Client not recieiving ip address

I have a C857 wireless router and for some reason it has stopped sending my laptop an ip address nor can I see the wireless network when i browse for the network. If I connect to the router with a cable, I get an ip address from the DHCP setup. Does anyone know how I can troubleshoot the router for not broadcasting the network or why I cannot see the Wireless network?
Thanks

Can you try to debug the DHCP in 857 to check is there any wireless device to request the DHCP address ?
Moreover, is there any authentication setup in the wireless router ? If yes, there may be some issue stop the process before process to get an IP address.
Check below for basic config of DHCP in 85x router.
http://www.cisco.com/en/US/products/hw/routers/ps380/products_configuration_guide_chapter09186a008045d272.html#wp42306
Check more on the wireless interface config.
http://www.cisco.com/en/US/products/hw/routers/ps380/products_configuration_guide_chapter09186a008045d289.html#wp79536
Please post the config.
Hope this helps.

Similar Messages

  • Client not receive ip address - dhcp_reqd

    Hi,
    In my environment there's a  5508 (firmware 7.4.110.0) and ap 1600 with a ias radius server. All wlan are in flex-connect local switching, one client try to connect on a wlan but not receive ip address. After enabled debug aaa all i took the log corresponding :
    Cisco Controller) >*emWeb: Feb 11 16:52:36.047: Created WARP Capabilities IE (length 12) for WLAN LAB
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Adding mobile on LWAPP AP 00:3a:9a:77:55:a0(0)
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Association received from mobile on BSSID 00:3a:9a:77:55:06
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Rf profile 200 Clients are allowed to AP radio
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Max Client Trap Threshold: 50  cur: 3
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Rf profile 200 Clients are allowed to AP wlan
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 Re-applying interface policy for client
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_2: Feb 11 16:54:22.495: 18:3d:a2:25:01:a4 In processSsidIE:4264 setting Central switched to FALSE
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Applying site-specific Local Bridging override for station 18:3d:a2:25:01:a4 - vapId 103, site 'Test', interface 'management'
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Applying Local Bridging Interface Policy for station 18:3d:a2:25:01:a4 - vlan 0, interface id 0, interface 'management'
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Applying site-specific override for station 18:3d:a2:25:01:a4 - vapId 103, site 'Test', interface 'management'
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 0
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Re-applying interface policy for client
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2246)
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 STA - rates (8): 130 132 139 150 12 18 24 36 0 0 0 0 0 0 0 0
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Processing WPA IE type 221, length 24 for mobile 18:3d:a2:25:01:a4
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 Setting active key cache index 8 ---> 8
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 unsetting PmkIdValidatedByAp
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_2: Feb 11 16:54:22.496: 18:3d:a2:25:01:a4 0.0.0.0 8021X_REQD (3) DHCP required on AP 00:3a:9a:77:55:a0 vapId 103 apVapId 1for this client
    *apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 00:3a:9a:77:55:a0 vapId 103 apVapId 1 flex-acl-name:
    *apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 apfMsAssoStateInc
    *apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 apfPemAddUser2 (apf_policy.c:276) Changing state for mobile 18:3d:a2:25:01:a4 on AP 00:3a:9a:77:55:a0 from Idle to Associated
    *apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 apfPemAddUser2:session timeout forstation 18:3d:a2:25:01:a4 - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is  0
    *apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 Stopping deletion of Mobile Station: (callerId: 48)
    *apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
    *apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 Sending Assoc Response to station on BSSID 00:3a:9a:77:55:a0 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_2: Feb 11 16:54:22.497: 18:3d:a2:25:01:a4 apfProcessAssocReq (apf_80211.c:7399) Changing state for mobile 18:3d:a2:25:01:a4 on AP 00:3a:9a:77:55:a0 from Associated to Associated
    *apfMsConnTask_2: Feb 11 16:54:22.506: 18:3d:a2:25:01:a4 Updating AID for REAP AP Client 00:3a:9a:77:55:a0 - AID ===> 4
    *dot1xMsgTask: Feb 11 16:54:22.512: 18:3d:a2:25:01:a4 Station 18:3d:a2:25:01:a4 setting dot1x reauth timeout = 1800
    *dot1xMsgTask: Feb 11 16:54:22.512: 18:3d:a2:25:01:a4 dot1x - moving mobile 18:3d:a2:25:01:a4 into Connecting state
    *dot1xMsgTask: Feb 11 16:54:22.512: 18:3d:a2:25:01:a4 Sending EAP-Request/Identity to mobile 18:3d:a2:25:01:a4 (EAP Id 1)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.513: 18:3d:a2:25:01:a4 Received EAPOL START from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.513: 18:3d:a2:25:01:a4 dot1x - moving mobile 18:3d:a2:25:01:a4 into Connecting state
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.513: 18:3d:a2:25:01:a4 Sending EAP-Request/Identity to mobile 18:3d:a2:25:01:a4 (EAP Id 2)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.541: 18:3d:a2:25:01:a4 Received EAPOL EAPPKT from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.541: 18:3d:a2:25:01:a4 Received EAP Response packet with mismatching id (currentid=2, eapid=1) from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.554: 18:3d:a2:25:01:a4 Received EAPOL EAPPKT from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.554: 18:3d:a2:25:01:a4 Received Identity Response (count=2) from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.554: 18:3d:a2:25:01:a4 EAP State update from Connecting to Authenticating for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.554: 18:3d:a2:25:01:a4 dot1x - moving mobile 18:3d:a2:25:01:a4 into Authenticating state
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.554: 18:3d:a2:25:01:a4 Entering Backend Auth Response state for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.572: 18:3d:a2:25:01:a4 Processing Access-Challenge for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.572: 18:3d:a2:25:01:a4 Entering Backend Auth Req state (id=3) for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.572: 18:3d:a2:25:01:a4 Sending EAP Request from AAA to mobile 18:3d:a2:25:01:a4 (EAP Id 3)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.585: 18:3d:a2:25:01:a4 Received EAPOL EAPPKT from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.585: 18:3d:a2:25:01:a4 Received EAP Response from mobile 18:3d:a2:25:01:a4 (EAP Id 3, EAP Type 25)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.585: 18:3d:a2:25:01:a4 Entering Backend Auth Response state for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.598: 18:3d:a2:25:01:a4 Processing Access-Challenge for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.598: 18:3d:a2:25:01:a4 Entering Backend Auth Req state (id=4) for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.598: 18:3d:a2:25:01:a4 Sending EAP Request from AAA to mobile 18:3d:a2:25:01:a4 (EAP Id 4)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.613: 18:3d:a2:25:01:a4 Received EAPOL EAPPKT from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.613: 18:3d:a2:25:01:a4 Received EAP Response from mobile 18:3d:a2:25:01:a4 (EAP Id 4, EAP Type 25)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.613: 18:3d:a2:25:01:a4 Entering Backend Auth Response state for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.627: 18:3d:a2:25:01:a4 Processing Access-Challenge for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.627: 18:3d:a2:25:01:a4 Entering Backend Auth Req state (id=7) for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.627: 18:3d:a2:25:01:a4 WARNING: updated EAP-Identifier 4 ===> 7 for STA 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.627: 18:3d:a2:25:01:a4 Sending EAP Request from AAA to mobile 18:3d:a2:25:01:a4 (EAP Id 7)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.643: 18:3d:a2:25:01:a4 Received EAPOL EAPPKT from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.643: 18:3d:a2:25:01:a4 Received EAP Response from mobile 18:3d:a2:25:01:a4 (EAP Id 7, EAP Type 25)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.643: 18:3d:a2:25:01:a4 Entering Backend Auth Response state for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Processing Access-Accept for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Resetting web IPv4 acl from 255 to 255
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Resetting web IPv4 Flex acl from 65535 to 65535
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Setting re-auth timeout to 1800 seconds, got from WLAN config.
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Station 18:3d:a2:25:01:a4 setting dot1x reauth timeout = 1800
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Username entry (pippo) created for mobile, length = 253
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Username entry (pippo) created in mscb for mobile, length = 253
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Creating a PKC PMKID Cache entry for station 18:3d:a2:25:01:a4 (RSN 0)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.656: 18:3d:a2:25:01:a4 Sending EAP-Success to mobile 18:3d:a2:25:01:a4 (EAP Id 7)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.657: 18:3d:a2:25:01:a4 Freeing AAACB from Dot1xCB as AAA auth is done for  mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.657: 18:3d:a2:25:01:a4 Starting key exchange to mobile 18:3d:a2:25:01:a4, data packets will be dropped
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.657: 18:3d:a2:25:01:a4 Sending EAPOL-Key Message to mobile 18:3d:a2:25:01:a4
                                                                                                                        state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.657: 18:3d:a2:25:01:a4 Entering Backend Auth Success state (id=7) for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.657: 18:3d:a2:25:01:a4 Received Auth Success while in Authenticating state for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.657: 18:3d:a2:25:01:a4 dot1x - moving mobile 18:3d:a2:25:01:a4 into Authenticated state
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.671: 18:3d:a2:25:01:a4 Received EAPOL-Key from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.671: 18:3d:a2:25:01:a4 Received EAPOL-key in PTK_START state (message 2) from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.671: 18:3d:a2:25:01:a4 Stopping retransmission timer for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.671: 18:3d:a2:25:01:a4 Sending EAPOL-Key Message to mobile 18:3d:a2:25:01:a4
                                                                                                                        state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 Received EAPOL-Key from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 Stopping retransmission timer for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 apfMs1xStateInc
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 0.0.0.0 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state 8021X_REQD (3)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 0.0.0.0 L2AUTHCOMPLETE (4) DHCP required on AP 00:3a:9a:77:55:a0 vapId 103 apVapId 1for this client
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.689: 18:3d:a2:25:01:a4 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 00:3a:9a:77:55:a0 vapId 103 apVapId 1 flex-acl-name:
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5952, Adding TMP rule
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 00:3a:9a:77:55:a0, slot 0, interface = 13, QOS = 0
      IPv4 ACL ID = 255, IP
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206  Local Bridging Vlan = 0, Local Bridging intf id = 0
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 Key exchange done, data packets from mobile 18:3d:a2:25:01:a4 should be forwarded shortly
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 Sending EAPOL-Key Message to mobile 18:3d:a2:25:01:a4
                                                                                                                        state PTKINITDONE (message 5 - group), replay counter 00.00.00.00.00.00.00.02
    *pemReceiveTask: Feb 11 16:54:22.690: 18:3d:a2:25:01:a4 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    *spamApTask3: Feb 11 16:54:22.707: 18:3d:a2:25:01:a4 Sent EAPOL-Key M5 for mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.768: 18:3d:a2:25:01:a4 Received EAPOL-Key from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.768: 18:3d:a2:25:01:a4 Received EAPOL-key in REKEYNEGOTIATING state (message 6) from mobile 18:3d:a2:25:01:a4
    *Dot1x_NW_MsgTask_4: Feb 11 16:54:22.769: 18:3d:a2:25:01:a4 Stopping retransmission timer for mobile 18:3d:a2:25:01:a4
    *apfReceiveTask: Feb 11 16:54:25.619: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
    *apfReceiveTask: Feb 11 16:54:25.619: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5576, Adding TMP rule
    *apfReceiveTask: Feb 11 16:54:25.619: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) Replacing Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 00:3a:9a:77:55:a0, slot 0, interface = 13, QOS = 0
      IPv4 ACL ID = 255,
    *apfReceiveTask: Feb 11 16:54:25.619: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206  Local Bridging Vlan = 0, Local Bridging intf id = 0
    *apfReceiveTask: Feb 11 16:54:25.619: 18:3d:a2:25:01:a4 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
    *pemReceiveTask: Feb 11 16:54:25.619: 18:3d:a2:25:01:a4 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    (Cisco Controller) >*emWeb: Feb 11 16:54:46.127: 18:3d:a2:25:01:a4 Central Switch = FALSE
    *emWeb: Feb 11 16:54:46.128: 18:3d:a2:25:01:a4 Central Switch = FALSE
    (Cisco Controller) >
    (Cisco Controller) >
    (Cisco Controller) >
    (Cisco Controller) >*emWeb: Feb 11 16:55:36.461: 18:3d:a2:25:01:a4 Central Switch = FALSE
    *emWeb: Feb 11 16:55:36.463: 18:3d:a2:25:01:a4 Central Switch = FALSE
    From log i know that 802.1x passed, while dhcp don't send ip address. It seems that the local vlan id is 0 while in reality is 3... WHY ? i don't understand.
    Someone can help me to find the problem? i think the problem is on the network, the dhcp ( the corporate router) is directly connected to the ap.

