VG224 port stuck in 'off-hook' state

Hi All,
I have strange problem with my VG224 connected to CME4.0.
I have 1 port have no dial tone. And 'show voice port sum' result
VG1050005#sh voice port sum
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
============== == ============ ===== ==== ======== ======== ==
2/2 -- fxs-ls up dorm off-hook idle y
ADMIN is UP, OPER is DORM, but IN STATUS is OFF-HOOK
VPM STATE from 'sh voice call sum' is FXSLS_ONHOOK
I have already shutdown this port and reload the VG224 and unplug the analog phone. But no effect.
FYI, Im running IOS version 12.4(9)T1 for VG224.
Any solution for this problem?
Thanks.
Iwan

Configuration for VG
======================
stcapp ccm-group 1
stcapp
stcapp feature access-code
prefix *#
voice-card 0
interface FastEthernet0/0
ip address 10.102.1.35 255.255.255.0
duplex auto
speed auto
voice-port 2/2
cptone ID
timeouts call-disconnect 2
timing hookflash-in 500 150
sccp local FastEthernet0/0
sccp ccm 10.102.1.12 identifier 10 version 4.0
sccp
sccp ccm group 1
associate ccm 10 priority 1
dial-peer voice 3 pots
service stcapp
port 2/2
=========================
This port work well for 2 weeks before this problem happen. Another port have same configuration and its working

Similar Messages

FXS Port stucks in Off-Hook state on NM-HDA

Hi,
i have some trouble with an FXS Port on an NM-HDA which stucks in the Off-Hook state, after some time of normal operation. The Voice-Port is in Off-Hook state regardless of if there is an Enddevice attached or not. Even an reload of the router does not help.
The voice port is configured for loop-start. The NM-HDA is housed in an Cisco 3725 running IOS Vers. 12.3(14)T2 with H.323 signalling.
Is there anybody who has seen this before? Could this be caused by an IOS-Bug or is it more likley that the NM-HDA is faulty?
Regards
Robert

Here's the bug ID: CSCse15025
Doubt the NM is faulty - we had the same issue in a 2821 and migrated to 12.4(4)T4 to correct it. No hardware replacement required. All has worked fine since then.
HTH
Tom

3825 FXO Port remains in off-hook after call

Hello,
I have a 3825 router with 8 FXO ports running Cisco IOS Software, 3800 Software (C3825-SPSERVICESK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2). The problem we are facing is that after a call is placed through any of the FXO ports and the call is ended by the user, the port remains in off-hook till a reset of the port is done or someone restarts the router. Only then is the port accessible again.
I am thinking of changing the cards, but i do not want to invest in replacing the cards and then find out that this doesnt solve the problem.
The wierd thing is that this issue started on its own accord not too long ago.
Comments and suggestions please!
Regards,
Femi

Hello,
I do not want to change the FXO card till I am sure that is the problem and I did state that I always have to reboot the router when the problem starts. Rebooting clears the problem but it is back immediately I attempt a call again and hang up that call.
I have timeouts call-disconnect already configured, see below:
voice-port 0/0/0
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/0/1
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 2626878
caller-id enable type 1
voice-port 0/0/2
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/0/3
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/0
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/1
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/2
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/3
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
Regards,
Femi

WRP400 hangs in off hook state

Hello,
we have a client which uses WRP400 for T.38 faxing. It has modem connected to FXS port. Usually every 2weeks WRP400 hangs in 'off hook' state for that FXS port and no reboot helps to fix that. Only after firmware rewrite line hook gets in place. We use 1.00.06 version of firmware. Any thoughts on a problem?

Here's the bug ID: CSCse15025
Doubt the NM is faulty - we had the same issue in a 2821 and migrated to 12.4(4)T4 to correct it. No hardware replacement required. All has worked fine since then.
HTH
Tom

2900 FXO Port remains in off-hook after call

Hello
I have a 2900 router with FXO ports running Cisco IOS Software
c2900-universalk9-mz.SPA.151-4.M5.bin .
The problem is when the call is ended and we hung-up, port remains in off-hook and the line remains busy for long time.

CUCM 8.6.2.23900-10
Do you need all configuration or voice port?
voice-port 0/0/0
trunk-group PSTN
cptone IL
timeouts call-disconnect 1
timeouts wait-release 1
connection plar 58694150
impedance complex2
caller-id enable
voice-port 0/0/1
trunk-group PSTN
cptone IL
timeouts call-disconnect 1
timeouts wait-release 1
connection plar 58694151
impedance complex2
caller-id enable
voice-port 0/0/2
trunk-group PSTN
cptone IL
timeouts call-disconnect 1
timeouts wait-release 1
connection plar 58694152
impedance complex2
caller-id enable

FXS stay in off-hook

Hi All,
I have an issue for fxs port in voice gateway, the fxs port connceted to the fax machine is in off-hook state. it will change to on hook when i unplug the phone cable.
IOS Version : C2951-UNIVERSALK9-M version 15.2(4)M5.
H323 voice gateway.
shut and no shut on voice port, no any changes. please see attached picture.
Can someone please tell whether this is due to any IOS bug?

