Banded profile after line trouble after 3 days

Hi, I had some line trouble over a week ago and needed a BT engineer to come and fix the dead line. This was duly sorted and I found when I connected for the first time after this my down speed was 288Kbps and up was 1024Kbps which I understand is a banded profile because of the connection trouble. I waited for over 3 days and there was no improvement so I disconnected and tried again and my down speed went up to 576 Kbps. Now I have waited another 3 1/2 days and its still the same, I dont want to disconnect again as this could mess up getting this banding removed, do I have to do anyhting else to get my connection back to normal or just wait?
Thanks in advance

Hi it can take up to 5 days continuous connection for the banding to lift can you please post your hubstats and the full diagnostic bt speed test but do not restart the hub as the instructions ask
http://forumhelp.dyndns.info/speed/adslstats.html
http://forumhelp.dyndns.info/speed/speedtester.html
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Similar Messages

3072kbps Banded profile not lifting after 5 days.

As the title sais, I'm stuck on a banded profile and it doesn't seem to be wanting to budge.
I've been in sync now for 137 hours with no drops or disconnects.
My speeds are usually up in the 3800-4200kbps range and I've never had a problem with line stability or disonnections that could have caused it prior to the banding taking place.
My only guess is family members unplugging the router overnight when it's not being used, which I've stated over and over again too them that they shouldn't unplug it. but no one seems to listen
Not sure how the process goes on the forums nowadays but If there is a mod I can contact who's willing to unband my line manually (If possible) then I'd be extremely grateful, thanks.
If you felt my post was informative and helpful then please click the star below my name/avatar.
Cheers!

Hi Welcome to the community forums
Here is a basic guide to getting help from the community members done by CL Keith Please read through the link posted http://forumhelp.dyndns.info/speed/first_steps.html
once you have posted the information asked for then the community members can help you more
if using a hub 4 locate these lines located in the hub logs
Lines should look like this
19:11:29, 07 Nov. (2290101.460000) DSL noise margin: 7.00 dB upstream, 6.10 dB downstream
19:11:29, 07 Nov. (2290101.390000) DSL line rate: 448 Kbps upstream, 288 Kbps downstream
Thank You
This is a customer to customer self help forum the only BT presence here are the forum moderators
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Banded Profile after BT repair

