Current hostname: psaserver, Current address(es): 192.168.2.70, 96.11.251.149, 192.168.1.3.
74 09:45:07.943 10/01/13 Sev=Info/5 CM/0x63100001
Did not find the Smartcard to watch for removal
75 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
76 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
77 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0x1c4cafaa into key list
78 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
79 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0xc5bfbe3e into key list
80 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x6370002F
Assigned VA private interface addr 192.168.2.70
81 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700037
Configure public interface: 96.11.251.149. SG: **.**.***.***
82 09:45:07.943 10/01/13 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 1.
83 09:45:13.459 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to **.**.***.***
84 09:45:13.459 10/01/13 Sev=Info/6 IKE/0x6300003D
Sending DPD request to **.**.***.***, our seq# = 107205276
85 09:45:13.474 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
86 09:45:13.474 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from **.**.***.***
87 09:45:13.474 10/01/13 Sev=Info/5 IKE/0x63000040
Received DPD ACK from **.**.***.***, seq# received = 107205276, seq# expected = 107205276
88 09:45:15.959 10/01/13 Sev=Info/4 IPSEC/0x63700019
Activate outbound key with SPI=0x1c4cafaa for inbound key with SPI=0xc5bfbe3e
89 09:46:00.947 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to **.**.***.***
90 09:46:00.947 10/01/13 Sev=Info/6 IKE/0x6300003D
Sending DPD request to **.**.***.***, our seq# = 107205277
91 09:46:01.529 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
92 09:46:01.529 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from **.**.***.***
93 09:46:01.529 10/01/13 Sev=Info/5 IKE/0x63000040
Received DPD ACK from **.**.***.***, seq# received = 107205277, seq# expected = 107205277
94 09:46:11.952 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to **.**.***.***
95 09:46:11.952 10/01/13 Sev=Info/6 IKE/0x6300003D
Sending DPD request to **.**.***.***, our seq# = 107205278
96 09:46:11.979 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
97 09:46:11.979 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from **.**.***.***
98 09:46:11.979 10/01/13 Sev=Info/5 IKE/0x63000040
Received DPD ACK from **.**.***.***, seq# received = 107205278, seq# expected = 107205278
Any help would be appreciated, thanks!I made the change that you requested by moving the VPN pool to the 192.168.3.0 network. Unfortunately, now traffic isn't flowing to the inside network at all. I was going to make a specific route as you suggested, but as far as I can see the routes are already being created correctly on the VPN client's end.
Here is the route print off of the computer behind the (test) client:
===========================================================================
Interface List
21...00 05 9a 3c 78 00 ......Cisco Systems VPN Adapter for 64-bit Windows
10...00 15 5d 01 02 01 ......Microsoft Hyper-V Network Adapter
15...00 15 5d 01 02 02 ......Microsoft Hyper-V Network Adapter #2
1...........................Software Loopback Interface 1
13...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter
11...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface
14...00 00 00 00 00 00 00 e0 Microsoft 6to4 Adapter
16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2
23...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3
===========================================================================
IPv4 Route Table
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
69.61.228.178 255.255.255.255 96.11.251.1 96.11.251.149 100
96.11.251.0 255.255.255.0 On-link 96.11.251.149 261
96.11.251.149 255.255.255.255 On-link 96.11.251.149 261
96.11.251.255 255.255.255.255 On-link 96.11.251.149 261
127.0.0.0 255.0.0.0 On-link 127.0.0.1 306
127.0.0.1 255.255.255.255 On-link 127.0.0.1 306
127.255.255.255 255.255.255.255 On-link 127.0.0.1 306
192.168.1.0 255.255.255.0 On-link 192.168.1.3 261
192.168.1.3 255.255.255.255 On-link 192.168.1.3 261
192.168.1.255 255.255.255.255 On-link 192.168.1.3 261
192.168.2.0 255.255.255.0 192.168.3.1 192.168.3.70 100
192.168.3.0 255.255.255.0 On-link 192.168.3.70 261
192.168.3.70 255.255.255.255 On-link 192.168.3.70 261
192.168.3.255 255.255.255.255 On-link 192.168.3.70 261
224.0.0.0 240.0.0.0 On-link 127.0.0.1 306
224.0.0.0 240.0.0.0 On-link 192.168.1.3 261
224.0.0.0 240.0.0.0 On-link 96.11.251.149 261
224.0.0.0 240.0.0.0 On-link 192.168.3.70 261
255.255.255.255 255.255.255.255 On-link 127.0.0.1 306
255.255.255.255 255.255.255.255 On-link 192.168.1.3 261
255.255.255.255 255.255.255.255 On-link 96.11.251.149 261
255.255.255.255 255.255.255.255 On-link 192.168.3.70 261
