Bridge can't connect when roaming?

Not sure if this is a real problem with BB Bridge.
I'm overseas right now and the BB is on roaming mode with a foreign carrier. When I tried to connect the PB with it, I get the following message,
BlackBerry Bridge is Locked
Your BlackBerry smartphone could not be found
Please check that:
- Your BlackBerry smartphone is in range
- Your BlackBerry smartphone is turned on
- Your BlackBerry smartphone's Bluetooth connection is turned on
I've checked and everything is turned on. Could it be that when it's BB is roaming, the PB can't connect?
Anyone with similar experience?
Solved!
Go to Solution.

roaming should not affect bridge as it is a blue Tooth connection.
Then perform a Battery pull please, with the BlackBerry smartphone powered ON, remove the battery 15 seconds and then reinsert the battery to reboot device. This will clear all cache like rebooting a PC. Then try again and see if your problem persists.
on Playbook press power button and both Vol + - buttons for 10 seconds to reboot it.
if above dont work
delete the BlueTooth Bridge profiles on both devices
Then perform a Battery pull please, with the BlackBerry smartphone powered ON, remove the battery 15 seconds and then reinsert the battery to reboot device. This will clear all cache like rebooting a PC. Then try again and see if your problem persists.
on Playbook press power button and both Vol + - buttons for 10 seconds to reboot it.
setup bridge again and see if it persists.
Click here to Backup the data on your BlackBerry Device! It's important, and FREE!
Click "Accept as Solution" if your problem is solved. To give thanks, click thumbs up
Click to search the Knowledge Base at BTSC and click to Read The Fabulous Manuals
BESAdmin's, please make a signature with your BES environment info.
SIM Free BlackBerry Unlocking FAQ
Follow me on Twitter @knottyrope
Want to thank me? Buy my KnottyRope App here
BES 12 and BES 5.0.4 with Exchange 2010 and SQL 2012 Hyper V

Similar Messages

Can't Connect to "Roaming" Network

I have set up a new Airport "roaming"network. I have an Airport Extreme as the primary wireless router attached to the Internet. The Extreme is attached via ethernet cable to an Airport Express. I believe everything is set up according to Apple's instructions.
When I have both devices on, their status lights are green. However, if a device (iPhone, PC) is near the Express, it is asked to join the network and I have to re-enter the password. It will never connect.
If I take that same device and get near to the Extreme, it will connect, no problem.
Also, if I unplug, the Express, everything is OK (except my wireless coverage is not good enough in the house).
Any help would be greatly appreciated.

Let's double-check your roaming network configuration just to be sure nothing was missed.
Roaming Network Setup
Ref: See page 42 of the Apple AirPort Networks guide.
Setup the AirPort connected to the Internet to "Share a public IP address." Internet > Internet Connection > Connection Sharing: Share a public IP address
Setup the remaining AirPorts, as bridges. Internet > Internet Connection > Connection Sharing: Off (Bridge Mode) For each AEBSn in the roaming network:
For each base station:
Connect to the same subnet of the Ethernet network.
Provide a unique Base Station Name.
The Network Name (SSID) should be identical.
If using security, use the same security type (WEP, WPA, etc.) and password. Note: It is highly recommended that you use WPA2 Personal for best bandwidth performance.
Make sure that the channel is set at least three channels apart from the next base station to prevent Wi-Fi interference.

Sony Bridge Can't Connect To Internet After Updating To Mountain Lion

I've tried multiple times now, to get Sony Bridge to check for updates, but every time I try, I get the following error:
Cannot Check For Updates (no internet connection)
I'm on a 2008 iMac, connecting with a Live With Walkman.
My Mac is online and the problem only occurred after updating the OS to Mountain Lion (10.8).
Thus far I've tried going into the user library, and have deleted the two Sony folders present in the Application Support folder, but to no success, I still get the same error.
I'm firing this up regularly to see when ICS is going to drop in Belgium, so I'd be keen to hear of any possibile solutions. Thanks.

Hello OneManLaptop
ML came out 3 days ago...There is as of right now no tested version of Bridge for MAc available for it.
You will need to wait for the Update of the application but right now we can't provide a ETA for it.
Sorry for the inconvenience that this may cause you.
Francis.