    Are you setting your FlexConnect native vlan and the wlan to vlan mapping?  You also need to make sure you have the ip helpers setup and that dhcp is working.  I would configure a switch port to a vlan that the wireless users is suppose to be on locally at that site and connect a laptop to that port and make sure that the laptop gets an address.
    Thanks,
    Scott
    *****Help out other by using the rating system and marking answered questions as "Answered"*****

  • DHCP via Hyper-V VM, Server2012r2 Hyper-V host, clients not getting IP address

    You have to authorize a dhcp server as Britv8 says. That's the only way it'll start dishing out leases. That's standard for Windows DHCP server in an AD Domain.
    Also there's 0 reason to mention Hyper-V here. The whole point of virtualization is to do hardware level abstraction.

    I recently encountered this. Setup:
    Initial setup of the system was at a different location from its final destination, with different network equipment (switches) between the two. No teaming is involved, however.
    Set up the system at its final destination, with DHCP via a Hyper-V VM (Server2012r2), Server2012r2 Hyper-V host, physical clients on the lan were not getting IP address.
    The physical server box has a 4-port Intel Gigabit ethernet card.
    I moved the setup (Hyper-V Virtual Switch manager) so that the interface for the DHCP server VM was isntead using one of two built-in Broadcom adapters.
    While this topic seemed promising,
    http://community.spiceworks.com/topic/251317-hyper-v-vm-not-leasing-ip-s-dhcp
    unfortunately, "fiddling about" was not what I was looking for as possible solution.
    My notes for the resolution:
    Hyper-V system running...
    This topic first appeared in the Spiceworks Community

  • DHCP: Some clients not getting IP address

    Recently setup a new DHCP server on Mac OS X Server 10.5.8 running on an Xserve.  We migrated from a Linux server.
    The Xserve was originally just a file server.  So the only services currently running are: AFP, DHCP, NFS, and SMB.  No additional software is running.
    The DHCP server ran just fine for the first couple weeks.  But then we found some computers just stopped getting IP addresses from the DHCP server.  Some were new computers introduced to the network.  Some were laptops that had left and come back.  However, the DHCP server is definitely still giving out IP addresses and renewing them for most new and existing computers.  There have been five computers that have not gotten IP addresses so far, and that had been the case both on the wireless and on a wired connection.  Two were PC's, one running Windows 7 and one running Windows XP with Lenovo's ThinkVantage software.  The other three were different models of MacBook Pros.
    For those five computers, we managed to get them working in two ways.  One, we can select to use DHCP with a manual address.  When we do that, it manages to pick up all the other information from the DHCP server like DNS and gateway.  The second thing we can do is configure the DHCP server to supply a static IP address by providing it with the MAC address of these machines.  When we do that, the computers receive the IP address from the DHCP server.
    So I guess you could say the problem I'm experiencing is for a few computers the DHCP server seems to only be able to provide static addresses, but not dynamic ones with a lease time.
    I have logging set to the highest for the DHCP server.  Below is the first thing I noticed that keeps showing up.  Sometimes it shows a different MAC address than the one below.  None of the afflicted computers have that MAC address, though.  I have not seen any other errors in the logs for the DHCP server.
    Jan 24 12:09:47 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
    Jan 24 12:09:47 fileserver bootpd[73839]: service time 0.000304 seconds
    Jan 24 12:09:50 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
    Jan 24 12:09:50 fileserver bootpd[73839]: service time 0.000280 seconds
    Jan 24 12:09:54 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
    Jan 24 12:09:54 fileserver bootpd[73839]: service time 0.000264 seconds
    Jan 24 12:10:03 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
    Jan 24 12:10:03 fileserver bootpd[73839]: service time 0.000265 seconds
    Jan 24 12:10:11 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
    Jan 24 12:10:11 fileserver bootpd[73839]: service time 0.000283 seconds
    Jan 24 12:10:19 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
    Jan 24 12:10:19 fileserver bootpd[73839]: service time 0.000291 seconds
    Jan 24 12:10:28 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
    Jan 24 12:10:28 fileserver bootpd[73839]: service time 0.000324 seconds

    Recently setup a new DHCP server on Mac OS X Server 10.5.8 running on an Xserve.  We migrated from a Linux server.
    The Xserve was originally just a file server.  So the only services currently running are: AFP, DHCP, NFS, and SMB.  No additional software is running.
    The DHCP server ran just fine for the first couple weeks.  But then we found some computers just stopped getting IP addresses from the DHCP server.  Some were new computers introduced to the network.  Some were laptops that had left and come back.  However, the DHCP server is definitely still giving out IP addresses and renewing them for most new and existing computers.  There have been five computers that have not gotten IP addresses so far, and that had been the case both on the wireless and on a wired connection.  Two were PC's, one running Windows 7 and one running Windows XP with Lenovo's ThinkVantage software.  The other three were different models of MacBook Pros.
    For those five computers, we managed to get them working in two ways.  One, we can select to use DHCP with a manual address.  When we do that, it manages to pick up all the other information from the DHCP server like DNS and gateway.  The second thing we can do is configure the DHCP server to supply a static IP address by providing it with the MAC address of these machines.  When we do that, the computers receive the IP address from the DHCP server.
    So I guess you could say the problem I'm experiencing is for a few computers the DHCP server seems to only be able to provide static addresses, but not dynamic ones with a lease time.
    I have logging set to the highest for the DHCP server.  Below is the first thing I noticed that keeps showing up.  Sometimes it shows a different MAC address than the one below.  None of the afflicted computers have that MAC address, though.  I have not seen any other errors in the logs for the DHCP server.
    Jan 24 12:09:47 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
    Jan 24 12:09:47 fileserver bootpd[73839]: service time 0.000304 seconds
    Jan 24 12:09:50 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
    Jan 24 12:09:50 fileserver bootpd[73839]: service time 0.000280 seconds
    Jan 24 12:09:54 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
    Jan 24 12:09:54 fileserver bootpd[73839]: service time 0.000264 seconds
    Jan 24 12:10:03 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
    Jan 24 12:10:03 fileserver bootpd[73839]: service time 0.000265 seconds
    Jan 24 12:10:11 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
    Jan 24 12:10:11 fileserver bootpd[73839]: service time 0.000283 seconds
    Jan 24 12:10:19 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
    Jan 24 12:10:19 fileserver bootpd[73839]: service time 0.000291 seconds
    Jan 24 12:10:28 fileserver bootpd[73839]: DHCP DISCOVER [en1]: 1,0:23:32:c1:31:c3
    Jan 24 12:10:28 fileserver bootpd[73839]: service time 0.000324 seconds

