DOM support on a c6k platform
Hi,
I was wondering that I'm not able to get transceiver details on a c6500 (with sup720-bxl) platform running version 15.1(1)SY1.
Xenpaks will do fine:
c6504#sh int Te3/3 transceiver
ITU Channel not available (Wavelength not available),Transceiver is internally calibrated.Alarms applicable when thresholds or values are not N/A.If device is externally calibrated, only calibrated values are printed.++ : high alarm, + : high warning, - : low warning, -- : low alarm.NA or N/A: not applicable, Tx: transmit, Rx: receive.mA: milliamperes, dBm: decibels (milliwatts). Optical Optical Temperature Voltage Current Tx Power Rx PowerPort (Celsius) (Volts) (mA) (dBm) (dBm)---------- ----------- ------- -------- -------- --------Te3/3 30.1 N/A 30.4 -- -0.9 -2.0
While a SFP-GE-L fails:
c6504#sh int Gi4/23 transceiver
Diagnostic Monitoring is not implemented.
The SFP has definitivly DOM/DDM support enabled. If I plugg the optic in a C2960G switch, I can query the transceiver details-
c6504#sh int transceiver supported-modulesMod DOM support---- -------------- 1 Applicable 3 Applicable 4 Applicablec6504#sh int transceiver supported-list Transceiver Types depends on Supervisor/Line card Transceiver Type Cisco p/n min version supporting DOM ------------------ ------------------------- DWDM GBIC ALL DWDM SFP ALL RX only WDM GBIC ALL DWDM XENPAK ALL DWDM X2 ALL DWDM XFP ALL CWDM GBIC NONE CWDM X2 ALL CWDM XFP ALL XENPAK ZR ALL X2 ZR ALL XFP ZR ALL RX only WDM XENPAK ALL XENPAK ER 10-1888-04 X2 ER ALL XFP ER ALL XENPAK LR 10-1838-04 X2 LR ALL XFP LR ALL XENPAK LW ALL X2 LW ALL XFP LW NONE XENPAK SR NONE X2 SR ALL XFP SR ALL XENPAK LX4 NONE X2 LX4 NONE XFP LX4 NONE SX GBIC NONE LX GBIC NONE ZX GBIC NONE CWDM SFP ALL RX only WDM SFP NONE 1000BaseSX SFP ALL 1000BaseLX SFP ALL 1000BaseZX SFP ALL 100BaseSX SFP NONE 100BaseLX SFP NONE 100BaseZX SFP NONE GigE BX U SFP ALL GigE BX D SFP ALL SFP+ SR ALL SFP+ LR ALL SFP+ LRM ALL SFP+ ER ALL X2 LRM ALL CFP SR4 ALL CFP LR4 ALL
Any hints?
Thanks,
Thomas
Most linecards on the 6500 do not support DOM even though the transceivers are capable.
Please refer to the matrix in the following document, beginning on page 47:
http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6981.pdf
Please rate helpful posts.
Similar Messages
-
Disable DOM Support on Cat3750x and 2960S
ist it possibile do disable DOM monitoring or disable log warnings (other than doing log filtering ...) ?
on this link:
https://supportforums.cisco.com/document/75181/digital-optical-monitoring-dom
Following commands are mentioned:
Router(config)#transceiver type all
Router(config-xcvr-type)#monitoring
Router(config-xcvr-type)#end
BUT theses commands do not exist on C3750X ....
Any other idea ?It appears the feature is not supported on all hardware platforms, even though they may support DOM-enabled transceivers. The IOS feature navigator doesn't get down to that level of detail.
I was able to find reference to its being supported on Catalyst 6500, Catalyst 7600 and ASR 901.
It appears in the 4500 Configuration Guide but not in the associated command reference, so it appears it's not actually supported there. I found no reference at all in the 3750-X or 2960-S configuration guides.
I checked it on a 6500 - it works there. Checking on a 4500-X and 3750-X - it doesn't work on those. (All are running pretty recent IOS levels.) -
Is JavaMail 1.3.3 supported on z/Linux platform
Hi, I would like to know are following libraries supported on z/Linux platform ?
1) JavaMail 1.3.3 and
2) Java Activation Framework 1.0.2
Or can you please send me the known issues, if any ?
Also would appreciate if could send me any info/link for 64 bit JVM support for these.