Can't Connect When Specifying Database Name

Hi all,
I have an issue with an Oracle 9 database where I can connect if I do not specify a database to connect to but when i do specify one i get an error.
For example, my database is called WEB. If i open sqlplus and type connect username/password it will connect fine. If I type connect username/password@web I get an error.
The full error that appears in the log is:
TNS-12500: TNS:listener failed to start a dedicated server process
TNS-12546: TNS:permission denied
TNS-12560: TNS:protocol adapter error
TNS-00516: Permission denied
*32-bit Windows Error: 5: Input/output error*
I have checked the tns entries and listener file and both are fine. Here are the entries:
TNSNAMES:
WEB =
*(DESCRIPTION =*
*(ADDRESS_LIST =*
*(ADDRESS = (PROTOCOL = TCP)(HOST = localhost)(PORT = 1521))*
*(CONNECT_DATA =*
*(SERVER = DEDICATED)*
*(SERVICE_NAME = web)*
LISTENER:
LISTENER =
*(DESCRIPTION_LIST =*
*(DESCRIPTION =*
*(ADDRESS_LIST =*
*(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC0))*
*(ADDRESS_LIST =*
*(ADDRESS = (PROTOCOL = TCP)(HOST = localhost)(PORT = 1521))*
SID_LIST_LISTENER =
*(SID_LIST =*
*(SID_DESC =*
*(SID_NAME = PLSExtProc)*
*(ORACLE_HOME = D:\OraHome_1)*
*(PROGRAM = extproc)*
*(ENVS = "EXTPROC_DLLS=ANY")*
*(SID_DESC =*
*(GLOBAL_DBNAME = web)*
*(ORACLE_HOME = D:\OraHome_1)*
*(SID_NAME = web)*
This is on a Windows machine and I have checked and all the services are running. I have also checked the sqlnet.ora file for this entry:
SQLNET.AUTHENTICATION_SERVICES= (NONE) and tried it with NONE and NTS.
WEB is the only database on the Oracle server.
Can anyone suggest a solution to this problem?
Edited by: ThomasK on Jul 19, 2010 2:10 PM

