Compaq Multiport Evo n800c wlan help needed(long)

I am having problems getting my wireless network module working. I ran the hotplug script when i first attempted to get this working. The difference with the multiport card, is that to initially enable the device one must enable it by pressing, function(Fn)+F2.
When i enable the device with this key press i notice that the prism2_usb module is loaded via lsmod.
prism2_usb 76932 0
p80211 32272 1 prism2_usb
When i researched the module needed for this multiport device, there are many different opinions on compaq multiports, as well as many problems with them. The Orinocco modules and and Prism modules were mentioned as "working" modules(via hp linux forums/googling/mailing lists).
I assumed that the prism modules were the correct ones to use, since they are loaded when the device is enabled(i assumed these modules were selected by hotplug). Maybe this is where I am wrong, but moving on.
I then downloaded the wirelesstools package so that i can utilize the command iwconfig, and to help with wlan devices.
Im very new to arch-linux, so I dont know where to go at this point. The wireless networking does not work with this module loaded.
iwconfig
lo no wireless extensions.
sit0 no wireless extensions.
eth0 no wireless extensions.
wlan0 no wireless extensions.
ifconfig -a
wlan0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
BROADCAST NOTRAILERS MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
I do think something is wrong with the module maybe, because of the fact that no hardware address is represented. I could be wrong being that im new to arch/linux. But again I do not know how the multiport modules from compaq work.
/etc/rc.d/wlan start
Starting WLAN Devices: FATAL: Module wlan0 not found.
FATAL: Module wlan0 not found.
message=lnxreq_ifstate
ifstate=fwload
resultcode=implementation_failure
prism2dl: No such device
load_cardpda failed, exiting.
Unknown prism2 hardware type (), assuming SSF
Processing PDR file: /tmp/prism2_ssf.pda
prism2dl: No such device
Couldn't fetch PRI-SUP info
Warning: RAM load only, PDA changes will NOT be written to flash.
Reading S-record file /etc/wlan//prism2_pm.hex...
NIC ID: 0 v0.0.0
MFI ID: 0 v0 0->0
CFI ID: 0 v0 0->0
PRI ID: 0 v0 0->0
Version: ID 0x15 1.1.2
Compat: Role 0 Id 0x3 v2 4->4
Compat: Role 0x1 Id 0x2 v2 1->1
Seq: 0
Platform: ID 0x800e 1.0.0
Platform: ID 0x8015 1.0.0
Platform: ID 0x8019 1.0.0
Platform: ID 0x801d 1.0.0
Platform: ID 0x8024 1.0.0
prism2dl: warning: Failed to find PDR for plugrec 0x0003.
prism2dl: warning: Failed to find PDR for plugrec 0x0005.
prism2dl: warning: Failed to find PDR for plugrec 0x0006.
prism2dl: warning: Failed to find PDR for plugrec 0x0007.
prism2dl: warning: Failed to find PDR for plugrec 0x0008.
prism2dl: warning: Failed to find PDR for plugrec 0x0402.
prism2dl: warning: Failed to find PDR for plugrec 0x0403.
prism2dl: warning: Failed to find PDR for plugrec 0x0404.
prism2dl: warning: Failed to find PDR for plugrec 0x0408.
prism2dl: warning: Failed to find PDR for plugrec 0x0001.
prism2dl: No such device
prism2dl: writeimage()->do_ioctl() failed w/ result=19, aborting download
prism2dl: Failed to ramwrite image data for /etc/wlan//prism2_pm.hex, exiting.
prism2dl: No such device
load_cardpda failed, exiting.
Firmware failed to load for device wlan0
This makes me further the thought of the module not being correct, because the wlan0 device is not even recognized.
Now that I think the module is wrong I rmmod the modules Ithat were loaded when powering on the device.(prism2_usb/p80211). I then load the orinoco modules via modprobe orinoco.
lsmod
orinoco 44428 0
hermes 8320 1 orinoco
iwconfig
lo no wireless extensions.
sit0 no wireless extensions.
eth0 no wireless extensions.
/etc/rc.d/wlan start
Starting WLAN Devices: FATAL: Module wlan0 not found.
FATAL: Module wlan0 not found.
Error: Device wlan0 does not seem to be present.
Make sure you've inserted the appropriate
modules or that your modules.conf file contains
the appropriate aliase(s).
I do have to most recent wlan-ng26 drivers: wlancfg version: 0.2.1-pre21
I tried to figure out the exact chipset but I had no luck with this, since the multiport device is on a usb hub/uses usb. So this device was not listed in lspic, and I have the ohci-hcd module loaded via rc.conf.
I also have included the line, wlan0="dhcp" n INTERFACES=(lo eth0 wlan0), in my rc.conf.
Which brings me here, with no idea of what to try to do. I hope I have included enough information. If anyone needs any more information I will gladly provide it. Any help would be greatly appreciated.

