Don't display caller number

I configure AutoAttendant through call router and call handler in unity ,but the caller number can't display and it prompts "From Voicemail" on phone before the call is picked up.And after picking up it,the caller number is display normally . Why ?

Hi,
Assuming that you've set up the call transfer to be 'supervised transfer' this is the behavior you're going to see. When Unity puts the original caller on hold in order to call your phone, the two call legs aren't bridged together, so the call appears to CallManager to be a simple call from Unity. When you pick up the call, then Unity bridges the two legs together, and CallManager changes the caller ID to reflect the change. If you reconfigure Unity to use 'release to switch' then you will see half a second of the call being from Unity, but when it bridges the two legs together (while your phone is still ringing), CallManager will immediately change the readout.
When you choose 'release to switch', Unity will put the caller on hold, dial the user's number, and connect the two. So, the caller should hear a very brief moment of music on hold, then hear the ringback from the phone, etc. To get it so that there's MoH until the recipient answers, you'd have to go back to 'supervised transfer', which would break your Caller ID.
HTH
//G

Similar Messages

  • E51 : How to Display Calling Number

    Help :
    How to Display the Calling Number along with Contact Number from the Address book when Receving Call from the number stored in the address book.
    Eg :
    Last Name : Z
    First Name : A
    Mobile : +1 12 123465789
    Tel(Home) : +1 12 987654321
    Tel(Office) : +1 12 192837645
    Now say this above said Contact Stored in my address book
    is calling on my cell phone.
    It shows only
    ZA
    Calling
    how to get the Number on display from which number the call is actually when it is ringing.
    either the Call is from Mobile or Home or Office.
    This feature is there in S60 v2 phones eg Nokia3230
    Help please

    As vmoisa said, this is a well known and a HIGHLY irritating bug. Here is a workaround - /discussions/board/message?board.id=communicators&​thread.id=15956
    Ofcourse, the correct solution would be a firmware upgrade.. I have seen this "mobile phone icon for all numbers" problem baffle new users (including me). It's a pity, because such a basic feature is implemented properly even on S40 phones!

  • Displaying called number on destination phone

    Hello,
    We are using UCM + CCX 7.   We are looking for a way to have the called number (or the digits passed for the called number) displayed on the recipient's IP phone -- for select extensions/agents -- versus showing the caller ID of the originator.    For an individual phone, I've tried checking "Dialed Number" under Forwarded Call Information Display, but it still shows the caller ID instead.   Does anyone know of a way to accomplish this, either through UCM or CCX?
    Thanks

    then you can have a look under call routing at Transformation Patterns => Called Transformation Pattern, create a CSS and PT for that apply it to the DevicePool of the Jabber phones.
    http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/9_0_1/ccmcfg/CUCM_BK_CDF59AFB_00_admin-guide_chapter_0110000.html
    http://www.cisco.com/en/US/docs/voice_ip_comm/cucmbe/admin/7_0_1/ccmcfg/b03cldpt.pdf

  • Nokia E7 don't display caller ID

    Hi!
    My phone only display numbers when someone is calling me.
    Even contacts I have stored in the phone book.
    Is this a bug or a setting somwhere?
    Firmware: PR 1.0 - 013.016
    N8 FW: 022.014 -- Please separate Artist & Albums!
    N86 8MP FW: 30.009 -- We need a new FW on this phone!
    E51 FW: 410.34.001
    E70 FW: 2.0618.07.10 -- Why no v3 for my code?

    Have a look at the link below and see if any of the suggestions help.
    /t5/Pool-of-Knowledge/Missing-Caller-ID-on-Calls-SMS/td-p/371913

  • No Caller Number Display since August 2014

    Caller number display ceased to function on 9th August last year.
    Since the we have been through the fault reporting process 3 times. Had an aborted (by Openreach) engineer visit and received a statement letter from BT saying they are looking in to the problem, it will take time etc etc.
    My equipment works at my neighbours house. The neighbours phone has been tried in my house and does not work. I have removed filters, unplugged everything, tried the Master Socket. None of these things works.
    It is very tough to run my business without Caller Number Display.
    Can it be fixed???
    If I switch to another provider will Caller Number Display then work??
    Help!

    Hi Unclenorm,
    Welcome to the community forum. I am sorry to hear that you are having problems with the Caller Display. I'll be able to take a look at this for you. Please can you send me in your details using the "Contact The Mods" link found in my profile.
    Thanks
    PaddyB
    BTCare Community Mod
    If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
    We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

  • Using a landline number as displayed caller id

    Is it possible to use a landline number as displayed caller id, instead of a mobile number?

    Hi, cb10,  and welcome to the Community,
    Unfortunately, no.  Skype does not have a means to verify a land line number.
    Regards,
    Elaine
    Was your question answered? Please click on the Accept as a Solution link so everyone can quickly find what works! Like a post or want to say, "Thank You" - ?? Click on the Kudos button!
    Trustworthy information: Brian Krebs: 3 Basic Rules for Online Safety and Consumer Reports: Guide to Internet Security Online Safety Tip: Change your passwords often!