I've been doing a lot of reading over the last few days and believe I have a Banded Profile. I suspect the answer to my question is going to be "Wait until you have had a stable connection for three days and it'll be lifted" but I have a few questions.
History:
Moved into this house mid 2010. Signed up for BT Broadband, phone and BT Vision. Broadband was about 2 Mbps download. Line was a bit crackly. Broadband often dropped when the phone rang.
BT came out and cured the noise BB was up to 3.5-4 Mbps. Bought the BT BB Accelerator Plate. Fitted and 48 hours later had 8-10 Mbps. Hub used to restart once every 2-3 months. No issues no problems.
Until 2 weeks ago.
The Problem:
One day the phone line was very noisy. The broadband constantly dropped and often would not get a connection for hours. When it did it might last 5 minutes. Long story short it was a fault in the line between the street pole and the master socket. Once replaced the line was clearer than ever and the BB was back on.
It was running at 10 Mbps for the best part of a day AFTER the line was replaced. I tested by picking up the phone and making calls inbound and outbound. Nothing caused it to drop. Until the following morning when the hub rebooted itself. Thinking this was just a part of the checks it does now the line was back I ignored it until I realised the speed is down to 3,072 Kbps.
Speaking to BT they mentioned i had a high "Noise Margin" and unable to get a decent explanation other than just wait and it'll come back, I started Googling and found this site. Much reading later (and I HOPE understanding) it appears I have a Banded Profile. I have noticed the general advise is wait until you have 3 days without an interrupted connection before asking for help. Previously I was rebooting every evening and morning on the advise of a work colleague. I got to 3 days uninterrupted earlier today. Came home at 6pm, checked the router stats and found it must have rebooted around 12pm (which should have taken it over 3 days) I checked the speed and it's 3,072 Kbps still. My upstream has increased from 1,038 to 1,138 Kbps. With that the Upstream Noise Margin has dropped from 9.7 dB to 6.3 dB, but why not my downstream Noise Margin? Downstream is still 14-16 dB.
I realise the banded profile is imposed because the constant reboots made BT think it's an unstable line - which it was DURING the fault. However i had a good 18 hours or so with 10 Mbps (with no hub reboots) after the repair only for one hub reboot to apparently cause the Banded Profile (or at least be the one that cause the Banded Profile to be invoked).
Am I correct in thinking 6 dB is best/optimum Noise Margin?
Do I have to wait another 3 days (or more) for the downstream to be adjusted separately?
I can't believe there is still a fault with the line. The line was fine all the way to the street pole but the engineer suspects the line to the house was very old and possibly had a break.
What if I can't get back the old speed I had? It's not life and death but it's infuriating to have 10 Mbps for 2 years, have something fixed and then get about a third of that...
In case it helps stats today
ADSL Settings
VPI/VCI 0/38
Type PPPoA
Modulation G.992.5 Annex A
Latency type Interleaved
Noise margin (Down/Up) 14.6 dB / 6.1 dB
Line attenuation (Down/Up) 32.9 dB / 14.8 dB
Output power (Down/Up) 17.1 dBm / 1.7 dBm
Loss of Framing (Local/Remote) 0 / 0
Loss of Signal (Local/Remote) 0 / 0
Loss of Power (Local/Remote) 0 / 0
FEC Errors (Down/Up) 537 / 0
CRC Errors (Down/Up) 0 / 0
HEC Errors (Down/Up) 0 / 0
Error Seconds (Local/Remote) 0 / 0
Thank you
Solved!
Go to Solution.

Like this?
ADSL line status
Connection Information
Line state Connected
Connection time 0 days, 09:12:37
Downstream 3,072 Kbps
Upstream 1,135 Kbps
ADSL Settings
VPI/VCI 0/38
Type PPPoA
Modulation G.992.5 Annex A
Latency type Interleaved
Noise margin (Down/Up) 14.5 dB / 6.2 dB
Line attenuation (Down/Up) 32.9 dB / 14.8 dB
Output power (Down/Up) 17.0 dBm / 1.7 dBm
Loss of Framing (Local/Remote) 0 / 0
Loss of Signal (Local/Remote) 0 / 0
Loss of Power (Local/Remote) 0 / 0
FEC Errors (Down/Up) 642 / 0
CRC Errors (Down/Up) 0 / 0
HEC Errors (Down/Up) 0 / 0
Error Seconds (Local/Remote) 0 / 0
If so it was a copy and paste error.
Not doing any more manual reboots/restarts....
BTW are those FEC errors an issue? I didn't think so, but i've already misunderstood one thing so far...

Sony Xepia give me so much trouble after 18 days

I went to the Vodacom shop @ Cape Town Waterfront on the 31st of August 2013 to get my new upgrade. Then on the 16th of September I phone that store no one answer the phone at about 19h30. The next day the 17th September I took my phone to the Green Point Vodacare shop. What amazing service. http://www.cellucity.co.za/fastaid.htm They pointed out to me that my Black Berry Service was never cancelled & so was my insurance not cancelled as well.
Been dealing with [email protected] from the Waterfront he put me on to Herman. Then two days later after about 15 emails & 5 more phone calls. Herman from Vodacom V&A phone me. He was very help full & gave me a Samsung handset that could get emails. In between this I get a call that my new Sony Xepia has to go to Johannesburg for high-end service, I only had it for 18 days.. Was so happy with my Black Berry for two years & now this Sony Xepia give me so much trouble after 18 days. I am so disappointed, in this whole experience. Wish I never gave up my Black Berry. My Job number 9205308-08262819

I don't quite understand what is it that you need help with?
"I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