i0m also relatively newbie for wireless, but at least i have mine working
what i wonder about your config, is, why do you use wlan0 ?
i myself have eth0 (normal, using e100), eth1 (firewire), eth2 (wireless, using orinoco_pci) and it seems to work like this:
modprobe orinoco_pci
(what is managed for you with hotplug, hopefully)
then
iwconfig ......
using all options needed for the net i want to login
then
dhcpcd eth2
and then it works simply
so i have nowhere wlan0, but i don't use hotplug for this
anyone knowning more feel free to correct me :-)

Similar Messages

URGENT HELP NEEDED - iPhone 3Gs no longer detected or charged by MacBook

My iPhone 3Gs (3.1) has been running fine, until several hours ago today, when I plugged it to my MacBook, the iPhone is no longer detected - it doesn't show up in iTunes, nor it is charged. I tried opening iPhoto, and it wasn't there too. Not with Image Capture too. I tried charging it using the out-of-box wall charger using the same out-of-box USB cable I use for MacBook, and it can be charged without any problem. Then I put it into Recovery mode, and there iTunes can see it. I don't want to restore it before I figure out exactly what went wrong, as I don't want the restore process somehow gets stuck in the middle that the connection is lost again.
I've tried reinstalled iTunes, including completely removal of Apple Mobile Device Support, as instructed by Apple. But still no luck.
I've tried switching to another USB port of my MacBook. No luck.
My iTunes is the latest 9.0.1, and my Mac OSX is 10.6.1. My iPhone is on 3.1, upgraded from 3.0.
I've read from web that it seems I'm not the only one out there having this problem. But none of them seem having any real working solution.
Urgent help needed & appreciated. Millions of thanks in advance.
Gary

1. I used both cables - theirs & mine ... and on several macs
2. yes, same cable for wall & mac
3. as said, i did completely remove & install itunes (incl. apple mobile device support), as instructed on the apple webpage
anyway, did a restore just now. it seems okay now. but the problem is i have no idea what cause this, and i can't replicate the problem. so i don't know when it will happen again ... maybe a bug with os 3.1 ... others on web said os 3.1 is quite buggy ...

Troubleshoting help needed: My iMac keeps crashing and restarting with a report detail: "spinlock application timed out" What can I do to fix this?timed out"

Troubleshooting help needed: My iMac keeps crashing and restarting with a notice: "Spinlock application timed out" What can I do?

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the page that opens.
Select the most recent panic log under System Diagnostic Reports. Post the contents — the text, please, not a screenshot. In the interest of privacy, I suggest you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header and body of the report, if it’s present (it may not be.) Please don't post shutdownStall, spin, or hang reports.

Help needed I have a canon 40D. I am thinking of buying a canon 6D.But not sure that my len

Hi all help needed I have a canon 40D. I am thinking of buying a canon 6D.
But not sure that my lenses will work.
I have a 170mm/ 500mm APO Sigma.
A 10/20 ex Sigma HSM IF.
And a 180 APO Sigma Macro or do I have to scrap them and buy others.
ALL Help will be greatly received. Yours BRODIE

In short, I love it. I was going to buy the 5DMark III. After playing with it for a while at my local Fry's store where they put 5DMII, 5DMIII and 6D next to each other, using the same 24-105L lens, I decided to get the 6D and pocket the different for lens later.
I'm upgrading from the 30D. So I think you'll love it. It's a great camera. I have used 5DMII extensively before (borrowing from a close friend).
Funny thing is at first I don't really care about the GPS and Wifi much. I thought they're just marketing-gimmick. But once you have it, it is actually really fun and helpful. For example, I can place the 6D on a long "monopod", then use the app on the phone to control the camera to get some unique perspective on some scenes. It's fun and great. GPS is also nice for travel guy like me.
Weekend Travelers Blog | Eastern Sierra Fall Color Guide

Help needed asap! Will my IPAD 3G wifi work in another country with the sim of a 3G services provider?