  • TS1646 I am having a lot of trouble with trying to use my debit card to purchase on itunes it always tells me that my card number is invalid. But i know it isn't because i just got the account the only thing i havent done yet is called my bank to see if i

    I am having a lot of trouble with trying to use my debit card on purchase of itune apps or music. Whenever i put my card information in it tells me that this card is invalid. But there is no way that my card is invalid because i just got it last week. So the only thing i haven't done yet is call my bank to check and see if all my bank statements match but if they do then have no idea what to do to get this to work with my computer, ipad mini, or ipod    HELP! PLEASE!

    I am having this same problem and I have even contacted my bank. The address they have is EXACTLY the way I am typing it.  It does match.  I do not understand.

  • When I receive text messages, it displays phone number instead of contact name.

    I updated to iOS 5 on my iPhone 4 over the weekend. Since updating to iOS 5, all of my text messages show up with a phone number listed instead of the contacts name. I checked my contact info and all the contact information is listed and the numbers under the contact are correct. Has anyone else had this issue and if so have you discovered any resolutions?

    Following a tip from another poster, I was able to fix the issue (temporarily).
    This worked for me on Verizon.
    I dialed *228 on my Verizon phone. I pressed "1" to activate it over the air. I then went into task manager and killed all the running apps.. Waited a few minutes.
    The next text I got displayed the number correctly!.. Until I rebooted, that is.
    Ps. PLEASE, call Apple and speak with a senior engineer on this. They can't fix it if they don't know it's a problem! (800) MY-IPHONE

  • In setting where could i see the shipping cond. displayed as number first?

    Within a SO, currently the shipping conditions displayed as 'Normal Mode'...
    I remembered that if you setting somewhere, the shipping conditions could be displayed as <b>'01</b> Normal Mode'...
    As i could see the number..'01'.
    Do you know where to set this???
    Thanks!!!

    oh...i think you didnt get what i mean...
    But finally i got what i wanted...
    There is a button called 'Customizing Of Local Layout' on the top bar, click it->Go to 'Options'>Tab of 'Expert'->Controls..Check 'Show Keys in all Drop-down list'->Done
    Now restart the transaction 'VA03', you can see that the shipping cond. is displayed by number first..

  • Nokia 2310-not displaying caller name

    I've just bought a Nokia 2310 as they're very cheap as a standby phone but have a problem. I've copied the numbers from my simcard to the phone but if someone calls the phone, when it rings it only displays the number and not the name. This is obviously pointless as I would never know who's calling and makes missed calls a nightmare.
    What have I done wrong?

    The number in your phonebook has to match the one which is calling EXACTLY. So not 0489/235647 for instance, but you need to enter this number as +33489/235647 in your phonebook (the sign is important too). +33 is the country number of course.
    If you're still not sure, save the number from messages you have recieved and enter that in your phonebook. Doing this will ensure that the messenger's or caller's name is displayed.
    This is something I feel the manual should have adressed. You have no idea how much this **bleep** me off, until I found it a day later.
    k thx

  • Cinema display serial number from plist

    Hi, I need help getting my cinema display serial number from an old Plist file.  My office was broken into recently and someone made off with the monitor.  It's a long shot but I thought I could find the serial number for the campus police.  I was able to find an old com.apple.windowserver.plist file that had some information for the display.  I tried the command <defaults read ./com.apple.windowserver.plist> and came up with the following.  Problem is they don't look like serial numbers for a cinema display.  Any suggestions? 
                    DisplayID = 69530633;
                    DisplayProductID = 37430;
                    DisplaySerialNumber = 42039688;
                    DisplayVendorID = 1552;

    Hi ,
    Go to /Library/Preferences/com.apple.windowserver.plist. Open this with TextWrangler or a similar utility. Look for a DisplaySerialNumber key with an integer value that isn't 0. With any luck, this should be the s/n of your display.
    If you haven't used this display for a while, the records of it may be gone.
    Also, it appears that this isn't guaranteed. Double-check if possible.

  • Some graphs don't display in OEM Grid Control 10gR5 (10.2.0.5)

    A number of the performance graphs (e.g. Top Activity) don't display i.e. there is nothing but if if you right-click in the empty area you get a small pull down with Print, Settings, About Adobde Flash 10.
    This has all happend after upgrading to 10.2.0.5. OMS and client environment is:
    Windows 2003 SP2 (32 bit), IE 6 with Flash ActiveX 10, Flash Player 10.
    Anyone got any ideas or anyone got it working fine.
    Thanks.