  • Cisco ISE 1.2, Clients not getting IP address in closed mode

    Hello, I am running closed mode on my switchports. I have an issue where some clients come in in the morning, try to login, and will not get network access. I see that this is because they do not get an IP address. I am using MAB for authentication currently. They appear to MAB correctly and get Authorized in ISE, but they do not get an IP. Therefore, they also do not get the DACL of permit ANY. It's like the port gets de-authenticated during the night. Usually when the machine is rebooted it will come up with an IP address. Here is my switchport config...
     switchport access vlan 32
     switchport mode access
     switchport voice vlan 64
     logging event link-status
     authentication event fail action next-method
     authentication event server dead action authorize vlan 32
     authentication event server dead action authorize voice
     authentication event server alive action reinitialize 
     authentication host-mode multi-auth
     authentication order mab dot1x
     authentication priority dot1x mab
     authentication port-control auto
     authentication periodic
     authentication timer restart 600
     authentication timer reauthenticate 7200
     authentication violation restrict
     mab
     dot1x pae authenticator
     dot1x timeout quiet-period 300
     dot1x timeout tx-period 10
     dot1x timeout ratelimit-period 300
     dot1x timeout held-period 300
     service-policy input QoS-Input-Policy
     service-policy output QoS-Host-Port-Output-Policy
    end

    Thanks, here is the requested output of an Unauthorized client. I had to configure authentication open so they could still get access...
    SJ5051IDF1#show authen sess int g2/20 d
                Interface:  GigabitEthernet2/20
              MAC Address:  d4be.d94f.ab92
             IPv6 Address:  Unknown
             IPv4 Address:  10.42.32.109
                User-Name:  D4-BE-D9-4F-AB-92
                   Status:  Unauthorized
                   Domain:  DATA
           Oper host mode:  multi-auth
         Oper control dir:  both
          Session timeout:  N/A
        Common Session ID:  0A2A000B000034E367D4B998
          Acct Session ID:  Unknown
                   Handle:  0x21000508
           Current Policy:  POLICY_Gi2/20
    Local Policies:
    Template: DEFAULT_LINKSEC_POLICY_SHOULD_SECURE (priority 150)
          Security Policy:  Should Secure
          Security Status:  Link Unsecure
    Method status list:
           Method           State
           mab              Authc Success
    SJ5051IDF1#
    SJ5051IDF1#
    SJ5051IDF1#show ip access int g2/20
    SJ5051IDF1#
    SJ5051IDF1#
    SJ5051IDF1#show access-list int g2/20
                                    ^
    % Invalid input detected at '^' marker.
    SJ5051IDF1#show access-list ?        
      <1-2799>    ACL number
      WORD        ACL name
      ipc         Show access-list config download info
      rate-limit  Show rate-limit access lists
      |           Output modifiers
      <cr>
    SJ5051IDF1#show access-list g2/20
    SJ5051IDF1#
    SJ5051IDF1#
    SJ5051IDF1#

  • Wifi clients not getting IP addresses

    Hello Experts,
    I have a Cisco 1140 AP, and using express setup I have cnofigured a IP address to it. This AP is connected to our public network and is configured with a public ip address. We want the guest users to connect to Wifi and gain access to Internet.
    While the users connect to Wifi, I find their laptops getting IP address in series 169.x.x.x due to which they are unable to get to internet.
    Can somebody guide to what all configuration required so that laptops would get ip address?
    Thanks
    Arvind

    Hello George,
    I do not have any DHCP server, I want the AP to allocate IP addresses to wifi clients.
    Anshul,
    Is there any way the AP distribute the IP addresses? I want to have the AP act as an DHCP server and allocate IP address of wifi clients.
    If this is not possible in this AP model 1142N, any other Cisco AP model available, which can act as DHCP server?
    My requirement basically is:
    The AP should allocate IP in the range 192.168.x.x and I would connect the AP to the public network. The wifi clients should be able to get to Internet.
    Please suggest any other model in Cisco which should meet my requirement.
    Thanks
    Arvind

  • Clients not getting IP address

    Hi, I have configured 5508 with multiple APs but clients on the internal SSID aren't getting an IP address. I have the IP helper address configured and I have also disabled DHCP proxy on the controller.
    I get the following from the client debug, I don't know what the below mac address is, it's not one my APs or the clients, I am not seeing this mac address on the controller at all but it shows up in the debug.
    type = Airespace AP - Learn IP address
       on AP 6c:9c:ed:87:23:c0
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.579: 08:11:96:20:94:28 Entering Backend Auth Success state (id=29) for mobile 08:11:96:20:94:28
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.579: 08:11:96:20:94:28 Received Auth Success while in Authenticating state for mobile 08:11:96:20:94:28
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.579: 08:11:96:20:94:28 dot1x - moving mobile 08:11:96:20:94:28 into Authenticated state
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.589: 08:11:96:20:94:28 Received EAPOL-Key from mobile 08:11:96:20:94:28
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.590: 08:11:96:20:94:28 Ignoring invalid EAPOL version (1) in EAPOL-key message from mobile 08:11:96:20:94:28
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.590: 08:11:96:20:94:28 Received EAPOL-key in PTK_START state (message 2) from mobile 08:11:96:20:94:28
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.590: 08:11:96:20:94:28 PMK: Sending cache add
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.590: 08:11:96:20:94:28 Stopping retransmission timer for mobile 08:11:96:20:94:28
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.590: 08:11:96:20:94:28 Sending EAPOL-Key Message to mobile 08:11:96:20:94:28
                                                                                                                        state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.595: 08:11:96:20:94:28 Received EAPOL-Key from mobile 08:11:96:20:94:28
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.595: 08:11:96:20:94:28 Ignoring invalid EAPOL version (1) in EAPOL-key message from mobile 08:11:96:20:94:28
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.595: 08:11:96:20:94:28 Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 08:11:96:20:94:28
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.595: 08:11:96:20:94:28 apfMs1xStateInc
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.595: 08:11:96:20:94:28 0.0.0.0 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state DHCP_REQD (7)
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.595: 08:11:96:20:94:28 0.0.0.0 L2AUTHCOMPLETE (4) DHCP Not required on AP 6c:9c:ed:87:23:c0 vapId 1 apVapId 1for this client
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.595: 08:11:96:20:94:28 Not Using WMM Compliance code qosCap 00
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.595: 08:11:96:20:94:28 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 6c:9c:ed:87:23:c0 vapId 1 apVapId 1
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.595: 08:11:96:20:94:28 0.0.0.0 L2AUTHCOMPLETE (4) pemAdvanceState2 4793, Adding TMP rule
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.589: 08:11:96:20:94:28 0.0.0.0 L2AUTHCOMPLETE (4) Adding Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 6c:9c:ed:87:23:c0, slot 0, interface = 1, QOS = 0
      ACL Id = 255, Jum
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.595: 08:11:96:20:94:28 0.0.0.0 L2AUTHCOMPLETE (4) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 7006  IPv6 Vlan = 100, IPv6 intf id = 0
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.595: 08:11:96:20:94:28 0.0.0.0 L2AUTHCOMPLETE (4) Successfully plumbed mobile rule (ACL ID 255)
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.595: 08:11:96:20:94:28 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state DHCP_REQD (7)
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.595: 08:11:96:20:94:28 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 4809, Adding TMP rule
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.595: 08:11:96:20:94:28 0.0.0.0 DHCP_REQD (7) Replacing Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 6c:9c:ed:87:23:c0, slot 0, interface = 1, QOS = 0
      ACL Id = 255, Jumbo
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.595: 08:11:96:20:94:28 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 7006  IPv6 Vlan = 100, IPv6 intf id = 0
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.595: 08:11:96:20:94:28 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (ACL ID 255)
    *Dot1x_NW_MsgTask_0: Nov 25 16:14:17.596: 08:11:96:20:94:28 Stopping retransmission timer for mobile 08:11:96:20:94:28
    *pemReceiveTask: Nov 25 16:14:17.596: 08:11:96:20:94:28 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    *pemReceiveTask: Nov 25 16:14:17.596: 08:11:96:20:94:28 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0

    Fair enough.  That MAC address in the debug looks like exactyl what I'd expect to see.....  It is either the Base Radio MAC address or the Ethernet MAC Address of the AP you are associated to.   So when you say it doesn't exist on your WLC, are you sure you are comparing to the Radio MAC as well as the Ethernet MAC list?
    As far as IP addressing goes, the WLC is not seeing anything at all regarding client doing dhcp. Nor is it seeing the client send packets with an IP address (as if it were static).
    What version of code is this?
    Every single client has this problem? On this one wlan or all wlans?
    Was it ever working?
    Better yet, if this is HREAP this becomes an entirely different story, so are you doing HREAP Local Switching?

  • Guest Wireless client not getting IP addresses

    WLC 5508 as anchor  running 7.0.116.0  locally configured DHCP scope. Scope has been enabled.  There are 2 Foreign controllers in different locations Mobility ggroups have been configured   and there is communication between them  I am able to ping , mping and eping.  I have gone through my configuration but can't find what is missing.

