Cisco Air LAP-1042 issue

Hi guys. I just purchase Cisco LAP-1042N for my office network expansion. When i console into the AP via serial. I am not able to used "configure terminal" command to set my AP name,static IP address.
I tried using "debug lwapp console cli" command it did not work. below is the capture screen of the error i am getting when assigning AP hostname. Error message : command is disable.
can some one guide me on how to configure the AP correctly and enable conf t command
Thanks in advanced.
Br
Syafiq

Is the AP new or used? It may have a configuration on it already if used - resest it to default and do the express setup as described here. I beleive the 1040 series needs a DHCP server per the following section from the configuraiton guide:
Default IP Address Behavior
When you connect a 1040, 1130AG, 1140, 1200, 1240, 1250, 1260, 2600 access point, or 1300 series access point/bridge with a default configuration to your LAN, the access point requests an IP address from your DHCP server and, if it does not receive an address, continues to send requests indefinitely.
As a Lightweight AP, most of its settings should come from the WLC once you have the LAP on the network where it can see the WLC.

Similar Messages

  • Cisco AIR-LAP 1131 reboot in loop

    Hi Everyone
    I recently had to deploy about 4 cisco 1131 AP's to one of our branch location. When configuring them on the controller, i needed to put them in HREAP mode. As soon as i do that and the AP needs to reboot, it will continue to reboot in a loop and indicate the following:
    Unexpected exception to CPUvector 1100, PC = 5A9048
    -Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
    Exception (1100)! Data TLB Miss
    SRR0 = 0x005A9048  SRR1 = 0x00029230  SRR2 = 0x0028007C  SRR3 = 0x00021230
    ESR = 0x00000000  DEAR = 0x025BFB94  TSR = 0x84000000  DBSR = 0x00000000
    CPU Register Context:
    Vector = 0x00001100  PC = 0x005A9048  MSR = 0x00029230  CR = 0x53000035
    LR = 0x0048A8A0  CTR = 0x00000072  XER = 0xA0000040
    R0 = 0x00000072  R1 = 0x00CD9790  R2 = 0x00000000  R3 = 0x025CBFF8
    R4 = 0x025BFB94  R5 = 0x00000000  R6 = 0x00000001  R7 = 0x000000C3
    R8 = 0x000001C8  R9 = 0x00000000  R10 = 0x025CBFF8  R11 = 0x00000000
    R12 = 0x00CDB580  R13 = 0x00000000  R14 = 0x00000000  R15 = 0x00000000
    R16 = 0x0184C8AA  R17 = 0x0184C71B  R18 = 0x00CDB760  R19 = 0x00000007
    R20 = 0x00000001  R21 = 0x00000000  R22 = 0x00000007  R23 = 0x00000001
    R24 = 0x0093BA68  R25 = 0x00000000  R26 = 0x00000001  R27 = 0x00000001
    R28 = 0x00001FA8  R29 = 0x0094A200  R30 = 0x01C7FE38  R31 = 0x00003D80
    Stack trace:
    PC = 0x005A9048, SP = 0x00CD9790
    Frame 00: SP = 0x00CD97D0    PC = 0x0048A6A8
    Frame 01: SP = 0x00CDB728    PC = 0x004361FC
    Frame 02: SP = 0x00CDB740    PC = 0x0042E078
    Frame 03: SP = 0x00CDB758    PC = 0x0044880C
    Frame 04: SP = 0x00CDB798    PC = 0x0042A280
    Frame 05: SP = 0x00CDB7C0    PC = 0x0042AA68
    Frame 06: SP = 0x00000000    PC = 0x0018A990
    Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by Cisco Systems, Inc.
    Compiled Fri 10-Aug-07 20:44 by kehsiao
    St-John-AP1 uptime is 1 minute,
    cisco AIR-LAP1131G-A-K9    (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
    Processor board ID FTX1632N00D
    PowerPCElvis CPU at 262Mhz, revision number 0x0950
    And this is all it does, and keep loading the image. I already know the recovery procedure to reset it, but i wanted to know how i can put these AP in HREAP without having these issues. In the setup we need, we cannot have those AP be in local mode.
    Thanks for any help and consideration .
    Regards

