Change output pins to input pins on Keil MCB2300

I have a Keil MCB2300 setup and successfully running w/ LV2010. I want to know how do I change the digital pins from outputs to inputs. LabVIEW defaults to 7 outputs and 1 input, but surely I can chan;ge these. The Keil schematics just label the pins as digital w/out designating input or output.
thanks,
jason
Attachments:
ss1.PNG ‏37 KB
ss2.PNG ‏243 KB

Jason,
I found a document that I think may be helpful in configuring your inputs/outputs. It details how to create new I/O items for ARM targets which is what I believe the Keil MCB2300 is. Try following the steps in this document.
http://zone.ni.com/reference/en-XX/help/372459C-01/lvarmhelp/arm_eio_creating/
Regards,
-Nick-
Nick C | Staff LabVIEW Platform Product Support Engineer | National Instruments

Similar Messages

  • How can we change output pin for counter in X series daq

    hello every one...
    If this question is repeated then forgive me and direct me to that.
    I am using X series DAQ USB-6343. In specific instant i want counter output at specific pin and then agian for other requirement i want it to other pin. plz so me some path. i try to find thing but i was not luck...
    thanks & regards,
    Solved!
    Go to Solution.

    Attached is my example (it provides both methods discussed).  I used a text panel with the same device to count edges on PFI0.  Methodology:
    1) Run Example and export to PFI0.
    2) Stop Example
    3) Change output terminal to PFI1
    4) Run Example
    Notes:
    For Method 1, I would continue to see counts until I stopped and started the test panel.  Without digging it to deeply it appears as though the route is not released until the edge count timer is stopped.  Stopping and starting this counter stopped the counter from seeing edges on PFI0.
    For Method 2, I stopped seeing edges immediately after stopping the CO Pulse Freq task.
    Hope that helps,
    Dan
    Attachments:
    DiffCounterOPModified.vi ‏23 KB

  • I have the 2.5GHz i5 macbook pro that came out in june of 2012, i updated to OSX version 10.8.1 and now i am unable to change the 3.5mm headphone output into an input.

    i have the 2.5GHz i5 macbook pro that came out in june of 2012, i updated to OSX version 10.8.1 and now i am unable to change the 3.5mm headphone output into an input.

    i have the 2.5GHz i5 macbook pro that came out in june of 2012, i updated to OSX version 10.8.1 and now i am unable to change the 3.5mm headphone output into an input.

  • Is there a way to change the pin color in iPhoto so I can pin my photos  and places from those from others.  i think it would be cool to see where my friends have also been but not mix it with mine.  Thanks

    s there a way to change the pin color in iPhoto so I can pin my photos  and places from those from others.  i think it would be cool to see where my friends have also been but not mix it with mine.  Thanks

    No
    Suggest to Apple
    You can make a smart album based on camera to seperate photos
    LN

  • How do I change my Pin for Scan-To-Email from ePrintcenter on the HP 7520 Photosmart?

    Upon enterinng your email initially, you are sent a randomly generated 4 digit pin code for all your scan to email thereafter.
    Is there anyway you can manage this account and change the pin?
    I want to change it to something more easily remembered.
    I have registered and logged into eprint on the HP website, but that only allows me to create posts here and add my printer to my account and change the eprint email of the printer. There is no option to link my eprintcenter account and/or change my pin number.

    Hi djlongy,
    I am sorry at this time you cannot change your scan to email pin number.  I like your idea it would be a nice option to have.
    Hope this helps.

  • Counter Output Pin on PCI-6229

    I am using NI-DAQmx 7.3 C API with (among others) a PCI-6229.
    I have used DAQmxSetCOPulseTerm() to connect a counter output to a terminal other than the default. It seems to work- the output pulses do, in fact, appear at PFI 6 (the terminal I'm using for testing). But the pulses continue to appear at the default output pin as well.
    Is that expected?
    In order to reverse the situation, I used DAQmxResetCOPulseTerm() just before calling DAQmxClearTask(). The function returns zero, but if I subsequently make a new task to do pulse output from the same counter, pulses appear at both PFI 6 and at the default pin.
    Am I missing something?
    John Weeks
    WaveMetrics, Inc.
    Phone (503) 620-3001
    Fax (503) 620-6754
    www.wavemetrics.com

    Salvador Santolucito wrote:
    Hi John,
    I would suggest using the DAQmxTristateOutputTerminal. I have tried what you are doing in LabVIEW and I'm seeing the exact same results. When I set the default pin to tristate, the counter output does not show up on it.
    -Sal
    Thanks for trying it and confirming what I saw, and thanks for the pointer to DAQmxTristateOutputTerminal.
    John Weeks
    WaveMetrics, Inc.
    Phone (503) 620-3001
    Fax (503) 620-6754
    www.wavemetrics.com

  • Change/Deactivate pin screen

    I am getting an all white screen with the following text: CHANGE/DEACTIVATE PIN CHANGE PARENTAL CONTROL PINDEACTIVATE PARENTAL CONTROLCANCEL Whenever I select one option, the screen goes dark and I have to reset the entire process.

    jrfinger wrote:
    I am getting an all white screen with the following text:
    CHANGE/DEACTIVATE PIN
    CHANGE PARENTAL CONTROL PIN
    DEACTIVATE PARENTAL CONTROL
    CANCEL
    Whenever I select one option, the screen goes dark and I have to reset the entire process.
    Apologies for the issue and the experience that you described above. I have asked a colleague to review your account and reach out to you so that we can get any underlying issues identified and resolved.
    Thanks for your patience.