Now it's status is changed to on-hook, if i enter command " csim start 803" to test, the status will change to off-hook, but when i place a call from jabber to 803, the status is not changed, the status is still on-hook, maybe something is wrong on router?
I captured log on RTMT, please see bellow:
2014/09/13 11:25:53.294|SIPL|0|TCP|IN|192.168.100.11|5060|CSFReceptionist|192.168.100.17|1900|1,100,13,332.56^192.168.100.17^*|6952|[email protected]|INVITE
2014/09/13
11:25:53.295|SIPL|0|TCP|OUT|192.168.100.11|5060|CSFReceptionist|192.168.100.17|1900|1,100,13,332.56^192.168.100.17^*|6953|[email protected]|100 Trying
2014/09/13 11:25:53.304|SIPL|21471657|TCP|OUT|192.168.100.11|5060|CSFReceptionist|192.168.100.17|1900|1,100,13,1.836^*^*|6954|[email protected]|183 Session Progress
2014/09/13 11:26:02.631|SIPL|21471657|TCP|OUT|192.168.100.11|5060|CSFReceptionist|192.168.100.17|1900|1,100,13,305.193^192.168.100.11^ANN_2|6955|[email protected]|404 Not Found
2014/09/13 11:26:02.632|SIPL|21471657|TCP|IN|192.168.100.11|5060|CSFReceptionist|192.168.100.17|1900|1,100,13,332.57^192.168.100.17^*|6956|[email protected]|ACK
2014/09/13 11:26:02.633|CC|REJECT|21471657|21471658|221|803|803|1
i user jabber for desktop(221) to call 803, it is rejected.
Any helps would be appreciated.

Unity connections 9.1 "port stuck with call"

I am seeing this message in the error log: %UC_UCEVNT-3-EvtMiuPortStuckWithCallinfoOnly: for a number of ports. . When I look into the log some of these ports have ben up for a month .
the message is cleared by restarting the port,
This stuck port problem has been around for a long time we had it in ver 7.1, is there any way of making a port reset if it has been stuck on a call for say 24 hours?

Hello chrbradf1,
You can set the amount of time for the watchdog to generate a log when the port would be considered locked, but there is no automatic way of restarting them on the CUC perspective neither on CUCM, there is also no provisioning for Tcl scripting therefore you will have to restart them manually.
Watchdog is under: Cisco Unity Connection Administration> System Settings> Advanced> Telephonny> Port Watchdog Threshold in Minutes.
Port Watchdog Threshold in Minutes
Enter the time, in minutes, that a port can be off hook before it is considered to be locked. When a port reaches this threshold, Cisco Unity Connection logs an error. To review errors, see the Real-Time Monitoring Tool. We recommend a setting greater than 30 minutes.
Default setting: 240 minutes.
http://www.cisco.com/en/US/docs/voice_ip_comm/connection/8x/gui_reference/guide/8xcucgrg110.html
Also consider that maximum time is 240000 minimum is 0 and value has to be integer.
Examples:
Value specified (111111111) exceeds the maximum allowable value (24000).
Value specified (0.1111) is not an integer value
Value specified (-1111) is below the minimum allowable value (0).
-David

GigE port stuck in init state on SSN-16

I have a Cisco MDS 9222i running NX-OS 6.2(3) with a SSN-16 module in slot 2. One of the GigE ports with an active connection to a FEX remains in the "init" state. Shutting and no shutting the port doesn't change the state. When I move the SFP and cable from the problematic port to another port it comes up immediately. Has anybody heard of this problem?

Hi,
Are you seeing hellos across the link (debug ip ospf hello)? If so, please check the MTU settings on both interfaces and set the OSPF link type (point-to-point).
If there are no OSPF hellos received you have to ask your provider to troubleshoot the problem with you. In principle it should work.
Hope this helps!
Regards, Martin

"Phone off-hook" HP Officejet Pro 8500 Wireless, Product CB023A

I have a HP Officejet Pro 8500 wireless printer/fax/copier all in one.
The message "phone off-hook" appears on my display.
I ran the Fax Test and received a PASS for all results.
A few minutes later, a message appeared on the printer/fax display: "Turn power off, then on again". I did so.
This message, "Turn power off, then on again" continues to repeat and after I turn power off then on, the "phone off-hook" displays again. It is an endless loop of receiving these two messages.
I also did the following:
1. Unplugged the telephone fax line from LINE of the Officejet Pro.
2. Unplugged the power cord to the printer.
3. Replugged the power cord to the printer.
4. Powered up the printer
5. After powering up, the message, "phone off-hook" reappears.
I ran the fax test
Run Fax Test:
1. select Tools from HP Officejet Pro 8500 wireless display panel.
2. Select Run Fax Test
Results:
Fax Hardware Test ........................................................ PASS
Fax Connected to Active Telephone Wall Jack ......... PASS
Phone Cord Connected to Correct Port on Fax ........ PASS
Using Correct Type of Phone Cord with Fax ............. PASS
Dial Tone Detection ....................................................... PASS
Fax Line Condition Test ................................................ PASS
3. The message still appears.
My printer description is as follows:
- Model No. : A909G (look inside of the ink access door); Regulatory Model No. : SNPRC-0703-02
- Product No. : CB023A
- Serial No. CN0737R2DH
Is the printer defective? What should I do to correct this problem?
Thanks,
ArtLaw