    Hi Scott
    Thanks for replying
    here is the full output between loops :
    Press RETURN to get started!
    *Mar  1 00:00:06.552: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:07.962: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:09.281: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by Cisco Systems, Inc.
    Compiled Fri 10-Aug-07 20:44 by kehsiao
    *Mar  1 00:00:09.281: %SNMP-5-COLDSTART: SNMP agent on host St-John-AP1 is undergoing a cold start
    *Mar  1 00:00:09.303: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:00:10.027: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
    *Mar  1 00:00:10.303: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:11.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
    *Mar  1 00:00:28.301: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
    *Mar  1 00:00:28.301: bsnInitRcbSlot: slot 1 has NO radio
    *Mar  1 00:00:28.323: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
    *Mar  1 00:00:29.049: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Mar  1 00:00:29.087: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:29.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:37.564: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.1.3.48, mask 255.255.0.0, hostname St-John-AP1
    Translating "CISCO-LWAPP-CONTROLLER.aimfire.net"...domain server (10.1.10.100) [OK]
    *Mar  1 00:00:50.821: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
    *Mar  1 00:00:50.822: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *Mar  1 15:49:20.913: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 15:49:21.306: %LWAPP-5-CHANGED: LWAPP changed state to CFG
    *Mar  1 15:49:21.351: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
    *Mar  1 15:52:11.000: %LWAPP-5-CHANGED: LWAPP changed sta
    15:52:12 UTC Fri Mar 1 2013: Unexpected exception to CPUvector 1100, PC = 0x5A9048  , LR = 0x48A8A0
    -Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
    CPU Register Context:
    MSR = 0x00029230  CR  = 0x53000035  CTR = 0x00000072  XER   = 0xA0000040
    R0  = 0x00000072  R1  = 0x00D1EC18  R2  = 0x00000000  R3    = 0x025CBFF8
    R4  = 0x025BFB94  R5  = 0x00000000  R6  = 0x00000001  R7    = 0x000000CA
    R8  = 0x000001C8  R9  = 0x00000000  R10 = 0x025CBFF8  R11   = 0x00000000
    R12 = 0x00D20A08  R13 = 0x00000000  R14 = 0x00000000  R15   = 0x00000000
    R16 = 0x01851A6A  R17 = 0x018518DB  R18 = 0x00D20BE8  R19   = 0x00000007
    R20 = 0x00000001  R21 = 0x00000000  R22 = 0x00000007  R23   = 0x00000001
    R24 = 0x0093BA68  R25 = 0x00000000  R26 = 0x00000001  R27   = 0x00000001
    R28 = 0x00001FA8  R29 = 0x0094A200  R30 = 0x01C7FE38  R31   = 0x00003D80
    Writing crashinfo to flash:/crashinfo_20130301-155213
    === Flushing messages (15:52:20 UTC Fri Mar 1 2013) ===
    Buffered messages:
    *Mar  1 00:00:06.552: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:07.962: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:09.281: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by Cisco Systems, Inc.
    Compiled Fri 10-Aug-07 20:44 by kehsiao
    *Mar  1 00:00:09.281: %SNMP-5-COLDSTART: SNMP agent on host St-John-AP1 is undergoing a cold start
    *Mar  1 00:00:09.303: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:00:10.027: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
    *Mar  1 00:00:10.303: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:11.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
    *Mar  1 00:00:28.301: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
    *Mar  1 00:00:28.301: bsnInitRcbSlot: slot 1 has NO radio
    *Mar  1 00:00:28.323: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
    *Mar  1 00:00:29.049: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Mar  1 00:00:29.087: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:29.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:37.564: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.1.3.48, mask 255.255.0.0, hostname St-John-AP1
    *Mar  1 00:00:50.821: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
    *Mar  1 00:00:50.822: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *Mar  1 15:49:20.913: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 15:49:21.306: %LWAPP-5-CHANGED: LWAPP changed state to CFG
    *Mar  1 15:49:21.351: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
    *Mar  1 15:52:11.000: %LWAPP-5-CHANGED: LWAPP changed state to UP
    *Mar  1 15:52:11.055: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    Queued messages:
    *Mar  1 15:52:23.534: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
    *Mar  1 15:52:11.414: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    Nested exception_rom_monitor call (2 times)
    Unexpected exception to CPUvector 1100, PC = 5A9048
    -Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
    Exception (1100)! Data TLB Miss
    SRR0 = 0x005A9048  SRR1 = 0x00029230  SRR2 = 0x0028007C  SRR3 = 0x00021230
    ESR = 0x00000000  DEAR = 0x025BFB94  TSR = 0x84000000  DBSR = 0x00000000
    CPU Register Context:
    Vector = 0x00001100  PC = 0x005A9048  MSR = 0x00029230  CR = 0x53000035
    LR = 0x0048A8A0  CTR = 0x00000072  XER = 0xA0000040
    R0 = 0x00000072  R1 = 0x00D1EC18  R2 = 0x00000000  R3 = 0x025CBFF8
    R4 = 0x025BFB94  R5 = 0x00000000  R6 = 0x00000001  R7 = 0x000000CA
    R8 = 0x000001C8  R9 = 0x00000000  R10 = 0x025CBFF8  R11 = 0x00000000
    R12 = 0x00D20A08  R13 = 0x00000000  R14 = 0x00000000  R15 = 0x00000000
    R16 = 0x01851A6A  R17 = 0x018518DB  R18 = 0x00D20BE8  R19 = 0x00000007
    R20 = 0x00000001  R21 = 0x00000000  R22 = 0x00000007  R23 = 0x00000001
    R24 = 0x0093BA68  R25 = 0x00000000  R26 = 0x00000001  R27 = 0x00000001
    R28 = 0x00001FA8  R29 = 0x0094A200  R30 = 0x01C7FE38  R31 = 0x00003D80
    Stack trace:
    PC = 0x005A9048, SP = 0x00D1EC18
    Frame 00: SP = 0x00D1EC58    PC = 0x0048A6A8
    Frame 01: SP = 0x00D20BB0    PC = 0x004361FC
    Frame 02: SP = 0x00D20BC8    PC = 0x0042E078
    Frame 03: SP = 0x00D20BE0    PC = 0x0044880C
    Frame 04: SP = 0x00D20C20    PC = 0x0042A280
    Frame 05: SP = 0x00D20C48    PC = 0x0042AA68
    Frame 06: SP = 0x00000000    PC = 0x0018A990
    Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by Cisco Systems, Inc.
    Compiled Fri 10-Aug-07 20:44 by kehsiao
    St-John-AP1 uptime is 1 minute, 7 seconds
    cisco AIR-LAP1131G-A-K9    (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
    Processor board ID FTX1632N00D
    PowerPCElvis CPU at 262Mhz, revision number 0x0950
    flashfs[0]: 40 files, 3 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 15998976
    flashfs[0]: Bytes used: 15129600
    flashfs[0]: Bytes available: 869376
    flashfs[0]: flashfs fsck took 41 seconds.
    Base ethernet MAC Address: d8:67:d9:ba:9f:2e
    Initializing ethernet port 0...
    Reset ethernet port 0...
    Reset done!
    ethernet link up, 100 mbps, full-duplex
    Ethernet port 0 initialized: link is up
    Loading "flash:/c1130-k9w8-mx.124-3g.JA2/c1130-k9w8-mx.124-3g.JA2"...###############################################
    File "flash:/c1130-k9w8-mx.124-3g.JA2/c1130-k9w8-mx.124-3g.JA2" uncompressed and installed, entry point: 0x3000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2007 by Cisco Systems, Inc.
    Compiled Fri 10-Aug-07 20:44 by kehsiao
    Image text-base: 0x00003000, data-base: 0x005AEE20
    Initializing flashfs...
    flashfs[1]: 40 files, 3 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 15998976
    flashfs[1]: Bytes used: 15129600
    flashfs[1]: Bytes available: 869376
    flashfs[1]: flashfs fsck took 5 seconds.
    flashfs[1]: Initialization complete....done Initializing flashfs.
    Radio 1 A506 7100 E8000000 A0000000 80000000 3
    Radio 0 0 0 0 0 0 2
    cisco AIR-LAP1131G-A-K9    (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
    Processor board ID FTX1632N00D
    PowerPCElvis CPU at 262Mhz, revision number 0x0950
    Last reset from unknown reload cause - reason ptr 0xF, PC 0x5A9048, address 0x0
    LWAPP image version 4.1.192.35
    1 FastEthernet interface
    1 802.11 Radio(s)
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: D8:67:D9:BA:9F:2E
    Part Number                          : 73-13304-02
    PCA Assembly Number                  : 800-36409-01
    PCA Revision Number                  : B0
    PCB Serial Number                    : FOC16304BZJ
    Top Assembly Part Number             : 800-29582-03
    Top Assembly Serial Number           : FTX1632N00D
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-LAP1131G-A-K9
    Press RETURN to get started!
    Also , the switchport is a trunk port, i can definitely try it an access port .