  • Generate a 12 bit digital output at DAQ output pin

    Hi 
      I have only a little knowledge in Labview
     I want to generate a 12 bit digital output at DAQ output pin , from a decimal number. I am using NI USB 6009
     Thanks in advance
      regards DK

    It seems to me that the same question was asked, answered, and marked as solved.
    http://forums.ni.com/t5/LabVIEW/Binary-output-at-t​he-digital-output-pin-as-1111-1111-1111/m-p/249969​...

  • How to Change my pin code

    How to Change my pin code

    Settings > General > Touch ID & Passcode.  Enter your current passcode, tap "Change Password, follow the prompts.

  • Hello, I would like to produce 2 different pulse trains on the CTRo and CTR1 output pins.

    (DAQ-CARD E6024 PCMCIA)I have the 2 output pins monitored on my scope, when CTR0 puts out a pulse train, CTR1 goes high. When CTR1 puts out a pulse train CTR0 goes high. Also, the pulses are interleaved with each other. Is there a way to make then start at the same time
    Attachments:
    Stim_Output_pulses_CTR_0,1.vi ‏94 KB

    Hello Zoltan,
    I would suggest using the counter gates to synchronize the counters. You will need to externally run a wire from one of the DIO lines you're not using to one of the counters' gates. When the counter gate is high, the pulse train will be generated on each counter. Both counters will need to use the same PFI line as the gate.
    There is an example program that ships with LabVIEW 7 called "Gen Dig Pulse Train-Continuous-Pause Trigger" for DAQmx. This demonstrates how to configure the counter to only generate the pulse train when the gate is high.
    With this configuration, you could synchronize the counters by writing to the DIO line which is wired to one of the counter gates when you're ready to start the pulse train generation.
    Hope t
    his helps.
    Kristi Hummel
    Applications Engineer
    National Instruments

  • I changed my pin code on my phone and forgotten it, how do I get in to my phone

    I changed my pin code on my phone last night and have  forgotten it. How do I get back into my phone or change it?

    You'll have to restore it as new using the computer/itunes you normally use.

  • Changing the pin code

    how do I change my PIN code?
    No need to reply just to say it's not safe, I might forget it and all that.

    Hi Rushafs ji,
    I supposed you meant the SIM pin code. I'm assuming that its a S60 OS. If so, you should be able to do it at Menu, Tools, Settings, Security, Phone and SIM, PIN code. Mobile lock code would be Lock code instead of PIN code.
    Hope this helps.
    Cheers.

  • Change bbm pin

    Hi
    Is it possible to switch bbm pin between two bb phones ? And how ?

    Hello Wqattan,
    You will not be able to change BBM Pins as each manufactured Blackberry Device has it's own unique PIN. It is like a serial number to any device.
    Cheers,
    Matthew Tobias

  • Change screen output to HDMI input

    I have inserted a HDMI cable into my laptop, and wish to use my laptop screen to display the content of the device on the other end of the HDMI cable. How can I do this?

    Unfortunately, this isn't possible, as the HDMI connector on your laptop is an output, not an input.

  • "change output" feature in output type configuration

    Hi
      I am trying to find a way of automatically triggering repeat output on change of delivery date in order.
       In output type configuration-general data there is a are for change output the F1 helps reada like this "..........The routine in the program checks which changes should result in a changed output being sent. ......"
       If anybody has worked on this functionality, please help me by giving any relevant input.
    TIA

    Take a copy of output requirement 014 and change the code to make it work for your delivery date.  Output requirement 014 is provided in standard SAP for BV - cash sales.  In cash sales, if the net value is changed, the output is automatically retriggered.
    Remember the KOMKBV1 in the below code represents the sales orders communication structure. If you are doing this requirement for delivery document use KOMKBV2 and for billing document output determination use KOMKBV3.
    ***INCLUDE LV61B014 .
          FORM KOBED_014                                                *
    Requirement to create an new order confirmation / invoice when     *
    the net value is changed.                                          *
    FORM KOBED_014.
      SY-SUBRC = 4.
    If the net value has changed, resend the Output type RD03
      IF KOMKBV1-NETWR NE *KOMKBV1-NETWR OR
         *KOMKBV1-NETWR IS INITIAL.
        SY-SUBRC = 0.
      ENDIF.
    ENDFORM.
          FORM KOBEV_014                                                *
          Reference to KOBED_014                                        *
    FORM KOBEV_014.
       PERFORM KOBED_014.
    ENDFORM.
    Thanks
    Kapil Sharma

Maybe you are looking for

  • How to run labview program in debugging mode in windows 95 version

    Respected all, I am facing probelm while running probe.vi. I received this command "connection to acquisition board was not found" when i run labview program. I  am using labview 5.1, fieldpoint FP 1000, NI-DAQ 6.5, Field point explorer version 1.6, 

  • Back up arrow key shows only in gray and won't let me go backwards

    IF I am reading a screen and I want to go back a screen the program will no longer give me a black arrow to go back. It will only show in gray and not work. Did I change a setting that is causing this? Does it have anything to do with my history? I c

  • Mm inventory mm reference material

    sir, i want to know which is the best book for sap mm inventory managment which will guide me throughly with the configration. thankyou

  • Reporting planning/actual figures for Expenses (Cost center wise)

    Hi, We have uploaded Planning for Costcenters for few accounts, which we want  to seen through F.01 in trial balance format. Where we can see planning figures for profit center as well as cost centers for given Financial Statement Version (FSV) Actua

  • IPhone is stuck in "DFU"??

    I passed my iPhone 4 to my friend because he "needed 3G network while he was away" and he came back saying that my phone is in dfu mode and that he cannot take it off of it. The iphone is really weird, its a black screen and no touch screen working.