Connect to an existing phone system

Our church currently has two regular phone lines connected to an in-house system. I would like to replace the second line with a Skype line. Can I connect to my existing phone system? Both lines currently just plug into the system. How do I convert Skype to a wired line? Are there monthly costs? Per minute usage costs? I am very new to all of this and would love some guidance. I don't really even know where to begin. Thanks

Hi Jamie,
In order to help you I need some more information:
Can you tell me what your remote system is?
What is consists of? eg PXI 1000 chassis with specific modules?
What are you trying to communicate with it from? - a local PC?
Is the system hardware NI or third party?
What operating system are you using? eg Windows XP?
Have you installed the drivers for the hardware? Did you remember to install the drivers after you had installed the hardware and reboot?
Did you get the found new hardware wizard popup when you installed the hardware?
What are the methods you have already tried for connecting to it?
In what way are you communicating between your local and remote system?
ie via Serial port? TCP communication?
Regards
Emma Rogulska
NIUK & Ireland

Similar Messages

How to prioritise connection of CAR Bluetooth PHONE system/ device over SmartBand Talk SWR30

After pondering about this device for over a month I asked my wife to gift it me for Christmas. For 3 days I really liked it, but then a critical flaw became apparent Having not driven for a few days due to the holidays I set off in my car, only to realise that I was not receiving telephone calls, SMS and other notifications on my built-in car bluetooth system (Ford Sync by Sony/ Microsoft), only on the Smartband Talk. Doing some research it became clear that if my SWR30 was already connected with my Xperia (Z2) my Ford Sync could not connect! I realise the limitations of Bluetooth (i.e. you cannot have simultaneous connections using a same Bluetooth profile) and the workaround is to manually turn off the Phone Audio (handsfree) Bluetooth profile for SWR30 in the Z2. Remembering to turn off/ back on is proving to be irritating and too much effort. I thought I might be able to create an Event (macro) in Sony's Smart Connect app to do this automatically, but this cannot be done as the app is rather limiting! It is more important for my car system to work with my Z2 as I use it frequently and is altogether a safer and more legal way of answering calls etc. Has any one got ideas or suggestions? I really like this SmartBand (its far sleeker & lighter than true smartwatches) and I actually want the talk feature, but if I cannot resolve the car bluetooth problem (and this will probably affect all other Bluetooth car systems/ devices) easily and smoothly, regretfully, the SWR30 will be going back to the seller

As stated before, I really like the SmartBand Talk and was very disappointed to learn that it could not coexist with a car Bluetooth system! Having had a few days off between Christmas and New Year I was determined to resolve this "flaw" and am glad to report that I have and in a slick way! Prompted by "ensaro's" widget suggestion, unfortunately I did not want a toggle which had to be manually executed, it had to be automatic. So I thoroughly researched the Google Play Store, trying out many, and ended up with 2 apps which were real contenders: Trigger (by Egomotion) and Automagic (by Gridvision). Both apps basically allow you to create a trigger (eg Bluetooth Car Audio wants to connect to phone) followed by an action (eg switch off Bluetooth phone connection to SmartBand, followed by switch on connection to Bluetooth Car Audio). Trigger calls this automation task a Trigger, Automagic calls it a Flow.Trigger is fairly intuitive visually, but unfortunately support for this supposedly highly rated app seems no longer to exist! This became very frustrating for me as at times it would not run (however, it also allows a widget to be created to manually run the task manually)... therefore I dug in to the more heavyweight Automagic! Automagic uses a dynamic flowchart, where you add a trigger, an optional condition (true/ false) and finally action(s). The style reminded me of my programing days many years ago and the logical nature excited me. The possibilities are huge and may scare off some users looking for a quick result, but in fact it is really quite easy to use, especially once you undertstand some of the slightly "obscure" terminology used (after all this a German programer at work and some translation suggestions may be required). At the end of the day I created 2 flows, one to connect to the car system (via disconnection of SmartBand and then connection to my car) and one to reconnect to the SmartBand when not in car (the trigger being that the car Bluetooth is no longer connected/ disconnected). These flows are passive and apparently use very little battery power, executing when a trigger condition is matched and so far is working well. If anyone wants to see how my flows are constructed, I will be happy to email them. You open them up directly in Automagic (going to their site allows you to download a 9 day trial with up to 3 flows working)... my flows are embellished with extra actions, such as switching off WiFi and playing a sound when a connection has taken place... and most important of all there is a forum with lots of help and examples and I was really happy when the progaming author, Martin, actually replied to a query... Problem... sorted! Automagic is well worth £2.40 ...