    I am pasting the debug and show wlan  info below  the first is for the  foreign controller
    =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.09.23 07:51:16 =~=~=~=~=~=~=~=~=~=~=~=
    *apfReceiveTask: Sep 22 23:30:29.265: 00:21:5d:a9:2b:a4 Deleting mobile on AP 08:17:35:31:1c:90(0)
    *apfReceiveTask: Sep 23 12:51:08.488: 00:21:5d:a9:2b:a4 0.0.0.0 DHCP_REQD (7) DHCP Policy timeout. Number of DHCP request 0 from client
    *apfReceiveTask: Sep 23 12:51:08.488: 00:21:5d:a9:2b:a4 0.0.0.0 DHCP_REQD (7) Pem timed out, Try to delete client in 10 secs.
    *apfReceiveTask: Sep 23 12:51:08.488: 00:21:5d:a9:2b:a4 Scheduling deletion of Mobile Station: (callerId: 12) in 10 seconds
    *osapiBsnTimer: Sep 23 12:51:18.488: 00:21:5d:a9:2b:a4 apfMsExpireCallback (apf_ms.c:608) Expiring Mobile!
    *apfReceiveTask: Sep 23 12:51:18.488: 00:21:5d:a9:2b:a4 apfMsExpireMobileStation (apf_ms.c:5009) Changing state for mobile 00:21:5d:a9:2b:a4 on AP 08:17:35:31:1c:90 from Associated to Disassociated
    *apfReceiveTask: Sep 23 12:51:18.488: 00:21:5d:a9:2b:a4 Scheduling deletion of Mobile Station: (callerId: 45) in 10 seconds
    *osapiBsnTimer: Sep 23 12:51:28.488: 00:21:5d:a9:2b:a4 apfMsExpireCallback (apf_ms.c:608) Expiring Mobile!
    *apfReceiveTask: Sep 23 12:51:28.488: 00:21:5d:a9:2b:a4 apfMsAssoStateDec
    *apfReceiveTask: Sep 23 12:51:28.488: 00:21:5d:a9:2b:a4 apfMsExpireMobileStation (apf_ms.c:5132) Changing state for mobile 00:21:5d:a9:2b:a4 on AP 08:17:35:31:1c:90 from Disassociated to Idle
    *apfReceiveTask: Sep 23 12:51:28.489: 00:21:5d:a9:2b:a4 0.0.0.0 DHCP_REQD (7) Deleted mobile LWAPP rule on AP [08:17:35:31:1c:90]
    *apfReceiveTask: Sep 23 12:51:28.489: 00:21:5d:a9:2b:a4 Deleting mobile on AP 08:17:35:31:1c:90(0)
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 Adding mobile on LWAPP AP 08:17:35:31:1c:90(0)
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 Association received from mobile on AP 08:17:35:31:1c:90
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 0.0.0.0 START (0) Changing ACL 'none' (ACL ID 0) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1621)
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 Applying site-specific IPv6 override for station 00:21:5d:a9:2b:a4 - vapId 1, site 'default-group', interface 'management'
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 Applying IPv6 Interface Policy for station 00:21:5d:a9:2b:a4 - vlan 30, interface id 0, interface 'management'
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 STA - rates (8): 130 132 139 150 12 18 24 36 0 0 0 0 0 0 0 0
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state AUTHCHECK (2)
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 0.0.0.0 AUTHCHECK (2) Change state to L2AUTHCOMPLETE (4) last state L2AUTHCOMPLETE (4)
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 0.0.0.0 L2AUTHCOMPLETE (4) DHCP Not required on AP 08:17:35:31:1c:90 vapId 1 apVapId 1for this client
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 08:17:35:31:1c:90 vapId 1 apVapId 1
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state DHCP_REQD (7)
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 apfMsAssoStateInc
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 apfPemAddUser2 (apf_policy.c:223) Changing state for mobile 00:21:5d:a9:2b:a4 on AP 08:17:35:31:1c:90 from Idle to Associated
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
    *apfMsConnTask_7: Sep 23 12:51:30.796: 00:21:5d:a9:2b:a4 Sending Assoc Response to station on BSSID 08:17:35:31:1c:90 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_7: Sep 23 12:51:30.796: 00:21:5d:a9:2b:a4 apfProcessAssocReq (apf_80211.c:5241) Changing state for mobile 00:21:5d:a9:2b:a4 on AP 08:17:35:31:1c:90 from Associated to Associated
    *DHCP Socket Task: Sep 23 12:51:30.920: 00:21:5d:a9:2b:a4 DHCP received op BOOTREQUEST (1) (len 308,vlan 30, port 13, encap 0xec03)
    *DHCP Socket Task: Sep 23 12:51:30.921: 00:21:5d:a9:2b:a4 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmQueryRequested'
    *DHCP Socket Task: Sep 23 12:51:34.871: 00:21:5d:a9:2b:a4 DHCP received op BOOTREQUEST (1) (len 308,vlan 30, port 13, encap 0xec03)
    *DHCP Socket Task: Sep 23 12:51:34.871: 00:21:5d:a9:2b:a4 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmAnchorExportRequested'
    *DHCP Socket Task: Sep 23 12:51:43.998: 00:21:5d:a9:2b:a4 DHCP received op BOOTREQUEST (1) (len 308,vlan 30, port 13, encap 0xec03)
    *DHCP Socket Task: Sep 23 12:51:43.998: 00:21:5d:a9:2b:a4 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmAnchorExportRequested'
    *DHCP Socket Task: Sep 23 12:51:58.456: 00:21:5d:a9:2b:a4 DHCP received op BOOTREQUEST (1) (len 308,vlan 30, port 13, encap 0xec03)
    WLAN Identifier.................................. 1
    Profile Name..................................... calguest
    Network Name (SSID).............................. calguest
    Status........................................... Enabled
    MAC Filtering.................................... Disabled
    Broadcast SSID................................... Enabled
    AAA Policy Override.............................. Disabled
    Network Admission Control
    Radius-NAC State............................... Disabled
    SNMP-NAC State................................. Disabled
    Quarantine VLAN................................ 0
    Maximum number of Associated Clients............. 0
    Number of Active Clients......................... 2
    Exclusionlist Timeout............................ 60 seconds
    Session Timeout.................................. 1800 seconds
    CHD per WLAN..................................... Enabled
    Webauth DHCP exclusion........................... Disabled
    Interface........................................ management
    Multicast Interface.............................. Not Configured
    WLAN ACL......................................... unconfigured
    DHCP Server...................................... Default
    DHCP Address Assignment Required................. Disabled
    Static IP client tunneling....................... Disabled
    Quality of Service............................... Bronze (background)
    Scan Defer Priority.............................. 4,5,6
    Scan Defer Time.................................. 100 milliseconds
    WMM.............................................. Allowed
    WMM UAPSD Compliant Client Support............... Disabled
    Media Stream Multicast-direct.................... Disabled
    CCX - AironetIe Support.......................... Enabled
    CCX - Gratuitous ProbeResponse (GPR)............. Disabled
    CCX - Diagnostics Channel Capability............. Disabled
    Dot11-Phone Mode (7920).......................... Disabled
    Wired Protocol................................... None
    IPv6 Support..................................... Disabled
    Passive Client Feature........................... Disabled
    Peer-to-Peer Blocking Action..................... Disabled
    Radio Policy..................................... All
    DTIM period for 802.11a radio.................... 1
    DTIM period for 802.11b radio.................... 1
    Radius Servers
    Authentication................................ Global Servers
    Accounting.................................... Global Servers
    Dynamic Interface............................. Disabled
    Local EAP Authentication......................... Disabled
    Security
    802.11 Authentication:........................ Open System
    Static WEP Keys............................... Disabled
    802.1X........................................ Disabled
    Wi-Fi Protected Access (WPA/WPA2)............. Disabled
    CKIP ......................................... Disabled
    Web Based Authentication...................... Disabled
    Web-Passthrough............................... Disabled
    Conditional Web Redirect...................... Disabled
    Splash-Page Web Redirect...................... Disabled
    Auto Anchor................................... Enabled
    H-REAP Local Switching........................ Disabled
    H-REAP Local Authentication................... Disabled
    H-REAP Learn IP Address....................... Enabled
    Client MFP.................................... Optional but inactive (WPA2 not configured)
    Tkip MIC Countermeasure Hold-down Timer....... 60
    Call Snooping.................................... Disabled
    Roamed Call Re-Anchor Policy..................... Disabled
    SIP CAC Fail Send-486-Busy Policy................ Enabled
    SIP CAC Fail Send Dis-Association Policy......... Disabled
    Band Select...................................... Disabled
    Load Balancing................................... Disabled
    Mobility Anchor List
    WLAN ID IP Address Status
    1 10.12.130.114 Up
    Next is for the  anchor
    =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.09.23 07:51:16 =~=~=~=~=~=~=~=~=~=~=~=
    *apfReceiveTask: Sep 22 23:30:29.265: 00:21:5d:a9:2b:a4 Deleting mobile on AP 08:17:35:31:1c:90(0)
    *apfReceiveTask: Sep 23 12:51:08.488: 00:21:5d:a9:2b:a4 0.0.0.0 DHCP_REQD (7) DHCP Policy timeout. Number of DHCP request 0 from client
    *apfReceiveTask: Sep 23 12:51:08.488: 00:21:5d:a9:2b:a4 0.0.0.0 DHCP_REQD (7) Pem timed out, Try to delete client in 10 secs.
    *apfReceiveTask: Sep 23 12:51:08.488: 00:21:5d:a9:2b:a4 Scheduling deletion of Mobile Station: (callerId: 12) in 10 seconds
    *osapiBsnTimer: Sep 23 12:51:18.488: 00:21:5d:a9:2b:a4 apfMsExpireCallback (apf_ms.c:608) Expiring Mobile!
    *apfReceiveTask: Sep 23 12:51:18.488: 00:21:5d:a9:2b:a4 apfMsExpireMobileStation (apf_ms.c:5009) Changing state for mobile 00:21:5d:a9:2b:a4 on AP 08:17:35:31:1c:90 from Associated to Disassociated
    *apfReceiveTask: Sep 23 12:51:18.488: 00:21:5d:a9:2b:a4 Scheduling deletion of Mobile Station: (callerId: 45) in 10 seconds
    *osapiBsnTimer: Sep 23 12:51:28.488: 00:21:5d:a9:2b:a4 apfMsExpireCallback (apf_ms.c:608) Expiring Mobile!
    *apfReceiveTask: Sep 23 12:51:28.488: 00:21:5d:a9:2b:a4 apfMsAssoStateDec
    *apfReceiveTask: Sep 23 12:51:28.488: 00:21:5d:a9:2b:a4 apfMsExpireMobileStation (apf_ms.c:5132) Changing state for mobile 00:21:5d:a9:2b:a4 on AP 08:17:35:31:1c:90 from Disassociated to Idle
    *apfReceiveTask: Sep 23 12:51:28.489: 00:21:5d:a9:2b:a4 0.0.0.0 DHCP_REQD (7) Deleted mobile LWAPP rule on AP [08:17:35:31:1c:90]
    *apfReceiveTask: Sep 23 12:51:28.489: 00:21:5d:a9:2b:a4 Deleting mobile on AP 08:17:35:31:1c:90(0)
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 Adding mobile on LWAPP AP 08:17:35:31:1c:90(0)
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 Association received from mobile on AP 08:17:35:31:1c:90
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 0.0.0.0 START (0) Changing ACL 'none' (ACL ID 0) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1621)
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 Applying site-specific IPv6 override for station 00:21:5d:a9:2b:a4 - vapId 1, site 'default-group', interface 'management'
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 Applying IPv6 Interface Policy for station 00:21:5d:a9:2b:a4 - vlan 30, interface id 0, interface 'management'
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 STA - rates (8): 130 132 139 150 12 18 24 36 0 0 0 0 0 0 0 0
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state AUTHCHECK (2)
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 0.0.0.0 AUTHCHECK (2) Change state to L2AUTHCOMPLETE (4) last state L2AUTHCOMPLETE (4)
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 0.0.0.0 L2AUTHCOMPLETE (4) DHCP Not required on AP 08:17:35:31:1c:90 vapId 1 apVapId 1for this client
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 08:17:35:31:1c:90 vapId 1 apVapId 1
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state DHCP_REQD (7)
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 apfMsAssoStateInc
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 apfPemAddUser2 (apf_policy.c:223) Changing state for mobile 00:21:5d:a9:2b:a4 on AP 08:17:35:31:1c:90 from Idle to Associated
    *apfMsConnTask_7: Sep 23 12:51:30.795: 00:21:5d:a9:2b:a4 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
    *apfMsConnTask_7: Sep 23 12:51:30.796: 00:21:5d:a9:2b:a4 Sending Assoc Response to station on BSSID 08:17:35:31:1c:90 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_7: Sep 23 12:51:30.796: 00:21:5d:a9:2b:a4 apfProcessAssocReq (apf_80211.c:5241) Changing state for mobile 00:21:5d:a9:2b:a4 on AP 08:17:35:31:1c:90 from Associated to Associated
    *DHCP Socket Task: Sep 23 12:51:30.920: 00:21:5d:a9:2b:a4 DHCP received op BOOTREQUEST (1) (len 308,vlan 30, port 13, encap 0xec03)
    *DHCP Socket Task: Sep 23 12:51:30.921: 00:21:5d:a9:2b:a4 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmQueryRequested'
    *DHCP Socket Task: Sep 23 12:51:34.871: 00:21:5d:a9:2b:a4 DHCP received op BOOTREQUEST (1) (len 308,vlan 30, port 13, encap 0xec03)
    *DHCP Socket Task: Sep 23 12:51:34.871: 00:21:5d:a9:2b:a4 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmAnchorExportRequested'
    *DHCP Socket Task: Sep 23 12:51:43.998: 00:21:5d:a9:2b:a4 DHCP received op BOOTREQUEST (1) (len 308,vlan 30, port 13, encap 0xec03)
    *DHCP Socket Task: Sep 23 12:51:43.998: 00:21:5d:a9:2b:a4 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmAnchorExportRequested'
    *DHCP Socket Task: Sep 23 12:51:58.456: 00:21:5d:a9:2b:a4 DHCP received op BOOTREQUEST (1) (len 308,vlan 30, port 13, encap 0xec03)
    WLAN Identifier.................................. 1
    Profile Name..................................... calguest
    Network Name (SSID).............................. calguest
    Status........................................... Enabled
    MAC Filtering.................................... Disabled
    Broadcast SSID................................... Enabled
    AAA Policy Override.............................. Disabled
    Network Admission Control
    Radius-NAC State............................... Disabled
    SNMP-NAC State................................. Disabled
    Quarantine VLAN................................ 0
    Maximum number of Associated Clients............. 0
    Number of Active Clients......................... 2
    Exclusionlist Timeout............................ 60 seconds
    Session Timeout.................................. 1800 seconds
    CHD per WLAN..................................... Enabled
    Webauth DHCP exclusion........................... Disabled
    Interface........................................ management
    Multicast Interface.............................. Not Configured
    WLAN ACL......................................... unconfigured
    DHCP Server...................................... Default
    DHCP Address Assignment Required................. Disabled
    Static IP client tunneling....................... Disabled
    Quality of Service............................... Bronze (background)
    Scan Defer Priority.............................. 4,5,6
    Scan Defer Time.................................. 100 milliseconds
    WMM.............................................. Allowed
    WMM UAPSD Compliant Client Support............... Disabled
    Media Stream Multicast-direct.................... Disabled
    CCX - AironetIe Support.......................... Enabled
    CCX - Gratuitous ProbeResponse (GPR)............. Disabled
    CCX - Diagnostics Channel Capability............. Disabled
    Dot11-Phone Mode (7920).......................... Disabled
    Wired Protocol................................... None
    IPv6 Support..................................... Disabled
    Passive Client Feature........................... Disabled
    Peer-to-Peer Blocking Action..................... Disabled
    Radio Policy..................................... All
    DTIM period for 802.11a radio.................... 1
    DTIM period for 802.11b radio.................... 1
    Radius Servers
    Authentication................................ Global Servers
    Accounting.................................... Global Servers
    Dynamic Interface............................. Disabled
    Local EAP Authentication......................... Disabled
    Security
    802.11 Authentication:........................ Open System
    Static WEP Keys............................... Disabled
    802.1X........................................ Disabled
    Wi-Fi Protected Access (WPA/WPA2)............. Disabled
    CKIP ......................................... Disabled
    Web Based Authentication...................... Disabled
    Web-Passthrough............................... Disabled
    Conditional Web Redirect...................... Disabled
    Splash-Page Web Redirect...................... Disabled
    Auto Anchor................................... Enabled
    H-REAP Local Switching........................ Disabled
    H-REAP Local Authentication................... Disabled
    H-REAP Learn IP Address....................... Enabled
    Client MFP.................................... Optional but inactive (WPA2 not configured)
    Tkip MIC Countermeasure Hold-down Timer....... 60
    Call Snooping.................................... Disabled
    Roamed Call Re-Anchor Policy..................... Disabled
    SIP CAC Fail Send-486-Busy Policy................ Enabled
    SIP CAC Fail Send Dis-Association Policy......... Disabled
    Band Select...................................... Disabled
    Load Balancing................................... Disabled
    Mobility Anchor List
    WLAN ID IP Address Status
    1 10.12.130.114 Up

