CSCul38768 - Management services are unresponsive fault seen

Our UCS hit this bug and we found the VM hosted on each blade got timeout also. It caused some of the VM rebooted and vCenter reported shared disk cannot access during the captioned moment.
Did anyone have similar experience before?

Padma,
TAC Engineer sent below mail
Hi Amit,
I’ve checked through the show tech you’ve uploaded and have not found any indicators of errors for the error message you are seeing.
As I mentioned in the call, the error is a transient error from which the fabric interconnects can automatically recover from. The recommended action is to wait for a few (10-15min) to see if the error clears automatically. If the error does not clear then we will need to do further troubleshooting. This error on its own is not a cause for worry. As you have HA in your system the management services would have failed over the to the other fabric interconnect and would not affect your system performance.
We can leave the system under observation for a few days to see if other errors occur concurrently with this error.
I will upload show-tech logs here, find my reply below
Is the alert generated only for FI B or both FIs ->> Amit: Alert generated for FI-B only
Any change in cluster state corresponding to alert time stamp ->> Amit: Unfortunately when this error generating we are unable to see the cluster state because of timing. If you can guide / suggest from any other location I can find the state that will be helpful
Cluster physical link status ->> Amit: Cluster link is OK
Does FI have any core dumps ->> Amit: I don't have any idea about this. How can check this ?
Regards,
Amit Vyas