  • Cisco AIR-LAP 1522 PROBLEM

    Hello to everyone. They brought me a LAP1522 referring that it is not working properly. I am trying to connect to console port but the problem is that I only get log messages but I cannot edit something or type any commands. I have attached the log messages if you can catch something from there. Ignore the messages about not finding controller because the AP has been removed from the real network to my office.
    IOS Bootloader - Starting system.
    Xmodem file system is available.
    flashfs[0]: 18 files, 2 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31868928
    flashfs[0]: Bytes used: 15537664
    flashfs[0]: Bytes available: 16331264
    flashfs[0]: flashfs fsck took 23 seconds.
    Reading cookie from flash parameter block...done.
    Base Ethernet MAC address: 00:27:0c:27:3f:00
    Low Power PoE - enabling LAN Ethernet port only
    Loading "flash:/c1520-k9w8-mx.124-21a.JHB/c1520-k9w8-mx.124-21a.JHB"...###################################################################################################################################################################################################
    File "flash:/c1520-k9w8-mx.124-21a.JHB/c1520-k9w8-mx.124-21a.JHB" uncompressed and installed, entry point: 0x3000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C1520 Software (C1520-K9W8-M), Version 12.4(21a)JHB, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2010 by Cisco Systems, Inc.
    Compiled Tue 06-Jul-10 14:49 by prod_rel_team
    Proceeding with system init
    Proceeding to unmask interrupts
    Initializing flashfs...
    flashfs[1]: 18 files, 2 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 31352832
    flashfs[1]: Bytes used: 15537664
    flashfs[1]: Bytes available: 15815168
    flashfs[1]: flashfs fsck took 5 seconds.
    flashfs[1]: Initialization complete....done Initializing flashfs.
    Warning:  the compile-time code checksum does not appear to be present.
    Radio0  present A600 8000 A8020000 0 A8030000 30
    Radio1  present A600 8000 B8020000 0 B8030000 13
    Radio2 not present 0 0 0 0 0 11
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    %Error opening flash:/c1520-rcvk9w8-mx/info (No such file or directory)cisco AIR-LAP1522AG-E-K9   (PowerPC 8349) processor (revision A0) with 49142K/16384K bytes of memory.
    Processor board ID FCW1346W00Q
    PowerPC 8349 CPU at 533Mhz, revision number 0x0031
    Last reset from power loss
    LWAPP image version 6.0.199.0
    4 Gigabit Ethernet interfaces
    2 802.11 Radio(s)
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 00:27:0C:27:3F:00
    Part Number                          : 73-10918-04
    PCA Assembly Number                  : 800-28909-04
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC13430YBS
    Top Assembly Part Number             : 800-29338-04
    Top Assembly Serial Number           : FCW1346W00Q
    Top Revision Number                  : F0
    Product/Model Number                 : AIR-LAP1522AG-E-K9
    % Please define a domain-name first.
    flash:/mesh_start_cfg.txt: No such file or directoryThe filesystem containing the variables may not be initialized yet.
    Press RETURN to get started!
    Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:00:07.231: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:07.575: m8349_ether_enable: MACCFG1 sync timeout
    *Mar  1 00:00:08.079: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:08.579: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
    *Mar  1 00:00:08.655: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1297 messages)
    *Mar  1 00:00:08.683: AP identified to be in Huck Jr/1240/1130 configuration
    *Mar  1 00:00:09.615: %LINK-3-UPDOWN: Interface Ethernet4, changed state to up
    *Mar  1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet1, changed state to up
    *Mar  1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet2, changed state to up
    *Mar  1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet3, changed state to up
    *Mar  1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
    *Mar  1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down
    *Mar  1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2, changed state to down
    *Mar  1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3, changed state to down
    *Mar  1 00:00:10.695: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1520 Software (C1520-K9W8-M), Version 12.4(21a)JHB, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2010 by Cisco Systems, Inc.
    Compiled Tue 06-Jul-10 14:49 by prod_rel_team
    *Mar  1 00:00:10.695: %SNMP-5-COLDSTART: SNMP agent on host wifikal.Laiki-agora is undergoing a cold start
    *Mar  1 00:00:10.759: Warning: Failed to run startup script
    *Mar  1 00:00:10.771: %MESH-6-BVI_CREATED: Mesh BVI1 interface created
    *Mar  1 00:00:10.791: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:00:10.791: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:00:11.791: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:00:11.791: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:12.771: %LINK-3-UPDOWN: Interface BVI1, changed state to down
    *Mar  1 00:00:18.507: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4, changed state to up
    *Mar  1 00:00:20.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:00:22.787: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
    flash:/mesh_start_cfg.txt: No such file or directoryThe filesystem containing the variables may not be initialized yet.
    *Mar  1 00:00:25.771: No Mesh startup file found
    *Mar  1 00:00:29.763: Logging LWAPP message to 0.0.0.0.
    *Mar  1 00:00:31.787: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
    *Mar  1 00:00:31.787: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Mar  1 00:00:31.987: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:00:45.355: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASSIC_NO_INJECTOR_CONFIGURED WS-C2960-8TC-L (0025.b413.b802)
    *Mar  1 00:00:45.355:  -Verify the required power-injector is installed on this port: WS-C2960-8TC-L(Fas 0/2).
    *Mar  1 00:00:45.355:  -If a power-injector is installed, issue the command:"power inline negotiation injector installed"
    *Mar  1 00:01:26.015: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
    *Mar  1 00:01:34.515: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:01:36.515: %LINK-3-UPDOWN: Interface BVI1, changed state to up
    *Mar  1 00:01:37.515: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:01:39.563: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Mar  1 00:03:05.575: %LWAPP-3-FALLBACK_DHCP: Invalid Static Gateway, so fallback to DHCP.
    *Mar  1 00:03:15.583: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:03:15.703: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 20.20.20.37, mask 255.255.255.0, hostname wifikal.Laiki-agora
    *Mar  1 00:03:15.703: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:03:17.583: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
    *Mar  1 00:03:17.583: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message.
    *Mar  1 00:03:17.583: %CAPWAP-3-ERRORLOG: Failed to handle timer message.
    *Mar  1 00:03:17.583: %CAPWAP-3-ERRORLOG: Failed to process timer message.
    *Mar  1 00:03:17.583: %CAPWAP-3-ERRORLOG: Discovery interval timer expiry handler failed.
    Translating "CISCO-CAPWAP-CONTROLLER.TelestoHQ"...domain server (62.169.194.48)
    *Mar  1 00:03:20.751: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    Translating "CISCO-LWAPP-CONTROLLER.TelestoHQ"...domain server (62.169.194.48)
    *Mar  1 00:03:21.759: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Mar  1 00:03:21.815: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.TelestoHQ
    *Mar  1 00:03:21.871: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.TelestoHQ
    *Mar  1 00:04:37.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
    *Mar  1 00:04:37.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
    *Mar  1 00:04:37.583: %MESH-6-LINK_UPDOWN: Mesh station 0027.0c27.3ffc link Down

    Search this doc for "reset"
    http://www.cisco.com/en/US/docs/wireless/technology/mesh/design/guide/MeshAP_52.html
    Reset Button
    The access point has a reset button located on the bottom of the unit (see Figure 3). The reset button is recessed in a small hole that is sealed with a screw and a rubber gasket. The reset button is used to perform these functions:
    •Reset the access point—press the reset button for less than 10 seconds. LEDs turn off during the reset and then reactivate when the reset is complete.
    •Disable battery backup power—Press the reset button for more than 10 seconds. LEDs turn off, then on, and then stay off.
    –You can also disable the battery remotely by entering this command:
    config mesh battery-state disable AP_name
    •Switch off LEDS—Press the reset button for more than 10 seconds. LEDs turn off, then on, and then stay off.
    Figure 3 Reset Button Location
    1
    Reset button location
    Sent from Cisco Technical Support iPhone App

  • Cisco AIR -LAP-1142 status led continuosly blinking green

    hello all,
                I have implemented around 46 access points (AIR-LAP-1142) in a customer site and i can see that the led of some of the access points are continously blinking green and no clients are associated to these access points. I have a WISM which has two controllers in it. I can see the particular aps to be joined  in the controller. But my question is that why its not giving me any signal. Please help me as this is very urgent!!.. even if am under the access point the signal is not there. I checked the radio status of the aps and its up. The WLANs are activated from the controller also. Please help mee....!!

    continously blinking green
    This could mean that the AP hasn't joined the WiSM yet.
    Can you console into the AP?  If you can, reboot the AP and post the entire power up and bootup process and include the "sh logs".

  • Cisco Air-Lap1242AG

    Hi i was trying to create a better stronger wireless network at my house.  I picked up a Cisco Air-Lap1242AG on an auction thinking it would give me more range.   Now trying to set it up i am trying to figure out if i made a mistake?  Can this router be used at home with just a Cable Modem?  Or does this need to hook into a Business Network? 
    Thanks
    Eric

    A Cisco "Air-LAP" access point is useless standalone by itself. It must participate on a network with a Cisco
    Wireless Lan Controller appliance to configure and manage it.
    And it's just an access point, not a router too, like a typical home unit is. Looks like you bought the wrong tool for the job.
    In my opinion, the best performing consumer-grade wireless routers (for max range, and typical Internet surfing 802.11g speeds) I've ever encountered, for home use have been the old Buffalo Wireless-G High Power units, which I think you can still buy online these days.

  • Cisco AIR-ANT2410YR 2.4 GHz 10dBi antenna issue

    lahimakonem wrote:
    The AP is powered by the Ethernet cable . do you think that's the issue?If the AP and antenna are both powered from the same port, double check the power consumption specs and be sure the switch is capable of supplying enough juice.  You may need to run each device from its own PoE port... 2 cables instead of 1.