Thanks a lot in advance / Rajan KumarJava is supposed to be Write Once Run Anywhere. So I would assume that ordinary Java code would run on z/Linux, 64-bit or otherwise, until my tests proved otherwise.
-
Oracle 9i Data Guard supported on Windows 2000 platform ?
Is Oracle 9i Data Guard supported on Windows 2000 platform ?
YES, we are currently using Data guard on 2000 Windows Server. Will need to have the Management server installed in order to get the Data guard function.
-
Will CS6 still be supported on Windows XP platforms?
Will CS6 still be supported on Windows XP platforms now that Microsoft no longer support this operating system?
Hi Zardos999,
Welcome to Adobe Forums.
Some applications will work on windows xp and some applications will not work. ( For eg. Premiere Pro, Encore, After effects will not work).
Which Adobe Application are you using?
Please check out the system requirements in the below link.
http://helpx.adobe.com/x-productkb/policy-pricing/cs6-system-requirements.html
Thanks -
When will IPV6 be supported on Sup2u/MSFC2 platform in software?
When will IPV6 be supported on Sup2u/MSFC2 platform in software? If it's avalible now, where do I find it?
Check the below links. Cisco supports IPV6 in almost all the router platform starting 12.2(2)T.
http://www.cisco.com/warp/public/732/Tech/ipv6/
http://www.cisco.com/en/US/partner/products/sw/iosswrel/ios_abcs_ios_the_abcs_ip_version_60900aecd800c1132.html -
WSRP Support Kit for WebLogic Platform 8.1 SP2
The WSRP Support Kit for WebLogic Platform SP2 has just been released at
http://dev2dev.bea.com/products/wlportal81/articles/wsrp_support_kit.jsp.
Please note that this is a preview release, and requires WebLogic
Platform 8.1 SP2.
Regards,
SubbuThere is a release planned for mid Summer, but it is too early to confirm.
In case you must add WSRP support to apps in platform domain, you can do
so manually, and here are the steps.
- Create a platform domain before installing WSRP Support Kit.
- Create a portal domain after installing WSRP Support Kit.
- Replace <Security> element in config.xml in the platform domain with
the one from portal domain.
- Add wsrp-common.jar file to the system classpath for the platform domain.
Let me know if this helps.
Subbu
Murtaza Sonaseth said the following on 01/07/2004 02:51 PM:
Is there an planned final release date for WSRP or at least a rough timeframe?
Thanks,
M Sonaseth. -
Ask the Experts Session on AJAX Support in the Java Platform -- June 19-23
Got a question about AJAX support in the Java Platform? Post it on the Ask the Experts page (http://java.sun.com/developer/community/askxprt/) during the week of June 19 and get answers from Sun experts Greg Murray, Mark Basler, and Carla Mott.
Perhaps this explains why Sun removed the crossposting ban from the site "Terms of Use"?
-
Ask the Experts Session on AJX Support in the Java Platform -- June 19-23
Got a question about AJAX support in the Java Platform? Post it on the Ask the Experts page (http://java.sun.com/developer/community/askxprt/) during the week of June 19 and get answers from Sun experts Greg Murray, Mark Basler, and Carla Mott.
Perhaps this explains why Sun removed the crossposting ban from the site "Terms of Use"?
-
after formating when tryed to install software to the target this Error Shown
NI PXi 8108
The Selcted Target does not support this function
when I try to add PXi chassis this Error Shown
PXI Platform Services version on the target appears to be older then 2.0.0 this host only supports targets running PXI Platform Servies 2.0.0 and later Upgarade your target in order to configure its PXI properties from this Host
Help me!Hi Lukas,
I think the problem is caused by differenet drivers for the CAN communication.
NI provides two driver for CAN: NI-CAN and NI-XNET.
NI-CAN is the outdated driver which is not longer used by new hardware. NI replaced the NI-CAN driver with NI-XNET some years ago, which supports CAN, LIN and the FLEXRAY communication protocol.
You wrote:
In order to fix this problem I have formatted my PXI and I have installed the following SW from the iPC:
3. NI_CAN 2.7.3
NI CAN is the outdated driver. I think that you should try to install NI-XNET instead of NI-CAN on your PXI-System, to get rid of the error message.
