Edit in Audition and the levels are different

Posted in Adition Forum as well
http://forums.adobe.com/thread/854150?tstart=0
Anyone able to check this please.
I have a test project in PremPro CS5.5 and I created a Bars and Tone Clip.
The Tone on the clip is -12db (VU meter)
I went "Edit in Audition" and the same audio wave reads -15db on the VU
Thoughts!

In Audition, go to Edit > Preferences > Multitrack and change Panning Mode to Left/Right Cut (logarithmic).
/Roger

Similar Messages

My screen splits in a half, and the colors are different

it happens to often , and obviosly y cant use it any more, unless y turn it of an on again. and some times, it happens when i turn it on. I only can see halh of the screen

Sounds to me as if the screen connection has come unseated. I would take it to your nearest Apple store or Apple Authorized Service Provider.

Why don't my photos appear as they do in iPhoto on my Apple Computer. Even though I specify to sync all Events, Faces, etc. the iPad 2 is missing Faces categories and the Events are in a different order.

Why don't my photos appear as they do in iPhoto on my Apple Computer. Even though I specify to sync all Events, Faces, etc. the iPad 2 is missing Faces categories and the Events are in a different order.

1) The best way to relocate the iTunes library folder is to move the entire iTunes folder with all subfolders to the new path, then press and hold down shift as start iTunes and keep holding until prompted to choose a library, then browse to the relocated folder and open the file iTunes Library.itl inside it.
If you've done something different then provide some more details about what is where and I should be able to help.
2) Purchases on the device should automatically transfer to a Purchased on <DeviceName> playlist, but it my depend a bit on whether automatic iCloud downloads are enabled. If there is a cloudy link then the transfer might not happen. You can use File > Devices > Transfer Purchases. In iTunes you should also check out iTunes Store > Quick Links > Purchased > Music > Not on this computer.
3) Backup the device, then immediately restore it. In some cases you need to add a restore as new device into that equation. Obbviously not to be attempted until you're sure all your media is in your library. See Recover your iTunes library from your iPod or iOS device should it be needed.
4) I believe there is complimentary 1 incident 90-day support with hardware purchases, but no free software support for iTunes itself. AppleCare gets you a different level of support.
tt2

The user and the mailbox are in different Active Directory Sites

Hi All,
I have 2 site, each site have an Exchange Server 2010 SP1, let say Site HQ and Site DRC I monitored it with SCOM 2007 R2, site HQ successfully monitored, then I continue try to monitor DRC site. I executed new-TestCasConnectivityUser.ps1 at MBX DRC Site
to create extest user.
Then I try to execute command to test-connectivity, but it failed.
Test-OwaConnectivity -TestType:Internal -MonitoringContext:$true -TrustAnySSLCertificate:$true -LightMode:$true | fl
RunspaceId : 6b709fa5-0719-4be5-ae62-ec4b3617a6e0
AuthenticationMethod :
MailboxServer : CONMBX02.contoso.com
LocalSite : CONMBX02.contoso.com
SecureAccess : False
VirtualDirectoryName :
Url :
UrlType : Unknown
Port : 0
ConnectionType : Plaintext
ClientAccessServerShortName : DRCCAS01
LocalSiteShortName : CONMBX02
ClientAccessServer : DRCCAS01.contoso.com
Scenario : Reset Credentials
ScenarioDescription : Reset automated credentials for the Client Access Probing Task user on Mailbox server CON
MBX02.contoso.com.
PerformanceCounterName :
Result : Failure
Error : [Microsoft.Exchange.Monitoring.CasHealthStorageErrorException]: An error occurred while t
rying to access mailbox CONMBX02.contoso.com, on behalf of user contoso.com\extes
t_xxxxxxxx
Additional information:
[Microsoft.Exchange.Data.Storage.WrongServerException]: The user and the mailbox are in
different Active Directory sites..
UserName : extest_xxxxxxxx
StartTime : 04/01/2012 20:46:19
LaCONcy : 00:00:00.0156460
EventType : Error
LaCONcyInMillisecondsString :
Identity :
IsValid : True
WARNING: No Client Access servers were tested.
RunspaceId : 6b709fa5-0719-4be5-ae62-ec4b3617a6e0
Events : {Source: MSExchange Monitoring OWAConnectivity Internal
Id: 1005
Type: Error
Message: Couldn't access one or more test mailboxes.
The service that is being tested will not run against these mailboxes.
Detailed information:
Local Site:DRCProduction
[Microsoft.Exchange.Monitoring.CasHealthStorageErrorException]: An error occurred while trying to
access mailbox CONMBX02.contoso.com, on behalf of user contoso.com\extest_xxxxxxxx
Additional information:
[Microsoft.Exchange.Data.Storage.WrongServerException]: The user and the mailbox are in differen
t Active Directory sites..
PerformanceCounters : {Object: MSExchange Monitoring OWAConnectivity Internal
Counter: Logon LaCONcy
Instance: DRCCAS01.contoso.com|DRCProduction
Value: -1000}
any help appreciate it.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.
Krisna Ismayanto | My blogs:
Krisna Ismayanto | Twitter: @ikrisna