  • WLC2412-Clients Not receiving DHCP addresses

    I recently upgraded a clients WLC and they keep saying they are unable to get an IP address from the DHCP server.  It's a simple, flat network and here is what the logs are showing.  Any advice would be greatly appreciated.
    *apfReceiveTask: Apr 11 13:37:25.477: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
    *apfReceiveTask: Apr 11 13:37:17.278: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
    *apfReceiveTask: Apr 11 13:37:05.880: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
    *apfReceiveTask: Apr 11 13:13:47.397: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
    *apfReceiveTask: Apr 11 13:37:25.477: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
    *apfReceiveTask: Apr 11 13:37:17.278: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
    *apfReceiveTask: Apr 11 13:37:05.880: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
    *apfReceiveTask: Apr 11 13:13:47.397: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.

    (Cisco Controller) show>interface detailed management
    Interface Name................................... management
    MAC Address...................................... 64:00:f1:91:5d:40
    IP Address....................................... 192.168.8.3
    IP Netmask....................................... 255.255.255.0
    IP Gateway....................................... 192.168.8.1
    External NAT IP State............................ Disabled
    External NAT IP Address.......................... 0.0.0.0
    VLAN............................................. 8
    Quarantine-vlan.................................. 0
    Physical Port.................................... 1
    Primary DHCP Server.............................. 192.168.8.49
    Secondary DHCP Server............................ Unconfigured
    DHCP Option 82................................... Disabled
    ACL.............................................. Unconfigured
    AP Manager....................................... No
    Guest Interface.................................. No
    L2 Multicast..................................... Enabled

  • NCS - Wired clients not showing ip address

    I have Cisco switches reporting to NCS, I see mac addresses but no ip addresses.  I do not see any where to add a core router or arp table polling.  Has anybody got ip addresses to report on the wired side?

    NCS' management of wired infrastructure is very limited. The best wired management option is still LMS.
    You can upgrade your NCS to Prime Infrastructure 1.2 and get some additional wired management functionality (including the ability to manage your routers and thus, I believe, get the IP address correlation with the MAC addresses) but it still lags LMS's capabilities bit.

  • Clients not receiving dchp addresses from server

    Our dhcp server (windows 2012) is failing to issues addresses to the pc's. Once the lease has expired on the pc (user goes on holiday for a week) the machine will fail to pick up an ip address on the users return.
    The event viewer on the server reads "IP address range of scope is 95 percent full with only 7 IP address available"
    I have gone through the dhcp scope of which there are 94 exclusions and i have a further 39 machines which require addresses. 
    On a class C subnet i should have far more than 7 addresses available.
    Any thoughts as to what might be at fault here.  
    This topic first appeared in the Spiceworks Community

    Just completed a major network upgrade... So decided it was time to stack some ofmy old switches! Can anyone date some of these things?And some before and after shots: The first one is of a distribution cabinet (2 x 10Gig Fiber link ag. to server room) on the other side of our site, the last two are of the core cabinet in my server room. Will take some more pictures later.