Similar Messages

Fabric Interconnect B, management services are unresponsive

Hi,
We have configured Call Home option in UCSM and we are getting below error from Call Home option since last Saturday. We have open TAC with Cisco to troubleshoot this error but as per TAC "The error is a transient error from which the fabric interconnects can automatically recover."
Below is the error messages we are getting
E-mail-1:
Subject:
System Notification from System-A - diagnostic:GOLD-major - 2011-12-27 17:54:09 GMT-00:00 Fabric Interconnect B, management services are unresponsive
Body Message:
System Name:System-A
Time of Event:2011-12-27 17:54:09 GMT-00:00
Event Description:Fabric Interconnect B, management services are unresponsive
Severity Level:6
E-mail-2:
Subject:
System Notification from System-A - diagnostic:GOLD-major - 2011-12-27 17:54:09 GMT-00:00 Fabric Interconnect B, management services are unresponsive
Body Message:
<?xml version="1.0" encoding="UTF-8" ?>
<soap-env:Envelope xmlns:soap-env="http://www.w3.org/2003/05/soap-envelope">
<soap-env:Header>
<aml-session:Session xmlns:aml-session="http://www.cisco.com/2004/01/aml-session" soap-env:mustUnderstand="true" soap-env:role="http://www.w3.org/2003/05/soap-envelope/role/next">
<aml-session:To>http://tools.cisco.com/neddce/services/DDCEService</aml-session:To>
<aml-session:Path>
<aml-session:Via>http://www.cisco.com/appliance/uri</aml-session:Via>
</aml-session:Path>
<aml-session:From>http://www.cisco.com/appliance/uri</aml-session:From>
<aml-session:MessageId>1058:SSI1442BFRC:4EFA0641</aml-session:MessageId>
</aml-session:Session>
</soap-env:Header>
<soap-env:Body>
<aml-block:Block xmlns:aml-block="http://www.cisco.com/2004/01/aml-block">
<aml-block:Header>
<aml-block:Type>http://www.cisco.com/2005/05/callhome/diagnostic</aml-block:Type>
<aml-block:CreationDate>2011-12-27 17:54:09 GMT-00:00</aml-block:CreationDate>
<aml-block:Builder>
<aml-block:Name>UCS 6100 Series Fabric Interconnect</aml-block:Name>
<aml-block:Version>4.2(1)N1(1.43q)</aml-block:Version>
</aml-block:Builder>
<aml-block:BlockGroup>
<aml-block:GroupId>1059:Serial Number:4EFA0641</aml-block:GroupId>
<aml-block:Number>0</aml-block:Number>
<aml-block:IsLast>true</aml-block:IsLast>
<aml-block:IsPrimary>true</aml-block:IsPrimary>
<aml-block:WaitForPrimary>false</aml-block:WaitForPrimary>
</aml-block:BlockGroup>
<aml-block:Severity>6</aml-block:Severity>
</aml-block:Header>
<aml-block:Content>
<ch:CallHome xmlns:ch="http://www.cisco.com/2005/05/callhome" version="1.0">
<ch:EventTime>2011-12-27 17:54:09 GMT-00:00</ch:EventTime>
<ch:MessageDescription>Fabric Interconnect B, management services are unresponsive</ch:MessageDescription>
<ch:Event>
<ch:Type>diagnostic</ch:Type>
<ch:SubType>GOLD-major</ch:SubType>
<ch:Brand>Cisco</ch:Brand>
<ch:Series>UCS 6100 Series Fabric Interconnect</ch:Series>
</ch:Event>
<ch:CustomerData>
<ch:UserData>
<ch:Email>[email protected]</ch:Email>
</ch:UserData>
<ch:ContractData>
<ch:CustomerId>[email protected]</ch:CustomerId>
<ch:ContractId>ContractID</ch:ContractId>
<ch:DeviceId>N10-S6100@C@SSI1442BFRC</ch:DeviceId>
</ch:ContractData>
<ch:SystemInfo>
<ch:Name>System-A</ch:Name>
<ch:Contact>Name</ch:Contact>
<ch:ContactEmail>[email protected]</ch:ContactEmail>
<ch:ContactPhoneNumber>+00-0000000000</ch:ContactPhoneNumber>
<ch:StreetAddress>Office Address</ch:StreetAddress>
</ch:SystemInfo>
</ch:CustomerData>
<ch:Device>
<rme:Chassis xmlns:rme="http://www.cisco.com/rme/4.0">
<rme:Model>N10-S6100</rme:Model>
<rme:HardwareVersion>0.0</rme:HardwareVersion>
<rme:SerialNumber>SerialNumber</rme:SerialNumber>
</rme:Chassis>
</ch:Device>
</ch:CallHome>
</aml-block:Content>
<aml-block:Attachments>
<aml-block:Attachment type="inline">
<aml-block:Name>sam_content_file</aml-block:Name>
<aml-block:Data encoding="plain">
<![CDATA[
<faultInst
ack="no"
cause="management-services-unresponsive"
changeSet=""
code="F0452"
created="2011-12-27T23:24:09.681"
descr="Fabric Interconnect B, management services are unresponsive"
dn="sys/mgmt-entity-B/fault-F0452"
highestSeverity="critical"
id="2036245"
lastTransition="2011-12-27T23:24:09.681"
lc=""
occur="1"
origSeverity="critical"
prevSeverity="critical"
rule="mgmt-entity-management-services-unresponsive"
severity="critical"
status="created"
tags=""
type="management"/>]]>
</aml-block:Data>
</aml-block:Attachment>
</aml-block:Attachments>
</aml-block:Block>
</soap-env:Body>
</soap-env:Envelope>
We want to understand that what is the impact of this error and is there anything that we can do to prevent this error? Also want to know what might be the cause get this error?
Let me know if anything else is needed from my side
show-tech file uploaded.

Padma,
TAC Engineer sent below mail
Hi Amit,
I’ve checked through the show tech you’ve uploaded and have not found any indicators of errors for the error message you are seeing.
As I mentioned in the call, the error is a transient error from which the fabric interconnects can automatically recover from. The recommended action is to wait for a few (10-15min) to see if the error clears automatically. If the error does not clear then we will need to do further troubleshooting. This error on its own is not a cause for worry. As you have HA in your system the management services would have failed over the to the other fabric interconnect and would not affect your system performance.
We can leave the system under observation for a few days to see if other errors occur concurrently with this error.
I will upload show-tech logs here, find my reply below
Is the alert generated only for FI B or both FIs ->> Amit: Alert generated for FI-B only
Any change in cluster state corresponding to alert time stamp ->> Amit: Unfortunately when this error generating we are unable to see the cluster state because of timing. If you can guide / suggest from any other location I can find the state that will be helpful
Cluster physical link status ->> Amit: Cluster link is OK
Does FI have any core dumps ->> Amit: I don't have any idea about this. How can check this ?
Regards,
Amit Vyas

UCCX Application manager service are in partial

After upgrade the uccx from 8.2 to 8.5 then application manager services are show in partical state.
Under UCCX service enginer.
application manager service are show ( PARTIAL_SERVICE).
I check the jtapi username and password are ok, I check the CTI route point and CTI port are registered.
Please can you help me on that how to resolved this issue.