Help needed asap! I want to buy an IPAD 3G + Wifi before I return to my country from the US. The problem is that I have GSM service providers in my country that provide 3G services but I am wondering if their SIM card would work in the IPAD? In other words, can I get an unlocked IPAD 3G wifi? Thanks for helping out

The AT&T 3G iPads (which are GSM/sim based) in the US are not locked (the Verizon models are CDMA based so they effectively are). So as long as you can get a sim in your own country you shouldn't have a problem

EDI IDOC generation for interface with Vendor software help needed.

EDI IDOC help needed.
We are NOT an EDI shop, but have a project to output data to Sales Force.com
Sales Force requests IDOC output - eg. 810 Outbound Invoice.
We will need to do a historical load of Orders/Quotes/Invoices from the past 2 years.
Is there a function module or series of FM's that are used to generate the E2EDKxxxxx type segments?
I have been testing using the IDOC_OUTPUT_INVOIC and IDOC_OUTPUT_ORDRSP FM's, but they generate segments begining with E1EDKxxxxx.
Basicall we have a report program that the user enteres in the date range of Order/Quotes/Invoices they wish to extract, the the program needs to output a flat file (.txt) on the server which is then picked up by Sales Force.com.
Also, is there a way to have in the Partner Profile a generic Partner under the "Type KU" that can be used for all orders/invoices so I don't have to create a KU Partner Type for each and every Sold-To customer we have?
I am very new to EDI so any help would be greatly appreciated.
Thanks.
Scott.

Hi Scott,
We will need to do a historical load of Orders/Quotes/Invoices from the past 2 years.
I know it's very tempting to use an interface for such loads if you anyhow have to create one. However, often the volume alone speaks against interface usage for such scenarios.
Is there a function module or series of FM's that are used to generate the E2EDKxxxxx type segments? I have been testing using the IDOC_OUTPUT_INVOIC and IDOC_OUTPUT_ORDRSP FM's, but they generate segments begining with E1EDKxxxxx.
Well, the E2* segments basically reflect the external name of the IDoc segment, whereas the function modules you're referring to basically just create an internal version of the IDoc. Once the IDoc framework then passes the IDocs to the partner, the segment names usually (depends on how the IDocs are passed on) get converted to their external name. If there are multiple versions of a segment, then the version number will be appended to the segment name.
Note that IDoc segment definitions are only partially stored in the data dictionary. If you want to see all versions you should always use transaction WE31 to look at segments. There you can also see for example for E1EDK01 the several versions and when you then use in SE37 function module SEGMENT_EXTERNAL_NAME_GET you will see what SAP produces as the external name for segment E1EDK01. This function module is basically the one that handles the segment name translations.
Ignore the comments for subsystem, this is basically an option in SAP to possibly trigger further external tools (e.g. mapping etc.) for handling the outbound IDocs.
Again, the funny thing is that via the WE30 transaction, if i put in INVOIC02 as the Obj. name and see the segments, i can see that E2EDK01 there is a version 005, but if i go to SE11 and put in E2EDK01005 structure line and i get a "not found". We just have up to E2EDK01002.
In the old days SAP used to generate E1, E2 and E3* structures in the data dictionary (SE11). The E1* structure reflected the character type representation of an IDoc segment, whereas the other two (definition and documentation) contained actual references to data elements (e.g. if you used a quantity field). However, in newer releases those dictionary structures (E2* & E3*) are no longer generated, because they're superfluous (meta data defined via WE31 is sufficient).
Cheers, harald

Help need my mac pro for school..it has Grey screen..spinning wheel...repaid disk ok...repair disk permission all repaired but one warning...