    Hello guys,
    I have a cisco antena ( name above) connected to a 1600 cisco air AP. Im in a newer building, no reighforced concrete walls or anything and i cannot get a signal when im more than 15 feet away... Is there any setting i need to change?
    Thank you
    This topic first appeared in the Spiceworks Community

  • Cisco AIR-CAP1602I-E-K9 Telnet issue

      Hi Team, I have installed new cisco AIR-CAP1602I-E-K9 in the remote site LAN however the access point received the ip address through central DHCP helper address. I am able to ping the access point through LAN but I am unable to telenet the device to configure.
    Also when Field enginner visited on site to connect physical he connected through console but we were not able get into configure mode though we had full privilege access.
    Please advice.    
    AP0006.f618.26f5#sh version
    Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2012 by Cisco Systems, Inc.
    Compiled Tue 11-Dec-12 04:52 by prod_rel_team
    ROM: Bootstrap program is C1600 boot loader
    BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
    AP0006.f618.26f5 uptime is 3 minutes
    System returned to ROM by power-on
    System image file is "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"
    Last reload reason:
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CAP1602I-E-K9    (PowerPC) processor (revision A0) with 98294K/32768K bytes of memory.
    Processor board ID FGL1703ZA3E
    PowerPC CPU at 533Mhz, revision number 0x2151
    Last reset from power-on
    LWAPP image version 7.4.1.37
    1 Gigabit Ethernet interface
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 00:06:F6:18:26:F5
    Part Number                          : 73-14671-04
    PCA Assembly Number                  : 000-00000-00
    PCA Revision Number                  :
    PCB Serial Number                    : FOC164971SY
    Top Assembly Part Number             : 800-38552-01
    Top Assembly Serial Number           : FGL1703ZA3E
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP1602I-E-K9
    Configuration register is 0xF

    Thanks,
    1. Does it mean I should not be able to telnet also into the AP though I can ping from Router LAN ( AP is connected directly to router ethernet interface).
    2. I am also not able to discover controller when running in controller-based IOS. getting below errors.
    Thanks to advice on above points.
    Mar  1 00:03:04.038: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
    *Mar  1 00:03:04.038: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:03:04.038: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:03:04.038: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Mar  1 00:03:04.038: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
    *Mar  1 00:03:04.042: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
    *Mar  1 00:03:04.042: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:03:04.042: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:03:04.042: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    AP0006.f618.26f5#
    *Mar  1 00:03:14.038: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
    *Mar  1 00:03:14.038: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:03:14.038: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:03:14.038: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Mar  1 00:03:14.038: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.1
    AP0006.f618.26f5#1.13
    *Mar  1 00:03:14.042: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
    *Mar  1 00:03:14.042: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:03:14.042: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:03:14.042: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Mar  1 00:03:24.029: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
    *Mar  1 00:03:24.029: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:03:24.029: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:03:24.033: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Mar  1 00:03:24.033: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
    *Mar  1 00:03:24.033: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
    *Mar  1 00:03:24.033: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:03:24.033: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:03:24.033: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Mar  1 00:03:34.041: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
    *Mar  1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:03:34.041: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Mar  1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
    *Mar  1 00:03:34.041: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
    *Mar  1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:03:34.041: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:03:34.041: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    Not in Bound state.
    *Mar  1 00:03:49.505: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
    *Mar  1 00:03:53.393: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
    *Mar  1 00:03:53.477: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.110.93.22, mask 255.255.255.128, hostname AP0006.f618.26f5
    en
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (10.50.1.235) (10.50.1.236)
    *Mar  1 00:04:00.505: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Mar  1 00:04:00.565: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
    *Mar  1 00:04:00.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
    *Mar  1 00:04:00.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:04:00.593: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:04:00.593: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Mar  1 00:04:00.593: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
    *Mar  1 00:04:00.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
    *Mar  1 00:04:00.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:04:10.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
    *Mar  1 00:04:10.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:04:10.593: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:04:10.593: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Mar  1 00:04:10.593: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
    *Mar  1 00:04:10.597: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
    *Mar  1 00:04:10.597: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:04:10.597: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:04:10.597: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Mar  1 00:04:20.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
    *Mar  1 00:04:20.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:04:20.593: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:04:20.593: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Mar  1 00:04:20.593: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
    *Mar  1 00:04:20.597: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
    *Mar  1 00:04:20.597: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:04:20.597: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:04:20.597: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Mar  1 00:04:30.593: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
    *Mar  1 00:04:30.593: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:04:30.593: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:04:30.593: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Mar  1 00:04:30.593: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 172.25.11.13
    *Mar  1 00:04:30.597: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_d6:f5:c0'running version 6.0.196.0 is rejected.
    *Mar  1 00:04:30.597: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:04:30.597: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:04:30.597: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    Not in Bound state.
    *Mar  1 00:04:46.069: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
    *Mar  1 00:04:49.161: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
    *Mar  1 00:04:49.273: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.110.115.20, mask 255.255.255.128, hostname AP0006.f618.26f5
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (10.50.1.235)
    *Mar  1 00:04:57.069: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP. (10.50.1.236)
    *Mar  1 00:05:15.068: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
    Not in Bound state.
    *Mar  1 00:06:00.568: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
    *Mar  1 00:06:04.396: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
    *Mar  1 00:06:04.412: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.110.93.22, mask 255.255.255.128, hostname AP0006.f618.26f5
    en
    AP0006.f618.26f5#
    AP0006.f618.26f5#sh
    Writing out the event log to flash:/event.log ...
    ip int
    *Mar  1 00:06:11.668: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reload Reason: Could not discover WLC using DHCP IP address, Reload to use static IP.

  • AIR-LAP-1142N-E-K9 unexpected power offs

    Hi we have two seperate Cisco wireless networks both based around the same infrastructure.
    Cisco 5508 WLC/s running 7.4.100 Firmware in our datacentre, with AIR-LAP-1142N-E-K9 LAPS distributed at site offices.
    This infrastructure has been running well until recently when we have had a spate of the LAPS appearing to power off.
    The LAP appears to be off with no LED status light as if it has been powered off, but the power supplies are still connected and the LAPS are often warm to the touch as if drawing power even when they have been "off" for a couple of days.
    Unplugging the power supply (at the LAP) and re-applying brings the LAP back on.
    The LAPS involved all used the recommended Cisco manufactured power supplies as there was no POE/power injector infrastructure.
    The LAPS vanish from the WLC as if disconnected, without any apparent errors in the WLC logs.
    There are no crash logs for the LAPS which have powered off.
    Console output from a LAP which has powered off on startup just shows the AP coming back from a "cold start".
    LAPS operate normally after restart, but after avariable period, typically 2-7 days will power off again.
    This is happening across multiple sites, to LAPS connected to different WLCs.
    Has anyone seen this issue before?

    The LAP appears to be off with no LED status light as if it has been powered off, but the power supplies are still connected and the LAPS are often warm to the touch as if drawing power even when they have been "off" for a couple of days.
    Gareth,
    Just want to make sure you are using a power brick/power injector.  Can you please confirm?
    Had issues with 7.4 when I noticed that some of my APs, running in PoE, would suddenly get "lost".  They would suddenly reboot and they wouldn't negotiate PoE properly.  I had to manually shut down the ports for at least 5 seconds.  If I don't leave it off for that long the APs simply won't boot up.
    Ever since I've moved to 7.5, I haven't seen this happen.
    There is a well-known bug, can't seem to find it, about 1140 and WLC firmware 7.4.  If I remembered correctly, the bug describes what you are seeing.
    You may want investigate in using 7.5.