Here are the results from the commands:
Microsoft Windows [Version 5.2.3790]
(C) Copyright 1985-2003 Microsoft Corp.
C:\Documents and Settings\ava>lsnrctl service
LSNRCTL for 32-bit Windows: Version 9.2.0.4.0 - Production on 19-JUL-2010 15:03:
33
Copyright (c) 1991, 2002, Oracle Corporation. All rights reserved.
Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC0)))
Services Summary...
Service "PLSExtProc" has 1 instance(s).
Instance "PLSExtProc", status UNKNOWN, has 1 handler(s) for this service...
Handler(s):
"DEDICATED" established:0 refused:0
LOCAL SERVER
Service "web" has 2 instance(s).
Instance "web", status UNKNOWN, has 1 handler(s) for this service...
Handler(s):
"DEDICATED" established:0 refused:0
LOCAL SERVER
Instance "web", status READY, has 1 handler(s) for this service...
Handler(s):
"DEDICATED" established:0 refused:5 state:ready
LOCAL SERVER
Service "webXDB" has 1 instance(s).
Instance "web", status READY, has 1 handler(s) for this service...
Handler(s):
"D000" established:0 refused:0 current:0 max:1002 state:ready
DISPATCHER <machine: 296508-WEB3, pid: 3812>
(ADDRESS=(PROTOCOL=tcp)(HOST=296508-web3)(PORT=2667))
The command completed successfully
C:\Documents and Settings\ava>set
ALLUSERSPROFILE=C:\Documents and Settings\All Users
APPDATA=C:\Documents and Settings\ava\Application Data
CLIENTNAME=SERENITY
ClusterLog=C:\WINDOWS\Cluster\cluster.log
CommonProgramFiles=C:\Program Files\Common Files
CommonProgramFiles(x86)=C:\Program Files (x86)\Common Files
COMPUTERNAME=296508-WEB3
ComSpec=C:\WINDOWS\system32\cmd.exe
FP_NO_HOST_CHECK=NO
HOMEDRIVE=C:
HOMEPATH=\Documents and Settings\ava
LOGONSERVER=\\296508-WEB3
NUMBER_OF_PROCESSORS=4
OPENSSL_CONF=C:\OpenSSL-Win32\bin\openssl.cfg
OS=Windows_NT
Path=D:\OraHome_1\bin;D:\OraHome_1\jre\1.3.1\bin;D:\OraHome_1\jre\1.1.8\bin;C:\P
rogram Files (x86)\Windows Resource Kits\Tools\;C:\Program Files\ava Tools\;
C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;C:\Program Files (x86)\D
ell\SysMgt\RAC5;C:\Program Files (x86)\Dell\SysMgt\oma\bin;C:\PHP;C:\PHP\ext;C:\
Program Files\MySQL\MySQL Server 5.1\bin;C:\PHP\libmcrypt.dll;C:\PHP\ext\php_mbs
tring.dll;C:\WINDOWS\system32\WindowsPowerShell\v1.0;C:\Program Files (x86)\Micr
osoft SQL Server\100\Tools\Binn\;C:\Program Files\Microsoft SQL Server\100\Tools
\Binn\;C:\Program Files\Microsoft SQL Server\100\DTS\Binn\;C:\Program Files (x86
)\Microsoft SQL Server\100\Tools\Binn\VSShell\Common7\IDE\;C:\Program Files (x86
)\Microsoft SQL Server\100\DTS\Binn\
PATHEXT=.COM;.EXE;.BAT;.CMD;.VBS;.VBE;.JS;.JSE;.WSF;.WSH;.PSC1;.VBS
PROCESSOR_ARCHITECTURE=AMD64
PROCESSOR_IDENTIFIER=EM64T Family 6 Model 15 Stepping 11, GenuineIntel
PROCESSOR_LEVEL=6
PROCESSOR_REVISION=0f0b
ProgramFiles=C:\Program Files
ProgramFiles(x86)=C:\Program Files (x86)
PROMPT=$P$G
SESSIONNAME=RDP-Tcp#3
SystemDrive=C:
SystemRoot=C:\WINDOWS
TEMP=C:\DOCUME~1\~1\LOCALS~1\Temp\1
TMP=C:\DOCUME~1\~1\LOCALS~1\Temp\1
USERDOMAIN=296508-WEB3
USERNAME=ava
USERPROFILE=C:\Documents and Settings\ava
windir=C:\WINDOWS
C:\Documents and Settings\ava>tnsping web
TNS Ping Utility for 32-bit Windows: Version 9.2.0.4.0 - Production on 19-JUL-20
10 15:03:33
Copyright (c) 1997 Oracle Corporation. All rights reserved.
Used parameter files:
D:\OraHome_1\network\admin\sqlnet.ora
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)
(HOST = localhost)(PORT = 1521))) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_
NAME = web)))
OK (0 msec)
C:\Documents and Settings\ava>ping 296508-web3
Pinging 296508-web3 [192.168.100.42] with 32 bytes of data:
Reply from 192.168.100.42: bytes=32 time<1ms TTL=128
Reply from 192.168.100.42: bytes=32 time<1ms TTL=128
Reply from 192.168.100.42: bytes=32 time<1ms TTL=128
Reply from 192.168.100.42: bytes=32 time<1ms TTL=128
Ping statistics for 192.168.100.42:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
C:\Documents and Settings\ava>lsnrctl status

Can't connect when on campus

I have no problem with my secure wireless network at home. Likewise no issues connecting to a friend's wireless at their home. However, when I take it to school it cannot connect. My macbook pro has no problems at school, nor does my ipod touch. I have to log into their network using my credentials using the notebook or touch, and I get the window asking for my credentials on the ipad, but when I enter them and click OK nothing happens. There's not even a busy icon of any kind. Any ideas would be appreciated.
Cheers,
Jennifer