Hi
   Removed existing test account on two site.
   Then created test account on DGC through new-TestCasConnectivityUser.ps1.
   Flushed Health Service on RMS.
Terence Yu
TechNet Community Support
Hi
What do you mean on DGC ? you mean I have remove both test account or just at DRC site only ?
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.
Krisna Ismayanto | My blogs:
Krisna Ismayanto | Twitter: @ikrisna

Test-OutlookConnectivity fails with '[Microsoft.Exchange.Data.Storage.WrongServerException]: The user and the mailbox are in different Active Directory sites'.

I have a two site DAG, and the command is running from the alternate site where the databases are not currently being hosted. The following command...
Test-OutlookConnectivity -Protocol:TCP -TrustAnySSLCert:$true -MonitoringContext:$true
...errors with the following output:
An error occurred while trying to access mailbox CurrentlyHostingMBServerName.InternalDomainName, on behalf of user InternalDomainName\extest_bb13200232474
Additional information:
[Microsoft.Exchange.Data.Storage.WrongServerException]: The user and the mailbox are in different Active Directory sit
es..
+ CategoryInfo : OperationStopped: (Microsoft.Excha...onnectivityTask:TestOutlookConnectivityTask) [Test-
OutlookConnectivity], CasHealthStorageErrorException
+ FullyQualifiedErrorId : F2F8AC0D,Microsoft.Exchange.Monitoring.TestOutlookConnectivityTask
I thought this command would work based on the 'AllowCrossSiteRpcClientAccess: True' option on the DAG. The command works well if run a CAS server in the active DB site.

Hi,
Exchange 2013 users use Outlook Anywhere to connect to CAS server. You may run the RCA to test the connectivity:
https://www.testexchangeconnectivity.com/
Thanks,
Simon Wu
TechNet Community Support

When I open my RAW files in Photoshop CC they are grainy and the JPEGS are not. What is going on? It doesn't seem to have anything to do with my CACHE levels either.

When I open my RAW files in Photoshop CC they are grainy and the JPEGS are not. What is going on? It doesn't seem to have anything to do with my CACHE levels either.

BOILERPLATE TEXT:
Note that this is boilerplate text.
If you give complete and detailed information about your setup and the issue at hand,
such as your platform (Mac or Win),
exact versions of your OS, of Photoshop (not just "CS6", but something like CS6v.13.0.6) and of Bridge,
your settings in Photoshop > Preference > Performance
the type of file you were working on,
machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
what troubleshooting steps you have taken so far,
what error message(s) you receive,
if having issues opening raw files also the exact camera make and model that generated them,
if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
A screen shot of your settings or of the image could be very helpful too,
etc.,
someone may be able to help you (not necessarily this poster, who is not a Windows user).
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!