Table does not exist in system after DB Connect

Hi Everyone,
I must extract data from a oracle db. I create a source system with DB Connect and it's connect successful.
Later, i create a datasource for that source system. but it show the table does not exist in system. I'm sure the table is correct. why?
Thanks!

Check the schema names & ensure it is with the same owner/name as in the DB source table/view. You can also use a simple lookup table which checks table/views in your schema from other standard tables.

Cannot connect to the phone system. An unidentified error has occurred, Please try again.

Issue: Lync 2013 users with remote call control enabled cannot connect to the phone system. When the user logs into Lync, they see an exclamation in the bottom right corner
with this error.
Error: Cannot connect to the phone system. An unidentified error has occurred, Please try again. If the problem continues, please contact your support team.
Environment:
1 site: Site1
2 Pools:
1. Lync 2010
Trusted application is added here for the site.
2. Lync 2013
Avaya phone system: AES r6-1-2-32-0
I have not moved the trusted application to the Lync 2013 pool yet, but my understanding is that it should still work since it’s in the site. Is my understanding on this correct? (All of my other trusted applications do work for Lync 2013
users & none of them have been moved yet. Remote Call Control is the only one that does not work.)
This is from the uccapi log. This is just from the user logging in, not actually making a call. Below are the items that I think are important, however, I don’t know how to interpret it to determine if the problem is on the Lync side or
the Avaya side. Here’s a summary:
SIP/2.0 100 Trying
Authentication-Info: TLS-DSK qop="auth", opaque="5FD217E1", srand="E05700E2", snum="9", rspauth="f308eae87c0bbe64a1ab213574776cbdf9823ab6", targetname="lync03.domain.com",
realm="SIP Communications Service", version=4
From: <sip:[email protected]>;tag=bbb282ebbd;epid=a86d5b0a29
To: <sip:[email protected]>
Call-ID: 9eb0d23a3b8f4e0eafc6c6da622fbecf
CSeq: 1 INVITE
Via: SIP/2.0/TLS 10.155.48.96:61472;ms-received-port=61472;ms-received-cid=1FA400
Server: http%3A%2F%2Fwww.microsoft.com%2FLCS%2FUdcAgent
Content-Length: 0
SIP/2.0 200 OK
Authentication-Info: TLS-DSK qop="auth", opaque="5FD217E1", srand="15C0F9A2", snum="13", rspauth="4fd891e39a33e902fb1cec5d980e5bf0ccb172a0", targetname="lync03.domain.com",
realm="SIP Communications Service", version=4
From: <sip:[email protected]
>;tag=bbb282ebbd;epid=a86d5b0a29
To: <sip:[email protected]
>;tag=A7A45C856ECD79121A1827265ABBD7F6
Call-ID: 9eb0d23a3b8f4e0eafc6c6da622fbecf
CSeq: 1 CANCEL
Via: SIP/2.0/TLS 10.155.48.96:61472;ms-received-port=61472;ms-received-cid=1FA400
Server: http%3A%2F%2Fwww.microsoft.com%2FLCS%2FUdcAgent
Content-Length: 0
SIP/2.0 487 Request terminated
Authentication-Info: TLS-DSK qop="auth", opaque="5FD217E1", srand="F46EC133", snum="14", rspauth="1d92718caa4f61d967faa46a5c256aafa8b4e740", targetname="lync03.domain.com",
realm="SIP Communications Service", version=4
From: <sip:[email protected]
>;tag=bbb282ebbd;epid=a86d5b0a29
To: <sip:[email protected]
>;tag=A7A45C856ECD79121A1827265ABBD7F6
Call-ID: 9eb0d23a3b8f4e0eafc6c6da622fbecf
CSeq: 1 INVITE
Via: SIP/2.0/TLS 10.155.48.96:61472;ms-received-port=61472;ms-received-cid=1FA400
ms-diagnostics: 5002;reason="Request was cancelled";AppUri="http%3A%2F%2Fwww.microsoft.com%2FLCS%2FUdcAgent";source="lync03.
domain.com"
Server: http%3A%2F%2Fwww.microsoft.com%2FLCS%2FUdcAgent
Content-Length: 0

Hi Suelizy,
To better understand the issue, I would like to collect the following information for troubleshooting:
1. Do you mean the Lync 2010 user can connect to the Phone System?
2. What’s next hop pool of the application?
In a mixed environment, you must set the next hop pool to be the Lync Server 2013 pool.
Best regards,
Eric

My iPhone 6plus will no longer connect to my Dodge UConnect system. Phone calls get a beep "phone call completed" message. Music will play though. Just can't make calls. Tried turning off iCloud and repairing but nothing works. It did work a few days

My iPhone 6plus will no longer connect to my Dodge UConnect system. Phone calls get a beep "phone call completed" message. Music will play though. Just can't make calls. Tried turning off iCloud and repairing but nothing works. It did work a few days

Hi Jpcbew,
The article linked below provides a lot of great information and troubleshooting tips that can help you resolve the issue with your iPhone 6 Plus connecting to you car stereo system.
Get help using your iPhone, iPad, or iPod touch with your car stereo - Apple Support
So long,
-Jason

I can't connect to Wi-Fi - keeps timing out. No problem connecting from other laptops / phones. Stopped working after I did a system upgrade. What can I do?