Hi jmweber,
Welcome to the Apple Discussions.
Ok Lets talk about the home situation and work outwards from there.
You get what is called Public IP from your ISP.
Your modem or a router can then divide this to your computers by creating your Private LAN by issuing IP numbers itself.
NAT (Network Address Translation) is the software that achieves this in the modem or router.
Mostly in domestic devices this really kicks in on the ports above the 1024 threshold.
This tends to mean that Web browsing on port 80 is allowed for everyone (computer) that is connected to the modem.
On-line games plus other apps like Instant Messengers use ports above this threshold and need the ports opened/allowed
On Commercial devices it is possible to do NAT down to the lowest port numbers.
OK Now some ways of opening or allowing the ports above 1024 use NAT more than others due to the way the Addressing info is added to the packets.
Port Forwarding and Port Triggering both rely on NAT (DMZ is an extreme form of Port Forwarding)
Then you have the fact that some manufacturers achieve NAT differently. Sometime you get devices that just don't "Play Nicely", creating the Certain Buddy Problem.
http://www.ralphjohnsuk.dsl.pipex.com/page15.html#CertainBuddy
I would use UPnP in devices if they have, where you can.
UPnP (Universal Plug n Play) allows the applications to control the modem ports at not use NAT (Or at least not in a way that effects things in iChat)
7:09 PM Thursday; January 11, 2007

Deluge-console can't connect when running daemon

To date, I have always run deluged as my user. I started the deluged daemon (rc.d start deluged) but find myself unable to connect via deluge-console.
[ERROR ] 10:05:50 client:393 RPCError Message Received!
RPCRequest: daemon.login(, )
File "/usr/lib/python2.7/site-packages/deluge/core/rpcserver.py", line 259, in dispatch
ret = component.get("AuthManager").authorize(*args, **kwargs)
File "/usr/lib/python2.7/site-packages/deluge/core/authmanager.py", line 87, in authorize
raise BadLoginError("Username does not exist")
BadLoginError: Username does not exist
The wiki offers no guidance on deluge-console. Is this expected behavior? The gtk client works fine btw.

While searching for the problem, I crossed your thread and thereafter, found a solution :
Launch deluge-console as usual.
It will throw the error, but you can still use the deluge shell, so connect to the daemon using this command :
connect localhost user password
Replace localhost by the host if it's a remote machine, user and password by the ones you use in the authentification config of Deluge.

HT1595 Apple TV loses complete internet connection every 5 minutes. Tried restarting. Tried unplugging the router, unplugging the modem, and unplugging Apple TV and it still does't work. Get error message 22 saying it can't connect when I put in my pas

It only connects for minutes at a time. I have not changed my router, modem, or placement of my apple tv, modem, or router. It just suddenly stopped working. Any suggestions?

Mine is doing the exact same problem!
Ever since I rented a movie from itunes with the ATV connected to the internet via wireless (strong signal) from an airport extreme connected to my modem from charter communications (with about 30Mbps speed) it will suddenly stop and by stop I mean it leaves the movie completely and says YOUR APPLE TV IS NOT CONNECTED TO THE INTERNET.
So if I go to my network in the apple tv menu, sure enough my wireless network is missing. But the ipad is finding it, and the imac on wireless is finding it, and it is working. So we hit restart on the apple tv. When it comes back all is good. Then maybe the movie runs ten minutes and it does it again.
In some cases the wireless network reappears but if I select it it still says I'm not connected to the internet.
I have to restart everytime or it will not properly reconnect to the internet or find my wireless net work and actually work and connect.
It has been connected in the same place for a year and never had an issue.
Nothing has changed..... I have not added a wall to cause interference....
My iPad and iPhone show FULL strength.
Please help!

Can't connect when it says it's connected

Sometimes my computer says it's connected to the internet but it doesn't work. I have to use the repair button constantly and once in a while the same thing happens again. Could someone tell me if there is a solution and how to fix it? Thanks.
Model: WRT54G

Change the Wireless Settings on your router and try to re-connect to your Network...
Open an Internet Explorer browser page on your wired computer(desktop)...In the address bar type - 192.168.1.1
Leave username blank & in password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
Wireless Network mode should be mixed...Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
Change the channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WEP, Encryption should be 64 bits.Leave the passphrase blank, don't type in anything...
Under WEP Key 1 type in any 10 numbers please(numbers only and no letters eg: your 10 digit phone number) and click on save settings...
Please make a note of WEP Key 1 as this is the Security Key for the Wireless Network...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
Now see if you can locate your Wireless Network and attempt to connect...Make sure your Wireless Network Connection is set to Obtain IP Address automatically...
If the above fails, you need to upgrade your router's firmware...
Download your router's firmware from here
Follow these steps to upgrade the firmware on the device: -
Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave the username blank & in password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...Also do the above Wireless Settings...

