FXS Port stucks in Off-Hook state on NM-HDA

Hi,
i have some trouble with an FXS Port on an NM-HDA which stucks in the Off-Hook state, after some time of normal operation. The Voice-Port is in Off-Hook state regardless of if there is an Enddevice attached or not. Even an reload of the router does not help.
The voice port is configured for loop-start. The NM-HDA is housed in an Cisco 3725 running IOS Vers. 12.3(14)T2 with H.323 signalling.
Is there anybody who has seen this before? Could this be caused by an IOS-Bug or is it more likley that the NM-HDA is faulty?
Regards
Robert

Here's the bug ID: CSCse15025
Doubt the NM is faulty - we had the same issue in a 2821 and migrated to 12.4(4)T4 to correct it. No hardware replacement required. All has worked fine since then.
HTH
Tom

Similar Messages

VG224 port stuck in 'off-hook' state

Hi All,
I have strange problem with my VG224 connected to CME4.0.
I have 1 port have no dial tone. And 'show voice port sum' result
VG1050005#sh voice port sum
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
============== == ============ ===== ==== ======== ======== ==
2/2 -- fxs-ls up dorm off-hook idle y
ADMIN is UP, OPER is DORM, but IN STATUS is OFF-HOOK
VPM STATE from 'sh voice call sum' is FXSLS_ONHOOK
I have already shutdown this port and reload the VG224 and unplug the analog phone. But no effect.
FYI, Im running IOS version 12.4(9)T1 for VG224.
Any solution for this problem?
Thanks.
Iwan

Configuration for VG
======================
stcapp ccm-group 1
stcapp
stcapp feature access-code
prefix *#
voice-card 0
interface FastEthernet0/0
ip address 10.102.1.35 255.255.255.0
duplex auto
speed auto
voice-port 2/2
cptone ID
timeouts call-disconnect 2
timing hookflash-in 500 150
sccp local FastEthernet0/0
sccp ccm 10.102.1.12 identifier 10 version 4.0
sccp
sccp ccm group 1
associate ccm 10 priority 1
dial-peer voice 3 pots
service stcapp
port 2/2
=========================
This port work well for 2 weeks before this problem happen. Another port have same configuration and its working

WRP400 hangs in off hook state

Hello,
we have a client which uses WRP400 for T.38 faxing. It has modem connected to FXS port. Usually every 2weeks WRP400 hangs in 'off hook' state for that FXS port and no reboot helps to fix that. Only after firmware rewrite line hook gets in place. We use 1.00.06 version of firmware. Any thoughts on a problem?

Here's the bug ID: CSCse15025
Doubt the NM is faulty - we had the same issue in a 2821 and migrated to 12.4(4)T4 to correct it. No hardware replacement required. All has worked fine since then.
HTH
Tom

3825 FXO Port remains in off-hook after call

Hello,
I have a 3825 router with 8 FXO ports running Cisco IOS Software, 3800 Software (C3825-SPSERVICESK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2). The problem we are facing is that after a call is placed through any of the FXO ports and the call is ended by the user, the port remains in off-hook till a reset of the port is done or someone restarts the router. Only then is the port accessible again.
I am thinking of changing the cards, but i do not want to invest in replacing the cards and then find out that this doesnt solve the problem.
The wierd thing is that this issue started on its own accord not too long ago.
Comments and suggestions please!
Regards,
Femi

Hello,
I do not want to change the FXO card till I am sure that is the problem and I did state that I always have to reboot the router when the problem starts. Rebooting clears the problem but it is back immediately I attempt a call again and hang up that call.
I have timeouts call-disconnect already configured, see below:
voice-port 0/0/0
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/0/1
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 2626878
caller-id enable type 1
voice-port 0/0/2
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/0/3
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/0
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/1
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/2
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/3
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
Regards,
Femi

2900 FXO Port remains in off-hook after call

Hello
I have a 2900 router with FXO ports running Cisco IOS Software
c2900-universalk9-mz.SPA.151-4.M5.bin .
The problem is when the call is ended and we hung-up, port remains in off-hook and the line remains busy for long time.