What is the difference between the sports edition apple watch and the normal edition, is it the bands different or do the they have different apps. Also could you take the bands off and put new ones on(change the bands)?

what is the difference between the sports edition apple watch and the normal edition, is it the bands different or do the they have different apps. Also could you take the bands off and put new ones on(change the bands)?

what is the difference between the sports edition apple watch and the normal edition, is it the bands different or do the they have different apps. Also could you take the bands off and put new ones on(change the bands)?

I bought an iPhone in Australia and now I cannot use it in South Africa as the Vodacom network cannot assist me by getting internet on the phone as the settings are different. What should I do to get the phone working in South Africa?

I need to know how I can get my iPhone to work in South Africa. I used it in Australia and was told I could use it in SA...but now I am told the settings are different and therefor I cannot get the internet to work on my iphone. How can I get this working?

Try this
Vodafone (Vodacom) South Africa
APN: Internet
Username for APN: web
Password for APN: web

Error The PC and the printer are connected to different networks

Hi,
I'm trying to set up my C4580 on my laptop, but I'm getting the following error after the diagnostic test:
The PC and the printer are connected to different networks(237DB2A87D and 66616B65). They must be connected to the same network. This can happen when you use the manufacturer's default network name (SSID) and another nearby network is using the same name.
My setup is a Linksys router WRT546, my laptop is conntected wireless to the router. I have two other desktop computers that are directly connected to the router. Both the desktops are able to connect wireless to the printer. My router SSID name is 'Blair Office' with WPA security.
I get a internet connect fine with the laptop, but can't get the new printer to setup.
I saw another post that talked about 'Print the C45** Network Configuration Page', but not sure how to do this
Thanks
Diane

This reply may be late for this user, but it might be helpful for any current users.
I managed to change the modem's IP address to match that of the printer. In my case the printer worked fine wirelessly until I moved to a new place and installed a new modem. Here is what I did to solve the problem:
1. At the printer, click on the wireless button, wireless settings, print network configuration page. This will print a page with the printer's IP address (in my case: 192.168.0.13)
2. I accessed my modem via the internet browser, typing 192.168.1.1 (this is one of the default addresses (192.168.0.1 is also common). Default user and password is admin (usually). There I changed the modem's IP address to 192.168.0.1 and the range to start at 192.168.0.13 (my printer's IP address).
3. I saved the settings (the modem will reboot and you will be offline, it may take some 20 seconds before the modem is visible again).
4. Reconnect to the modem and check if internet is still working. Then try to install the printer again.
This worked for me after I read several other postings.
Good luck!

I will travel to France and let me know if I should buy any adapter to charge my iphone?, because the plugs are different than here in chile

I will travel to France and let me know if I should buy any adapter to charge my iphone?, because the plugs are different than here in chile

Hi Shawn,
It sounds like the person who installed the hardware didn't install the software properly for you. You should reinstall this to get full functionality and control yourself.
The process is easy:
) With the computer on, close all programs that are running and put the Creative CD-ROM into your computer's CD or DVD dri've. There are probably several disks; the one that you want should say 'Intallation and Applications CD' on the label.
2) The Setup program should start automatically in a few moments, but if nothing happens, click your Start menu and choose Run..., then click the Browse button. From the 'Look In' drop-down menu, choose your CD/DVD dri've. In the list of files that appears, choose the one called Setup or Setup.exe.
3) The Setup program will let you choose what to install. Choose to install everything. There might be two separate Setup processes that start after this: one for the soundcard's drivers, and one for the Creative MediaSource software. Within each process, when you are given the choice of Full, Custom, or Basic, select Full in each case. Follow the instructions in the programs and they will guide you through the setup process.
IMPORTANT: you will likely be given the option to use digital output only to your speakers. Only select this if you have digital speakers, attached to the sondcard through only one digital cable. If your speakers are attached using several cables, you should use analog output.
4) Once all of the Setup programs are completed, they will probably have you restart your computer.
All of the above should have been done when the card was first installed, but it seems that whoever you paid to do the installation didn't bother with the software install.
After this is all done, you should be able to use all of your speakers. If you are still having trouble, you will be able to follow the instructions that you were given before on how to enable CMSS.
Good luck!
Neeraj Mathur

When putting an event on my iPhone calendar and the time, when it goes to iCloud to my laptop or iPad calendar the times are different. How can I make the time the same?