Airport Express as a wireless bridge can't connect using the 2.4GHz band

I have an Airport Extreme with simultaneous dual-band support as well as an Airport Express serving as a wireless bridge to extend the range of my primary base station.

By the way, the 5GHz band does not penetrate very well,
That is not surprising since the higher frequency signals are not as strong as 2.4 GHz signals. Many users are finding that you almost have to have a line-of-sight situation between the computer and router for 5 GHz to work really well.
and the signal becomes weaker significantly after it penetrates through two walls.
Again, not surprising. What is surprising is that the AirPort Express was choosing the 5 GHz band to "extend", as it normally latches onto the stronger of the two signals, which almost always the 2.4 GHz signal.
You may be correct that the newer firmware has made some changes in this regard. My guess would be that most users were trying to extend the 5 GHz band and not having much success. We'll keep an eye on this.

Upraded Sql Developer and can't connect to Oracle

I just updated to the Dec 2009 release and now I can't connect
When I click the plus or right click on Connections and select "New Connection" nothing happens.
If I monitor processes in task manager it shows a brief spike in cpus and a small increase in memory usage but nothing happens in the app.
I also noticed that when I close the application it does not leave memory. I have to kill the process via the task manager to get rid of it.
If I go back to version 1.5.1 it works fine. It also leaves memory when terminated
Using winxp r3.