CUCM 8.6.2.23900-10
Do you need all configuration or voice port?
voice-port 0/0/0
trunk-group PSTN
cptone IL
timeouts call-disconnect 1
timeouts wait-release 1
connection plar 58694150
impedance complex2
caller-id enable
voice-port 0/0/1
trunk-group PSTN
cptone IL
timeouts call-disconnect 1
timeouts wait-release 1
connection plar 58694151
impedance complex2
caller-id enable
voice-port 0/0/2
trunk-group PSTN
cptone IL
timeouts call-disconnect 1
timeouts wait-release 1
connection plar 58694152
impedance complex2
caller-id enable

FXS stay in off-hook

Hi All,
I have an issue for fxs port in voice gateway, the fxs port connceted to the fax machine is in off-hook state. it will change to on hook when i unplug the phone cable.
IOS Version : C2951-UNIVERSALK9-M version 15.2(4)M5.
H323 voice gateway.
shut and no shut on voice port, no any changes. please see attached picture.
Can someone please tell whether this is due to any IOS bug?

Now it's status is changed to on-hook, if i enter command " csim start 803" to test, the status will change to off-hook, but when i place a call from jabber to 803, the status is not changed, the status is still on-hook, maybe something is wrong on router?
I captured log on RTMT, please see bellow:
2014/09/13 11:25:53.294|SIPL|0|TCP|IN|192.168.100.11|5060|CSFReceptionist|192.168.100.17|1900|1,100,13,332.56^192.168.100.17^*|6952|[email protected]|INVITE
2014/09/13
11:25:53.295|SIPL|0|TCP|OUT|192.168.100.11|5060|CSFReceptionist|192.168.100.17|1900|1,100,13,332.56^192.168.100.17^*|6953|[email protected]|100 Trying
2014/09/13 11:25:53.304|SIPL|21471657|TCP|OUT|192.168.100.11|5060|CSFReceptionist|192.168.100.17|1900|1,100,13,1.836^*^*|6954|[email protected]|183 Session Progress
2014/09/13 11:26:02.631|SIPL|21471657|TCP|OUT|192.168.100.11|5060|CSFReceptionist|192.168.100.17|1900|1,100,13,305.193^192.168.100.11^ANN_2|6955|[email protected]|404 Not Found
2014/09/13 11:26:02.632|SIPL|21471657|TCP|IN|192.168.100.11|5060|CSFReceptionist|192.168.100.17|1900|1,100,13,332.57^192.168.100.17^*|6956|[email protected]|ACK
2014/09/13 11:26:02.633|CC|REJECT|21471657|21471658|221|803|803|1
i user jabber for desktop(221) to call 803, it is rejected.
Any helps would be appreciated.

Unity connections 9.1 "port stuck with call"

I am seeing this message in the error log: %UC_UCEVNT-3-EvtMiuPortStuckWithCallinfoOnly: for a number of ports. . When I look into the log some of these ports have ben up for a month .
the message is cleared by restarting the port,
This stuck port problem has been around for a long time we had it in ver 7.1, is there any way of making a port reset if it has been stuck on a call for say 24 hours?

Hello chrbradf1,
You can set the amount of time for the watchdog to generate a log when the port would be considered locked, but there is no automatic way of restarting them on the CUC perspective neither on CUCM, there is also no provisioning for Tcl scripting therefore you will have to restart them manually.
Watchdog is under: Cisco Unity Connection Administration> System Settings> Advanced> Telephonny> Port Watchdog Threshold in Minutes.
Port Watchdog Threshold in Minutes
Enter the time, in minutes, that a port can be off hook before it is considered to be locked. When a port reaches this threshold, Cisco Unity Connection logs an error. To review errors, see the Real-Time Monitoring Tool. We recommend a setting greater than 30 minutes.
Default setting: 240 minutes.
http://www.cisco.com/en/US/docs/voice_ip_comm/connection/8x/gui_reference/guide/8xcucgrg110.html
Also consider that maximum time is 240000 minimum is 0 and value has to be integer.
Examples:
Value specified (111111111) exceeds the maximum allowable value (24000).
Value specified (0.1111) is not an integer value
Value specified (-1111) is below the minimum allowable value (0).
-David