  • AP12000 can not assign IP address to client

    upgrade to the latest firmware.
    want to setup ap1200 as a dhcp server for wireless client. but it seems there something wrong with setup. client cannot get IP address from AP. please take a look my configuration
    version 12.2
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    hostname xxx03
    enable secret xxx.
    username admin password xxx
    ip subnet-zero
    ip dhcp pool xxxpool3
    network 192.168.105.72 255.255.255.248
    default-router 192.168.105.65
    domain-name xxxx.com
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    ssid XXX WLAN
    authentication open
    guest-mode
    speed basic-1.0 basic-2.0 basic-5.5 basic-11.0
    rts threshold 2312
    station-role root
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface FastEthernet0
    no ip address
    no ip route-cache
    duplex auto
    speed auto
    bridge-group 1
    no bridge-group 1 source-learning
    bridge-group 1 spanning-disabled
    interface BVI1
    ip address 192.168.105.69 255.255.255.192
    no ip route-cache
    ip default-gateway 192.168.105.65
    ip http server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag/ivory/1100
    bridge 1 route ip
    line con 0
    line vty 0 4
    login local
    line vty 5 15
    login
    end

    You will need to provide some additional detail about your setup.
    Version of CRM?
    Is IDF and/or ADFS setup?
    Some basic things to check:
    From the client computer, does a nslookup of the CRM server name resolve?  If not, it may be a DNS issue.
    Is the CRM site in IIS listening to all IP addresses?  Or set to listen to only one?
    Was a host header set up in IIS for the CRM site?
    What error do you get when you use the CRM server name from the client machine?  Only IP addresses working is a sign of a kerberos issue.  Check that you have the correct SPN's created for a non machine account running the CRM app pool in IIS.
    Jason Peterson

  • Clients not receiving addresses from DHCP

    I have a Cisco 2811 router and have configured it to be a DHCP server at a remote site.  It seems like it should be pretty straight forward to configure DHCP.  Apparently I'm missing something because I can't get clients to receive an address.  Below are the applicable parts of the config.  I also have tried associating the DHCP pool with the Claims vrf and that did not work either.
    ip dhcp excluded-address 10.10.30.0 10.10.30.99
    ip dhcp excluded-address 10.10.30.201 10.10.30.255
    ip dhcp pool Claims_Office
       network 10.10.30.0 255.255.255.0
       domain-name fmi.com
       default-router 10.10.30.253
       dns-server 10.10.10.191
       lease 7
    interface FastEthernet0/0
    description Claims Office
    vrf forwarding Claims
    ip address 10.10.30.253 255.255.255.0
    duplex auto
    speed auto
    no mop enabled
    interface FastEthernet0/0/0.1205
    description Claims Office
    vrf forwarding Claims
    encapsulation dot1Q 1205
    ip address 192.168.103.2 255.255.255.252

    Unfortunately that didn't work.  Here is the output before:
    Pool Claims_Office :
     Utilization mark (high/low)    : 100 / 0
     Subnet size (first/next)       : 0 / 0
     Total addresses                : 254
     Leased addresses               : 0
     Pending event                  : none
     1 subnet is currently in the pool :
     Current index        IP address range                    Leased addresses
     10.10.30.1           10.10.30.1       - 10.10.30.254      0
    And after:
    Pool Claims_Office :
     Utilization mark (high/low)    : 100 / 0
     Subnet size (first/next)       : 0 / 0
     Total addresses                : 254
     Leased addresses               : 0
     Pending event                  : none
     1 subnet is currently in the pool :
     Current index        IP address range                    Leased addresses
     10.10.30.1           10.10.30.1       - 10.10.30.254      0
    What I want is for it to assign addresses from 10.10.30.100-199