Help need my mac pro for school..it has Grey screen..spinning wheel...
I think I have mountain lion OS X....I have done I think almost every suggestion I've seen in discussion boards.
Boot in recovery repaired disk...ok...repair disk permission...all repaired but one warning...I've tried to reinstall lion (without losing data) and it Got all the way to one minute to be done and then the time change back two hours and kept doing this all night long. I haven't done a back up due to no external for time machine.
I hope someone can please help me I've been going crazy for a week now trying to figure this out. I use my computer for school and I'm currently very behind from in my school work thank you
Also I've checked my available space 424.91 free of 750 gigs....disk is verified

Welcome to the Apple Support Communities
Try holding the Shift key while your Mac is starting to start into safe mode. Then, after starting in safe mode, open Finder, select Go menu (on the menu bar) > Go to Folder, and type /Library/StartupItems. Then, empty this folder and restart the Mac.
If your Mac starts after doing this, it was a problem with a third-party app that starts automatically when you turn on the computer. It won't start automatically anymore after doing that

1941W configuration help needed

Our Deployment Scenario:-
1941W Gigabit Ethernet 0/0 is connected to the PPOE connection of the ISP.
Gigabit Ethernet 0/1 is connected to the wired LAN
I have created 2 wireless radio Cisco_Kamran_BGN which is operating at 2.4 Ghz Devices and Cisco_Kamran_A which is operating at 5Ghz Devices.
I have created 2 VLans for the Wireless.
Vlan 10 for Cisco_Kamran_A        192.168.10.x
Vlan 11 for Cisco _Kamran_BGN   192.168.11.X
The problem is the Wireless users are not getting the IP address from the respective DHCP server which has been configured on the Router.
Can please any from the community help me and show me where I am missing the configuration.
Please find my router & ap configuration below.
Router Configuration
Router#
sh run
Building configuration...
Current configuration : 3022 bytes
! No configuration change since last restart
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
enable secret 5 $1$TdQt$npYeaf/W0kRElcfMggzJ31
no aaa new-model
service-module wlan-ap 0 bootimage autonomous
no ipv6 cef
ip source-route
ip cef
ip dhcp excluded-address 192.168.1.1 192.168.1.50
ip dhcp excluded-address 192.168.10.1 192.168.10.10
ip dhcp excluded-address 192.168.11.1 192.168.11.10
ip dhcp pool DHCP
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 195.229.241.222 213.42.20.20
ip dhcp pool Cisco_Kamran_A
network 192.168.11.0 255.255.255.0
default-router 192.168.11.1
dns-server 195.229.241.222 213.42.20.20
ip dhcp pool Cisco_Kamran_BGN
network 192.168.10.0 255.255.255.0
default-router 192.168.10.1
dns-server 195.225.241.222 213.42.20.20
multilink bundle-name authenticated
crypto pki token default removal timeout 0
license udi pid CISCO1941W-E/K9 sn FCZ1553C1VK
hw-module ism 0
redundancy
bridge irb
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered GigabitEthernet0/0
arp timeout 0
no mop enabled
no mop sysid
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
interface Wlan-GigabitEthernet0/0
description Internal switch interface connecting to the embedded AP
switchport mode trunk
no ip address
interface Vlan1
no ip address
interface Vlan10
ip address 192.168.10.1 255.255.255.0
ip access-group DSL_ACCESSLIST in
ip nat inside
ip virtual-reassembly in
interface Vlan11
ip address 192.168.11.1 255.255.255.0
ip access-group DSL_ACCESSLIST in
ip nat inside
ip virtual-reassembly in
interface Dialer1
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
ppp authentication pap callin
ppp pap sent-username xxxxxx password 0 xxxxxx
ppp ipcp route default
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list DSL_ACCESSLIST interface Dialer1 overload
ip access-list extended DSL_ACCESSLIST
permit ip 192.168.0.0 0.0.255.255 any
control-plane
line con 0
password xxxxxx
login
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 67
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
password xxxxxx
login
transport input all
scheduler allocate 20000 1000
end
Router#
Router#
Router#
Access Point Configuration
ap#
ap#
ap#
sh run
Building configuration...
Current configuration : 2603 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
enable secret 5 $1$JxdQ$a2/00bWJuhUKP9QLC94YD/
no aaa new-model
dot11 syslog
dot11 ssid Cisco_Kamran_A
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 1045081417161C5A555C7A7B
dot11 ssid Cisco_Kamran_BGN
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 020D05561907017015165949
username Cisco password 7 14341B180F0B
bridge irb
interface Dot11Radio0
description 802.11bgn radio
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
broadcast-key change 3600
ssid Cisco_Kamran_BGN
antenna gain 0
station-role root
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface Dot11Radio1
description 802.11a radio
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid Cisco_Kamran_A
antenna gain 0
no dfs band block
channel dfs
station-role root
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
no ip address
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.10
description 802.11a bridge
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface GigabitEthernet0.11
description 802.11bgn bridge
encapsulation dot1Q 11
no ip route-cache
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
no activation-character
line vty 0 4
login local
end
ap#
ap#
ap#