===========================================================================
Persistent Routes:
Network Address Netmask Gateway Address Metric
0.0.0.0 0.0.0.0 96.11.251.1 Default
===========================================================================
IPv6 Route Table
===========================================================================
Active Routes:
If Metric Network Destination Gateway
14 1020 ::/0 2002:c058:6301::c058:6301
14 1020 ::/0 2002:c058:6301::1
1 306 ::1/128 On-link
14 1005 2002::/16 On-link
14 261 2002:600b:fb95::600b:fb95/128
On-link
15 261 fe80::/64 On-link
10 261 fe80::/64 On-link
21 261 fe80::/64 On-link
10 261 fe80::64ae:bae7:3dc0:c8c4/128
On-link
21 261 fe80::e9f7:e24:3147:bd/128
On-link
15 261 fe80::f116:2dfd:1771:125a/128
On-link
1 306 ff00::/8 On-link
15 261 ff00::/8 On-link
10 261 ff00::/8 On-link
21 261 ff00::/8 On-link
===========================================================================
Persistent Routes:
None
And here is the updated running config in case you need it:
: Saved
ASA Version 8.4(1)
hostname NCHCO
enable password hTjwXz/V8EuTw9p9 encrypted
passwd hTjwXz/V8EuTw9p9 encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 69.61.228.178 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa841-k8.bin
ftp mode passive
object network NCHCO
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.2.64
subnet 192.168.2.64 255.255.255.224
object network obj-0.0.0.0
subnet 0.0.0.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Webserver
object network FINX
host 192.168.2.11
object service rdp
service tcp source range 1 65535 destination eq 3389
description rdp
object network obj-192.168.3.0
subnet 192.168.3.0 255.255.255.0
object network obj-192.168.2.0
subnet 192.168.2.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.2.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list inside_nat0_outbound extended permit ip 0.0.0.0 255.255.255.0 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit 192.168.2.0 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
access-list NCHCO_splitTunnelAcl_1 standard permit 192.168.2.0 255.255.255.0
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list outside_access_in extended permit tcp any object FINX eq 3389
access-list outside_access_in_1 extended permit object rdp any object FINX
access-list outside_specific_blocks extended deny ip host 121.168.66.35 any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
ip local pool VPN_Split_Pool 192.168.3.70-192.168.3.80 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-649.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static NCHCO NCHCO destination static obj-192.168.1.0 obj-192.168.1.0
nat (inside,any) source static any any destination static obj-192.168.2.64 obj-192.168.2.64
nat (inside,any) source static obj-0.0.0.0 obj-0.0.0.0 destination static obj-192.168.2.64 obj-192.168.2.64
object network obj_any
nat (inside,outside) dynamic interface
object network FINX
nat (inside,outside) static interface service tcp 3389 3389
access-group outside_access_in_1 in interface outside
route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http 69.61.228.178 255.255.255.255 outside
http 74.218.158.238 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
http 96.11.251.186 255.255.255.255 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set l2tp-transform mode transport
crypto ipsec ikev1 transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set ikev1 transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set ikev1 transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 20 set reverse-route
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto ikev1 policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh 96.11.251.186 255.255.255.255 outside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client ssl-clientless
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Split_Pool
group-policy NCHCO internal
group-policy NCHCO attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value NCHCO_splitTunnelAcl_1
default-domain value NCHCO.local
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password dhn.JzttvRmMbHsP encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Split_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group NCHCO type remote-access
tunnel-group NCHCO general-attributes
address-pool VPN_Split_Pool
default-group-policy NCHCO
tunnel-group NCHCO ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:9e8466cd318c0bd35bc660fa65ba7a03
: end
asdm image disk0:/asdm-649.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
Thanks again for your help,
Matthew -
VLAN problems with SG200-8P and Cisco ASA 5505 (Sec Plus license)
Hi, I've been pulling my hair out trying to get simple vlan trunking working between these devices.