Stuck at 0.25 Mbps for 16 days after line repair

Hello,
I am currently experiencing some very slow broadband speeds following repair of a line fault. I believe it is due to a banded profile, although I'm not an expert.
We had terrible noise on our telephone line. As you can imagine, our broadband was severely affected. The fault was repaired on 18th June and now the telephone line is nice and quiet.
However, the broadband has failed to recover. It's now been 16 days since the repair and I've been pulling my hair out. I was told I have to wait 10 days or more for the broadband to recover. Can anyone explain why this is necessary? Contractually am I obliged to suffer an extended period of low speed following a repair? I'm sitting here staring at a solid 32 dB SNR margin whilst paying BT for an unusuable broadband connection.
I have paid for a 3G Modem and SIM card because the BT Broadband is currently unusable. Has anyone ever had success in recovering these type of costs from BT?
Any advice appreciated. Speedtests and router stats below (Draytek Vigor 2830n).
Thanks,
Brian
Signal-Noise Ratio Margin
Loop Attenuation

i agree you are in a banded profile and need to stay connected 24/7 for 3/5 days and the banding should release and noise margin drop down to 12/15db with corresponding speed increase. You then to remain connected as noise margin drops probably in steps of 3db until it gets to normal 6db
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

10 days training period after line reset

Hi,
So on Monday morning the engineer finally turned up and did line reset which in results I was getting my full speed (47.5/9). And very low pings 16ms to bbc.co.uk, abou 6ms on 1st hop but this morning hh5b decided to restart in results my ping went up by 12ms, now 28ms to bbc.co.uk and it decreased my speed by 3mb. Can anyone explain me how 10 days of training period works? I thought the router must stay stable for more than 10 days. Is it still training my line after router drop?
I suspect interleaving turned on on my line but why after only 2 days instead of 10 training days?
I have been told by engineer that I am very far away from the cabinet around 800m and that the line is working in 100% just after line reset and it wont stay like that.
Best regards

Tonight I have noticed that I can't open any website (it takes about 3 minutes to open any website) and I am having a high packet loss on teamspeak3. The Noise Margin dropped from stable 6.0 to 4.5-5.0. It forces me to reboot my router but I don't want to, because my speed will drop and ping will go up occasionally. What can I do in that situation?
Some stats:

Troubles after installing Catalyst and re-installing KDE

Hi everybody, when I was installing arch I was following the wiki and installed the open source driver xf86-video-ati and KDE (the last version in the repository). After that everything worked fine, until I heard about some nice games that run on Linux. This is the place where the troubles began. I read that I should switch video drivers with the catalyst ones for better 3D performance. After a couple painful days I had the Catalyst working... or had I. In this painful period I uninstalled the xf86-video-ati driver, installed the Catalyst (several times), after that I had many crashes from the KDE so I decided to re-install it too :] So the result from all this is: I can play the games that I wanted, but many of the nice KDE effects disappear (ex. the window switching - whatever type of window switch I select I get the basic one) plus the synaptics drivers don't work. I also found some errors in the /var/log/kdm.log file:
X.Org X Server 1.11.4
Release Date: 2012-01-27
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.2.2-1-ARCH x86_64
Current Operating System: Linux sphex 3.3.6-1-ARCH #1 SMP PREEMPT Sun May 13 10:52:32 CEST 2012 x86_64
Kernel command line: root=/dev/sda2 ro nomodeset
Build Date: 29 January 2012 03:38:00PM
Current version of pixman: 0.24.4
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Thu May 31 21:56:50 2012
(==) Using config file: "/etc/X11/xorg.conf"
(==) Using config directory: "/etc/X11/xorg.conf.d"
(EE) module ABI major version (16) doesn't match the server's version (13)
(EE) Failed to load module "synaptics" (module requirement mismatch, 0)
(EE) No input driver matching `synaptics'
(EE) fglrx(0): Can not enable interrupt sourceID 0xff000066!
klauncher(586) kdemain: No DBUS session-bus found. Check if you have started the DBUS server.
kdeinit4: Communication error with launcher. Exiting!
kdmgreet(580)/kdecore (K*TimeZone*): KSystemTimeZones: ktimezoned initialize() D-Bus call failed: "Not connected to D-Bus server"
kdmgreet(580)/kdecore (K*TimeZone*): No time zone information obtained from ktimezoned
(EE) fglrx(0): Can not enable interrupt sourceID 0xff000066!
(EE) fglrx(0): Can not enable interrupt sourceID 0xff000066!
The XKEYBOARD keymap compiler (xkbcomp) reports:
> Warning: Compat map for group 2 redefined
> Using new definition
> Warning: Compat map for group 3 redefined
> Using new definition
> Warning: Compat map for group 4 redefined
> Using new definition
Errors from xkbcomp are not fatal to the X server
The XKEYBOARD keymap compiler (xkbcomp) reports:
> Warning: Compat map for group 2 redefined
> Using new definition
> Warning: Compat map for group 3 redefined
> Using new definition
> Warning: Compat map for group 4 redefined
> Using new definition
Errors from xkbcomp are not fatal to the X server
The XKEYBOARD keymap compiler (xkbcomp) reports:
> Warning: Compat map for group 2 redefined
> Using new definition
> Warning: Compat map for group 3 redefined
> Using new definition
> Warning: Compat map for group 4 redefined
> Using new definition
Errors from xkbcomp are not fatal to the X server
The XKEYBOARD keymap compiler (xkbcomp) reports:
> Warning: Compat map for group 2 redefined
> Using new definition
> Warning: Compat map for group 3 redefined
> Using new definition
> Warning: Compat map for group 4 redefined
> Using new definition
Errors from xkbcomp are not fatal to the X server
(EE) fglrx(0): Can not enable interrupt sourceID 0xff000066!
(EE) fglrx(0): Can not enable interrupt sourceID 0xff000066!
(EE) fglrx(0): Can not enable interrupt sourceID 0xff000066!
Same errors are seen in /var/log/Xorg.0.log. What causes them? Could this be the root problem for all others?
Here is also my /etc/X11/xorg.conf
Section "ServerLayout"
Identifier "aticonfig Layout"
Screen 0 "aticonfig-Screen[0]-0" 0 0
EndSection
Section "Module"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]-0"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]-0"
Driver "fglrx"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]-0"
Device "aticonfig-Device[0]-0"
Monitor "aticonfig-Monitor[0]-0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
EDIT:
Here is some more info on my graphics card:
01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV620 [Mobility Radeon HD 3400 Series] (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device 19e2
Flags: bus master, fast devsel, latency 0, IRQ 40
Memory at c0000000 (32-bit, prefetchable) [size=512M]
I/O ports at d800 [size=256]
Memory at fdef0000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at fdec0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: fglrx_pci
Any help would be highly appreciated.
Last edited by maistora (2012-05-31 21:34:25)

(EE) module ABI major version (16) doesn't match the server's version (13)
There's your problem. Are you using the xorg111 repo? If not, enable that and then pacman -Syuu.
As a warning, xorg-server 1.11 is now broken with the new udev package (at least until someone rebuilds it and updates the repo). You'll need to rebuild it manually to avoid this.
Last edited by Pres (2012-06-01 21:54:17)

Acrobat v9 JavaScript Alert Box - any way to add space or line break after each array item?

I have a Document level Javascript used to identify blank required fields and is triggered on document actions, Print and Save. The script identifies the blank required fields, counts them, and outputs to an Alert box indicating the number of required fields blank and lists the fields by tooltip name. The script identifies the required fields by an asterisk at the end of each tool tip.
My question is there any way to add a space or a line break after the comma for each listed item?
Here is an image of the output where the listed items are all run together.
Here is the code:
function validateFields()
//a counter for the number of empty fields
var flg = 0
// count all the form fields
var n = this.numFields
//create an array to contain the names of required fields
//if they are determined to be empty
var fArr = new Array();
//loop through all fields and check for those that are required
// all fields that have a '*' in their tool tip are required
for(var i = 0;i<n;i++){
var fn = this.getNthFieldName(i);
var f = this.getField(fn);
//tool tip is the fields\'s 'userName' property;
var tt = f.userName
//test for the '*';
if(tt.indexOf('*')!=-1 && f.value == f.defaultValue){
//increment the counter of empty fields;
flg++;
//add the fields userName (tool tip) to the list of empty field names;
fArr[fArr.length] = tt;
//now display a message if there are empty fields
if(flg>0){
app.alert('There are '+flg+' fields that require a value\n\n'+ fArr,3)
else{
this.print();