Fxs ports state unknown cisco 1861

Hello ,
Cisco router 1861 the ports are unkown state .
I tried 'mgcp' 'no mgcp'
show ccm
Primary         Registered               172.26.4.2
First Backup    Backup Ready             172.26.4.1
Second Backup   None
Current active Call Manager:    172.26.4.2
Backhaul/Redundant link port:   2428
Failover Interval:              30 seconds
Keepalive Interval:             15 seconds
Last keepalive sent:            09:44:49 UTC Dec 25 2013 (elapsed time: 00:00:13)
Last MGCP traffic time:         09:44:49 UTC Dec 25 2013 (elapsed time: 00:00:13)
Last failover time:             11:30:26 UTC Dec 22 2013 from (172.26.4.2)
Last switchback time:           11:31:11 UTC Dec 22 2013 from (172.26.4.1)
Switchback mode:                Immediate
MGCP Fallback mode:             Enabled/OFF
Last MGCP Fallback start time: 04:54:21 UTC Dec 8 2013
Last MGCP Fallback end time:    11:25:42 UTC Dec 22 2013
MGCP Download Tones:            Disabled
TFTP retry count to shut Ports: 2
FAX mode: disable
Configuration Error History:
store179#show mgcp endpoint
aaln/S0/SU0/0@store179
aaln/S0/SU0/1@store179
aaln/S0/SU0/2@store179
aaln/S0/SU0/3@store179
aaln/S0/SU1/1@store179
PORT            CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
=============== == ============ ===== ==== ======== ======== ==
0/0/0           -- fxs-ls      up    dorm on-hook idle     y
0/0/1           -- fxs-ls      up    dorm on-hook idle     y
0/0/2           -- fxs-ls      up    dorm on-hook idle     y
0/0/3           -- fxs-ls      up    dorm on-hook idle     y
0/1/0           -- fxo-ls      up    down idle     off-hook y
PORT            CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
=============== == ============ ===== ==== ======== ======== ==
0/0/0           -- fxs-ls      up    dorm on-hook idle     y
0/0/1           -- fxs-ls      up    dorm on-hook idle     y
0/0/2           -- fxs-ls      up    dorm on-hook idle     y
0/0/3           -- fxs-ls      up    dorm on-hook idle     y
0/1/0           -- fxo-ls      up    down idle     off-hook y
I have dial-peers for the ports .
Any ideas ?