Basically, no clients on VLAN 99 (guest) will receive DHCP ip addresses when plugged into the SG200. I have the SG200<>ASA VLAN trunk configured correctly, as I know it, and I've tried numerous variations (set trunk as general tag/untagged, etc., set the ap port to general tag/untag, etc). Both AP's work properly when connected to the ASA e0/3 port but either will only pull the "inside" VLAN dhcp address when connected to the SG200 switch
VLAN 1 - inside (has separate dhcp scope assigned by ASA)
VLAN 99 - guest (has separate dhcp scope assigned by ASA)
SG200
purpose
ASA 5505 (Sec Plus license)
purpose
g2
Trunk 1UP,99T
Ubiquiti AP (VLAN 1 works, VLAN 99 does not
g3
Access port 99T
vlan 99 does not work
g8
Trunk 1UP, 99T
< Trunk between switch and ASA >
Int e0/2
switchport trunk allowed vlan 1,99
switchport trunk native vlan 1
switchport mode trunk
Int e0/3
switchport trunk allowed vlan 1,99
switchport trunk native vlan 1
switchport mode trunk
Second ubiquiti AP
Both VLAN 1 and VLAN 99 clients work properlyFrustrated - yes. Confused - maybe not as much, but I could have put some more effort into the overall picture.
There are two VLANs (1 - native) and (99 - guest). There is a trunk port between the SG200 and the ASA configured as 1-untagged 99 - tagged.
No clients connected to the SG200 on VLAN 99 are able to access the ASA VLAN 99 using either a static VLAN IP address or DHCP. The problem occurs whether I configure the SG200 with an access port 99-tagged or Trunk port 1UP, 99T or general port 1U, 99UP or any combination thereof.
Anything connected to the SG200 on the native VLAN works properly.
Anything connected to the ASA VLANs (1 or 99) works properly
I have not yet tried to see what the switch is doing with the VLAN tags but I suspect I have some mismatch with the Linksys/Cisco SG200 way of setting up a VLAN and how traditional Cisco switches work.
I was hoping someone with a working SG200 - Cisco ASA setup could share their port/trunk/VLAN settings or perhaps point me in the right direction.
SG200 g2 - trunk port (1UP, 99T) -- Access Point
SG200 g2 - access port (99U)
SG200 g8 - trunk port (1UP, 99T) connected to ASA5505 e0/3
ASA5505 e0/3 (switchport trunk allowed vlan 1,99, switchport trunk native vlan 1, switchport mode trunk)
Thanks, -
Cisco ASA 5505 and DHCP Client Problems
Hi, i have a problem. I've connected my ASA appliance to an ADSL modem, and i dont get an DHCP address on the outside interface (e0/0). I use the asa-722-19.bin firmware.
I turned on the debugging for the DHCP client and could see that the ASA device was sending out broadcasts but a reply never came. Instead I connected the device to my internal network where the ASA got an address instantly.
I read somewhere that if I was to use ?ip address dhcp client-id fastethernet 0″, then I got an address from the ISP.
I tried looking for a similar command on the ASA5505 but I couldn?t find anything. I did however find a page on the Cisco site confirming my suspicions. It said some ISP?s require the client-id field of the DHCPDISCOVER request to be filled.
I've also read that this issue has beed fixed since a few weeks, now they have released version 7.2(2).22 where you can define ?dhcp-client client-id interface outside? in global configuration mode. Im running 7.2(2).19 and i cannot find any command like that in my appaiance. How do i fix my problem ? Or how do i get about recieving the 7.2(2).22 firmware update.
