Cannot connect to remote servers or exchange email?

I have the same issue and can connect via any other connection including Att hotspots, wifi etc etc. I do not think the issue is related to my system and to clarify, I am not connecting via VPN. Any help on this is greatly appreciated.

VZW mobile broadband devices sit behind a NAT firewall. The NAT hides your public IP Address and the firewall blocks custom ports from communicating to devices on the VZW network. Pending on what you are trying to do on your remote servers or exchange servers one of the other is likely broken due to the nature of the VZW network.
The work around is to setup a VPN to a VPN server that allows you to make the customizations that you need to support your applications. That or buy a static IP address from VZW for $500. That or configure your applications to communicate over the internet over more traditional protocols and ports.
Contact your system or network administrators in charge of your remote servers to find out what the requirements are for connecting to them. See if they can offer you any work arounds or custom configurations. Chances are others have the same limitation and they already have something cooked up to work around it.

Similar Messages

Cannot connect to hamachi servers

I try to connect to the servers I uninstall and install three times but it still does not work and I cannot connect to the servers while my friends can pls help

The activation servers are probably overloaded with everyone trying to update to iOS 7 today. You might need to wait and try again later.

Users cannot connect to shares or sync Exchange via company wifi

Hello, I am posting this because my users can connect to the company wifi (guest and private) with no problem. They can use the internet, but nobody can reach network shares, nor can they setup or sync Exchange email via the wifi. Currently, anybody with a smartphone must be on 3g or 4g in order to get their email onsite. Laptops with wifi capability must be connected via ethernet cable in order to get to network shares and email. I've searched and searched, but cannot find anything on this. Anyone have ideas?

Hi Luis,
I am using a Cisco ASA 5510 with two Cisco AP 2600's. After digging in their configuration settings, I was able to see that the AP's IP addresses are completely different than our internal IP's, which would explain why Exchange isn't able to sync. Unless I am misunderstanding how they work, shouldn't they be giving out the same Ip scheme as the ASA? (i.e. ASA IP scheme: 10.0.10.XXX, AP IP scheme: 174.XXX.XXX.XXX)
Your help is greatly appreciated.
Thank you,
Jye

Cannot connect to remote server

When trying to make connection to remote server, I receive a
message, "FTP, error, cannot make connection to host-Logon and
Password are incorrect... However, settings are correct as I could
get on in the past and when testing for remote site in site
management the message states "Adobe DW Cs3 connected to your web
server correctly".
My OS is MAC 10.4.11 My site developer can get on with DW8
using a PC and a MAC. Have tried everything short of deactivation
and reinstall.

Plese tell us what your remote site definition has in each
field (you can
omit the password).
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
==================
"TJMax412" <[email protected]> wrote in
message
news:gbtj7m$94l$[email protected]..
> When trying to make connection to remote server, I
receive a message,
> "FTP,
> error, cannot make connection to host-Logon and Password
are incorrect...
> However, settings are correct as I could get on in the
past and when
> testing
> for remote site in site management the message states
"Adobe DW Cs3
> connected
> to your web server correctly".
> My OS is MAC 10.4.11 My site developer can get on with
DW8 using a PC and
> a
> MAC. Have tried everything short of deactivation and
reinstall.
>

After 10.6 update, cannot connect to remote speakers

After I updated itunes on my windows 7 (64 bit) machine to version 10.6.1.7, itunes does not show my remote speakers connected through an airport express. My windows XP machine with itunes version 10.5.3.3 does show my remote speakers and can stream music to them through the airport express. Both machines are on the same network behined the same firewall. Furthermore all other "i" products in the house can stream through the airport express to the remote speakers (2 iphones & 2 ipads). Nothing has changes except for the Win 7 itunes upgrade to 10.6.1.7. Is there a way to roll back the itunes upgrade? Or is there a fix for 10.6.1.7?