Debug mgcp packets
*Dec 25 13:13:25.808: MGCP Packet sent to 172.26.4.2:2427--->
NTFY 257951726 *@store179.super-pharm.co.il MGCP 0.1
X: 0
O:
<---
*Dec 25 13:13:25.820: MGCP Packet received from 172.26.4.2:2427--->
200 257951726
<---
conf t
Enter configuration commands, one per line. End with CNTL/Z.
store179(config)#no mgcp
WARNING: no mgcp: Teardown MGCP application may take a while to clean up resources
store179(config)#
*Dec 25 13:13:36.220: MGCP Packet sent to 172.26.4.2:2427--->
RSIP 257951727 *@store179.super-pharm.co.il MGCP 0.1
RM: graceful
RD: 0
<---
*Dec 25 13:13:36.228: %MGCP_APP-6-MGCP_SHUTDOWN_COMPLETE: MGCP Shutdown has completed
mgcp
store179(config)#
*Dec 25 13:13:46.980: MGCP Packet sent to 172.26.4.2:2427--->
RSIP 257951729 *@store179.super-pharm.co.il MGCP 0.1
RM: restart
<---
*Dec 25 13:13:47.004: MGCP Packet received from 172.26.4.2:2427--->
200 257951729
<---
*Dec 25 13:13:47.008: MGCP Packet received from 172.26.4.2:2427--->
RQNT 34773851 AALN/S0/SU0/[email protected] MGCP 0.1
X: 2
R: L/hd
Q: process,loop
<---
*Dec 25 13:13:47.008: MGCP Packet sent to 172.26.4.2:2427--->
200 34773851 OK
<---
*Dec 25 13:13:47.008: MGCP Packet received from 172.26.4.2:2427--->
RQNT 34773852 AALN/S0/SU0/[email protected] MGCP 0.1
X: 2
R: L/hd
Q: process,loop
<---
*Dec 25 13:13:47.012: MGCP Packet sent to 172.26.4.2:2427--->
200 34773852 OK
<---
*Dec 25 13:13:47.012: MGCP Packet received from 172.26.4.2:2427--->
RQNT 34773853 AALN/S0/SU0/[email protected] MGCP 0.1
X: 2
R: L/hd
Q: process,loop
<---
*Dec 25 13:13:47.012: MGCP Packet sent to 172.26.4.2:2427--->
200 34773853 OK
<---
*Dec 25 13:13:47.012: MGCP Packet received from 172.26.4.2:2427--->
RQNT 34773854 AALN/S0/SU1/[email protected] MGCP 0.1
X: 0
R: L/hd
Q: process,loop
<---
*Dec 25 13:13:47.016: MGCP Packet sent to 172.26.4.2:2427--->
200 34773854 OK
<---
*Dec 25 13:13:47.016: MGCP Packet received from 172.26.4.2:2427--->
RQNT 34773855 AALN/S0/SU0/[email protected] MGCP 0.1
X: 2
R: L/hd
Q: process,loop
<---
*Dec 25 13:13:47.016: MGCP Packet sent to 172.26.4.2:2427--->
200 34773855 OK
<---
*Dec 25 13:13:47.020: MGCP Packet sent to 172.26.4.2:2427--->
NTFY 257951731 *@store179.super-pharm.co.il MGCP 0.1
X: 0
O:
<---
*Dec 25 13:13:47.020: MGCP Packet received from 172.26.4.2:2427--->
AUEP 34773856 AALN/S0/SU0/[email protected] MGCP 0.1
F: X, A, I
<---
*Dec 25 13:13:47.024: MGCP Packet sent to 172.26.4.2:2427--->
200 34773856
I:
X: 2
L: p:10-20, a:PCMU;PCMA;G.nX64, b:64, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-220, a:G.729;G.729a;G.729b, b:8, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-110, a:G.726-16;G.728, b:16, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-70, a:G.726-24, b:24, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-50, a:G.726-32, b:32, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-270, a:G.723.1-H;G.723;G.723.1a-H, b:6, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-330, a:G.723.1-L;G.723.1a-L, b:5, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
M: sendonly, recvonly, sendrecv, inactive, loopback, conttest, data, netwloop, netwtest
<---
*Dec 25 13:13:47.024: MGCP Packet received from 172.26.4.2:2427--->
AUEP 34773857 AALN/S0/SU0/[email protected] MGCP 0.1
F: X, A, I
<---
*Dec 25 13:13:47.024: MGCP Packet sent to 172.26.4.2:2427--->
200 34773857
I:
X: 2
L: p:10-20, a:PCMU;PCMA;G.nX64, b:64, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-220, a:G.729;G.729a;G.729b, b:8, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-110, a:G.726-16;G.728, b:16, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-70, a:G.726-24, b:24, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-50, a:G.726-32, b:32, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-270, a:G.723.1-H;G.723;G.723.1a-H, b:6, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-330, a:G.723.1-L;G.723.1a-L, b:5, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