Regards !
LeifHi again! I thought I should share the solution that worked for me. I use software version 7.2(2) on this device. ASDM 5.2(2). In ASDM open configuration / Interfaces. Click in outside (my case 0/0) and press Edit. Then open the tab Advanced and set the correct Active Mac address. Fore some reason its empty by default and the ISP/modem don't like that. You will find the correct MAC address under the help menu / "About ASA". Im sure there is some another way to do this but this is a simple "how-to" that works with Swedens biggest ISP and their standard DSL modem.
When I used a Linksys DSL modem in bridge mode without the MAC address set I got an inside IP adress (192.168.x.x) from the modem to the ASA. After setting the MAC address I just had to do a renew and got the outside address right away. /Bjorn
(future users searchwords: no ip from isp, ASA 5505 and cable modem). -
DNS Server problems with ASA 5505
Hi guys,
we setup a new ASA 5505 which is mainly used as our VPN gateway. The ASA is configured and controlled by our ISP (and this is where the problem starts )) and they somehow cannot manage to get the VPN settings really working.
So, here is our problem.
our machines(Windows 7) are configured to get the network settings through DHCP (Windows 2012 Server).
Before I connect with AnyConnect to our VPN gateway, the DNS Server setting in the network settings for the adapters(IPv4) are set to 'dynamic'
When I now connect, this setting is changes to a statc entry (which is our DNS server).
When disconnecting, it is not reverted back, which means I have to do this always manually.
What I do not understand is the fact, that the DNS server is set for all the adapters, shouldtn't it be only set to the anyconnect adapter?.
The interesting thing is, that when I connect to a different ASA, this does not happen. The ISP is now saying, that the machines are configured exactly the same and that they cannot reproduce, but I can't believe this.
This issue shows up at every machine which connects to our vpn, so it is not only a single machine which might be misconfigured.
Do you have any idea what might cause this issue?
btw, the second ASA (which works) is from our partner company, so we cannot simply copy the config
THanks in advance
PatrickNice to see someone from BT has addressed your issue
I have this exact same problem, seems completely bizarre, I'm pretty sure I had the same problem with the original home hub (i have the latest one now). Can you confirm whether the problem does affect anyone with a bt home hub and not just the one that the dyndns is pointing at? I'll try and confirm by hitting your domain from my home connection. -
Problems with pinging ASA 5505
Hi
im having strange network issues and wonder if my ASA 5505 can be the problem.
Memory usage on my ASA is 232MB of 256MB. Running 8.4(4)1
It stops responding on the inside interface suddenly when i try to ping it. We have about 20 clients on the network.
Any ideas?Hi,
Is this issue intermittent or the pings are never working ?
If it is intermittent , you would have to check if the pings are even reaching the ASA device interface and that should be able to isolate the issue to the ASA hardware.
You can apply a simple capture on the Interface that you are testing with:-
capture cap interface <Name Of Interface> match icmp host <Interface IP> <Test PC IP>
capture asp type asp-drop all
Also , collect the show tech at that time of the issue and we should be able to verify the issue.
Is there a Layer 3 hop or another Layer 2 Switch connected between the client and the ASA device ?
Thanks and Regards,
Vibhor Amrodia -
ASA 5505 + ASA 5540 static VPN, ssh and rdp problems
Greetings!
I've recentely set up a VPN between Cisco ASA 5540(8.4) ana 5505(8.3).
Everything works fine, but there is a small problem that is really annoying me.
From the inside network behind ASA 5505 I connect via rdp or ssh to a host inside ASA 5540.
Then I minimize ssh and rdp windows and don't use it for ten minutes. But I still use VPN for downloading some files.
Then I open ssh window - the session is inactive, open rdp window - I see a black screen (for 10-15 seconds, and then it shows RDP)
There are no timeouts on ssh or rdp hosts configured, via GRE tunnel it works perfectly without any hangs.