  • Air-lap-1131-ag-e-k9 convert to autonomous not working

    Hi,
    i have a air-lap01131-ag-e-k9 that was originally in lightweight mode and configured with a controller, but i am in the process of wanting to convert to autonomous mode, i am having issues with connectivity to the AP from my laptop.
    i have followed numerous guides on this forum, i have successfully
    downloaded correct firmware
    renamed the firmware to .default
    placed this in root of tftp server folder
    connected laptop via console to view output
    connected laptop via Ethernet to Ethernet port of AP
    changed static ip on laptop to 10.0.0.2 set subnet mask to 255.255.255.0, default gateway to 10.0.0.1
    held reset button on AP when applying power and waiting for radio light to flash red
    AP gets a IP address then of 10.0.0.1
    But even though both laptop and AP are in the same subnet, i am unable to ping the AP from my laptop and it doesn't start the tftp process
    I have disabled firewall etc, and tried with both crossover and straight through cable, it seems there is something missing at this last stage, i even tried on a second laptop but that would not ping either, am i missing something.
    i acquired the AP for training purposes to help with studies and so far i have learnt a lot of troubleshooting but i would really love to get past this, any help would be really appreciated.
    Kind regards
    Sam

    Xmodem file system is available.
    flashfs[0]: 29 files, 9 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 15998976
    flashfs[0]: Bytes used: 7215616
    flashfs[0]: Bytes available: 8783360
    flashfs[0]: flashfs fsck took 31 seconds.
    Base ethernet MAC Address: 00:1e:f7:ed:b5:46
    Initializing ethernet port 0...
    Reset ethernet port 0...
    Reset done!
    ethernet link up, 100 mbps, full-duplex
    Ethernet port 0 initialized: link is up
    button pressed for 20 seconds
    process_config_recovery: set IP address and config to default 10.0.0.1
    process_config_recovery: image recovery
    image_recovery: Download default IOS tar image tftp://255.255.255.255/c1130-k9w7-tar.default
    examining image...
    %Error opening  (no such file or directory)Loading "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"...#########################################################################################################################################################################
    File "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by Cisco Systems, Inc.
    Compiled Mon 17-Jul-06 11:38 by alnguyen
    Image text-base: 0x00003000, data-base: 0x0035E440
    Initializing flashfs...
    flashfs[1]: 29 files, 9 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 15998976
    flashfs[1]: Bytes used: 7215616
    flashfs[1]: Bytes available: 8783360
    flashfs[1]: flashfs fsck took 4 seconds.
    flashfs[1]: Initialization complete....done Initializing flashfs.
    cisco AIR-LAP1131AG-E-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
    Processor board ID FCZ1222Q27A
    PowerPCElvis CPU at 262Mhz, revision number 0x0950
    Last reset from power-on
    LWAPP image version 3.0.51.0
    1 FastEthernet interface
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 00:1E:F7:ED:B5:46
    Part Number                          : 73-8962-12
    PCA Assembly Number                  : 800-24818-11
    PCA Revision Number                  : B0
    PCB Serial Number                    : FOC122106TU
    Top Assembly Part Number             : 800-29144-02
    Top Assembly Serial Number           : FCZ1222Q27A
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-LAP1131AG-E-K9
    Press RETURN to get started!
    *Mar  1 00:00:06.280: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
    *Mar  1 00:00:06.289: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2006 by Cisco Systems, Inc.
    Compiled Mon 17-Jul-06 11:38 by alnguyen
    *Mar  1 00:00:07.238: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
    *Mar  1 00:00:08.238: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
    *Mar  1 00:00:09.642: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
    *Mar  1 00:00:25.297: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
    *Mar  1 00:00:36.237: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up

  • CIsco AIR LAP1131AG E K9 Status LED = Yellow; Ethernet LED = Off; Radio LED = blinking Red, what is this? it isn't in the manual

    CIsco AIR LAP1131AG E K9 Status LED = Yellow; Ethernet LED = Off; Radio LED = blinking Red in a pattern, red off then red red, Our AP isn't working it won't show up on our Cisco WLC 2125 anymore and this is the LED indicators, I've checked in the manual and this combination of LEDs do not exists??

    No cisco web is working perfectly.
    do you have a valid CCO id with smarnet contract ?? then only you can download new IOS for AP:
    Autonomous AP image:
    http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=284180979&release=12.4.25d-JA2&relind=AVAILABLE&rellifecycle=ED&reltype=latest
    LAP AP image:
    http://software.cisco.com/download/release.html?mdfid=279537722&flowid=6775&softwareid=280775090&release=12.4.25e-JAP&relind=AVAILABLE&rellifecycle=ED&reltype=latest
    Regards

  • Is Cisco air-ap1230a a lightweight access point?

    Is Cisco air-ap1230a a lightweight access point? Can it be use for the new CCNP training?
    Thanks

    Hi Bao,
    The 1230 is not a Lightweight AP, but can be upgraded to LWAPP with the A Radio model listed below (Note that this model is EOS/EOL) this is probably not the best choice for your studies;
    Solution Requirements
    Migration from autonomous access point mode to lightweight mode is possible on these Cisco Aironet access point platforms:
    All 1130AG access points
    All 1240 AG access points
    For all IOS-based 1200 series modular access point (1200/1220 Cisco IOS Software Upgrade, 1210 and **1230 AP**) platforms, it depends on the radio:
    if 802.11G, MP21G and MP31G are supported
    if 802.11A, RM21A and RM22A are supported
    The 1200 series access points can be upgraded with any combination of supported radios: G only, A only, or both G and A.
    All 1310 AG access points
    From this good doc;
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html
    Cisco Aironet 1200 Series Access Point Ordering Guide
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00800c9435.html
    EOS & EOL for the Cisco Aironet 1200 Series 802.11a Access Points
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_eol_notice0900aecd801e5303.html
    Understanding the Lightweight Access Point Protocol (LWAPP)
    http://www.cisco.com/en/US/netsol/ns340/ns394/ns348/ns337/networking_solutions_white_paper0900aecd802c18ee.shtml
    Lightweight Access Point FAQ
    http://www.cisco.com/en/US/products/ps6306/products_qanda_item09186a00806a4da3.shtml
    Lightweight AP (LAP) Registration to a Wireless LAN Controller (WLC)
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00806c9e51.shtml
    **You are probably better off with something like the LAP 1131. Have a look here;
    http://www.cisco.com/en/US/products/hw/wireless/products_category_buyers_guide.html#access_points
    Hope this helps! I noticed your other post regarding the WLC suggestions and have responded there as well :)
    Rob

  • AIR-LAP 1231G-A-K9

       I have a couple of questions: I have a 161 AP,s most of which are AIR-LAP 1231G-A-K9 two 4400 WLC.
    Some of these APs are using  AIR-ANT 1728 (2.4 GHz omidirectional 5.2 dBi)  and Mobile Mark OD9-240 (2-GHz omnidirectional  9 dBi) on the same access points. Some of my AP are PoE and some are using a power supply (at the AP) some are using both. Power level is set at 2 a radios are not enabled just the bg radios. I'm having issues: I need to tweak the APs (Power settings & Channel settings) so my clients (LXE VX6) can refresh faster.
    Any suggestions?
    PS I did'nt set this up. It was handed to me.              

    All of the enabled APs have thier A radios disabled.
    1231 don't have 802.11a radios.  You are using two type of antennaes (5 dBi and 9 dBi) in the SAME UNIT.
    The only way to determine if you have proper signal is to walk around with a laptop and sniff out the signal.  If you have signal strength of about 65 to 75 dBi then this is good.  If your signal being received by the laptop is higher than 80 dBi then this is one of your problems.
    Please check if all the data rates for 802.11b and 802.11g are enabled.
    You may want to propose to management to upgrade your WAPs as they are old.  If they want something cheap (supports only 802.11 a/b/g) and with external antennas then 1240 is your option.  If you want internal antenna 1130 is still in the market.
    If management want internal antenna and support 802.11 a/b/g/n then the cheapest model is the 1040.  The 1260 will support 802.11 a/b/g/n and requires antennas.

  • MacBook Air intermittently has issues connecting to websites when wireless shows connected to the internet. The pages show that I am offline, but I can ping Google DNS. Windows PC, iPhone and Android phone have no issue displaying the same web pages.

    MacBook Air intermittently has issues connecting to websites when wireless shows connected to the internet. The pages show that I am offline, but I can ping Google DNS. Windows PC, iPhone and Android phone have no issue displaying the same web pages.How do I solve this issue?

    Go step by step and test.
    1. Power off the router. Unplug it from the wall. Wait a while.
        Plug it back to the wall. Power the router on. Wait until all the lights are lit properly. It will take a while.
        Restart the computer.
        Start up in Safe Mode.
        http://support.apple.com/kb/PH14204
    2. Empty Caches
        Safari > Preference > Advanced
        Checkmark the box for "Show Develop menu in menu bar".
        Develop menu will appear in the Safari menu bar.
        Click Develop and select "Empty Caches" from the dropdown.
    3. Deselect Proxies if selected.
        System Preference > Network > Advanced  > Proxies Tab
        Under "Select Protocol", uncheck any box if selected.
        Click "OK" then  "Apply”.