Ok, I've just done that. An error message came up, with half an email address so I changed the year date back and opened passbook.. Then it asked to connect to iTunes, it didn't display the "cannot connect.." message, just showed loading and the wheel going around for ages. Regretting this update, so much hassle. Thank you for your help so far though. Seems like so many people are having the same problems :(

ITunes cannot connect to remote speakers / Airport Express

Hi Guys
This is a quick post with a problem & solution.
I've been searching for ages tonight to find a solution to my problem:
'iTunes suddenly cannot connect to my Airport Express Speakers" and could not find one answer on here, only a mixture of replies all over the net.
So, just incase some people are still looking for an answer:
What I did...
1. Go to System Preferences, Network.
2. Click Advanced, on the TCP/IP tab, set "Configure IPv6" to Off.
Open up Airport Utility, go to the Music tab, set a password (I did this just for the sake of seeing whether iTunes noticed that the Airport was now password protected, then atleast you know it's talking!)
3. Open iTunes, go to preferences.
4. Click on the devices tab, untick "Look for remote speakers connected with Airplay, Allow iTunes control from Remote Speakers, Forget All Remotes.
5. Close iTunes
6. Open iTunes, retick "Look for remote speakers connected with Airplay, Allow iTunes control from Remote Speakers, Forget All Remotes.
7. Connect to remote speakers worked!

thanks Simius,
I just tried what you said to do, i had it in Automatic, but when I momenterely switched to manual the fields were all blank so I left them that way and turned on to automatic as you said and left it in auto, then tried to change itunes speaker to remote airplay and it didn t work.
so i don t know what else to do, I read alot about this in the last few days the bug seems to be related to the newest itunes upgrade and with the presence of the IP6V not turned off completely.
in the old system one could turn it off completely, now the off button is gone.
there are work around using terminal, I tried that but it doens t recognize my commands, so it didn t work either.
anybody has any idea?
thansk a lot
D.

Cannot connect VIA Remote Desktop to Windows 8.1 on a virtual machine

I have Windows 8.1 Enterprise running in a Hyper-V VM. For some reason I cannot connect to the VM using remote desktop. I am using a Microsoft account and remote desktop is enabled and my account has access. I am able to see the VM under
networks and access shared folders. The error I am getting is "Remote Desktop can't connect to the remote computer....".
Any ideas?

My account has access to RDP. The firewall rule to allow RDP was missing the permission for public networks. After this change the RDP client can find the computer and I can get in. Yay!
Thanks for the tip to check the firewall.

Portege R500: cannot connect the remote DVI monitor via Dynadock

Hello,
I just connected Dynadock (DVI) with my Portege R500. The notebook would be supported -- according to Toshiba -- but my experiment confirms that Dynadock is not able to access DVI port. This implies, that Dynadock is nothing more than USB HUB.
My setup: Vista 32b Business (CZE edition), latest fixes, Toshiba R500.
Software: latest dynadock software 2.3c.
Symptom: I cannot connect to the remote DVI monitor via the dynadock, only two external panels with 800x600 are available, but Vista does not allow me to choose them.
More info: Dynadock Software requires to run without Microsoft Defender, else it blocks service:DisplayLinkService; file:C:\Program Files\DisplayLink Core Software\DisplayLinkService.exe
If you disable MSDef, the message "error 2738" appears when you connect the dynadock and when Vista tries to install a missing drivers for you.
Yes, I do know the VBS issue, and the problem is not caused by VisualBasic -- VBS "Hello World" runs.
If you still believe, that Toshiba Dynadock is compatible with Toshiba R500, then press Fn-F5 and peek at your logs and you must find something like:
In English: igfxext.exe throws an exception 0xc000000d, offset 0x0000f9f8.
I welcome any comments, hints etc. If you are able to pass this bug report to a responsible engineer, do so please.