When putting an event and the time on my iPhone calendar, when it goes to iCloud to my laptop or iPad calendar the times are different. How can I make the time the same?

Welcome to the Apple Community.
Is the calendar you are adding events to on the phone an iCloud calendar.

When i sync my ipad and imac on ical the times are different yet the time zones are the same, any ideas why?

when i sync my ipad and imac on ical the times are different yet the time zones are the same, any ideas why?

Under the summary tab in iTunes make sure you have Automatically Back Up This computer. If you have iCloud selected it won't back up when syncing.

Audio Levels Are Different within program

For some reason when I am editing a multi-track project I seem to get three different levels as I go along. When I am editing a single file the levels come out as one thing. When I get the levels good, usually around -4 or so I play them back on the multi-track editor and I'm well up and over 0 into the red. On top of that when I import back into the Final Cut all the levels are completely different wiht some being low and some behing higher than in Soundtrack Pro. All level adjustments made in Final Cut were cleared out so any project I bring in doesn't have any level variations.
Thanks!!

Also, in the sequence the Edit in Audition option is greyed out? I can't round trip and work through the clips individually? Is there something I need to switch on or something?

Issue after Migration: ID and Content-ID are different in SOAP Payload

Hi Experts,
I am facing a strange issue in the PI landscape after the migration from XI 3.0 to PI 7.1.
The scenario is from R/3 system to TIBCO System (Proxy-to-SOAP). The TIBCO system receives the file in SOAP Format. The message is sent from PI via SOAP adapter to TIBCO System.
There is a attachment coming from the R/3 System along with the main message and the main payload/message has a "attachment-ID" as a field. Earlier what used to happen in XI 3.0 that the "Attachment-ID" used to equal to the "Content-ID" when the SOAP payload was generated at the TIBCO end. Now after migration, in PI 7.1 the "Attachment-ID" and "Content-ID" are different. We have control over the "Attachment-ID" as it is coming from the source payload but we do not have any control over the "Content-ID" as we are not creating it.
Can anyone of you please let me know how the SOAP Payload is created and how the content-ID gets populated in the Header of the SOAP Envelope? Also, can anyone help me to fix this issue? Is it something which needs to be handled by us or the BASIS Team?
Thanks,
Arkesh
Edited by: Arkesh Sharma on Dec 16, 2011 12:53 PM

Hi Ramesh,
Thank You for the very Helpful Answer. Before I proceed and close this thread, I have one more question which comes to my mind:
I create my own SOAP Header if I apply the solution provided by you then will the rest of the details in the SOAP Header payload will change or do I need to customize it for myself? For e.g., there is a field named MessageId in the SOAP Header. If I write a Java Mapping, do I need to manually populate the MessageId field in the SOAP Header of my java code or will it be automatically populated?
My requirement is to change only the content ID of the SOAP Header Payload and the rest of the fields should remain the same as it is. Is it possible with the approach that you mentioned above?
Thanks,
Arkesh

Sdm and administrator password are different

Hi,
We have Portal 7.0 EHP1 system which is being used for Java development and has ESS, MSS business packages installed.
The administrator password expired, so I changed through the browser whenrein it gave option to change.
While the SDM password is same as before.
So, now the administrator and SDM passwords are different, earlier they were same.
Will this create any issue? If yes, how to resolve it?
Thanks & Regards,
Kunal.

Hi Kunal,
To set the admin password permanent:
Open Offline Config Tool -> Switch to Configuration Editor Mode. Navigate to cluster_data -> server -> cfg -> services PropertySheet com.sap.security.core.ume.service
Switch to edit mode
open the propertysheet.
It will prompt you for a security warning, accept and proceed further.
Look for value ume.logon.security_policy.password_expire_days. The default value will be 90 days. Change it to custom value 999999 and save it. Restart the engine and your Administrator user password will not get expired.
Thanks and Regards,
Shyam.

Edit in Audition and the levels are different

Similar Messages

Maybe you are looking for