Thank you! The alert box array items now have a line break, image below. You know you have made my day and possibly several weeks as now I have more understanding about how to apply everything I have been reading in the Acrobat JavaScript guide and of course as soon as you pointed out using a "join", that triggered some old-days of working with Access and SQL queries.
I will work on the required attribute to see how I might reference it. I am laughing at myself now - good luck to me in figuring it out as I was very stick-in-the-mud regarding the line break issue.
Thanks again and here is the result of the updated code:

Sb live 5.1 trouble after installing new ATI 9550 card... help

hi there !a couple of days ago my brave asus geforce 4 ti card crashed and i installed an ati excalibur 9550 se as backup. almost everything works fine, only winamp seems to make trouble: whenever i playback some music, it has lapses with buzzing sound (sorry, not a natural speaker so i don't know any fitting words). in the past i got the same effect when i was hearing music while starting to burn an cd/dvd but now it allways happens... anyone an idea what causes this error and how to fix it
I've got an asus p4b533 board and an soundblaster li've 5. ... since i also use my pc via tv card to watch tv, and the sound of this is absolutly without any errors, i suppose that it can't just be a defect soundcard or mainboard... anybody got the same trouble after installing a new grafic card ?thanks for your help,christian

Hello. I have the exact same problem and have not been able to fix it. I have a SB Li've with an Asus P4b Motherboard. I've tried many things (playing with Codecs, updating drivers, even returning the card back to the store thinking the problem was hardware). The second card did the samething. I also tried to change the card from its PCI slots (I've tried them all) but it's still creates weird noises when playing MP3s and MPEGs, whatever the slot. Hopefully, I have a sound card integrated to the motherboard, so I use this one instead, but it's not as powerful. When using the SB card, I make sure to deactivate the motherboard's sound card in the BIOS to avoid conflicts. Could anyone help ? I've had this card for a couple of years now and have never been able to use it.
Message Edited by macaronia3 on 07--2005 0:20 AM

Server goes into constant Full GC loop after running for a day

This is a servlet application running under Resin, with Java hotspot 1.5_13 on Linux 64bit OS. JVM args are:
-verbosegc -Xms8G -Xmx8G -XX:NewSize=512m -XX:MaxNewSize=512m -XX:+TraceClassUnloading -XX:+UseParallelGC -XX:PermSize=512M -XX:MaxPermSize=512M -XX:+PrintGCTimeStamps -XX:+PrintGCDetails -XX:+DisableExplicitGC
After running for a day or so, the server goes in to constant Full GC every few seconds, essentially hanging the server. Here is an excerpt of the JVM log:
127731.579: [Full GC [PSYoungGen: 156635K->0K(352576K)] [PSOldGen: 7751937K->2260734K(7864320K)] 7908573K->2260734K(8216896K) [PSPermGen: 62855K->62855K(524288K)], 5.2972428 secs]
127737.596: [GC [PSYoungGen: 179328K->157147K(351040K)] 2440062K->2417881K(8215360K), 0.1275439 secs]
127739.066: [GC [PSYoungGen: 336475K->155824K(355136K)] 2709605K->2683786K(8219456K), 0.1729460 secs]
127740.502: [GC [PSYoungGen: 340464K->169143K(353792K)] 2980821K->2836693K(8218112K), 0.1914048 secs]
127741.562: [GC [PSYoungGen: 353783K->166305K(345344K)] 3021333K->2860977K(8209664K), 0.1367291 secs]
127742.973: [GC [PSYoungGen: 340908K->153430K(349568K)] 3147976K->3124907K(8213888K), 0.1970560 secs]
127743.946: [GC [PSYoungGen: 328278K->156065K(349568K)] 3299755K->3277928K(8213888K), 0.1868634 secs]
127745.498: [GC [PSYoungGen: 330183K->156854K(349568K)] 3564442K->3545105K(8213888K), 0.1836370 secs]
From the log it seemed that the memory usage jumped by 150M to 250M within 1.5 second, even when the user traffic was very light (a couple of page views a second, vs. 10 page views a second at peak). The same app was running fine for many hours on a Windows dev machine in load testing condition with about 300M heapsize. No memory leakage was found so far. (it would be pretty unlikely to have such a large memory leakage without being noticed in dev and testing)
Thanks for any help.
Edited by: tuxzilla on Nov 16, 2008 11:43 PM
Edited by: tuxzilla on Nov 16, 2008 11:46 PM