Hi Ketanpatani,
Please run the JTAPI and Data Resyn operation from the UCCX Admin-> CUCM Telephony subsystem and look out for any inconsistencies between UCCX and CUCM.
Make sure all the CTI route points\ Triggers in enabled state.
If you have a UCCX HA setup, make sure to run all the services are in master state in UCCX Node1 (for this you can just reboot the UCCX second node so that all the services are running in master state from first Node of UCCX).
Thanks,
Anand
Pls rate helpful posts !!

Enterprise Manager can't show web-service in the web-services area

I'm deploying my application(stateless web-service) it work's well, but Enterprise Manager show that it's not a web-service, it can't show application in the web-services area, this fuсking server have many-many-many bugs and errors (fuсking developers was drunken a lot, imho), documentation's have many errors too, and I hate this server, but I need to use it on my work :-(
p.s. read documentation's carefully it have many errors.
p.p.s. From Russia with LOVE! Russian developers are the best from the best!

Hello,
Could you be more specific about the version of OracleAS you are using?
- which exact version ? (10.1.3.x, 10.1.2.x or 9.0/x)
- which kind of Web Service are you developing? (J2EE 1.4/JAX-RPC or earlier version)
Also if you find bug in the documentation or product please send let the Oracle Support Service knows.
Regards
Tugdual Grall

Are Group Managed Service Accounts supported by BizTalk?

Hi all,
I saw that there is already a discussion about the Managed Service Accounts support in BizTalk (http://social.msdn.microsoft.com/Forums/en-US/ffcea33b-652b-4866-8bb2-21ffc7d8bffa/are-managed-service-accounts-supported-in-biztalk?forum=biztalkgeneral) with
a clear response to NO.
But Windows 2012 R2 introduced the "Group Managed Service Accounts" which seems to be a better way to workaround the MSA limitations.
Are the gMSA supported in BizTalk?
Thanks.

While the documentation mentions that gMSA are managed by the Domain Controller and is introduced in Windows Server 2012. I interpret this to imply that this functionality would be AVAILABLE ONLY if you're running your DOMAIN CONTROLLERS on a Windows Server
2012 or higher DOMAIN.
If you just setup BizTalk on a Windows Server 2012 machine but in a domain which is running on Windows Server 2003 or 2008 compatibility mode because of other things such as Exchange, etc. then you WOULD NOT be able to leverage the gMSA functionality.
If on the other hand, your domain controllers are running Windows Server 2012 and Domain Level is Windows Server 2012 then you should be able to leverage gMSA accounts for BizTalk/SQL/IIS Service accounts.
Regards.
NOTE: The effect of a gMSA account on the Enterprise SSO service which has a serious dependency on the service account password and encryption however would still need to be evaluated.

SQL SERVICES ARE MISSING IN CONFIGURATION MANAGER

hi
We have recently migrated SQL2008 to SQL2012 enterprise edition on WINDOWS 2012,and everything is running fine.
Today i have just opened SQLCONFIGURATIONMANAGER for normal services checkup,but i couldn't find any SQL services in it expect integration services.i have checked in SERVICES.MSC and all services are running, this happened suddenly before it was alright(i
could see all the services)could some one please help me in finding the reason for sudden missing of the SQL services in CONFIGURATION MANAGER and way to get them back.
cheers

OK, so that is strange enough and looks like permissions issue with the WMI. There is an article for SQL 2008R2, which you can check and see if the solution helps you somehow - http://www.mssqltips.com/sqlservertip/2492/why-is-sql-server-configuration-manager-missing-services/
Ivan Donev MCT and MCSE Data Platform

Work Management Service: No tasks are shown on MySite

The work-management-service is not working.
On "MySite" the task-list is always empty (Pic.1), but there are tasks referenced to the profile.
I do not get errors in the ULS or on the task-page (refresh is OK).
Tasks are crawled and search works fine:
Are there any other settings i am not aware of ?