Hello ArtLaw,
If you have followed all the troubleshooting steps outlined in this troubleshooting article then the only other solution is to have the printer serviced as it may be a printer hardware issue.
Troubleshooting 'Phone Off Hook' Front Panel Messages
If I have helped you in any way click the Kudos button to say Thanks.
The community works together, click Accept as Solution on the post that solves your issue for other members of the community to benefit from the solution.
- Friendship is magical.

PAP2T - some devices cannot go off-hook to dial

Not sure if this is the right place for Linksys VOIP hardware - though Cisco moved everything onto their site...
I have a PAP2T that seems to have trouble letting some analog devices dial out. Specifically, I tried it with a credit-card machine, and it seemed like the PAP2T would never go off-hook so it could dial. I saw no SIP traffic for any dialing. However, I immediately plugged the same FXS port into a fax machine, and that fax machine was able to dial out fine.

Before you set up port forwarding on your router, change two of the Phone Adapter's settings using its Interactive Voice Response Menu. First, disable its DHCP feature, then assign a static IP address to the Phone Adapter.

ATA186 makes fax machine constantly off hook

Hello
First post!
I have a Cisco ATA 186 that is connected to a HP officejet 4500 all-in-one fax/printer. The ATA is configured properly, I did connect a "higher end" fax machine and was able to dial out and in (with in the system)
this particular fax does not have a "hook" option. The display reads "phone off hook" all the time. The manual (yes I read it) states that there is an adapter that shoudl be used or the machine will read "phone off hook" all the time. This did not solve the problem.
I think the ATA always give a dial tone without being asked for it. IOW, the fax does not say "hey give me a dial tone please".
Is there a way of the ATA providing a dial tone when asked? Or maybe the fax is incompatible?
Thank you for your help....

This is my suggestion:
- check if the telephony cable has only 1 couple of wire (tip and ring only); in the past I had some problems with cable with 4 wire (2 couple); the ATA had a strange behavior;
- try to connect an analog telephone to the ATA186 and verify if it works;
- if the problem persists probably the ATA has an hardware fault;
- try with a different ATA;
Best Regards.

Can't print off my statements like before...have to print one page at a time instead of whole statement...what gives? did up dates ...updates no good?

Can't print off my statements like I did before...have to print one page at a time now...what happened? never had proble before....I did an update that they said was available...did that cause the problem...Apple???

Hi Charlott...
Open System Preferences > Print & Scan then select the Print tab.
Click: Open Print Queue...
Delete all documents in the queue
Restart your Mac, turn off the printer then turn it back on then try printing.
Not sure which update you are referring to. If you have Lion installed and updated to v10.7.3, I doubt that had any effect on printing.
BTW... when you post, please tell us which Mac OS X you have installed. Thanks!

HP Officejet Pro 8500 "phone off hook"

HP Officejet Pro 8500 panel shows "phone off hook" and faxes will not come in and it is on a dedicated phone line. I can send out without any problem. The telephone technician determined the problem is not with the phone service.

I need to send a fax and I can not do it
Please what can Ido to fix it.
Thanhs, Francisco

CUCM AXL Query Phone Off-hook Status

Hi
For SOAP/AXL query purposes, does anyone know the table(s) and field(s) within CUCM v7.0 to query a phones' off-hook status? I've had a look through the database dictionary, but could not see anything obviously relating to 'off-hook' or busy. I'm looking to put together a query to find out which users are currently busy taking calls.
In addition, some of our phones are configured with extension mobility, so not sure whether the query should be focussed on the device profile or line appearance rather than physical handset.
Any help appreciated!
Thanks
Yves

Hello John,
You may try to use BLF.
This is not supported with CCA.
HTH,
Alex
*Please rate helpful posts

Differentiate between DND and "Off Hook" status

We have several directors and assistants on staff where it would be helpful to the assistant if their phone displayed and differentiated between off hook or dnd. Currently, both off hook status and dnd report the same indicator for the assistant.
UC560 environment, ip phone 514G and 7965G
Thanks for the help.
Blessings,
John J

Hello John,
You may try to use BLF.
This is not supported with CCA.
HTH,
Alex
*Please rate helpful posts

VG224 port stuck in 'off-hook' state

Similar Messages

Maybe you are looking for