  • Cisco AIR-CAP26021-A-K9 || Error opening tftp:// ... /ap3g2-k9w7-tar.default

    Hi everyone:
    I have a problem with two Cisco AIR AP's ... I have configured already eight of them (in lightweight mode), but those two send me the next error, right now.
    ap: %Error opening tftp://255.255.255.255/ap3g2-k9w7-tar.default (connection timed out)
    And when I boot to the AP, it says:
    %Error opening flash
    IOS Bootloader - Starting system.
    flash is writable
    FLASH CHIP:  Numonyx Mirrorbit (0089)
    Xmodem file system is available.
    flashfs[0]: 11 files, 2 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31997952
    flashfs[0]: Bytes used: 7245824
    flashfs[0]: Bytes available: 24752128
    flashfs[0]: flashfs fsck took 15 seconds.
    Reading cookie from SEEPROM
    Base Ethernet MAC address: c0:67:af:6f:31:25
    Ethernet speed is 100 Mb - FULL Duplex
    button is pressed, wait for button to be released...
    button pressed for 21 seconds
    process_config_recovery: set IP address and config to default 10.0.0.1
    process_config_recovery: image recovery
    image_recovery: Download default IOS tar image tftp://255.255.255.255/ap3g2-k9w7-tar.default
    examining image...
    DPAA Set for Independent Mode
    DPAA_INIT = 0x0
    %Error opening tftp://255.255.255.255/ap3g2-k9w7-tar.default (connection timed out)ap:
    ap:
    ap:
    IOS Bootloader - Starting system.
    flash is writable
    FLASH CHIP:  Numonyx Mirrorbit (0089)
    Xmodem file system is available.
    flashfs[0]: 10 files, 2 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31997952
    flashfs[0]: Bytes used: 7245824
    flashfs[0]: Bytes available: 24752128
    flashfs[0]: flashfs fsck took 14 seconds.
    Reading cookie from SEEPROM
    Base Ethernet MAC address: c0:67:af:6f:31:25
    Ethernet speed is 100 Mb - FULL Duplex
    Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx"...###########################
    File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx" uncompressed and installed, entry point: 0x2003000
    executing...
    Secondary Bootloader - Starting system.
    Xmodem file system is available.
    flashfs[0]: 10 files, 2 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31997952
    flashfs[0]: Bytes used: 7245824
    flashfs[0]: Bytes available: 24752128
    flashfs[0]: flashfs fsck took 7 seconds.
    Base Ethernet MAC address: c0:67:af:6f:31:25
    Boot CMD: 'boot  flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx'
    Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"...#####################
    File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx" uncompressed and installed, entry point: 0x2003000
    executing...
    Initializing flashfs...
    flashfs[2]: 10 files, 2 directories
    flashfs[2]: 0 orphaned files, 0 orphaned directories
    flashfs[2]: Total bytes: 31739904
    flashfs[2]: Bytes used: 7245824
    flashfs[2]: Bytes available: 24494080
    flashfs[2]: flashfs fsck took 8 seconds.
    flashfs[2]: Initialization complete.
    flashfs[3]: 0 files, 1 directories
    flashfs[3]: 0 orphaned files, 0 orphaned directories
    flashfs[3]: Total bytes: 11999232
    flashfs[3]: Bytes used: 1024
    flashfs[3]: Bytes available: 11998208
    flashfs[3]: flashfs fsck took 0 seconds.
    flashfs[3]: Initialization complete.
    Copying radio files from flash: to ram:
    %Error opening flash:/ap3g2-rcvk9w8-mx/E2.bin (No such file or directory)
    %Error opening flash:/ap3g2-rcvk9w8-mx/B2.bin (No such file or directory)
    %Error opening flash:/ap3g2-rcvk9w8-mx/V2.bin (No such file or directory)
    %Error opening flash:/ap3g2-rcvk9w8-mx/X2.bin (No such file or directory)
    %Error opening flash:/ap3g2-rcvk9w8-mx/Y2.bin (No such file or directory)
    Uncompressing radio files...
    File not found: flash:/ap3g2-rcvk9w8-mx/8004.img
    File not found: flash:/ap3g2-rcvk9w8-mx/E5.bin
    File not found: flash:/ap3g2-rcvk9w8-mx/B5.bin
    File not found: flash:/ap3g2-rcvk9w8-mx/V5.bin
    File not found: flash:/ap3g2-rcvk9w8-mx/X5.bin
    File not found: flash:/ap3g2-rcvk9w8-mx/Y5.bin
    ...done Initializing flashfs.
    Press RETURN to get started!
    *Mar  1 00:00:11.335: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
    *Mar  1 00:00:13.071: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:13.663: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C2600 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2013 by Cisco Systems, Inc.
    Compiled Tue 30-Jul-13 23:08 by prod_rel_team
    *Mar  1 00:00:13.795: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
    *Mar  1 00:00:13.795: %CAPWAP-3-ERRORLOG: Failed to load configuration from flash. Resetting to default config
    *Mar  1 00:00:13.799: %PARSER-4-BADCFG: Unexpected end of configuration file.
    lwapp_crypto_init: MIC Present and Parsed Successfully
    *Mar  1 00:00:14.751: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:16.467: DPAA Initialization Complete
    *Mar  1 00:00:16.467: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
    *Mar  1 00:00:16.915: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    no bridge-group 1 source-learning
                       ^
    % Invalid input detected at '^' marker.
    %Default route without gateway, if not a point-to-point interface, may impact performance
    *Mar  1 00:00:47.151: %CDP_PD-4-POWER_OK: All radios disabled - NEGOTIATED inline power source
    *Mar  1 00:00:49.515: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.44.221, mask 255.255.255.0, hostname APc067.af6f.3125
    Translating "CISCO-CAPWAP-CONTROLLER.asf.gob.mx"...domain server (10.1.1.2)
    *Mar  1 00:01:00.403: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Mar  1 00:01:00.451: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.asf.gob.mx
    The thing is, I've been applying the instruction:
    capwap ap controller ip address 10.4.13.2
    'cause I want them to communicate with a remote controller, and the past eight did it fine, but this two didn't.
    As for the things I've already tried, I have reset it's parameters to it's initial settings, I've tried to load a new IOS image, I've cleared the flash memory, but nothing works, it keeps communicating with the old controller.
    How can I fix this? (I mean, changing or adapting the AP to a lightweight AP)
    Thanks in advance

    Its fine to try to apply it from the console...but if you really want to clear the AP, you need to clear the nvram.  so if changing the primary from the GUI that the AP has joined didn't work, then try this:
    debug capwap console cli
    erase /all nvram
    Example:
    Entered the username and password
    debug capwap console cli
    erase /all nvram:
    [confirm]
    undebug all
    reload
    [confirm]
    Thanks,
    Scott
    Help out other by using the rating system and marking answered questions as "Answered"