Increased the logging levels:
System.UnauthorizedAccessException: Access is denied. (Exception from HRESULT: 0x80070005 (E_ACCESSDENIED)), StackTrace:
at Microsoft.SharePoint.SPWeb.GetListFromWebPartPageUrl(String pageUrl)
at Microsoft.Office.Server.WorkManagement.ProviderOM.SharePointTaskAggregationUtilities.TaskCollector`3.<>c__DisplayClass56.<TryExecuteActionWithListLoaded>b__53(SPWeb web)
at Microsoft.Office.Server.WorkManagement.ProviderOM.SharePointTaskAggregationUtilities.TaskCollector`3.TryExecuteActionWithListLoaded(Func`1 fnGetCreateSite, Func`2 fnCreateWeb, Func`2 fnGetList, Func`1 fnGetListId, Action`3 toExecute)
at Microsoft.Office.Server.WorkManagement.ProviderOM.SharePointTaskAggregationUtilities.TaskCollector`3.TryExecuteActionWithListLoaded(Uri rootFolderUri, Action`3 toExecute)
at Microsoft.Office.Server.WorkManagement.ProviderOM.SharePointTaskAggregationUtilities.TaskCollector`3.FindNewTasksFromSearch()
at Microsoft.Office.Server.WorkManagement.ProviderOM.SharePointTaskAggregationUtilities.TaskCollector`3.CollectAndSyncTasks()
at Microsoft.Office.Server.WorkManagement.Internal.TaskAggregator.FarmRefreshJob.RefreshProvider(Nullable`1 lastSync, String providerKey, IWmaTaskProvider provider)
at Microsoft.Office.Server.WorkManagement.Internal.TaskAggregator.FarmRefreshJob.AggregateProviders()
at Microsoft.Office.Server.WorkManagement.Internal.TaskAggregator.FarmRefreshJob.ExecuteCore()
at Microsoft.Office.Server.WorkManagement.Internal.TaskAggregator.FarmRefreshJob.ExecuteAndDispose()
at Microsoft.Office.Server.WorkManagement.Internal.WmaContextUtils.<>c__DisplayClass1.<ExecuteCodeInsideWmaContext>b__0()
at Microsoft.Office.Server.WorkManagement.Internal.WmaContextUtils.ExecuteCodeInsideWmaContext(Action toRun, WmaContextType allowedContexts)
at Microsoft.Office.Server.WorkManagement.Internal.BaseContextRunner`2.ExecuteAndEnsureContextValid(Action toRun, TContextState serviceUserState, String actionName)
at Microsoft.Office.Server.WorkManagement.Internal.BaseContextRunner`2.ExecuteInSpContext(ThreadParams threadParams)
at Microsoft.Office.Server.WorkManagement.Internal.BaseContextRunner`2.ExecuteInDiagnosticScope(ThreadParams threadParams)
at Microsoft.Office.Server.WorkManagement.Internal.BaseContextRunner`2.Run(Object tParams)
at System.Threading.ExecutionContext.RunInternal(ExecutionContext executionContext, ContextCallback callback, Object state, Boolean preserveSyncCtx)
at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state, Boolean preserveSyncCtx)
at System.Threading.QueueUserWorkItemCallback.System.Threading.IThreadPoolWorkItem.ExecuteWorkItem()
at System.Threading.ThreadPoolWorkQueue.Dispatch()
SPRequest.MapUrlToListAndView: UserPrincipalName=, AppPrincipalName= ,bstrUrl=https://ksi-server.com/customer/issuetracking ,bstrUrlToMap=/customer/issuetracking/Lists/Tasks/MyOpenTasks.aspx
There is no "UserPrincipalName" set, therefore the "access denied"-error ?
Setup:
1 Webfrontend Server
1 Application Server
1 Database Server
Work "Work Management Service" is running on the Frontend-server, created with the "SharePoint Hosted Services" app-pool.

User Profile Application and Managed Metadata services are missing

Running SharePoint 2013 servers on a set of 2012 R2 Servers. One of our farm administrators deleted the Secure Store service account. They recreated the Secure Store account, but after doing so, the Managed Metadata Service and User Profile Service
are now unavailable.
When going to the User Profile Page, there is an error that says "Sorry, something went wrong."
When going to the Metadata page, there is an error that says "The Managed Metadata Service or Connection is currently not available."
There is an additional error that says "The Security Token Service is not available."
How can all three services be brought back online?