M: sendonly, recvonly, sendrecv, inactive, loopback, conttest, data, netwloop, netwtest
<---
*Dec 25 13:13:47.028: MGCP Packet received from 172.26.4.2:2427--->
AUEP 34773858 AALN/S0/SU0/[email protected] MGCP 0.1
F: X, A, I
<---
*Dec 25 13:13:47.028: MGCP Packet sent to 172.26.4.2:2427--->
200 34773858
I:
X: 2
L: p:10-20, a:PCMU;PCMA;G.nX64, b:64, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-220, a:G.729;G.729a;G.729b, b:8, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-110, a:G.726-16;G.728, b:16, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-70, a:G.726-24, b:24, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-50, a:G.726-32, b:32, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-270, a:G.723.1-H;G.723;G.723.1a-H, b:6, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-330, a:G.723.1-L;G.723.1a-L, b:5, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
M: sendonly, recvonly, sendrecv, inactive, loopback, conttest, data, netwloop, netwtest
<---
*Dec 25 13:13:47.028: MGCP Packet received from 172.26.4.2:2427--->
AUEP 34773859 AALN/S0/SU1/[email protected] MGCP 0.1
F: X, A, I
<---
*Dec 25 13:13:47.032: MGCP Packet sent to 172.26.4.2:2427--->
200 34773859
I:
X: 0
L: p:10-20, a:PCMU;PCMA;G.nX64, b:64, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-220, a:G.729;G.729a;G.729b, b:8, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-110, a:G.726-16;G.728, b:16, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-70, a:G.726-24, b:24, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-50, a:G.726-32, b:32, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-270, a:G.723.1-H;G.723;G.723.1a-H, b:6, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-330, a:G.723.1-L;G.723.1a-L, b:5, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
M: sendonly, recvonly, sendrecv, inactive, loopback, conttest, data, netwloop, netwtest
<---
*Dec 25 13:13:47.032: MGCP Packet received from 172.26.4.2:2427--->
AUEP 34773860 AALN/S0/SU0/[email protected] MGCP 0.1
F: X, A, I
<---
*Dec 25 13:13:47.032: MGCP Packet sent to 172.26.4.2:2427--->
200 34773860
I:
X: 2
L: p:10-20, a:PCMU;PCMA;G.nX64, b:64, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-220, a:G.729;G.729a;G.729b, b:8, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-110, a:G.726-16;G.728, b:16, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-70, a:G.726-24, b:24, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-50, a:G.726-32, b:32, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-270, a:G.723.1-H;G.723;G.723.1a-H, b:6, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-330, a:G.723.1-L;G.723.1a-L, b:5, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
M: sendonly, recvonly, sendrecv, inactive, loopback, conttest, data, netwloop, netwtest
<---
*Dec 25 13:13:47.036: MGCP Packet received from 172.26.4.2:2427--->
200 257951731
<---
*Dec 25 13:13:48.004: MGCP Packet sent to 172.26.4.2:2427--->
RSIP 257951728 *@store179.super-pharm.co.il MGCP 0.1
RM: restart
<---
*Dec 25 13:13:48.036: MGCP Packet received from 172.26.4.2:2427--->
200 257951728
<---
store179(config)#
store179(config)#
store179(config)#
store179(config)#
store179(config)#
store179(config)#
store179(config)#u all
                  ^
% Invalid input detected at '^' marker.
store179(config)#exit
store179#
*Dec 25 13:14:02.016: MGCP Packet sent to 172.26.4.2:2427--->
NTFY 257951732 *@store179.super-pharm.co.il MGCP 0.1
X: 0
O:
<---
*Dec 25 13:14:02.032: MGCP Packet received from 172.26.4.2:2427--->
200 257951732
it's not possiable to do the other debugs they stuck the router