Hi Stepehen,
Did the configuration as per your advice but i am getting the below mentioned error which i have highlighted it in red. Please advice what needs to be done.
Home
Re: 1941W configuration help needed
created by Stephen Rodriguez in Getting     Started with Wireless - View the full discussion
conf t
interface     Dot11Radio0
no ssid     Cisco_Kamran_BGN
no encryption mode     ciphers aes-ccm
exit
interface     Dot11Radio1
no encryption mode     ciphers aes-ccm
no ssid     Cisco_Kamran_A
exit
dot11 ssid     Cisco_Kamran_A
vlan 10
dot11 ssid     Cisco_Kamran_BGN
vlan 11
exit
interface     Dot11Radio0
encryption vlan 11     mode ciphers aes
ssid     Cisco_Kamran_BGN
exit
interface     dot11radio0.1
encapsulation     dot1q 1 native
bridge-group 1
interface     dot11radio 0.11
encapsulation     dot1q 11
bridge-group 11
Configuration of     subinterfaces and main interface
within the same bridge     group is not permitted
exit
interface     Dot11Radio1
encryption vlan 10     mode ciphers aes-ccm
ssid     Cisco_Kamran_A
interface     dot11radio1.1
encapsulation     dot1q 1 native
bridge-group 1
interface     dot11radio1.10
encapuslation     dot1q 10
bridge-group 10
Configuration of subinterfaces and main     interface
within the same bridge     group is not permitted
end
wr
Reply to this message by going to Home
Start a new discussion in Getting Started with Wireless at Home

ONKYO TX-SR805 Set-up Menu HELP Needed

This is a LONG post, but I would appreciate if you would read it and respond to it. The settings That are setup might not be the CORRECT settings. If you think a different setting should be made, please let me know.
Also right now I only have 2 front speakers (NHT VT-1A), 1 middle( NHT VT-1C), and a NHT SW12 Subwoofer. I will be hooking up 2 or 4 more speakers for the REAR.
Here are the settings on my TX-SR805 receiver on the set-up menu. I could use some help to see if they need set to something else.
2.2 Speaker Config
      Subwoofer       yes
      Front            70Hz
      Center          90Hz
LPF of LFE        80Hz THX
2.6 THX Audio Setup
       THX subwoofer YES   I don't know if mine is or not
       BGC                    OFF Not sure what this BGC means
3. AUDIO ADJUST
3.1 Tone Control
       Front    Bass      -1dB
                    Treble   +1dB
      Center Base      +2dB
                    Treble   +7db
     Subwoofer Base +7
3.2 DIRECT
      Delay Enable
      DSD                NO   Not sure what DSD is
3.3 MULTIPLEX/MONO
      Multiplex
      Input CH       Main/Sub
      Mono
      Input CH         L+R
      Output Speaker L/R
3.4 PLIIx/Neo:6
        PLIIx Music   (2ch input)
        Panorama        ON
        Dimension       +1
        Center Width    3
Neo: 6 Music
        Center Image   5
3.5 DOLBY EX
        Dolby EX        AUTO
3.6 THEATER-DIMENSIONAL
        Listening Angle   Narrow
3.7 LFE LEVEL
        Dolby Digital      -10dB
        DTS                     -10dB
        Multich PCM      -10dB
        Dolby True HD   -10dB
        DTS-HD Master Audio -10dB
        DSD                     -10dB
4. SOURCE SETUP
       CABLE/SAT
4.1 INTELLIVOLUME     +4Db
   .2 A/V SYNC            0 msec
   .3 NAME EDIT         Blank
5.   LISTENING MODE PRESET
5.1 DVD
       Analog/PCM      NOT SURE WHAT TO SET HERE
       Dolby Digital      NOT SURE WHAT TO PUT HERE
       NOT SURE WHAT TO PUT FOR ANY OF THESE LISTENING MODE PRESET
5.8 TUNER (ANALOG)      Neural THX 5.1 is set on mine. Is this correct?
         CD                           ?
6. MISCELLANEOUS
6. 1 VOLUME SETUP
          Volume Display              Relative
           Muting Level               -40dB
           Maximum Volume       +10dB
           Power on Volume        -22dB
           Headphone Level        +2dB
6.2 OSD SETUP
           Immediate Display       OFF
           Monitor Type              16:9
           Display Position           TOP
7. HARDWARE SETUP
7.4   ANALOG MULTICH
           Subwoofer Input Sensitivity    0
7.5   HDMI
        ALL under here are     ENABLE
Solved!
Go to Solution.