A NewSize of 512m seems small for an 8G heap. This would probably cause most objects to be rapidly tenured into the OldGen heap space. (Ultimately depends on your application.) You might consider either using a NewRatio in place of NewSize/MaxNewSize or not use either and instead see how the jvm handles things itself with"-XX:+UseAdaptiveSizePolicy"
VisualVM is a good graphical tool for watching gc activity.
NewRatio=1 is the largest you can go for Eden, which will set (Eden and survivor spaces) equal to oldGen space. ie, for 8G, 4g each.
Watch activity in the gc tool, you will see "sawtooth" activity. If your sawtooth pattern does not maintain a flat profile, then you have in fact have a memory leak.

Screen fields not getting displayed after Line 16

Hi All,
There is a screen exit created in IW51, now the new requirment is to add 3 more fields. I added the fields below the exiting fields, in line number 15 , 16 &17. After executing the Tcode I could find that the field created in line 17 is not getting displayed in runtime. I have increased the screen length. The fields if moved to line numbers below 16 then they are getting displayed. Can anyone help me to find why it is not getting displayed after line 16.

Hi,
Can you give me the Enhancement name?
I searched for the exits using package , but i did not find any screen exists for that IW51 Tcode?

System should not allow to delete PO line Item after GR/IR

Hi,
I am working on a SAP Retail Implementation project.
Currently the system is allowing us to delete the PO line items after doing GR or IR against that PO line item. But the clients requirement is that the system should not allow to delete PO line item after doing GR/IR.
We are using Account Assignment Category-N, Item Category-S.
Please let me know if you have the solution for this requirement.
Thanks in advance
Thanks & Regards,
Suresh

Hi,
Standard SAP will not allowed the PO to be deleted once it was GR done. The controlled is on the attributes of message to set as "E"
Message no. 06115
But if invoiced takes place, the is the point that PO can be deleted.
You have to do have a Enhancement using MM06E005, insert you logic here to check PO history tables like EKBE, then check if invoice " Q" (BEWTP) exist, the PO cannot be deleted once the user delete the PO line and SAVE it. Ask you developer to help you on the following coding.
Use MM06E005 and EXIT_SAPMM06E_012
IF SY-TCODE = 'ME22N'.
IF sy-ucomm = 'MESAVE' OR SY-UCOMM = 'YES'..
LOOP AT TEKPO.
IF TEKPO-LOEKZ = 'L'.
SELECT SINGLE BELNR FROM EKBE INTO BELNR1 WHERE EBELN = TEKPO-EBELN AND EBELP = TEKPO-EBELP AND BEWTP = 'E'.
IF SY-SUBRC = 0.
SELECT SINGLE BELNR FROM EKBE INTO BELNR2 WHERE EBELN = TEKPO-EBELN AND EBELP = TEKPO-EBELP AND BEWTP = 'Q'.
IF SY-SUBRC = 0.
Regards,

I was logged in with a temporary profile on my pc, after restarting everything seemed to be fine. But my iTunes music is all in the cloud now, and my playlists are gone. What do I do?