That specific event log error is as follows:
WebHost failed to process a request.
Sender Information: System.ServiceModel.ServiceHostingEnvironment+HostingManager/12547953
Exception: System.ServiceModel.ServiceActivationException: The service '/SecurityTokenServiceApplication/securitytoken.svc' cannot be activated due to an exception during compilation. The exception message is: Exception has been thrown by the target
of an invocation.. ---> System.Reflection.TargetInvocationException: Exception has been thrown by the target of an invocation. ---> System.ArgumentNullException: Value cannot be null.
Parameter name: certificate
   at System.IdentityModel.Tokens.X509SecurityToken..ctor(X509Certificate2 certificate, String id, Boolean clone, Boolean disposable)
   at System.IdentityModel.Tokens.X509SecurityToken..ctor(X509Certificate2 certificate)
   at Microsoft.SharePoint.Administration.Claims.SPSecurityTokenServiceManager.ConfigureTokenHandlerCollection(SPSecurityTokenServiceManager manager, SecurityTokenHandlerCollectionManager collectionManager, String key, SecurityTokenHandlerCollection&
tokenHandlerCollection)
   at Microsoft.SharePoint.IdentityModel.SPSecurityTokenServiceConfiguration.ConfigureTokenHandlerCollectionForLocalIssuer(SPSecurityTokenServiceManager manager, SecurityTokenHandlerCollectionManager collectionManager, String key)
   at Microsoft.SharePoint.IdentityModel.SPSecurityTokenServiceConfiguration..ctor()
   --- End of inner exception stack trace ---
   at System.RuntimeTypeHandle.CreateInstance(RuntimeType type, Boolean publicOnly, Boolean noCheck, Boolean& canBeCached, RuntimeMethodHandleInternal& ctor, Boolean& bNeedSecurityCheck)
   at System.RuntimeType.CreateInstanceSlow(Boolean publicOnly, Boolean skipCheckThis, Boolean fillCache, StackCrawlMark& stackMark)
   at System.RuntimeType.CreateInstanceDefaultCtor(Boolean publicOnly, Boolean skipCheckThis, Boolean fillCache, StackCrawlMark& stackMark)
   at System.Activator.CreateInstance(Type type, Boolean nonPublic)
   at System.RuntimeType.CreateInstanceImpl(BindingFlags bindingAttr, Binder binder, Object[] args, CultureInfo culture, Object[] activationAttributes, StackCrawlMark& stackMark)
   at System.Activator.CreateInstance(Type type, BindingFlags bindingAttr, Binder binder, Object[] args, CultureInfo culture, Object[] activationAttributes)
   at System.Activator.CreateInstance(Type type, BindingFlags bindingAttr, Binder binder, Object[] args, CultureInfo culture)
   at Microsoft.IdentityModel.Protocols.WSTrust.WSTrustServiceHostFactory.CreateSecurityTokenServiceConfiguration(String constructorString)
   at Microsoft.IdentityModel.Protocols.WSTrust.WSTrustServiceHostFactory.CreateServiceHost(String constructorString, Uri[] baseAddresses)
   at Microsoft.SharePoint.IdentityModel.SPSecurityTokenServiceHostFactory.CreateServiceHost(String constructorString, Uri[] baseAddresses)
   at System.ServiceModel.ServiceHostingEnvironment.HostingManager.CreateService(String normalizedVirtualPath, EventTraceActivity eventTraceActivity)
   at System.ServiceModel.ServiceHostingEnvironment.HostingManager.ActivateService(ServiceActivationInfo serviceActivationInfo, EventTraceActivity eventTraceActivity)
   at System.ServiceModel.ServiceHostingEnvironment.HostingManager.EnsureServiceAvailable(String normalizedVirtualPath, EventTraceActivity eventTraceActivity)
   --- End of inner exception stack trace ---
   at System.ServiceModel.ServiceHostingEnvironment.HostingManager.EnsureServiceAvailable(String normalizedVirtualPath, EventTraceActivity eventTraceActivity)
   at System.ServiceModel.ServiceHostingEnvironment.EnsureServiceAvailableFast(String relativeVirtualPath, EventTraceActivity eventTraceActivity)
Process Name: w3wp
Process ID: 5504

Content Distributor, deployment Manager and resource services are dead

Hi,
I am using Fast ESP 5.3 product single node in a window environment. Recently during a SAM patch installation I have restarted ESP and post that I have found below three services status as N/A in System Overview. Even the server was restarted
due to window patching. As these services are down I am unable to create any collection neither am I able to publish any search profile.
Content Distributor
deployment Manager
and resource services
Strangely in nctrl status all services are displayed as Running.
These are the work around I have tried:
killed processes from Task manager
Restarted ESP
So is there any possible way to bring these services up.
With Regards,
Santanu Mishra