I gave you some answers in your original post. I wish you didn't start a new one. Here is what I posted.
Re: ONKYO TX-SR805 Set-up HELP Needed[ New ]
Options
Mark as New
Bookmark
Subscribe
Subscribe to RSS Feed
Highlight
Print
Email to a Friend
Report Inappropriate Content
01-21-2010 08:24 AM
Unfortunately this is very difficult because the top half of your post, your really the only one that can answer what the setup should be. The adjustments are made based on the acoustics of your room and how everything sounds noone can really give you info on it because every house, and room has different acoustics. The walls, insulation, carpet or bare floors, basement or main floor are just some examples of what can make a difference in sound reproduction.   By the way NHT (Now Hear This) are excellent speakers. For bass and treble, the music I listen too requires a high treble content so I usually have it at 7 out of 10 but my bass is at 4 out of 10.   The sub base should be fine where it is.
Did your receiver come with an Audessy mic for calibration. I would use that for a basic setup and go from there I am not sure if on your unit it will do frequecy but I think it did.
Your volume settings look fine again personal preference there is right or wrong.
For you listening mode Preset you should have an auto setting I am at work so it may take a coule of hours for me to get back to you as I have to go through your manual and see what you would set it up with so please bare with me. I will list the info as I read it so it may not be in the order you have it.
I will have to make a second post since I can't go back and edit this one.

Help Needed for T42 Start-up Problem

Urgent help need!!!
I have a ThinkPad T42 with Windows XP installed. It works perfectly for a while without ever have any problem or error message. Then suddenly it won’t work anymore. The symptom is following:
After power on the laptop the Microsoft window would show up and it prompt me for window logon password. After I type in the password it then shows “window is loading your personal setting”. After a long while nothing would show up on the screen other than the background of the normal screen. There is no window bar at the bottom or any icon on the screen. If I start in safe mode then everything would show up. I don’t know what is going on.
This happened two months ago and I ended up restoring a backup image to get it work again. It happens again today with the same symptom. I am really tired of having to restore image backup every 2 months.
I would really appreciate it if any of your experts can offer me some insight into this problem. I am desperate in need of help.
Thanks very much!

wangy26, welcome to the forum,
Have a look at this thread to see if my post there helps. The problem seems to mostly occur at the start of a month, why I don't know. Unfortunately the member didin't report back whether or not this was a viable solution for them.
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

Help Needed - Even after lodging "Presidential Complaint"

Help needed please!!To make a long story short I have been through nothing but aggravation the past week trying to get my phone working. Service call on 7/6 to install Fios Internet, TV and phone. Internet and TV work fine, but Phone has no dial tone, going on a week and a half now. Tried contacting the account rep who set up my account, her supervisor as well as tech support on numerous occassions.
They set a dispatch for yesterday, and when the tech called me to say he was here, he was at an address i moved out of 4 years ago, in another state.I get a call from someone saying the service request was being closed and I need to call in with the correct address, after telling that rep I would not do that, that Verizon should make the updates based on my TV/Internet records, she hung up on me. Called back into Tech Support and the best they could do was an appointment for tomorrow. I then called the Corporate number and spoke with someone who opened a "Presidential Complaint" and requested an expedited call.. well i have heard nothing since then other than an automated call earlier today sayin my original service request will be kept. Needless to say I'm very upset that after a week and a half I still have no phone service and it doesn't seem like anyone is real willing to help me. I'm sure I'll get billed in full even though one of the 3 services I'm paying for hasn't been working in a week and a half..