I can't connect to Wi-Fi - keeps timing out. No problem connecting from other laptops / phones. Stopped working after I did a system upgrade. What can I do? I am on OS X Yosemite.

Take each of the following steps that you haven't already tried, until the problem is resolved. Some of these steps are only possible if you have control over the wireless router.
Step 1
Turn Wi-Fi off and back on.
Step 2
Restart the router and the computer. Many problems are solved that way.
Step 3
Change the name of the wireless network, if applicable, to eliminate any characters other than letters and digits. You do that on your router via its web page, if it's not an Apple device, or via AirPort Utility, if it is an Apple device.
Step 4
Run the Network Diagnostics assistant.
Step 5
In OS X 10.8.4 or later, run Wireless Diagnostics and fix the issues listed in the Summary, if any.
Step 6
Back up all data before proceeding.
Launch the Keychain Access application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
Enter the name of your wireless network in the search box. You should have one or more "AirPort network password" items with that name. Make a note of the name and password, then delete all the items. Quit Keychain Access. Turn Wi-Fi off and then back on. Reconnect to the network.
Step 7
You may need to change other settings on the router. See the guidelines linked below:
Recommended settings for Wi-Fi routers and access points
Potential sources of interference
Step 8
Make a note of all your settings for Wi-Fi in the Network preference pane, then delete the connection from the connection list and recreate it with the same settings. You do this by clicking the plus-sign icon below the connection list, and selecting Wi-Fi as the interface in the sheet that opens. Select Join other network from the Network Name menu, then select your network. Enter the password when prompted and save it in the keychain.
Step 9
Reset the System Management Controller (SMC).

Connecting Shuffle to phone system and dock

A friend of mine who works for a local non profit outfit wants to use an mp3 player to provide music for her voice mail system. She's considering a shuffle, but she wants the music playing 24/7, literally all the time. You can't simultaneously connect a shuffle to headphones (or other similar speaker) and the charger. Is there a dock that will let her keep the shuffle docked/charging while simultaneously playing music into her phone system?

Sorry, but the answer is NO.

Error: No Phone System Connection

Greetings,
I am integrating RCC with Lync 2013 and I am getting this
Notification: No Phone System Connection. I have notices that when I capture packets transferred between Front End Server and CUPS server, there are no packets being sent to CUPS server.
I have completed below steps:
1) I have enabled integration with my phone integration option in Lync client
2) Added Static route to the CUPS server on port 5060.
3) Added CUPS as a trusted application in the application pool.
4) Published the new topology and restarted the Front End Services.
Remote Call Control URI is set to: sip:[email protected]
Phone URI is set to XXXX;phone-context=dialstring
I would really appreciate if you can guide me.
Thank you
Chirag
Chirag Shah

Hi,
Did the Lync account contains an apostrophe? If so, it may influence for the users with an apostrophe (') in their Lync sign-in ID. In order to resolve the issue, remove the apostrophe from the Lync sign-in ID. Also you can change to use another Lync account
to have a test.
You can refer to the part of “Unable to get Softphone control” in the link below:
http://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-presence/97443-cups-cupc-ts.html#controlerror
Note: Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information found there. Please make
sure that you completely understand the risk before retrieving any suggestions from the above link.
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support

Windows Phone Emulator is unable to connect to the Windows Phone operating system: The phone did not respond to the connect request. Some functionality might be disabled

We are receiving following error, while trying to deploy the application on Win Phone emulator. “Windows Phone Emulator is unable to connect to the Windows Phone operating system: The phone did not respond to the connect
request. Some functionality might be disabled.”
I have tried all possible ways that we found on blogs. We are still not able to solve this issue

I have had a lot of issues with the emulator in the past.
Check out this troubleshooting guide. It might help:
https://msdn.microsoft.com/en-us/library/windows/apps/jj681694(v=vs.105).aspx
Also, I find that if I cancel my build/deploy while it is stuck on booting the OS and then wait a short while the phone OS will complete booting, and from that point I can deploy to the emulator. It's a workaround, but it works well for me.
I need to do that on Windows 10 tech preview, which may or may not be simply an incompatibility with the beta OS.
I'm a self-taught noob amateur. Please take this into account when responding to my posts or when taking advice from me.