With reboot of the server the issue got resolved....
Santanu Mishra

Cisco Provisioning Manager 2.1 bulk service area detailed configuring

Hi folks,
I'm really stuck and need some help desperately.
I have bought Cisco Provisioning Manager 2.1 for 5000 handsets and I have isntalled the product ok however I am now at the stage where I need to configure the service areas. I have some 45 sites which equates to about 350 service areas.
Service Area for each site with the following differences:
- Odd Device, Present CLI
- Even Device, Present CLI
- Odd Device, Restrict CLI
- Even Device, Restrict CLI
Can someone please advise me a way to bulk configure these detailed attributes with some tool or a let me know of a customer northbound API application that has been written to do make this painful exercise much less painful?
I estimate its going to take me 5 weeks full time to click through each thing and configure it..
Please help!
Cheers
Beau

You can bulk load (with batch provisioning) the Service Areas... I did this by exporting my phones into a CSV file from Communications Manager, and then filtered it for the fields required for the SAs. Then you just follow the instructions for batch provisioning that start here: http://www.cisco.com/en/US/customer/docs/net_mgmt/cisco_unified_provisioning_manager/2.1/user/guide/infrstct.html#wp1051558
I hope that helps...
--Joe

Are Managed Service Accounts Supported in BizTalk?

Hello,
Does BizTalk Server support the use of Managed Service Accounts for running host instances? Please see: http://technet.microsoft.com/en-us/library/dd560633(v=ws.10).aspx
Thank You,
PBR

I would not say complete No. Its yes and no.
Yes- You can use MSA on a single server quick (quick in terms of building an environment for test/dev) test BizTalk environment/dev. Is it a good practice to use MSA ? then its no.
Strict No: For multi-computer environment or in cluster, obviously you can't use MSA. Its also one of the limitations of MSA that it can't span multiple computers.
but there is no official word from BizTalk (at least I can't find one) to say not to use it in BizTalk. Its not advisable to use MSA in BizTalk, but you can in single-server dev./test environment technically.
If this answers your question please mark it accordingly. If this post is helpful, please vote as helpful by clicking the upward arrow mark next to my reply.

The Web Management Service service terminated with service-specific error %%-2147483640,

We've been able to successfully, automatically, deploy our MVC and WebApi to IIS7.5 on Win2008 R2, for some time now. Just this week the MSDeploy stopped working. The System event log shows this error when attempting to restart the Web Management
Service on the targeted Win200 R2 server:
The Web Management Service service terminated with service-specific error %%-2147483640.
The Application log shows this error at the same exact time the above error occurs.
IISWMSVC_STARTUP_UNABLE_TO_ACTIVATE_HWC
Failed to activate the Hostable Web Core (HWC). Web Management Service startup failed. Please reference the Win32 error in this event for further information. Exception:System.Runtime.InteropServices.COMException (0x8007007F): The
specified procedure could not be found. (Exception from HRESULT: 0x8007007F) at System.Runtime.InteropServices.Marshal.ThrowExceptionForHRInternal(Int32 errorCode, IntPtr errorInfo) at Microsoft.Web.Management.Server.WebServer.Microsoft.Web.Management.Server.Interop.IWebServer.Start()
Process:WMSvc User=NT AUTHORITY\LOCAL SERVICE
The above error is preceded by this warning:
A listener channel for protocol 'http' in worker process '7164' serving application pool 'WMSvcAppPool' reported a listener channel failure. The data field contains the error number.
Which is preceded by this error:
Failed to find the RegisterModule entrypoint in the module DLL C:\Windows\Microsoft.NET\Framework64\v4.0.30319\webengine.dll. The data is the error.
We've attempted to reach the target server using https://ourservername:8172/MsDeploy.axd. The response is:
Error 102 (net::ERR_CONNECTION_REFUSED): The server refused the connection
Is this occurring because the port is blocked or because the Web Management Service is not running? (The Windows Firewall with Advanced Security dialog says the "Windows Firewall is off" and there are no entries in the firewall log (C:\Windows\System32\LogFiles\Firewall).
We've seen some posts that indicate the certificate may be the issue. Not sure how to actually tell if this is the case though. The CERT we have says it is valid thru 2029.