Hi jkoen77,
Your issue has been escalated to a Verizon agent. Before the agent can begin assisting you, they will need to collect further information from you. Please go to your profile page for the forum and look at the top of the middle column where you will find an area titled "My Support Cases". You can reach your profile page by clicking on your name beside your post, or at the top left of this page underneath the title of the board.
Under "My Support Cases" you will find a link to the private board where you and the agent may exchange information. The title of your post is the link. This should be checked on a frequent basis, as the agent may be waiting for information from you before they can proceed with any actions. To ensure you know when they have responded to you, at the top of your support case there is a drop down menu for support case options. Open that and choose "subscribe". Please keep all correspondence regarding your issue in the private support portal.

Driver Help Needed

Hey guys, I did a lot of reading and tried many things before actually seeking for help. Long story short I re-installed Windows XP Home edition on an old computer of mine, now that I have reformatted, I have windows XP home edition installed but I can't get any drivers that I need because I'm unable to get on the internet. The reason being is that I don't have the driver for my Network Adapter.
What I have is:
MSI N1996
Model name: MS 7125 ver 1
Model Number: K8N Neo 4
I have searched and searched and I found a lot of people also had this problem but I can't find my resolution. I am guessing that it is the driver that I need.
Internet was working fine prior to formatting, I have checked My Computer-Properties- Device Manager... and what has the yellow "?" are:
-Multimedia Controller
-Multimedia Controller
-Other PCI Bridge Device
-PCI Memory Controller
-SM Bus Controller
-Video Controller (VGA Compatible)
My ethernet chord lights up once plugged into the computer but that's it.
If anyone knows of where I could find a driver for it that would be greatly appreciated. If you need any more info I can try to find it out, I'm on a laptop on my wireless now.

Quote
Model name: MS 7125 ver 1
Model Number: K8N Neo 4
Which K8N Neo4 board exactly do you have?
The Neo4 Platinum v1 board has two network ports, one controlled by an additional Marvell LAN chipset.
Do you have one, or two LAN ports? If two, plug the ethernet cable into the other port.

How can I transfer music from my ipod classic 60GB to my iPhone 4 music library, just by song or whole CD that I have bought? Help needed!

How can I transfer music from my ipod classic 60GB to my iPhone 4 music library, just by song or whole CD that I have bought? Help needed!

load the current version of I tunes on the laptop and sync the pod. Then sync the phone - you can select all or as much of the music you want to.
Also - if the music on the pod was purchased from the itune store in the first place, you should be able to redownload it to the phone for free, as long as you are using the same apple id that it was bought with.

IE needs longer to load using Dynadock V10 on Satellite Pro M70

Hi,
when I'm using the Dynadock V10 on the Sattelite Pro M70 every time when a program has pictures in it, the need long time to load, and for this time the mouse curser is jumping. It appears in MS Internet Explorer as well as in MS Word.
Is there maybe a bottleneck with all those different data coming throw one simple USB cable?
When I don't use the Dynadock, connecting all the different cables directly with the Sattelite Pro the error doesn't happen!
Grafik driver is on the newest realease and the Operating System Windows XP has SP3 and newest Updates!
I tried to deinstall the Dynadoc Software, but the problem still occures.
How can I fix the problem, because now working is so bad, that the Dynadoc doesn't make sense!
Thanks in Advance!

I dont think anyone here will be able to offer some logic explanation and I think you must search best combination how to connect all devices together to have best performance.
We can ask here so many stuff but if this will help.... I dont think so.
What Im interesting here is follow: have you tried to change devices connectivity to get best performance? For instance I would never connect LAN to the Dynadock.
Why to send signal to external device and not directly to the notebook?

Upon upgrading iPhoto, iPhoto Help no longer works. It gives the error message: "The selected topic is currently unavailable. To see all iPhoto Help, you must be connected to the Internet." Help!?

Upon upgrading iPhoto, iPhoto Help no longer works. It gives the error message: "The selected topic is currently unavailable. To see all iPhoto Help, you must be connected to the Internet." I am obviously connected to the internet since you are reading this.
I tried upgrading permissions but it did not help!? Can anyone tell me what is wrong? Thanks

Try
Reboot the computer, see if that fixes it.
Then try:
Backup your files off the computer (not TimeMachine) and disconnect
Hold c boot off the 10.6 disk and simply reinstalling OS X
Log in and update to 10.6.8
c boot off the 10.6 disk again and use Disk Utility >Repair Disk
reboot and all should be fine, except some third party programs that install kext files, those will have to be reinstalled from fresh sources.

Compaq Multiport Evo n800c wlan help needed(long)

Similar Messages

Maybe you are looking for