I was logged in with a temporary profile on my pc, after restarting everything seemed to be fine. But my iTunes music is all in the cloud now, and my playlists are gone. What do I do?
My iTunes media folder shows ALL of my music still there (including all from imported CD's), but on my iTunes, it says most of it is in the cloud? As well as my playlists that I have had for YEARS, are all gone. I just recently got a new laptop and had my iTunes transferred over, when I re-downloaded iTunes onto it, everything popped up perfectly from this same file. Now after this "Temporary Profile" mishap, nothing is working properly with iTunes.
Help! Please.

Do this. If all the synced media like apps and music are alread in the the iTnunes library just backup the iPod and restore from that backup
iOS: How to back up and restore your content
Syncing to a "New" Computer or replacing a "crashed" Hard Drive: Apple Support Communities

Creating and Selecting a line in After Effects CC?

OK, So I suppose this is a two part question...
But there is a little thing in After Effects CC that is annopying me alot, and it could just be me, and the way I've been doing things...
1) The way I have creating a simple Line in After effects, is by using the pen tool, placing two points, and then just using a stroke on the Shape Layer, and no fill. Is this the most efficient way to creating a line in After Effects? It's what i have always done, and it's not until CC that it has been a pain.
2) The reason why it's inconveniencing me is when i try to select that Shape Layer in the Comp Viewer! For some reason, in CS6, when i wanted to select that line, i could just click on it, and it selects the layer, Now, when i click on the line i just made, nothing happens, no where in the line that i can click or highlight will it select the layer of that line, Instead, I have to click the very center of the composition for some reason. there is small unseen point there that i either have to click exactly, or click and drag in that area, in order to select the layer, which gets annoying if there are many line at any given moment. This point is also where the anchor point for the layer is placed.... Is there any way to change this? To be able to change some setting so that when i click on the line itself, it selects it, and to have the Anchor point be placed in the center of the two point i make?

But I do this kind of thing all the time. The last 5 projects involved 8 stroked horizontal and vertical shape layers drawn with the path tool that I had to move around the screen. I also had a bunch of little shapes that were only 5 X 5 pixels. These layers are nearly impossible to grab in the comp window at even 200% zoom factor without inadvertently grabbing the wrong layer or scaling the layer when you try to move it in the comp window.
It is like trying to drive a screw with a hammer. It will kind of work but you will do a much better job if you use a screwdriver and the screw will remain undamaged. Hence, selecting small assets in the timeline and moving them around with the transform properties from the timeline is using a screwdriver. Using the direct selection tool is just the wrong tool for this and it always has been. You have to have some real estate to grab on to if you expect to move a layer without scaling it.
You can mitigate the scaling problem for small layers by adding a simple expression to scale so the layer always stays at 100% but this will just automatically fix the scale problem and won't help moving the layer around in the comp window very much.

Font profile doesn't work after updating to ios 7.1

Before updating to ios 7.1 I can see text written in unicode zawgyi font in applications by installing the font profile. But after 7.1, text written in zawgyi unicode font appears as ?????. Some said removing and reinstalling the profile may help but it doesn't. The font appeared for a while when I first opened the app just before the font profile is installed but after restarting the app it showed ????? again. Please help me fix this problem.

hi Mr.Sianpu
nice to know you, my name Kiemtheng from Cambodia, i got a problem with Khmer Unicode font at my ipad which i just update from IOS 7.0.1 to ISO 7.1.1 , It not support with Khmer font which used to appear at the old version , the problem happen as the same Lian Tuang Question, and can you tell me how to fix this problem , hope to hear a good new from your, for khmer unicode font which support with Nokora and Battombong
http://adkhmer.com/app/iphone/font_khmer_ios7_no_jailbreak/Nokora.mobileconfig
https://docs.google.com/file/d/0B8798SqaxK-JS1B5T3hjNkJPQUE/edit?pli=1
thanks

Banded profile after line trouble after 3 days

Similar Messages

Maybe you are looking for