Hi Nicola,
seems like your web service runtime is not configured correctly. Please check out the following SAP Notes:
Note 1043195 - Configuration of the Web service runtime
Note 1292171 - Troubleshooting Guide: ABAP Web Services Runtime
Kind regards
Heiko

R12 on Windows XP - Concurrent Manager Service

I installed R12 on WIndows XP.
It is working fine, but concurrent Manager Service is not getting created.
I tried with Auto Config...and also running directly ccmsvc.exe...
It always errors out displaying a window which reads Oracle Applications Concurrent Manager service encountered an error and needs to close. We are sorry for inconvenience.+
I looked at the Application log in Event viewer. It says Application: ccmsvc.exe and faulting module ntdll.dll.
Does any body know how to fix the faulting module ntdll.dll error....?
THanks in Advance
Ambati

Sorry for the delay...I was sick all these days....
I did restart the machine.....
THis is the error report in event viewer...and the version of ntdll.dll appears to be 5.1.2600.5512
Faulting application ccmsvc.exe, version 0.0.0.0, faulting module ntdll.dll, version 5.1.2600.5512, fault address 0x000249ab.+
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.+
I have Windows XP Service Pack 3 installed on my machine.

How to configure request manager service for multiple website in one web application

I have set up sp 2013 as below:
web application : wa1
site collection : sc1
sp site: site1, site2
I used 2 WFE, 1 APP, how can I use request manager service to control site1 to wfe1, site2 to wfe2?
Awen

That's not what i'd describe as load balancing.
A better description would be load-isolation. In your description then if the load on site1 was large (and growing) but site2 was quiet then site1 would struggle and eventually become unable to handle the number of users but site2 would still be ok. That's
fine from a QOS point of view but it's not the norm for load balancing. It would work in simple scenarios but the out of the box load balancing tools are much better suited than that sort of approach.
This article shows how to configure the RMS and may help show how your request is difficult to configure:
http://www.harbar.net/articles/sp2013rm2.aspx

How do you resolve Financial Management service validation error in EPM ?