Regards, stephan -
What determines whether 3D is supported on a given platform?
I'm using the 2.0 beta (build 34) on Windows 7... when I call Platform.isSupported( ConditionalFeature.SCENE3D ), I get a result of 'false'.
What determines whether or not 3D is supported on a given platform?I just found the resolution to my problem in Jira, at: http://javafx-jira.kenai.com/browse/RT-14415
Specifically, this comment:
The minimum driver version for Intel HD was recently changed to 8.15.10.2302 to workaround bugs in older drivers.
If you run JavaFX as follows, it will show you your driver version number, and also print the minimum version number.
1. Set the environment variable NWT_TRACE_LEVEL=4
2. Run any JavaFX program with: java -Dprism.verbose=true ... -
Is DOM supported using SNMP on Cisco 6500;s?
Is DOM supported using SNMP on Cisco 6500's? I've configured DOM on 6509 using transceiver type all -> monitoring. Is DOM enable for SNMP mibs? Here's the MIB I got from a vendor. .1.3.6.1.4.1.3607. And I'm unable to walk it on any of my Cisco devices including Nexus 5672 and 4900.
That oid looks like the sysoid for the ONS series of products. I don't think that will work in this case. Unfortunately, I can't offer any other advice, I've not looked into snmp support for DOM.
chris -
DOM support for 40G transponders on the Nexus 3172PQ switch
I have a new Nexus 3172PQ system which supports 40G transponders, but when the "sh inter ether 1/49 trans det" command is executed, the system responds with DOM is not enabled. I have transponders that support DOM in the system (QSFP-40G-LR4). IOS is 6.0.2. Question is does the 3172 support DOM for the 40G transponders?
FEX dual home is planned for mid next year.
MP BGP VPN V4 not supported on the platform. Not sure about the roadmap item either. -
URGENT: Browser support w/BEA Portal (Platform 7)
Hey,
I just "noticed" that officially, the supported IE browser for BEA Platform 7
is v.5 or above.
My question is, what specifically is not supported with an older IE browser -
v4.0.1 actually. As it is, I would have to deploy to a corporate platform that
is currently using IE 4.0.1. That cannot change in the near future - so if IE
4.0.1 will NOT work with BEA Portal, I have a problem.
Thanks...
Nick Miron
CGI Services to BCEHey,
I just "noticed" that officially, the supported IE browser for BEA Platform 7
is v.5 or above.
My question is, what specifically is not supported with an older IE browser -
v4.0.1 actually. As it is, I would have to deploy to a corporate platform that
is currently using IE 4.0.1. That cannot change in the near future - so if IE
4.0.1 will NOT work with BEA Portal, I have a problem.
Thanks...
Nick Miron
CGI Services to BCE -
Supported JDK Versions and Platforms
Any further information on backward compatible JDK versions and what underlying Platforms are supporting.
We are on PA-RISC and Solaris.
We are coming off jProfile and intend to test this kit, please excure very basic question and many thanks in advance.
Many thanks for your help!
CheersThe usage of Flight Recording is only for JDK 7 update 4 and later versions of the JVM.
Using the Java Mission Control Client
The Java Mission Control interface use JMXRMI (JVMX over RMI) with J2SE 5.0 and later versions of the JVM.
Managing JVM Connections
Regards!
Maybe you are looking for
-
Problems connecting Macbook to Infocus X2 Projector
I'm trying to set up my Macbook to project through my Infocus X2 projector using an Infocus Liteshow wireless card. I can get the screen to project but the visual comes up looking kind of like a 'negative' image. I've fiddled with my display settings
-
Item category not defined in batch split in vl02n
HI GUrus, cna anybody please helpe me with this. We have to send 3 differnt batches of parts to the vendor via returns PO. when i go to vl02n and click on batch split to send out batch A - 5 EA, Batch B - 5 ea and Batch C - 5 ea. the system is throwi
-
File Sender Adapter - Multiple Source Directory
Hi all, I have the following file to IDoc Scenaraio: The source file might be in any of 3 directories in source system and so created file sender adapter as follows: File access parameters: Source Directory : Directory1 File Name : Filename*.
-
there are so many bad stuff like crashing and the maps and some other things.
-
Hi, Is it possible that when a user higlights a row in ALV, the entire row will be uneditable? Please teach me how. Thanks, Jim