  • CISCO AIR-AP1252AG-E-K9 is keep rebooting with no reason

    Hello
    I have an cisco AIR-AP1252AG-E-K9  and it reeboots randomly with no aparent reason
    this is the configuration
    aaa group server radius rad_eap
    server 10.10.1.2 auth-port 1645 acct-port 1646
    aaa group server radius rad_mac
    aaa group server radius rad_acct
    server 10.10.1.2 auth-port 1645 acct-port 1646
    aaa group server radius rad_admin
    aaa group server tacacs+ tac_admin
    aaa group server radius rad_pmip
    aaa group server radius dummy
    aaa authentication login eap_methods group rad_eap
    aaa authentication login mac_methods local
    aaa authorization exec default local
    aaa accounting network acct_methods start-stop group rad_acct
    aaa session-id common
    clock timezone +0200 2
    ip domain name diamant.local
    dot11 activity-timeout unknown default 32400
    dot11 activity-timeout client default 32400 maximum 32400
    dot11 activity-timeout repeater default 32400 maximum 32400
    dot11 activity-timeout workgroup-bridge default 32400 maximum 32400
    dot11 activity-timeout bridge default 32400 maximum 32400
    dot11 ssid cisco
       authentication open eap eap_methods
       authentication network-eap eap_methods
       authentication key-management wpa
       guest-mode
    dot11 ssid diamant4
       authentication open eap eap_methods
       authentication network-eap eap_methods
       authentication key-management wpa
       guest-mode
    dot11 arp-cache
    power inline negotiation prestandard source
    username root privilege 15 password 7 060506324F41
    username Cisco privilege 15 password 7 1047051613121F120D0A2D2E2862626C7A46
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    encryption mode ciphers aes-ccm
    ssid diamant4
    speed  basic-1.0 basic-2.0 basic-5.5 basic-11.0 basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
    channel width 40-above
    channel 2412
    station-role root
    payload-encapsulation dot1h
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface Dot11Radio1
    no ip address
    no ip route-cache
    encryption mode ciphers aes-ccm
    ssid cisco
    dfs band 1 3 block
    speed  basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
    channel width 40-above
    channel dfs
    station-role root
    payload-encapsulation dot1h
    world-mode legacy
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface GigabitEthernet0
    no ip address
    no ip route-cache
    duplex auto
    speed auto
    bridge-group 1
    no bridge-group 1 source-learning
    bridge-group 1 spanning-disabled
    interface BVI1
    ip address dhcp client-id GigabitEthernet0
    no ip route-cache
    ip http server
    no ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    ip radius source-interface BVI1
    logging history size 200
    no cdp run
    radius-server attribute 32 include-in-access-req format %h
    radius-server host 10.10.1.2 auth-port 1645 acct-port 1646 key 7 13011E13060D0A3E
    radius-server vsa send accounting
    bridge 1 route ip
    and the logs
    *Mar  1 00:00:06.207: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:07.035: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:07.543: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
    *Mar  1 02:00:09.599 +0200: %SYS-6-CLOCKUPDATE: System clock has been updated from 00:00:09 UTC Fri Mar 1 2002 to 02:00:09 +0200 Fri Mar 1 2002, configured from console by console.
    *Mar  1 02:00:09.755 +0200: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 02:00:09.763 +0200: %SYS-5-CONFIG_I: Configured from memory by console
    *Mar  1 02:00:09.767 +0200: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2009 by Cisco Systems, Inc.
    Compiled Sun 07-Jun-09 03:50 by prod_rel_team
    *Mar  1 02:00:09.767 +0200: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
    *Mar  1 20:39:11.027 +0200: %SSH-5-ENABLED: SSH 1.99 has been enabled
    *Mar  1 20:39:11.027 +0200: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 20:39:11.027 +0200: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 20:39:11.531 +0200: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 20:39:11.531 +0200: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 20:39:13.055 +0200: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 20:39:13.055 +0200: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 20:39:14.311 +0200: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
    *Mar  1 20:39:17.919 +0200: %DOT11-6-DFS_SCAN_START: DFS: Scanning frequency 5280 MHz for 60 seconds.
    *Mar  1 20:39:17.919 +0200: %DOT11-6-FREQ_USED: Interface Dot11Radio1, frequency 5280 selected
    *Mar  1 20:39:17.919 +0200: %DOT11-4-FREQ_CHANGED: Interface Dot11Radio1, channel or channel width changed: 40Mhz above not allowed on channel
    *Mar  1 20:39:17.923 +0200: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 20:39:17.931 +0200: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    Apr  6 12:05:00.537 +0200: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    Apr  6 12:05:00.537 +0200: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    Apr  6 12:05:00.709 +0200: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.10.1.243, mask 255.255.255.0, hostname ap
    Apr  6 12:05:32.729 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station PC186 5894.6b5d.6c00 Associated KEY_MGMT[WPAv2]
    Apr  6 12:05:34.325 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   687f.74fb.3b1f Associated KEY_MGMT[WPAv2]
    Apr  6 12:05:34.481 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   687f.74fb.305d Associated KEY_MGMT[WPAv2]
    Apr  6 12:05:35.117 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   0025.9cde.155a Associated KEY_MGMT[WPAv2]
    Apr  6 12:05:45.493 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station  687f.74fb.2fe0 Associated KEY_MGMT[WPAv2]
    Apr  6 12:05:59.545 +0200: %DOT11-6-DFS_SCAN_COMPLETE: DFS scan complete on frequency 5280 MHz
    Apr  6 12:06:06.561 +0200: %DOT11-6-ASSOC: Interface Dot11Radio1, Station  0025.9cf8.9149 Associated KEY_MGMT[WPAv2]
    Apr  6 12:06:56.471 +0200: %DOT11-6-ASSOC: Interface Dot11Radio1, Station   0025.9cde.0fc5 Associated KEY_MGMT[WPAv2]
    Apr  6 12:08:11.008 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 0025.9cde.155a Reason: Previous authentication no longer valid
    Apr  6 12:08:11.016 +0200: %DOT11-4-MAXRETRIES: Packet to client 0025.9cde.155a reached max retries, removing the client
    Apr  6 12:08:14.124 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   0025.9cde.155a Associated KEY_MGMT[WPAv2]
    Apr  6 12:08:17.608 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 0025.9cde.155a Reason: Previous authentication no longer valid
    Apr  6 12:08:48.950 +0200: %DOT11-7-AUTH_FAILED: Station 0025.9cde.155a Authentication failed
    Apr  6 12:08:48.950 +0200: %DOT11-4-MAXRETRIES: Packet to client 0025.9cde.155a reached max retries, removing the client
    Apr  6 12:09:12.978 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   0025.9cde.155a Associated KEY_MGMT[WPAv2]
    Apr  6 12:25:35.510 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.305d Reason: Sending station has left the BSS
    Apr  6 12:25:35.530 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   687f.74fb.305d Associated KEY_MGMT[WPAv2-CP]
    Apr  6 12:35:32.229 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.3b1f Reason: Sending station has left the BSS
    Apr  6 12:35:32.245 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   687f.74fb.3b1f Associated KEY_MGMT[WPAv2-CP]
    Apr  6 12:37:27.996 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.3b1f Reason: Sending station has left the BSS
    Apr  6 12:37:28.016 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   687f.74fb.3b1f Associated KEY_MGMT[WPAv2-CP]
    Apr  6 12:54:07.729 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.2fe0 Reason: Previous authentication no longer valid
    Apr  6 12:54:09.457 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station  687f.74fb.2fe0 Associated KEY_MGMT[WPAv2]
    Apr  6 12:54:36.236 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.2fe0 Reason: Previous authentication no longer valid
    Apr  6 10:54:56.515: Client 687f.74fb.2fe0 failed: reached maximum retries
    Apr  6 12:55:37.141 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station  687f.74fb.2fe0 Associated KEY_MGMT[WPAv2]
    Apr  6 13:30:07.002 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 5894.6b5d.6c00 Reason: Sending station has left the BSS
    Apr  6 13:30:17.442 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.3b1f Reason: Sending station has left the BSS
    Apr  6 13:30:17.802 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   687f.74fb.3b1f Associated KEY_MGMT[WPAv2-CP]
    Apr  6 13:34:59.087 +0200: %DOT11-4-MAXRETRIES: Packet to client 687f.74fb.3b1f reached max retries, removing the client
    Apr  6 13:34:59.087 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.3b1f Reason: Previous authentication no longer valid
    Apr  6 13:35:02.743 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   687f.74fb.3b1f Associated KEY_MGMT[WPAv2]
    Apr  6 13:35:23.451 +0200: %DOT11-4-MAXRETRIES: Packet to client 687f.74fb.3b1f reached max retries, removing the client
    Apr  6 13:35:23.455 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.3b1f Reason: Previous authentication no longer valid
    Apr  6 13:35:26.743 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   687f.74fb.3b1f Associated KEY_MGMT[WPAv2]
    Apr  6 13:36:40.768 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.3b1f Reason: Sending station has left the BSS
    Apr  6 13:38:59.004 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   687f.74fb.3b1f Associated KEY_MGMT[WPAv2]
    Apr  6 13:40:56.655 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.3b1f Reason: Sending station has left the BSS
    Apr  6 13:40:56.703 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   687f.74fb.3b1f Associated KEY_MGMT[WPAv2-CP]
    Apr  6 13:56:42.322 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 0025.9cf8.9149 Reason: Previous authentication no longer valid
    Apr  6 13:56:45.490 +0200: %DOT11-6-ASSOC: Interface Dot11Radio1, Station  0025.9cf8.9149 Associated KEY_MGMT[WPAv2]
    Apr  6 13:56:49.302 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 0025.9cf8.9149 Reason: Previous authentication no longer valid
    Apr  6 11:57:11.623: Client 0025.9cf8.9149 failed: reached maximum retries
    Apr  6 14:12:43.510 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.305d Reason: Sending station has left the BSS
    Apr  6 14:12:43.526 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   687f.74fb.305d Associated KEY_MGMT[WPAv2-CP]
    Apr  6 14:49:12.472 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.305d Reason: Previous authentication no longer valid
    Apr  6 14:49:15.628 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   687f.74fb.305d Associated KEY_MGMT[WPAv2]
    Apr  6 14:49:21.672 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.305d Reason: Previous authentication no longer valid
    Apr  6 14:49:53.282 +0200: %DOT11-7-AUTH_FAILED: Station 687f.74fb.305d Authentication failed
    Apr  6 14:49:53.282 +0200: %DOT11-4-MAXRETRIES: Packet to client 687f.74fb.305d reached max retries, removing the client
    Apr  6 14:52:04.097 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station PC186 5894.6b5d.6c00 Associated KEY_MGMT[WPAv2]
    Apr  6 15:14:29.682 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 0025.9cde.155a Reason: Previous authentication no longer valid
    Apr  6 15:15:03.124 +0200: %DOT11-7-AUTH_FAILED: Station 0025.9cde.155a Authentication failed
    Apr  6 15:15:03.124 +0200: %DOT11-4-MAXRETRIES: Packet to client 0025.9cde.155a reached max retries, removing the client
    Apr  6 15:21:02.660 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.3b1f Reason: Previous authentication no longer valid
    Apr  6 15:21:02.664 +0200: %DOT11-4-MAXRETRIES: Packet to client 687f.74fb.3b1f reached max retries, removing the client
    Apr  6 15:21:05.780 +0200: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   687f.74fb.3b1f Associated KEY_MGMT[WPAv2]
    Apr  6 15:21:09.808 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 687f.74fb.3b1f Reason: Previous authentication no longer valid
    Apr  6 15:21:41.058 +0200: %DOT11-7-AUTH_FAILED: Station 687f.74fb.3b1f Authentication failed
    Apr  6 15:21:41.058 +0200: %DOT11-4-MAXRETRIES: Packet to client 687f.74fb.3b1f reached max retries, removing the client
    Apr  6 15:24:36.911 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 0025.9cde.0fc5 Reason: Previous authentication no longer valid
    Apr  6 15:24:41.435 +0200: %DOT11-7-AUTH_FAILED: Station 0025.9cde.0fc5 Authentication failed
    Apr  6 15:24:45.131 +0200: %DOT11-6-ASSOC: Interface Dot11Radio1, Station   0025.9cde.0fc5 Associated KEY_MGMT[WPAv2]
    Apr  6 15:24:54.127 +0200: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 0025.9cde.0fc5 Reason: Previous authentication no longer valid
    Apr  6 15:25:27.623 +0200: %DOT11-7-AUTH_FAILED: Station 0025.9cde.0fc5 Authentication failed
    Apr  6 15:25:27.623 +0200: %DOT11-4-MAXRETRIES: Packet to client 0025.9cde.0fc5 reached max retries, removing the client