  • VPN clients not able to ping Remote PCs & Servers : ASA 5520

    VPN is connected successfully. But not able to ping any remote ip or fqdn from client pc. But able to ping ASA 5520 firewalls inside interface. Also some clients able to access, some clients not able to access. I new to these firewalls. I tried most of ways from internet, please any one can help asap.
    Remote ip section : 192.168.1.0/24
    VPN IP Pool : 192.168.5.0/24
    Running Config :
     ip address 192.168.1.2 255.255.255.0
    interface GigabitEthernet0/2
     shutdown
     no nameif
     no security-level
     no ip address
    interface GigabitEthernet0/3
     shutdown
     no nameif
     no security-level
     no ip address
    interface Management0/0
     shutdown
     no nameif
     no security-level
     no ip address
     management-only
    passwd z40TgSyhcLKQc3n1 encrypted
    boot system disk0:/asa722-k8.bin
    ftp mode passive
    clock timezone GST 4
    dns domain-lookup outside
    dns domain-lookup inside
    dns server-group DefaultDNS
     name-server 213.42.20.20
     domain-name default.domain.invalid
    access-list outtoin extended permit tcp any host 83.111.113.114 eq 3389
    access-list outtoin extended permit tcp any host 83.111.113.113 eq https
    access-list outtoin extended permit tcp any host 83.111.113.114 eq smtp
    access-list outtoin extended permit tcp any host 83.111.113.114 eq https
    access-list outtoin extended permit tcp any host 83.111.113.114 eq www
    access-list outtoin extended permit tcp any host 83.111.113.115 eq https
    access-list outtoin extended permit tcp any host 94.56.148.98 eq 3389
    access-list outtoin extended permit tcp any host 83.111.113.117 eq ssh
    access-list fualavpn_splitTunnelAcl standard permit 192.168.1.0 255.255.255.0
    access-list outside_nat0_outbound extended permit ip 192.168.5.0 255.255.255.0
    92.168.1.0 255.255.255.0
    access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 1
    2.168.5.0 255.255.255.0
    access-list inet_in extended permit icmp any any time-exceeded
    access-list inet_in extended permit icmp any any unreachable
    access-list inet_in extended permit icmp any any echo-reply
    access-list inet_in extended permit icmp any any echo
    pager lines 24
    logging enable
    logging asdm informational
    logging from-address [email protected]
    logging recipient-address [email protected] level errors
    logging recipient-address [email protected] level emergencies
    logging recipient-address [email protected] level errors
    mtu outside 1500
    mtu inside 1500
    ip local pool fualapool 192.168.5.10-192.168.5.50 mask 255.255.255.0
    ip local pool VPNPool 192.168.5.51-192.168.5.150 mask 255.255.255.0
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-522.bin
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound outside
    nat (inside) 1 192.168.1.0 255.255.255.0
    static (inside,outside) 94.56.148.98 192.168.1.11 netmask 255.255.255.255
    static (inside,outside) 83.111.113.114 192.168.1.111 netmask 255.255.255.255
    access-group inet_in in interface outside
    route outside 0.0.0.0 0.0.0.0 83.111.113.116 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout uauth 0:05:00 absolute
    group-policy DfltGrpPolicy attributes
     banner none
     wins-server none
     dns-server none
     dhcp-network-scope none
     vpn-access-hours none
     vpn-simultaneous-logins 10
     vpn-idle-timeout 30
     vpn-session-timeout none
     vpn-filter none
     vpn-tunnel-protocol IPSec l2tp-ipsec webvpn
     password-storage disable
     ip-comp disable
     re-xauth disable
     group-lock none
     pfs disable
     ipsec-udp disable
     ipsec-udp-port 10000
     split-tunnel-policy tunnelall
     split-tunnel-network-list none
     default-domain none
     split-dns none
     intercept-dhcp 255.255.255.255 disable
     secure-unit-authentication disable
     user-authentication disable
     user-authentication-idle-timeout 30
     ip-phone-bypass disable
     leap-bypass disable
     nem disable
     backup-servers keep-client-config
     msie-proxy server none
     msie-proxy method no-modify
     msie-proxy except-list none
     msie-proxy local-bypass disable
     nac disable
     nac-sq-period 300
     nac-reval-period 36000
     nac-default-acl none
     address-pools none
     client-firewall none
     client-access-rule none
     webvpn
      functions url-entry
      html-content-filter none
      homepage none
      keep-alive-ignore 4
      http-comp gzip
      filter none
      url-list none
      customization value DfltCustomization
      port-forward none
      port-forward-name value Application Access
      sso-server none
      deny-message value Login was successful, but because certain criteria have no
     been met or due to some specific group policy, you do not have permission to u
    e any of the VPN features. Contact your IT administrator for more information
      svc none
      svc keep-installer installed
      svc keepalive none
      svc rekey time none
      svc rekey method none
      svc dpd-interval client none
      svc dpd-interval gateway none
      svc compression deflate
    group-policy fualavpn internal
    group-policy fualavpn attributes
     dns-server value 192.168.1.111 192.168.1.100
     vpn-tunnel-protocol IPSec
     split-tunnel-policy tunnelspecified
     split-tunnel-network-list value fualavpn_splitTunnelAcl
    username test password I7ZgrgChfw4FV2AW encrypted privilege 0
    username Mohamed password Vqmmt8cR/.Qu7LhU encrypted privilege 0
    username Moghazi password GMr7xgdqmGEQ2SVR encrypted privilege 0
    username Moghazi attributes
     password-storage enable
    username fualauaq password E6CgvoOpTKphiM2U encrypted privilege 0
    username fualauaq attributes
     password-storage enable
    username fuala password IFtijSYb7LAOV/IW encrypted privilege 15
    username Basher password Djf15nXIJXmayfjY encrypted privilege 0
    username Basher attributes
     password-storage enable
    username fualafac password VGC/7cKXW1A6eyXS encrypted privilege 0
    username fualafac attributes
     password-storage enable
    username fualaab password ONTH8opuP4RKgRXD encrypted privilege 0
    username fualaab attributes
     password-storage enable
    username fualaadh2 password mNEgLxzPBeF4SyDb encrypted privilege 0
    username fualaadh2 attributes
     password-storage enable
    username fualaain2 password LSKk6slwsVn4pxqr encrypted privilege 0
    username fualaain2 attributes
     password-storage enable
    username fualafj2 password lE4Wu7.5s7VXwCqv encrypted privilege 0
    username fualafj2 attributes
     password-storage enable
    username fualakf2 password 38oMUuwKyShs4Iid encrypted privilege 0
    username fualakf2 attributes
     password-storage enable
    username fualaklb password .3AMGUZ1NWU1zzIp encrypted privilege 0
    username fualaklb attributes
     password-storage enable
    username fualastr password RDXSdBgMaJxNLnaH encrypted privilege 0
    username fualastr attributes
     password-storage enable
    username fualauaq2 password HnjodvZocYhDKrED encrypted privilege 0
    username fualauaq2 attributes
     password-storage enable
    username fualastore password wWDVHfUu9pdM9jGj encrypted privilege 0
    username fualastore attributes
     password-storage enable
    username fualadhd password GK8k1MkMlIDluqF4 encrypted privilege 0
    username fualadhd attributes
     password-storage enable
    username fualaabi password eYL0j16kscNhhci4 encrypted privilege 0
    username fualaabi attributes
     password-storage enable
    username fualaadh password GTs/9BVCAU0TRUQE encrypted privilege 0
    username fualaadh attributes
     password-storage enable
    username fualajuh password b9QGJ1GHhR88reM1 encrypted privilege 0
    username fualajuh attributes
     password-storage enable
    username fualadah password JwVlqQNIellNgxnZ encrypted privilege 0
    username fualadah attributes
     password-storage enable
    username fualarak password UE41e9hpvcMeChqx encrypted privilege 0
    username fualarak attributes
     password-storage enable
    username fualasnk password ZwZ7fVglexrCWFUH encrypted privilege 0
    username fualasnk attributes
     password-storage enable
    username rais password HrvvrIw5tEuam/M8 encrypted privilege 0
    username rais attributes
     password-storage enable
    username fualafuj password yY2jRMPqmNGS.3zb encrypted privilege 0
    username fualafuj attributes
     password-storage enable
    username fualamaz password U1YUfQzFYrsatEzC encrypted privilege 0
    username fualamaz attributes
     password-storage enable
    username fualashj password gN4AXk/oGBTEkelQ encrypted privilege 0
    username fualashj attributes
     password-storage enable
    username fualabdz password tg.pB7RXJx2CWKWi encrypted privilege 0
    username fualabdz attributes
     password-storage enable
    username fualamam password uwLjc0cV7LENI17Y encrypted privilege 0
    username fualamam attributes
     password-storage enable
    username fualaajm password u3yLk0Pz0U1n.Q0c encrypted privilege 0
    username fualaajm attributes
     password-storage enable
    username fualagrm password mUt3A60gLJ8N5HVr encrypted privilege 0
    username fualagrm attributes
     password-storage enable
    username fualakfn password ceTa6jmvnzOFNSgF encrypted privilege 0
    username fualakfn attributes
     password-storage enable
    username Fualaain password Yyhr.dlc6/J7WvF0 encrypted privilege 0
    username Fualaain attributes
     password-storage enable
    username fualaban password RCJKLGTrh7VM2EBW encrypted privilege 0
    username John password D9xGV1o/ONPM9YNW encrypted privilege 15
    username John attributes
     password-storage disable
    username wrkshopuaq password cFKpS5e6Whp0A7TZ encrypted privilege 0
    username wrkshopuaq attributes
     password-storage enable
    username Talha password 3VoAABwXxVonLmWi encrypted privilege 0
    username Houssam password Cj/uHUqsj36xUv/R encrypted privilege 0
    username Faraj password w2qYfE3DkYvS/oPq encrypted privilege 0
    username Faraj attributes
     password-storage enable
    username gowth password HQhALLeiQXuIzptCnTv1rA== nt-encrypted privilege 15
    username Hameed password 0Kr0N1VRmLuWdoDE encrypted privilege 0
    username Hameed attributes
     password-storage enable
    username Hassan password Uy4ASuiNyEd70LCw encrypted privilege 0
    username cisco password IPVBkPI1GLlHurPD encrypted privilege 15
    username Karim password 5iOtm58EKMyvruZA encrypted privilege 0
    username Shakir password BESX2bAvlbqbDha/ encrypted privilege 0
    username Riad password iB.miiOF7qMESlCL encrypted privilege 0
    username Azeem password 0zAqiCG8dmLyRQ8f encrypted privilege 15
    username Azeem attributes
     password-storage disable
    username Osama password xu66er.7duIVaP79 encrypted privilege 0
    username Osama attributes
     password-storage enable
    username Mahmoud password bonjr0B19aOQSpud encrypted privilege 0
    username alpha password x8WO0aiHL3pVFy2E encrypted privilege 15
    username Wissam password SctmeK/qKVNLh/Vv encrypted privilege 0
    username Wissam attributes
     password-storage enable
    username Nabil password m4fMvkTgVwK/O3Ms encrypted privilege 0
    aaa authentication telnet console LOCAL
    aaa authentication ssh console LOCAL
    aaa authentication enable console LOCAL
    http server enable
    http 0.0.0.0 0.0.0.0 outside
    http 192.168.1.4 255.255.255.255 inside
    http 192.168.1.100 255.255.255.255 inside
    http 192.168.1.111 255.255.255.255 inside
    http 192.168.1.200 255.255.255.255 inside
    http 83.111.113.117 255.255.255.255 outside
    http 192.168.1.17 255.255.255.255 inside
    http 192.168.1.16 255.255.255.255 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto dynamic-map outside_dyn_map 20 set pfs
    crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
    crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
     authentication pre-share
     encryption 3des
     hash sha
     group 2
     lifetime 86400
    tunnel-group fualavpn type ipsec-ra
    tunnel-group fualavpn type ipsec-ra
    tunnel-group fualavpn general-attributes
     address-pool fualapool
     address-pool VPNPool
     default-group-policy fualavpn
    tunnel-group fualavpn ipsec-attributes
     pre-shared-key *
    tunnel-group fualavpn ppp-attributes
     authentication pap
     authentication ms-chap-v2
     authentication eap-proxy
    telnet 0.0.0.0 0.0.0.0 outside
    telnet 0.0.0.0 0.0.0.0 inside
    telnet timeout 5
    ssh 0.0.0.0 0.0.0.0 outside
    ssh 192.168.1.0 255.255.255.0 inside
    ssh timeout 5
    console timeout 0
    management-access inside
    class-map inspection_default
     match default-inspection-traffic
    policy-map type inspect dns migrated_dns_map_1
     parameters
      message-length maximum 512
    policy-map global_policy
     class inspection_default
      inspect dns migrated_dns_map_1
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect icmp
      inspect icmp error
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:38e41e83465d37f69542355df734db35
    : end

    Hi,
    What about translating the traffic on the local ASA (Active unit) for traffic received from the VPN tunnel to the internal interface IP address? You can try something like nat (outside,inside) source dynamic obj-VpnRemoteTraffic interface destination static StandbyIP StandbyIP
    Regards,

  • ORA-16191: Primary log shipping client not logged on standby.