Here is the beginning of the output:
E:\sqldeveloper\sqldeveloper\bin>sqldeveloper
Feb 24, 2010 8:30:27 AM javax.ide.extension.ElementVisitor log
SEVERE: jar:/file:/E:/sqldeveloper/sqldeveloper/extensions/oracle.sqldeveloper.snippet.jar!/META-INF/extension.xml:16: Duplicate declaration of addin
oracle.dbtools.raptor.snippet.SnippetAddin. Previously defined in extension oracle.dbdev.snippet
Feb 24, 2010 8:30:27 AM javax.ide.extension.ElementVisitor log
SEVERE: jar:/file:/E:/sqldeveloper/sqldeveloper/extensions/oracle.sqldeveloper.snippet.jar!/META-INF/extension.xml:17: Duplicate declaration of addin
oracle.dbtools.raptor.snippet.SaveSnippetAddin. Previously defined in extension oracle.dbdev.snippet
Feb 24, 2010 8:30:27 AM javax.ide.extension.ElementVisitor log
SEVERE: jar:/file:/E:/sqldeveloper/sqldeveloper/extensions/oracle.sqldeveloper.migration.jar!/META-INF/extension.xml:16: Duplicate declaration of addi
n oracle.dbtools.migration.workbench.core.MigrationAddin. Previously defined in extension oracle.dbtools.migration
Feb 24, 2010 8:30:27 AM javax.ide.extension.spi.SAXManifestParser$Handler endElement
SEVERE: jar:/file:/E:/sqldeveloper/sqldeveloper/extensions/oracle.sqldeveloper.migration.jar!/META-INF/extension.xml:22: Exception processing manifest
: java.lang.NumberFormatException:For input string: "VIEW_CATEGORY_MENU"
java.lang.NumberFormatException: For input string: "VIEW_CATEGORY_MENU"
at java.lang.NumberFormatException.forInputString(NumberFormatException.java:48)
at java.lang.Integer.parseInt(Integer.java:447)
at java.lang.Integer.parseInt(Integer.java:497)
at oracle.ide.util.ArrayResourceBundle.handleGetObject(ArrayResourceBundle.java:495)
at java.util.ResourceBundle.getObject(ResourceBundle.java:378)
at java.util.ResourceBundle.getString(ResourceBundle.java:344)
Here is a snip from partway down:
Exception initializing 'oracle.jdevimpl.runner.profile.ProfilerShell' in extension 'Database Developer': oracle.classloader.util.AnnotatedNoClassDefFo
undError:
Missing class: oracle.jdevimpl.runner.profile.ProfArb
Dependent class: oracle.jdevimpl.runner.profile.ProfilerShell
Loader: ide-global:11.1.1.0.0
Code-Source: /E:/sqldeveloper/jdev/extensions/oracle.onlinedb.jar
Configuration: extension jar in E:\sqldeveloper\jdev\extensions
The missing class is not available from any code-source or loader in the system.
at oracle.classloader.PolicyClassLoader.handleClassNotFound (PolicyClassLoader.java:2180) [/E:/sqldeveloper/modules/oracle.classloader_11.1.1.
jar (from system property java.class.path), by sun.misc.Launcher$AppClassLoader@24216257]
at oracle.classloader.PolicyClassLoader.internalLoadClass (PolicyClassLoader.java:1733) [/E:/sqldeveloper/modules/oracle.classloader_11.1.1.ja
r (from system property java.class.path), by sun.misc.Launcher$AppClassLoader@24216257]
at oracle.classloader.PolicyClassLoader.access$000 (PolicyClassLoader.java:143) [/E:/sqldeveloper/modules/oracle.classloader_11.1.1.jar (from
system property java.class.path), by sun.misc.Launcher$AppClassLoader@24216257]
at oracle.classloader.PolicyClassLoader$LoadClassAction.run (PolicyClassLoader.java:331) [/E:/sqldeveloper/modules/oracle.classloader_11.1.1.j
ar (from system property java.class.path), by sun.misc.Launcher$AppClassLoader@24216257]
at java.security.AccessController.doPrivileged (Native method) [unknown, by unknown]
at oracle.classloader.PolicyClassLoader.loadClass (PolicyClassLoader.java:1692) [/E:/sqldeveloper/modules/oracle.classloader_11.1.1.jar (from
system property java.class.path), by sun.misc.Launcher$AppClassLoader@24216257]
at oracle.classloader.PolicyClassLoader.loadClass (PolicyClassLoader.java:1674) [/E:/sqldeveloper/modules/oracle.classloader_11.1.1.jar (from
system property java.class.path), by sun.misc.Launcher$AppClassLoader@24216257]
at java.lang.ClassLoader.loadClassInternal (ClassLoader.java:320) [jre bootstrap, by jre.bootstrap:1.6.0_10]
at oracle.jdevimpl.runner.profile.ProfilerShell.createRunMenuItem (ProfilerShell.java:193) [/E:/sqldeveloper/jdev/extensions/oracle.onlinedb.j
ar (from extension jar in E:\sqldeveloper\jdev\extensions), by ide-global:11.1.1.0.0]
There are around 500 lines of output none of which tells me what is wrong

Can't connect to computer through wireless network

I recently purchased a Powerbook G4 with OS X Server 10.4.6 installed, and I cannot connect to my iMac G5, which has OS X 10.4.6 installed. I am trying to connect them wirelessly, and it sees the G5, but tells me that it is offline and can't connect when I try. I can connect to the Powerbook through the iMac, but not the other way around. Tried different share settings on G4, but am quite unfamiliar with OS X Server. Any help would be appreciated.
Thanks.

It seems like you may not have the relevant service(s) enabled in Sharing preferences on your iMac, if I understand your problem correctly. The settings on the server, other than firewall, shouldn't matter for outgoing connections.

3109 can't connect to PC Suite

I am on my third 3109 and have always used PC Suite, no problems with the others. The latest one I have named the same (bluetooth) as before and set to visible. I have connected it and paired to my laptop, as I always do. Then when I search for devices in PC Suite - I see 2 phones called silvercue. One says it needs to be connected, but is greyed out and the other says it needs to be connected and authorised and is greyed out.
I have restarted the phone and PC Suite - always the same. I can't connect, when the phone is, or is not connected to the laptop.
What is wrong? This is the same process I have always used with identical handsets and always used the same phone name with no issues.
Thanks in advance.
PS - I did search, but could see the answer.