Does anyone know how to resolve Financial Management service validation error from EPM Diagnostic Report?
Environment:
Quad-Core AMD Processor 2.2 GHz (Server Machine)
5 GB RAM
Server 2003 Standard 32-Bit SP2 (also tried in Enterprise)
Application Server:
WebLogic Server 9.2 Custom Installation (with Add-Ins)
http://www.oracle.com/technology/software/products/ias/htdocs/wls_main.html
Database:
Oracle 10gR2 (Standard Installation per step-by-step guide from Oracle)
http://www.oracle.com/technology/software/products/database/index.html
Hyperion EMP System 11.1.1.3:
Installer
Foundation Services (4 Files )
EMP Architect
Financial Management, Planning, Financial Reporting and Web Analysis (primarily interested in FM)
http://www.oracle.com/technology/software/products/bi/performance-management/index.html
The following are the sequences of steps carried out during the Installation and Configuration of EPM:
1)     Installed the Server along with its respective SP2 – Shutdown the machine
2)     Assigned IP and DNS addresses
3)     Installed Window components by ticking Application Server Console, Enable COM+ access, IIS and DNS
4)     Run “dcpromo” to create a Domain Controller with default values and assigned a domain name – Shutdown the machine
5)     Installed Weblogic Server 9.2 and configure it using Configuration Wizard – Selected “test environment” and ticked default “listening port” – Shutdown the machine
6)     Basic installation of Oracle Database 10gR2 using Step-by-Step guide provided by Oracle and carried out Password Management steps. After installation, I then created a user “oracle” and assigned it to ora_dba User Group with the required Local Security Policies – “log on as a batch job” and “Act as part of operating system”
7)     Logged into database and acknowledge the licensing window – Shutdown the machine
8)     Restarted the machine and checked all relevant and newly installed Database and WebLogic services are running.
9)     Started Installing EPM components by double clicking “InstallTool.cmd” and selected all relevant components at ONCE as per Installation Guide – Result: - All selected EPM components were successfully installed without errors or exceptions
10)     At the end of installation window, I carried out the configuration in the following scearios:
Scenario 1: Configuration all at Default settings
Scenario 2: Configuration all, except “Application Server” I selected the WebLogic9.2
Scenario 3: Configuration all, except “Application Server” and “Workspace Web Server” were being Welogic9.2 and IIS HTTP
RESULT: After all numerous installations, all came down to ONE ERROR from “Diagnostic Report” stating the following:
Financial Management:
FAILED SVR: HFM Service Validation Check if HFM service in working state.
Error: Error message: <03/11/2010 05:32:26 PM> CreateApplicationCAS... Failed at line: 2
Recommended Action: Make sure HAT utility is working. 1 s
I then simply ignored this error and tried to deploy an Application, all worked fine until you get to the point at “Job Console” where you need to press “Refresh” button. Progress remained at 12% until it got timedout after 300 seconds and force attempt of refreshing resulting in “aborted” job with the following error:
Error Reference Number: {DB3940F5-2D4A-46AB-A370-77F82F121BBA}
Num: 0x8000ffff;Type: 0;DTime: 4/12/2010 4:39:58 PM;Svr: PBAR;File: CHsvDataSourceImpl.cpp;Line: 196;Ver: 11.1.1.3.0.2413;
Num: 0x8000ffff;Type: 0;DTime: 4/12/2010 4:40:07 PM;Svr: PBAR;File: CHsxServer.cpp;Line: 1276;Ver: 11.1.1.3.0.2413;
Num: 0x8000ffff;Type: 0;DTime: 4/12/2010 4:40:07 PM;Svr: PBAR;File: CHsxServer.cpp;Line: 1190;Ver: 11.1.1.3.0.2413;
Num: 0x8000ffff;Type: 0;DTime: 4/12/2010 4:40:07 PM;Svr: PBAR;File: AgentHelper.cpp;Line: 728;Ver: 11.1.1.3.0.2413;
Num: 0x8000ffff;Type: 1;DTime: 4/12/2010 4:40:08 PM;Svr: PBAR;File: CHfmAwbAgent.cpp;Line: 744;Ver: 11.1.1.3.0.2413;
This is, I believe preventing me from deploying Consolidation Apps, including Sample Application provided with EPM Downloads. I have tried installing and configuring by components. All failed with the same outcome.
I have been working on this effortlessly in different combinations to get at least one Financial Management Application get deployed so I could enhance my learning adventure. As it stands, I am not sure where to get help and completely lost in the World of Oracle. I am also come to wonder whether “Free Downloads of EPM” are indeed, is “complete and is in working-state” or do I need a licence to use for personal learning experience? Are there different downloads for different needs or/users For example, eDelivery downloads are different from OTN Agreement downloads?
I have downloaded the files from following URL:
http://www.oracle.com/technology/software/products/bi/performance-management/index.html
I am completely lost and all services are up and running and not sure what I am missing!! Any assistance will be greatly appreciated.
Many Thanks
BT
Edited by: user8973921 on 13-Apr-2010 05:08
Edited by: user8973921 on 13-Apr-2010 10:56
Edited by: user8973921 on 14-Apr-2010 02:30

I am having exactly the same problem using Windows 2003 Standard editions SP2. Is there anyone who knows a possible solution for this? The effect on HFM is that is not possible to create an application, since I always get an error that says "Server execution failed"
Error Reference Number: {E68F87E6-588E-4665-862C-AAB02CB299DA}
Num: 0x80080005;Type: 0;DTime: 12/3/2009 5:21:47 PM;Svr: KINGTUT;File: CHsxServerImpl.cpp;Line: 3522;Ver: 11.1.1.3.0.2413;
Num: 0x80080005;Type: 0;DTime: 12/3/2009 5:21:47 PM;Svr: KINGTUT;File: CHsxServer.cpp;Line: 1115;Ver: 11.1.1.3.0.2413;
Num: 0x80080005;Type: 0;DTime: 12/3/2009 5:21:47 PM;Svr: KINGTUT;File: CHsxServer.cpp;Line: 857;Ver: 11.1.1.3.0.2413;
Num: 0x80080005;Type: 0;DTime: 12/3/2009 5:21:47 PM;Svr: KINGTUT;File: CHsxClient.cpp;Line: 2106;Ver: 11.1.1.3.0.2413;

CSCul38768 - Management services are unresponsive fault seen

Similar Messages

Maybe you are looking for