SPA2102 FXS port state monitoring

Hi all,
Is there any way to get FXS port state for LinkSys SPA2102 VoIP adapter (i.e. is there a phone that connected to it or not) remotely, for example, via SNMP ?
Thanks.

Here's the bug ID: CSCse15025
Doubt the NM is faulty - we had the same issue in a 2821 and migrated to 12.4(4)T4 to correct it. No hardware replacement required. All has worked fine since then.
HTH
Tom

GigE port stuck in init state on SSN-16

I have a Cisco MDS 9222i running NX-OS 6.2(3) with a SSN-16 module in slot 2. One of the GigE ports with an active connection to a FEX remains in the "init" state. Shutting and no shutting the port doesn't change the state. When I move the SFP and cable from the problematic port to another port it comes up immediately. Has anybody heard of this problem?

Hi,
Are you seeing hellos across the link (debug ip ospf hello)? If so, please check the MTU settings on both interfaces and set the OSPF link type (point-to-point).
If there are no OSPF hellos received you have to ask your provider to troubleshoot the problem with you. In principle it should work.
Hope this helps!
Regards, Martin

FXS Port Query?

Hi,
We are running VoIPovFR to a remote location, which has 2 x 4FXS/DID module installed into a C2621XM chassis. We are using IOS c2600-is-mz.122-15.
Out of the 8 ports, two continually go off-hook, FXSLS_WAIT_OFFHOOK before finally going into a FXSLS_PARK state. I have moved the cabling and the error occurs on which ever port the two lines plugs into.
Has anyone ever see this before. To my mind it looks like a cabling issue?
Any ideas?
Thanks

Try wiring all FXS ports like this
FXS PORT 0 RJ11 3-----------------------A ANALOGUE
FXS PORT 0 RJ11 4-----------------------B PHONE
FXS PORT 1 RJ11 3-----------------------A ANALOGUE
FXS PORT 1 RJ11 4-----------------------B PHONE
FXS PORT 2 RJ11 3-----------------------A ANALOGUE
FXS PORT 2 RJ11 4-----------------------B PHONE
FXS PORT 3 RJ11 3-----------------------A ANALOGUE
FXS PORT 3 RJ11 4-----------------------B PHONE
Ensure that all other wires are left disconnected

SPA9000 Configuration Issue with FXS Port(s)

Successfully configured SPA9000 PBX with two VoIP providers setting Voice->Line 1/2 parameters. One phone set is connected to FXS 1 (or FXS 2) port and able to chose the proper VoIP provider when making outbound calls.
Issue is that once outbound call is established, SPA9000 is not responding to additional numbers dialled for called party extension number. Same issue when dialling a number where voice prompt answers the call offering selection of activities to be chosen by dialling specific number. None of the entered selection works as nothing is entered on the dial.
Located in Canada. VoIP providers: freephoneline.ca & callcentric.com
SPA9000 configuration:
Software version: 6.1.5; Hardware version: 1.0.5(a)
Voice -> SIP -> PBX Parameters -> Call Routing Rule: (<:L1>9xx. | <:L2>8xx.)
Voice -> SIP -> PBX Phone Parameters -> Phone Dial Plan: ([89],[3469]11S0 | [89],1[2-9]xxxxxxxxxS0 | [89],011xx. | [89],xx.)
Voice -> FXS 1/2 -> Dial Plan: ([89],[3469]11S0 | [89],1[2-9]xxxxxxxxxS0 | [89],011xx. | [89],xx.)
Voice -> Line 1 -> Dial Plan: (<9:>xx.)
Voice -> Line 2 -> Dial Plan: (<8:>xx.)
Voice -> Regional -> Call Progress Tones:
Dial Tone: 350@-19,440@-19;10(*/0/1+2)
Second Dial Tone: 420@-19,520@-19;10(*/0/1+2)
Outside Dial Tone: 420@-16;10(*/0/1)
Prompt Tone: 520@-19,620@-19;10(*/0/1+2)
Busy Tone: 480@-19,620@-19;10(.5/.5/1+2)
Reorder Tone: 480@-19,620@-19;10(.25/.25/1+2)
Off Hook Warning Tone: 480@-10,620@0;10(.125/.125/1+2)
Ring Back Tone: 440@-19,480@-19;*(2/4/1+2)
Confirm Tone: 600@-16;1(.25/.25/1)
SIT1 Tone: 985@-16,1428@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/3,0/4/0)
SIT2 Tone: 914@-16,1371@-16,1777@-16;20(.274/0/1,.274/0/2,.380/0/3,0/4/0)
SIT3 Tone: 914@-16,1371@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/3,0/4/0)
SIT4 Tone: 985@-16,1371@-16,1777@-16;20(.380/0/1,.274/0/2,.380/0/3,0/4/0)
MWI Dial Tone: 350@-19,440@-19;2(.1/.1/1+2);10(*/0/1+2)
Cfwd Dial Tone: 350@-19,440@-19;2(.2/.2/1+2);10(*/0/1+2)
Holding Tone: 600@-19;*(.1/.1/1,.1/.1/1,.1/9.5/1)
Conference Tone: 350@-19;20(.1/.1/1,.1/9.7/1)
Secure Call Indication Tone: 397@-19,507@-19;15(0/2/0,.2/.1/1,.1/2.1/2)
Feature Invocation Tone: 350@-16;*(.1/.1/1)

Hi @sglumac, it seems that your SPA9000 is a Cisco product. Please repost this to this link: https://supportforums.cisco.com/ for solutions.