Hi,
I have some problems with the connection but in this moment, I am working "well".
First: Please use the Driver included in the CD with the Original Cable. Not use the driver downloaded from the site.
Second: When you connect the cable in the phone, you will received a error message, ignore it, wait near one minut and you see a message "Nokia 6103 is connected" in your PC
Third: To disconnect the phone, first go to "Admin Conecctions" in the Nokia PC Suite and unheck "Serial Cable (CA-42)", when you received a message of desconnectio, you can unplug the cable from the phone.
Bye.
EDUARDO.

Skype can't connect - most likely router problem, ...

Lately I can't connect to Skype at home. I've tried a lot of different solutions but none of them work.
The problem started a few months ago when I just couldn't sign into Skype (can't connect). At that time I had no change in any network settings on my computer nor my router. Interestingly enough, I could connect to Skype on Ubuntu (I have dualboot). Though even Ubuntu eventually failed to connect back then (just can't sign in) - still no changes in my network. I couldn't be bothered at the time with the problem so I just didn't use Skype.
However after some time (some weeks or a month or two), when I tried to connect to Skype again, it worked (on Win 7 as well as Ubuntu). Again, no changes to my network have been done in the mean time (Skype might of been updated, but I doubt it was on both platforms at the same time).
So Skype worked for a while until about a month ago, when the problem reoccurred. This time I said I'm going to get to the bottom of this so here is the situation:
I can connect to Skype at work no problem (on my desktop as well as my Android phone)
I can't connect to Skype at home (just won't sign in) on my desktop nor my phone
I have tried:
Reinstalling Skype with cleaning everything that Skype might have left behind
Installing an (a bit) older version 6.9 (because even the latest 6.11 didn't work). Though these two attempts I've come to see are in vain once I figured out that I can't connect to Skype on my phone as well.
Resetted my router a couple of times.
Reset my router settings to default.
Opened/forwarded Skype ports to my (local) IP. I even enabled DMZ to redirected all traffic to my desktop computer (although I'm not 100% sure that that worked as I imagine it should work).
Tried some proxy settings in Skype (Connection options) I found on your forum.
None of the above worked in any way...
My router is a TP-Link TL-WR1043ND with (I think the latest) firmware version 3.13.13 Build 130428 Rel.58290n (hardware is v1).
TLDR:
I can't sign in to Skype at home. It works when I'm at work. I can connect to Skype on my phone if I'm at work (over WiFi) or if I'm on 3G, but not if I'm on my home WiFi. That said, no software firewall can be the problem here, but my router. However I have no more ideas as to what else I can try. This forum is my last hope for finding a solution.
Please help.
Solved!
Go to Solution.

I do not know the makeup of Skype's internal security policies when it comes to this as they are not too open about this. Most companies are not. These are the only reasons I believe a block would occur based off any company's security policy.
1. A proactive measure - A blacklist of IPs is constantly obtained/updated to include anonymizer services that might harm the network.
2. An active/counteractive measure -
I. Someone uses an anonymizer to SPAM people on the Skype network:
a. Users complain using the abuse option. Users get the IP Auto-banned.
b. The company (Skype) receives the complaints or notices a trend and Manual/Auto bans the IP.
II. Too many people (connections) sign on with the same IP (due to an exit relay/proxy). Due to this being very suspicious, (maybe even DDos-like behavior) the IP is Auto-banned.
I tend to lean more towards the counteractive measure since I don't believe many proactive measures are needed to limit abuse. There is always at least one rotten apple that engages in illegal activity using anonymizers, proxies, etc. that ruin it for everybody. In reality I believe it is a combination/balance of the two. Not to be prejudice against anonymizers, just blacklists to protect the network from known attacks. For whatever reason once the threshold is met, the IP is banned. If I had to guess how long it would be in intervals of 30 days (30, 60, 90, 120, etc.). The whole Internet is not going to banned so the security policies in effect can't be too strict. It's goal is probably just to limit the majority of bad behavior that causes problems for their customers.
Skype is not the only service that reacts this way. Even ISPs will receive notices and in turn will send notices to their customer that since illegal activity (RIAA notices, etc.) is occurring due to a Tor exit relay or some other anonymizer, the ISP will terminate services with that customer if they don't cease (due to breach of contract).
I don't know whether you can limit an exit relay so it can't be used to access Skype. It may be a lost cause. If I made the choice to run a similar service it would be with a whitelist of people I knew who wouldn't use it to perform illegal activity, just remain anonymous when online.
You shouldn't have any issues running a non exit relay since in doing so your IP is not being broadcast all over the Internet like a calling card which an exit relay does. Changing your modem's MAC address is something you need to call your ISP for. However changing your router's MAC address generally does not require that. All that is required is a reboot of the modem, router, and possibly computer if you run into issues. You will probably continue to run into the same problem as long as you attempt to run an exit relay.
Be aware that for every IP that get's banned on your ISP is another IP a person could get issued for 24 hours to a week + after it gets released. Some people then visit this community and complain how they can't connect when it worked not too long ago and how Skype "sucks". So sometimes things like this create a ripple effect for other customers.