    i found something about how to reach the maximum N speed
    Factors that Affect 802.11n Throughput
    There are circumstances where 802.11n devices cannot operate at their  maximum capable data rates. There are various reasons why this occurs.  This is the list of factors that affect 802.11n throughput:
    When 802.11n clients operate in a mixed environment with 802.11a or  802.11 b/g clients, 802.11n provides a protection mechanism to  interoperate with 802.11a or 802.11 b/g clients. This introduces an  overhead and reduces the throughput of 802.11n devices. Maximum  throughput is achieved in Greenfield mode where only 802.11n clients exist.
    Factors such as Channel width, Guard Interval and Reduced IFS (RIFS) play a major role in the bandwidth. Table 1 and Table 2 show how these factors affect the bandwidth.
    Clients ability to send a Block Ack instead of individual frame acknowledgements.
    MCS Index configured on the WLC.
    Proximity to AP—Clients closer to the AP experience higher data  rates. As clients move farther away from the AP, signal strength  reduces. As a result, data rate decreases steadily.
    RF environment—Amount of noise and interference in the environment.  The less the noise and interference, the greater the bandwidth.
    Encryption/ Decryption—Encryption in general reduces the throughput  due to the overhead involved in the data encryption/decryption process.  However, advanced encryption standards, such as AES, can provide better  throughput when compared to other encryption standards, such as TKIP and  WEP.
    Wired Network Infrastructure—Bandwidth of the wired infrastructure  determines the speed of the traffic to and from the wired network to the  wireless clients.
    If using an AP1250, change the AP to H-REAP mode for a 5-10% boost.
    If using an AP1140, keep the AP in local mode and enable TCP MSS on the controller. Use the config ap tcp-adjust-mss enable all 1363 command in order to enable it.
    Disable RRM scanning to prevent any throughput drops when going off channel. This can yield a 1-3% improvement.
    Disable RLDP to ensure the AP does not attempt to connect to rogue devices during testing.
    Use a Wireless Controller 5508 as the data plane is superior to the 4404-series.
    My questions are:
    1. How i can i put the access point to operate only in N mode (because all my clients are N)
    2.The guard interval can be modify ?
    3. How to put my AP in H-REAP (can i do this without WLC?)
    4. How to disable RRM
    5.How to disable RLDP.
    Thank you.

Maybe you are looking for

  • Error when activating an R/3 generic datasource in BW

    Hi I've created a generic datasource in R/3 4.6C system using a table view over R/3 standard Project System tables with joins.  This datasource has been activated. I then replicated this generic datasource in BI7 datawarehousing environment.  The rep

  • Does Oracle DB have the utility to compute the CRC?

    Hi Pros, CRC stands for Cyclic redundancy check as we all know, there are ways of caculate it using programing language like Java, C#,etc, since we are undertake the ETL job for data warehouse, there are many update operation in DB using SQL, so I am

  • Automation of jobs

    Hi All I have a oracle database version--10.1.0.5.0 on Windows platform. I have scheduled Export and RMAN for every day. Now i want to get email notification on the above job completion. Can anyone have the script which he can share with me for this.

  • How to enlarge the tool bar and all fonts in the drop-downs using HDMI monitor due print is to small.

    I'm now using Win 7 and an HDMI monitor. The print and icons on the Firefox Toolbar, and the drop-downs is very small. How can I increase the font & Icon size on the Toolbar and all drop-downs? Thanks!

  • Trying to do a floating navigation

    I'm a new user experimenting with a one page design. I thought it would be nice to have a floating navigation on one side of browser that would point to the next anchor up or down for people like myself who don't like to scroll all the time! Now I'm