    Hi,
    Please help me in the following scenario. I have two nodes ASM1 & ASM2 with RHEL4 U5 OS. On node ASM1 there is database ORCL using ASM diskgroups DATA & RECOVER and archive location is on '+RECOVER/orcl/'. On ASM2 node, I have to configure STDBYORCL (standby) database using ASM. I have taken the copy of database ORCL via RMAN, as per maximum availability architecture.
    Then I have ftp'd all to ASM2 and put them on FS /u01/oradata. Have made all necessary changes in primary and standby database pfile and then perform the duplicate database for standby using RMAN in order to put the db files in desired diskgroups. I have mounted the standby database but unfortunately, log transport service is not working and archives are not getting shipped to standby host.
    Here are all configuration details.
    Primary database ORCL pfile:
    [oracle@asm dbs]$ more initorcl.ora
    stdbyorcl.__db_cache_size=251658240
    orcl.__db_cache_size=226492416
    stdbyorcl.__java_pool_size=4194304
    orcl.__java_pool_size=4194304
    stdbyorcl.__large_pool_size=4194304
    orcl.__large_pool_size=4194304
    stdbyorcl.__shared_pool_size=100663296
    orcl.__shared_pool_size=125829120
    stdbyorcl.__streams_pool_size=0
    orcl.__streams_pool_size=0
    *.audit_file_dest='/opt/oracle/admin/orcl/adump'
    *.background_dump_dest='/opt/oracle/admin/orcl/bdump'
    *.compatible='10.2.0.1.0'
    *.control_files='+DATA/orcl/controlfile/current.270.665007729','+RECOVER/orcl/controlfile/current.262.665007731'
    *.core_dump_dest='/opt/oracle/admin/orcl/cdump'
    *.db_block_size=8192
    *.db_create_file_dest='+DATA'
    *.db_domain=''
    *.db_file_multiblock_read_count=16
    *.db_name='orcl'
    *.db_recovery_file_dest='+RECOVER'
    *.db_recovery_file_dest_size=3163553792
    *.db_unique_name=orcl
    *.fal_client=orcl
    *.fal_server=stdbyorcl
    *.instance_name='orcl'
    *.job_queue_processes=10
    *.log_archive_config='dg_config=(orcl,stdbyorcl)'
    *.log_archive_dest_1='LOCATION=USE_DB_RECOVERY_FILE_DEST'
    *.log_archive_dest_2='SERVICE=stdbyorcl'
    *.log_archive_dest_state_1='ENABLE'
    *.log_archive_dest_state_2='ENABLE'
    *.log_archive_format='%t_%s_%r.dbf'
    *.open_cursors=300
    *.pga_aggregate_target=121634816
    *.processes=150
    *.remote_login_passwordfile='EXCLUSIVE'
    *.sga_target=364904448
    *.standby_file_management='AUTO'
    *.undo_management='AUTO'
    *.undo_tablespace='UNDOTBS'
    *.user_dump_dest='/opt/oracle/admin/orcl/udump'
    Standby database STDBYORCL pfile:
    [oracle@asm2 dbs]$ more initstdbyorcl.ora
    stdbyorcl.__db_cache_size=251658240
    stdbyorcl.__java_pool_size=4194304
    stdbyorcl.__large_pool_size=4194304
    stdbyorcl.__shared_pool_size=100663296
    stdbyorcl.__streams_pool_size=0
    *.audit_file_dest='/opt/oracle/admin/stdbyorcl/adump'
    *.background_dump_dest='/opt/oracle/admin/stdbyorcl/bdump'
    *.compatible='10.2.0.1.0'
    *.control_files='u01/oradata/stdbyorcl_control01.ctl'#Restore Controlfile
    *.core_dump_dest='/opt/oracle/admin/stdbyorcl/cdump'
    *.db_block_size=8192
    *.db_create_file_dest='/u01/oradata'
    *.db_domain=''
    *.db_file_multiblock_read_count=16
    *.db_name='orcl'
    *.db_recovery_file_dest='+RECOVER'
    *.db_recovery_file_dest_size=3163553792
    *.db_unique_name=stdbyorcl
    *.fal_client=stdbyorcl
    *.fal_server=orcl
    *.instance_name='stdbyorcl'
    *.job_queue_processes=10
    *.log_archive_config='dg_config=(orcl,stdbyorcl)'
    *.log_archive_dest_1='LOCATION=USE_DB_RECOVERY_FILE_DEST'
    *.log_archive_dest_2='SERVICE=orcl'
    *.log_archive_dest_state_1='ENABLE'
    *.log_archive_dest_state_2='ENABLE'
    *.log_archive_format='%t_%s_%r.dbf'
    *.log_archive_start=TRUE
    *.open_cursors=300
    *.pga_aggregate_target=121634816
    *.processes=150
    *.remote_login_passwordfile='EXCLUSIVE'
    *.sga_target=364904448
    *.standby_archive_dest='LOCATION=USE_DB_RECOVERY_FILE_DEST'
    *.standby_file_management='AUTO'
    *.undo_management='AUTO'
    *.undo_tablespace='UNDOTBS'
    *.user_dump_dest='/opt/oracle/admin/stdbyorcl/udump'
    db_file_name_convert=('+DATA/ORCL/DATAFILE','/u01/oradata','+RECOVER/ORCL/DATAFILE','/u01/oradata')
    log_file_name_convert=('+DATA/ORCL/ONLINELOG','/u01/oradata','+RECOVER/ORCL/ONLINELOG','/u01/oradata')
    Have configured the tns service on both the hosts and its working absolutely fine.
    <p>
    ASM1
    =====
    [oracle@asm dbs]$ tnsping stdbyorcl
    </p>
    <p>
    TNS Ping Utility for Linux: Version 10.2.0.1.0 - Production on 19-SEP-2008 18:49:00
    </p>
    <p>
    Copyright (c) 1997, 2005, Oracle. All rights reserved.
    </p>
    <p>
    Used parameter files:
    </p>
    <p>
    Used TNSNAMES adapter to resolve the alias
    Attempting to contact (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.20.20)(PORT = 1521))) (CONNECT_DATA = (SID = stdbyorcl) (SERVER = DEDICATED)))
    OK (30 msec)
    ASM2
    =====
    </p>
    <p>
    [oracle@asm2 archive]$ tnsping orcl
    </p>
    <p>
    TNS Ping Utility for Linux: Version 10.2.0.1.0 - Production on 19-SEP-2008 18:48:39
    </p>
    <p>
    Copyright (c) 1997, 2005, Oracle. All rights reserved.
    </p>
    <p>
    Used parameter files:
    </p>
    <p>
    Used TNSNAMES adapter to resolve the alias
    Attempting to contact (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.20.10)(PORT = 1521))) (CONNECT_DATA = (SID = orcl) (SERVER = DEDICATED)))
    OK (30 msec)
    Please guide where I am missing. Thanking you in anticipation.
    Regards,
    Ravish Garg

    Following are the errors I am receiving as per alert log.
    ORCL alert log:
    Thu Sep 25 17:49:14 2008
    ARCH: Possible network disconnect with primary database
    Thu Sep 25 17:49:14 2008
    Error 1031 received logging on to the standby
    Thu Sep 25 17:49:14 2008
    Errors in file /opt/oracle/admin/orcl/bdump/orcl_arc1_4825.trc:
    ORA-01031: insufficient privileges
    FAL[server, ARC1]: Error 1031 creating remote archivelog file 'STDBYORCL'
    FAL[server, ARC1]: FAL archive failed, see trace file.
    Thu Sep 25 17:49:14 2008
    Errors in file /opt/oracle/admin/orcl/bdump/orcl_arc1_4825.trc:
    ORA-16055: FAL request rejected
    ARCH: FAL archive failed. Archiver continuing
    Thu Sep 25 17:49:14 2008
    ORACLE Instance orcl - Archival Error. Archiver continuing.
    Thu Sep 25 17:49:44 2008
    FAL[server]: Fail to queue the whole FAL gap
    GAP - thread 1 sequence 40-40
    DBID 1192788465 branch 665007733
    Thu Sep 25 17:49:46 2008
    Thread 1 advanced to log sequence 48
    Current log# 2 seq# 48 mem# 0: +DATA/orcl/onlinelog/group_2.272.665007735
    Current log# 2 seq# 48 mem# 1: +RECOVER/orcl/onlinelog/group_2.264.665007737
    Thu Sep 25 17:55:43 2008
    Shutting down archive processes
    Thu Sep 25 17:55:48 2008
    ARCH shutting down
    ARC2: Archival stopped
    STDBYORCL alert log:
    ==============
    Thu Sep 25 17:49:27 2008
    Errors in file /opt/oracle/admin/stdbyorcl/bdump/stdbyorcl_arc0_4813.trc:
    ORA-01017: invalid username/password; logon denied
    Thu Sep 25 17:49:27 2008
    Error 1017 received logging on to the standby
    Check that the primary and standby are using a password file
    and remote_login_passwordfile is set to SHARED or EXCLUSIVE,
    and that the SYS password is same in the password files.
    returning error ORA-16191
    It may be necessary to define the DB_ALLOWED_LOGON_VERSION
    initialization parameter to the value "10". Check the
    manual for information on this initialization parameter.
    Thu Sep 25 17:49:27 2008
    Errors in file /opt/oracle/admin/stdbyorcl/bdump/stdbyorcl_arc0_4813.trc:
    ORA-16191: Primary log shipping client not logged on standby
    PING[ARC0]: Heartbeat failed to connect to standby 'orcl'. Error is 16191.
    Thu Sep 25 17:51:38 2008
    FAL[client]: Failed to request gap sequence
    GAP - thread 1 sequence 40-40
    DBID 1192788465 branch 665007733
    FAL[client]: All defined FAL servers have been attempted.
    Check that the CONTROL_FILE_RECORD_KEEP_TIME initialization
    parameter is defined to a value that is sufficiently large
    enough to maintain adequate log switch information to resolve
    archivelog gaps.
    Thu Sep 25 17:55:16 2008
    Errors in file /opt/oracle/admin/stdbyorcl/bdump/stdbyorcl_arc0_4813.trc:
    ORA-01017: invalid username/password; logon denied
    Thu Sep 25 17:55:16 2008
    Error 1017 received logging on to the standby
    Check that the primary and standby are using a password file
    and remote_login_passwordfile is set to SHARED or EXCLUSIVE,
    and that the SYS password is same in the password files.
    returning error ORA-16191
    It may be necessary to define the DB_ALLOWED_LOGON_VERSION
    initialization parameter to the value "10". Check the
    manual for information on this initialization parameter.
    Thu Sep 25 17:55:16 2008
    Errors in file /opt/oracle/admin/stdbyorcl/bdump/stdbyorcl_arc0_4813.trc:
    ORA-16191: Primary log shipping client not logged on standby
    PING[ARC0]: Heartbeat failed to connect to standby 'orcl'. Error is 16191.
    Please suggest where I am missing.
    Regards,
    Ravish Garg

Maybe you are looking for

  • Storing internal table from XML File into DDIC

    Hi everybody, im trying to store an internal table <b>without</b> knowing the content - means the structure (fields)- into th DDIC, but i failed. The code is: DATA xslt_error TYPE REF TO cx_xslt_exception. TRY . perform load_file  using 'D:/usr/YTGVF

  • Transfer from iPod to iTunes?

    I bet this gets asked a lot, but my hard drive crashed so I got a new one with nothing on it. I have all my old music on my iPod though, so I'm wondering if there is some way to get them back on my hard drive / iTunes somehow...

  • Compiler Error Message: CS0433

    Compiler Error Message: CS0433: The type 'CrystalDecisions.Web.CrystalReportPartsViewer' exists in both 'c:\WINDOWS\assembly\GAC_MSIL\CrystalDecisions.Web\11.5.3700.0__692fbea5521e1304\CrystalDecisions.Web.dll' and 'c:\WINDOWS\assembly\GAC_MSIL\Cryst

  • Print problem for Officejet 6700

    Recently I have been having trouble in printing the word document.  I was working about 3-4 days ago. I have windows XP with MS Word 2010.  The print is HP Officejet 6700 Premium.  I always use it in the offline mode.  It's connected to the computer

  • Only first bookmark will print

    I have combined a number of small PDF files into one. Each former individual file is represented as a bookmark in the combined file. However if a user tries to print the pages of the second, fourth and tenth bookmarks from the combined file, only the