    Windows Server 2008 OEM 11g Performance graphs do not display.
    Click OEM Performance Tab and IE7 information bar displays message:
    "Your security setting do not allow websites to use ActiveX controls installed on your computer. This page may not display correctly."
    Workaround: Disable Internet Explorer Enhanced Security Configuration in Windows Server 2008
    Unlike with previous versions of Windows Server in which you could disable Internet Explorer Enhanced Security Configuration by removing the component in Add/Remove Programs, Windows Components
    the Windows Server 2008 implementation of Internet Explorer Enhanced Security Configuration is configured through Server Manager.
    Select the root of the Service Manager navigation pane, and under the Server Summary click Configure IE ESC, which is part of the Security Information section.
    A dialog box appears, letting Internet Explorer Enhanced Security Configuration be enabled/disable separately for normal users and administrators.
    See YouTube video:
    http://www.youtube.com/watch?v=OO3PPN1olHY

  • SPA IP phones doesn't show calling number after the call was picked UP

    Hello,
       Our different CISCO SPA IP phones models (at this time we are using 7.4.8a version) are working with Broadsoft AS. And now we have a problem: when CISCO SPA IP PHONE pickups the call ( by pressing BLF lamp) and the call is connected, Cisco user doesn't see any information (calling name or calling number) with whom he is talking now. He on only sees on screen pickup extension *11 and info that the call is connected. From SIP traces I can see this information in PAI header in SIP 200 OK  message (when pickup was initiated).
      I also tried to change Caller ID Header - no luck. I've upgraded IP phone to latest version (7.5.1a)  - didn't help.
    I've experience with THOMSON and MGC. By pressing BLF , Thomson displays info who (calling number) is calling to your configured BLF line and gives you actions: retrieve this call or cancel - you can choose if you still want pickup this call.
    So can you give me some hints how to fix this issue? Our at this time CISCO IP PHONE doesn't have such feature?
    Thanks in advance,
    Giedrius

    Why not answer?
    bug is available from firmware 7-4-7 and above and are still
    on models SPA50x and SPA525

  • Display Extension Number Instead of Switchboard Number

    Hi,
    We are using CUCM system in one of our branch office, we want to display extension number instead of switchboard number when we call external. But the telecom company said the dial information we send is "Unknown", need to be changed to "National Effective"... The voice gateway is C2951 and it's configured by vendor before; I can't find any configuration related to that, or maybe there wasn't any. Can someone help with this? Thanks.

    Make sure the phones have external phone number mask and under route pattern you have Use Calling Party's External Phone Number Mask - checked. Then follow the below to set the called party number plan:
    If its a MGCP gateway then under the route pattern>called party transfomrations> set the called party number type to local/national/international depending for the respective route pattern.
    Review: http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/admin/8_5_1/ccmcfg/bccm-851-cm/b03cldpt.html#wp1350852
    If its H323/SIP you can use translation rules. Review the below document:
    http://www.cisco.com/c/en/us/support/docs/voice/call-routing-dial-plans/61083-voice-transla-rules.html#type_plan
    -Terry
    Please rate all helpful posts

  • New topics are compiled in but don't display when help button is pressed

    Folks,
    I'm using RoboHelp HTML Build 6. I am the only writer who uses RH and have been using this build for 2 years or so.
    I recently got a new map file from the developer containing 2 new map IDs. I used the same steps to import the map file, create the new topics, and map them to the new map IDs that I have been using for years. But when I compiled RH and pasted the chm into the application folder, those 2 new topics don't display when the help button is clicked on the dialog box to which they are mapped.
    When I generate the chm I can look at the output at the bottom of RH project view and see that that the 2 new htm files are being compiled into the RH project. I can also see them if I open the generated chm and go into the TOC and click on a link to them.
    Does anyone have any ideas? I have tried redoing the usual procedure (see below) for the importing and mapping from scratch several times. I have also tried BugHunter (see below).
    Procedure for Importing and Mapping (this time the help for all the older dialog boxes works but not for the 2 new ones)
    1. Open the new map (.hm) file from the developer and add #define followed by a space to each entry beginnng with the string HID in the new map file (I don't know why but nothing works unless I do this.)
    2. Delete the old map file from the RH project.
    3. In Windows Explorer, copy the new .hm file into the RH project folder.
    4.In Project Manager view, open Context-Sensitive Help. Right-click on Map Files. Select Import. Browse and select the new map file.
    6. Map the new topics using File, Edit Map IDs.
    7. Generate the .chm and pasted it into the application where it always goes.
    BugHunter Procedures and Results
    I first tried the Test HTML Help API dialog.
    I specified the .CHM file I compiled and tested both options:
    --HH_DISPLAY_TOPIC: I put in the name of the new help (htm) file and its relative path and clicked Help. Nothing happened.
    --HH_HELP_CONTEXT: I put in the Map Number for the new dialog box and clicked Help. The new help topic I had created displayed.
    I also used the Tools tab in BugHunter to do a CSH (context sensitive help) Test. I identified the chm file and opened it and put in a new map number, then clicked Show Help. Nothing happened.

    Welcome to the RH forums.
    On the surface it sounds like you have done everything correctly so it should just be a case of going back and double checking that you have the correct CHM, that the mapid is exactly the same as in the app and that the app has been updated.
    Read the RoboColum(n) for a tips, tricks and musings on the Technical Communication Suite products.
    Follow the RoboColum(n) on Twitter

Maybe you are looking for