Can't connect using differnet startup disk!

I archived everything to wipe some drives clean and manually migrate. Its done wonders to speed up my Quicksilver G4.
I reinstalled Tiger on the old orginal drive (should fail sometime soon; its five years old) and also on a Maxtor 120g (much newer). Strangely, I can't connect when using the Maxtor as the startup drive. Network diagnostics tell me that my ethernet cables aren't connected, among other oddities, such as constantly changing data in the Setup Assistant pane.
When I installed Tiger on the Maxtor, communication with Apple and .Mac was fine (retrieved all account info), but Safari wouldn't connect.
The Maxtor used to have two partitions and was my main startup drive which I archived and zeroed out.
It gets stranger. My MacPro also won't connect if the G4 is unable to connect using the Maxtor! When I go back to using the original IBM Apple drive, everything connects beautifully.
When trying to access the router via browser, using the IBM of course is fine, but using the newly formatted Maxtor, I can't gain access.
MacPro and G4 are connected via ethernet to a DLink DI 624; ISP is Verizon FIOS (which is killer, btw).
Any ideas are much appreciated. BD Aqua?

In passing I'll mention that different brand Drives mixed can have bizarre results with CS or M/S, and though Apple swears you should use CS, (some drives won't boot if NOT CS), I've had to do the opposite on some of mine... or seperate them to different buses.
Back to the problem, (not sure it's a good install because of the Mix!), but 1st I'd get what's my ip...
http://www.whatsmyip.org/
If that didn't work then I'd try trashing...
/Users/nnnn/Library/Preferences... the whole Prefs folder there.
/Library/Preferences/SystemConfiguration... the whole SysConfig folder.
/Library/Preferences/SystemConfiguration/NetworkInterfaces.plist
/Library/Preferences/com.apple.sharing.firewall.plist
/Library/Preferences/com.apple.AppleFileServer.plist
Reboot... of course you dont have to trash them, you can just move them to the desktop to drag back if it doesn't work.
If that doesn't work, I'd ZERO the drive and reinstall.
PS.How long ago where you here_ I think you wouldn't care for little LA that runs from Canada to Oregon now!

HT3477 I am attempting to set up a guest network. When I change the Network settings to DHCP NAT I get a message that tells me that the service has a private IP address and so I must connect using off bridge mode. In this mode I can not connect to the int

I am attempting to set up a guest network on the Airport Extreme Base Station. The Base Station is connected to a DSL Modem. The network is also extended using an Airport Express. When I have attempted to set up the Base Station using DHCP NAT in the netword feature I get a message that because the service has a private IP address the only way that I can connect is in Off Bridge Mode. In this mode I do not seem to be able to connect to the internet using the guest network. Any suggestions would be helpful.

Ok, your Speedport is actually a combination DSL modem and wireless router. In this case you would typically configure a downstream router, like your AirPort Extreme in Bridge mode. Unfortunately, when in Bridge mode, the AirPort does NOT support providing a guest network.
The only possible option is to reconfigure the Speedport as a bridge and use the Extreme as your Internet router. You would still need the DSL modem provided by the Speedport for Internet connectivity.

Bridge can't connect when roaming?

Similar Messages

Maybe you are looking for