What can I do to get rid of this problem?
Thanks in advance.Dear Fedor,
You could try adding the following commands to your configuration (on both ASAs) in order to increase the timeout values of the specific TCP sessions:
access-l rdp_ssh permit tcp 1.1.1.0 255.255.255.0 2.2.2.0 255.255.255.0 eq 22
access-l rdp_ssh permit tcp 1.1.1.0 255.255.255.0 2.2.2.0 255.255.255.0 eq 3389
class-map TCP_TIMEOUT
match access-list rdp_ssh
policy-map global_policy
class TCP_TIMEOUT
set connection timeout idle 0:30:00
set connection timeout half 0:30:00
* Please make sure you define the specific RDP and SSH ports in the ACL and avoid the use of "permit ip any any".
Let me know.
Portu.
Please rate any post you find useful. -
Problems upgrading ASA 5505 memory
I am trying to get experience with 8.4 code on my 5505. I purchased a Cisco 512MB memory upgrade and installed it. It booted up once and I thought I was ok. I then looked down and noticed that all lights were blinking on the front panel and I had no console access.
Since I dont have smartnet on my personal 5505, calling TAC for help isnt an option. That is why I spent extra money on Cisco memory but it looks that didnt help. I am assuming all blinking lights isnt a good thing but I havent been able find an explanation.
I will try reseating the memory to see if that is the problem. I put the ASA on an anti-static mat and had it and myself properly grounded.
If this doesnt fix it, I will return the Cisco memory to the vendor and go back to the original installed memory. The ASA 5505 worked fine on 8.2.5.
Would appreciate any suggestions,
RonRonald and James,
It has been over a month since you posted, so perhaps your issue was resolved. I actually experienced the exact same issue with my personal ASA 5505 today following an upgrade to 512MB. What really surprised me was James' comment that his worked for about 12 hours and stopped. That's exactly what happened to me today. It might have been 13 hours, but it was definitely in the ballpark.
The first thing I did was just disconnect power and re-connect the power to see if it magically went away. (I've never had to cycle the power on my ASA before, so I was not hopeful this would work. In fact, I was glad it did not work, as that would concern me even more.)
The next thing I did was disconnect everything, open the case, remove the RAM, blow out all of the dust using compressed air, and then re-install the RAM. So far, so good, but it has only been 15 minutes.
I'll keep an eye on this, obviously, but I am nonetheless curious to hear more about your situations. Were you able to resolve the problem permanently or were you unable to make the upgrade to 512MB?
UPDATE - My ASA continued to have issues with the new RAM module. It turned out to be a defective SIMM. I contacted the seller and returned the defective SIMM. They sent a new one and it works just fine.
Maybe you are looking for
-
Ferramenta para auxiliar no customizing da CBT (MM e SD) / Imposto Retido
Olá, Criei uma ferramenta para auxiliar no customizing da CBT que é entregue pela Nota 1706309. A motivação para a criação dessa ferramenta se deu por conta do customizing nesse caso ser muito extenso. Existe um PDF anexo à nota o qual é bem explicad
-
How to find out the support package level applied in BusinessObjects
Hello experts, I recently installed SBOP 4.0 BI on mi linux server. Can somebody tell me how to know what is the latest SP (support package or Service package??) installed on my Server. I know the current SP available is SBOP BI Platform Servers 4.0
-
[SOLVED] Firefox 2.0.0.8 Font Issues
Update: Updating to Firefox 2.0.0.8-2 fixes this problem. I upgraded from Firefox 2.0.0.7 to 2.0.0.8 and am now experiencing some strange font problems. The font spacing is completely messed up in 2.0.0.8. Anyone else experiencing this? Here's how it
-
hi I need to pan an image horizontally to left instead of to right , is this possible ?
-
IMac (intel) Mountain Lion screen blank
My iMac screen has blanked (black). Currently showing "Loading Photos..." which happens when it goes into screen saver mode. I have tried pulling the plug and restarting to no avail. My previous iMac G5 failed in a very similar way and had to be repl