Hello again Leo
I still believe you are wrong. Toshiba Dynadock is not designed for Toshiba products only. It is universal product and can be used on every notebook. To be honest I believe it is better to use it with new, more powerful, notebooks.
When you sat your notebook model is listed as compatible I believe you. Why not? Toshiba can list all newer notebooks. No problem at all. To be honest I am also interested to buy Dynadock but after reading your posting I wanted to see how it works exactly.
I have contacted my friend because he works in one big electronic store and I was lucky because he had Portege M500 too.
He was very nice and offered me to test Portege M500 SSD model with Dynadck PA3542EY1PRP. I hope you have the same model. It is DVI model. So I have done follow:
- Portege was preinstalled with clean Vista OS (factory settings started for the first time)
- I have installed latest Dynadock Utilitiy for Vista 2.3c
- Installing this software you must pay attention about installations steps and the installations procedure should not be interrupted
at one step there is window Installation Complete but it is not complete and must be continued with
Display Link Core Software installation
Video Dock installation
at this point the Dynadock must be connected to favorite USB port NOT FROM THE BEGINNING
- At the end I have restarted notebook
The installation was finished properly and I have connected 20 Toshiba Tekbright LCD display (DVI cable). The native resolution is 1680x1050. in Display properties there are shown three displays. Display number 3 belongs to display connected to the Dynadock.
Resolution 1680x1050 was there and display shows perfect picture. I have tested it as extended desktop and it works without problems. I didnt test it playing some movies.
I have also tested it with FN+F5 key combination. It does not work as it should be but there is definitely no error message. I know that FN+F5 key combination is not designed for external graphic card and I know that it can not work well.
At the end I can sat that Dynadock works well with Portege M500 SSD and there is definitely no error message. It works with Vista very well. I have tested it with screen saver and with few restarts. Nothing changes. Everything was OK.
So after this test I can say that you have done some mistake. If you want to use it again I recommend you to install Vista again using recovery image. After doing this you will have clean preinstalled OS. Install software but please follow the menu on the screen and be sure all three components are installed properly. If I am remembering well when you see message about USB audio device installation you must connect Dynadock and continue installation.
PLEASE FOE DYNADOCK USE ALWAYS THE SAME USB PORT!!!
Sorry for this long story but I can say for sure IT WORKS PROPERLY!!!
Have a nice day!

After 7.0.6 upgrade Icloud email "Cannot Connect To Server". All other email works fine.

After upgrade to 7.0.6 both IPad and iPhone now will not send or receive Icloud email while at home. Get "Cannot connect to server " message. All other email accounts (google, verizon) work fine. Plus the "last backup" information unavailable as well as icloud storage information. Says unavailable, try again later. Also cannot view body of emails sent or received in the last 2 days. I am at work now and all works normally. If this is a wifi issue, I I do not understand why all other email accounts are sending receiving ok. It's only the Icloud server that seems to be the problem.

Hey there KevGelay!
I have an article for you that will help you troubleshoot this issue with your ability to access iCloud mail:
iCloud: Troubleshooting iCloud Mail
http://support.apple.com/kb/ts4002
Take care, and thanks for visiting the Apple Support Communities.
-Braden

TS3899 Cannot connect to server. Can send emails but unble to receive any on iCloud account .

Keep getting message 'cannot connect to server' can send emails on iCloud but not receive them.
Help please.
Belgar2

iOS: Unable to send or receive email
http://support.apple.com/kb/TS3899
Can’t Send Emails on iPad – Troubleshooting Steps
http://ipadhelp.com/ipad-help/ipad-cant-send-emails-troubleshooting-steps/
Setting up and troubleshooting Mail
http://www.apple.com/support/ipad/assistant/mail/
Why Does My iPad Say "Cannot Connect to Server"?
http://www.ehow.co.uk/info_8693415_ipad-say-cannot-connect-server.html
iPad Mail
http://www.apple.com/support/ipad/mail/
Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
Or this - Delete the account in Mail and then set it up again. Settings->Mail, Contacts, Calendars -> Accounts Tap on the Account, then on the red button that says Remove Account.
 Cheers, Tom

My iPad is telling that it cannot connect to server when checking for emails but I can connect to the internet

My email was working great, I tried sending a large attachment and couldn't, I cleared that and now my email cannot connect to server, internet is working fine, any suggestions?

Sometimes it helps to close the mail app and reboot the iPad. That will reset the app and the iOS system. Try mail again after that.
Double tap the home button and you will see apps lined up going left to right across the screen. Swipe to get to the Mail app and then swipe "up" on the app preview thumbnail to close it.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.