Just got the Iphone 6 and it paired BT with the car phone system okay. But it will not pair with the audio part where I could play my recorded music with my 5-C. The system will not connect with the phone and the message is that the settings

My toyota Seinna 2011 refuses to connect with my Iphone 6 as a "portable player". Message says for me to adjust the player. On the phone it is searching for other devices but not connecting. Now same phone is paired with the car multimedia system and will take and make calls. Help!

I very much doubt it if you consider how much data Apple release to App developers
to allow them to create apps that work under iOS
Audi being lazy like most of the other motor manufacturers
They will be registered developers and as such get all the info and data they need

Trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?

I am trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?
The Apple update Firmware for my Airport Extreme Base Station does not update for some reason? Help?
Additionally, I have an older version Airport Express that does not update with the newer Airport Utility Version 6.3 and asks me to download 5.6 to update? Is this worth it?
Thanks

The netgear is not going to work very well.. and not at all unless it is universal wireless extender.. you cannot use WDS method.
If it does support universal wireless then make sure the airport uses a rational SMB compatible wireless name.. not an apple name which is 35 characters long with spaces and illegal characters like apostrophe.
So nice AE name.. AEwifi and actually while you are trying.. fruitlessly to do this.. use AE24ghz and AE5ghz (so different names on the different bands)
Assuming your AE is gen3 or greater.
You should also fix the wireless channel at least for 2.4ghz since the netgear is probably only going to repeat 2.4ghz so use channel 11, as a trial.
And use no wireless security as a test.. if that works.. then use WPA1 & 2.. as often old equipment using WPA2 is not compatible.
If it fails with simple name.. fixed channel and no security. Sorry it is not compatible at all.. it happens.
If your AE is G wireless or earlier model.. really the time has come for replacement.
If your Express is G wireless model it is not supported.. and is too old to bother with expect I guess if you want to run audio to a speaker.
You must use older 5.6 utility to do this.. so do you have a computer running older OS.. up to Mountain Lion it is easy to install with a bit of manipulation.. later is much harder .. or windows computer anywhere or available to you.

We bought a new prepaid phone on 10/5/14 at a Verizon store had an existing phone number transfered and the phone can not be activate. When will the system be updated? We have lost 2 days of service.

We bought a new prepaid phone on 10/5/14 at a Verizon store. Had an existing phone number transfered and the phone can not be activatde. When will the system be updated? We have lost 2 days of service and now cannot use the original phone due to moving service to Verizon.

The exact same thing has happened to me! The customer service reps keep saying there is nothing they can do until their system upgrades are complete and they can't tell me when that will be! I need my phone number back!!! Somebody please help with this issue!

Automatic connection between call center and phone system

Dear friends,
I have one customer, they have a phone system in their call center.
When implemeting CRM 2007, they want to have an automatic connection betwwen their phone system and call center in CRM. This means when having a call from customers the call center system ( CRM 2007) searches automatically or updates the phone number ( this phone number is get automatically from phone system ).
Does this is possible in CRM 2007? Or if u have any solutions pls let me know.
Thanks and Regards,
Nghi Do

Hi,
Just check if this blog is of any use to you:
What is Computer Telephony Integration (and Why Do I Need It?)
Thanks and Regards,
Rohit

PAP2T connection to phone system?

Has anyone connected a PAP2T adapter to a multi-line phone system. Using Viatalk, can't seem to get enough power to have both lines functional when hooked to analog Telrad 8/16 KeyBx. Both lines work fine when connected to single line telephones. HELP!!!! Reid McAuley, Rocky Mount Habitat for Humanity

Solved problem!!! PAP2T must be within 6 feet of telephone system. Moving it closer and using short telephone base cord solved the problem. Both lines now working on the system.

Adding Answerphone to existing phones

I have 3 BT Graphic 2100 phones. I would like to add a Freelance XD 8500 Answerphone to the system, perhaps making the 8500 the base unit, is this possible?

Because my handsets didn't register correctly, and kept showing No Line, I changed the Answerphone for a BT4500. I successfully registered the Graphite handsets, and they show the correct Handset number now. The only thing that surprised me was that the BT4500 wouldn't connect using my existing telephone cable, but if I use the one supplied it works fine, even though both cables look the same and my original one works with other base units. I am not sure what I will do if anything happens to the phone cable supplied with the BT4500 if other cables don't work with it. I always thought that telephone cables were the same, the fittings on the ends are the same.

Connect to an existing phone system

Similar Messages

Maybe you are looking for