Connection PLAR on FXS port 2821

I have an anlog phone that is located by the main gate. The phone has been extended and terminated into an FXS port on a 2821 router. I am trying to configure a connect PLAR on he FXS port, so that when the phone goes off-hook it dials an internal VoIP extension.
I am not having any luck. Any help would be appreciated. My config is below:
voice-port 1/0/5
timing hookflash-in 50 0
connection plar 220005
description North gate
caller-id enable
dial-peer voice 220005 pots
destination-pattern 220005
port 1/0/5
dial-peer voice 100 voip
preference 1
destination-pattern 220...
modem passthrough nse codec g711ulaw
session target dns:CallAgent01
voice-class codec 1
voice-class h323 1
dtmf-relay h245-alphanumeric
no vad
Thanks!!
Jaime

Yosh - do I need to remove dial-peer voice 220005 pots for the PLAR to work correctly?
Thanks,
Jaime

EEM script that generates only 1 email when a fxs port is offhook.

Using the below config I am able to receive a email anytime my voice port is in any other state than ON HOOK. The problem I have is the script runs every 30 seconds and I receive an email every 30 seconds the line is in any other state than "ON-HOOK".
Is there a way to have only one email generated ONLY when the state changes from the previous state?
example : the line is on-hook, changes to off-hook or park or whatever- a email would be generated. ( only One email). not one every 30 seconds...
The line goes from Off-Hook back to IDLE. - A email would be generated to advise the line has been restored to a IDLE state.
I know what you're thinking why? Well I was thinking of using the analog ports as kind of a poor man's slightly intelligent surveillance system. If port 1/0/0 goes off hook or shorted, then this is an alarm condition. A email would be generated. I just don't need a email every 30 seconds.
scheduler allocate 20000 1000
event manager environment _email_from [email protected]
event manager environment _email_to email [email protected]
event manager environment _email_server smtp-server.isp.net
event manager applet check_1/0/0_if_NOT_ONHOOK
event timer watchdog time 30
action 001 cli command "enable"
action 002 cli command "show voice port summ | include 1/0/0"
action 003 foreach line "$_cli_result" "\n"
action 004 regexp "on-hook" "$line"
action 005 if $_regexp_result eq "1"
action 006 exit 0
action 007 end
action 008 end
action 009 syslog msg "PORT_1_is_in_any_other_state_then_on-HooK!"
action 1.0 mail server "$_email_server" to "$_email_to" from "$_email_from" subject "$_event_pub_time:Test EEM port 1/0/0 is SHORTED ie IN ALARM" body "TEST Body"
end
Any ideas?

Look at EEM context to save the value of a variable across policy runs. So you could retrieve the value of the context and compare it to the current value, if they are different then send an email and if they are the same then no action.
http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/eem/command/eem-cr-book/eem-cr-a1.html#wp2399063000
The first time your updated policy runs and executes the context retrieve there will not be a value since you have to do a context save first. To get around this make a second policy that runs at reboot to do a context save of the "on-hook" state.

PAP2T - some devices cannot go off-hook to dial

Not sure if this is the right place for Linksys VOIP hardware - though Cisco moved everything onto their site...
I have a PAP2T that seems to have trouble letting some analog devices dial out. Specifically, I tried it with a credit-card machine, and it seemed like the PAP2T would never go off-hook so it could dial. I saw no SIP traffic for any dialing. However, I immediately plugged the same FXS port into a fax machine, and that fax machine was able to dial out fine.

Before you set up port forwarding on your router, change two of the Phone Adapter's settings using its Interactive Voice Response Menu. First, disable its DHCP feature, then assign a static IP address to the Phone Adapter.

FXS Port stucks in Off-Hook state on NM-HDA

Similar Messages

Maybe you are looking for