HT1947 Cannot connect to "Remote" App to iTunes 11

After I have upgraded to iTunes 11, the "Remote" app cannot connect to iTunes 11. I hav edeleted the app, and re-download it. It asks me to key in the 4-digit code on iTunes. But I cannot find the Device List any more in iTunes 11. Anyone knows how to resolve this.

It turns out that the "Remote" app has adopted the "Home Sharing" function instead of using a 4-digit code to pair an iDevices with the iTunes.
But my problem had more twists and turns. Initially, I thought that it was Norton firewall that blocked the "Home Sharing". After many trials, I found that the Actiontec router supplied for Verizon FIOS blocked the "Home Sharing". After I disabled the IGMP proxy in router, everything worked as designed. I would have never figured this one out. Thanks everyone for posting on the different forums.
http://forums.verizon.com/t5/FiOS-Internet/Communication-between-wired-and-wirel ess-network-on-actiontec/td-p/461359

-3256 Error - Unknown error, cannot connect to remote speaker

I recently bought time capsule and have set that up as a base station. The input to time capsule is the linksys modem + router. I have disabled the linksys router capabilities and am only using that as a modem. When i connect airport express to the time capsule network, i get a error message stating -3256. Unknown error cannot connect to the remote speaker. Before time capsule, linksys network was able to play airtunes, but time capsule is not able to. I have disabled the firewall on both time capsule and linksys.

It might actually be the firewall on your mac rather than the other hardware. I mysteriously started getting this same error when trying to use the Multiple Speakers function with AirTunes (had worked perfectly for over a year). I modified the Security/Firewall settings in System Preferences and it started working again, no error: I simply added iTunes to the "specific services" firewall list to allow incoming connections. Of course the firewall is set up quite differently in 10.4.x.
You'd think that checking "look for remote speakers" in iTunes preferences would take care of this for you, or prompt you to make the changes yourself (I remember getting OS messages that used to say "if you want to do such-and-such, make sure you open port xxxx") but apparently not!
I also read somewhere that checking "share my library" in iTunes prefs can help with this sometimes, but I can't verify that - I already had it checked; it was the OS firewall tweak that worked for me.

Cannot Connect to Remote Named Instance of SQL Server

We have 3x instances of SQL Server 2012 installed on a single remote server - there's the default MSSQLSERVER instance, then \INSTANCE01 and \INSTANCE02. I can remotely connect to the default MSSQLSERVER instance through SSMS, but I cannot connect to
either of the additional named instances (\INSTANCE01 or \INSTANCE02).
For example, if I try to connect to "sql.domain.com", I can successfully access the default instance on the remote server. If I try to connect to "sql.domain.com\INSTANCE01", I get an error stating
"A network-related or instance-specific error occurred while establishing a connection to SQL Server".
HOWEVER - if I try to connect to "sql.domain.com\INSTANCE01, 49301" (where 49301 is the TCP Port for the TCP/IP Protocol for this SQL Server instance), I am able to successfully connect.
This leads me to think that there's a communication issue with the SQL Server Browser service running on the remote SQL Server and my workstation.
The following items have been verified:
SQL Server Browser is running on the remote SQL Server
Windows Firewall has been disabled on the SQL Server
TCP Ports 1433, 1434, 1954, and 49301 have been opened up on the remote destination's firewall
UDP Port 1434 has been opened up on the remote destination's firewall
Thoughts? Did I miss something?

Hi brgnewman,
Use computername\instancename to connect to the database engine. Please try again. I think the configuration is OK.
Refer to Connecting from Another Computer:
http://msdn.microsoft.com/en-us/library/ms345343.aspx.
Thanks.
Maggie Luo
TechNet Community Support

Cannot connect to Remote SQL server

Hi,
I was able to connect to remote server before and it was working but since couple of days when I tried to connect it generates error.
"The Target PrincipalCannot name is incorrect.Cannot Generate SSPI context."
Jibran Ishtiaq

See
[ForumFAQ]How to troubleshoot error "SSPI handshake
failed with error code 0x80090324
A simple reason can be, that your local clock differens more then 5 min from the Server clock.
Olaf Helper
[ Blog] [ Xing] [ MVP]

Cannot connect to remote servers or exchange email?

Similar Messages

Maybe you are looking for