Fxs ports state unknown cisco 1861

Hello ,
Cisco router 1861 the ports are unkown state .
I tried 'mgcp' 'no mgcp'
show ccm
Primary         Registered               172.26.4.2
First Backup    Backup Ready             172.26.4.1
Second Backup   None
Current active Call Manager:    172.26.4.2
Backhaul/Redundant link port:   2428
Failover Interval:              30 seconds
Keepalive Interval:             15 seconds
Last keepalive sent:            09:44:49 UTC Dec 25 2013 (elapsed time: 00:00:13)
Last MGCP traffic time:         09:44:49 UTC Dec 25 2013 (elapsed time: 00:00:13)
Last failover time:             11:30:26 UTC Dec 22 2013 from (172.26.4.2)
Last switchback time:           11:31:11 UTC Dec 22 2013 from (172.26.4.1)
Switchback mode:                Immediate
MGCP Fallback mode:             Enabled/OFF
Last MGCP Fallback start time: 04:54:21 UTC Dec 8 2013
Last MGCP Fallback end time:    11:25:42 UTC Dec 22 2013
MGCP Download Tones:            Disabled
TFTP retry count to shut Ports: 2
FAX mode: disable
Configuration Error History:
store179#show mgcp endpoint
aaln/S0/SU0/0@store179
aaln/S0/SU0/1@store179
aaln/S0/SU0/2@store179
aaln/S0/SU0/3@store179
aaln/S0/SU1/1@store179
PORT            CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
=============== == ============ ===== ==== ======== ======== ==
0/0/0           -- fxs-ls      up    dorm on-hook idle     y
0/0/1           -- fxs-ls      up    dorm on-hook idle     y
0/0/2           -- fxs-ls      up    dorm on-hook idle     y
0/0/3           -- fxs-ls      up    dorm on-hook idle     y
0/1/0           -- fxo-ls      up    down idle     off-hook y
PORT            CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
=============== == ============ ===== ==== ======== ======== ==
0/0/0           -- fxs-ls      up    dorm on-hook idle     y
0/0/1           -- fxs-ls      up    dorm on-hook idle     y
0/0/2           -- fxs-ls      up    dorm on-hook idle     y
0/0/3           -- fxs-ls      up    dorm on-hook idle     y
0/1/0           -- fxo-ls      up    down idle     off-hook y
I have dial-peers for the ports .
Any ideas ?

Debug mgcp packets
*Dec 25 13:13:25.808: MGCP Packet sent to 172.26.4.2:2427--->
NTFY 257951726 *@store179.super-pharm.co.il MGCP 0.1
X: 0
O:
<---
*Dec 25 13:13:25.820: MGCP Packet received from 172.26.4.2:2427--->
200 257951726
<---
conf t
Enter configuration commands, one per line. End with CNTL/Z.
store179(config)#no mgcp
WARNING: no mgcp: Teardown MGCP application may take a while to clean up resources
store179(config)#
*Dec 25 13:13:36.220: MGCP Packet sent to 172.26.4.2:2427--->
RSIP 257951727 *@store179.super-pharm.co.il MGCP 0.1
RM: graceful
RD: 0
<---
*Dec 25 13:13:36.228: %MGCP_APP-6-MGCP_SHUTDOWN_COMPLETE: MGCP Shutdown has completed
mgcp
store179(config)#
*Dec 25 13:13:46.980: MGCP Packet sent to 172.26.4.2:2427--->
RSIP 257951729 *@store179.super-pharm.co.il MGCP 0.1
RM: restart
<---
*Dec 25 13:13:47.004: MGCP Packet received from 172.26.4.2:2427--->
200 257951729
<---
*Dec 25 13:13:47.008: MGCP Packet received from 172.26.4.2:2427--->
RQNT 34773851 AALN/S0/SU0/[email protected] MGCP 0.1
X: 2
R: L/hd
Q: process,loop
<---
*Dec 25 13:13:47.008: MGCP Packet sent to 172.26.4.2:2427--->
200 34773851 OK
<---
*Dec 25 13:13:47.008: MGCP Packet received from 172.26.4.2:2427--->
RQNT 34773852 AALN/S0/SU0/[email protected] MGCP 0.1
X: 2
R: L/hd
Q: process,loop
<---
*Dec 25 13:13:47.012: MGCP Packet sent to 172.26.4.2:2427--->
200 34773852 OK
<---
*Dec 25 13:13:47.012: MGCP Packet received from 172.26.4.2:2427--->
RQNT 34773853 AALN/S0/SU0/[email protected] MGCP 0.1
X: 2
R: L/hd
Q: process,loop
<---
*Dec 25 13:13:47.012: MGCP Packet sent to 172.26.4.2:2427--->
200 34773853 OK
<---
*Dec 25 13:13:47.012: MGCP Packet received from 172.26.4.2:2427--->
RQNT 34773854 AALN/S0/SU1/[email protected] MGCP 0.1
X: 0
R: L/hd
Q: process,loop
<---
*Dec 25 13:13:47.016: MGCP Packet sent to 172.26.4.2:2427--->
200 34773854 OK
<---
*Dec 25 13:13:47.016: MGCP Packet received from 172.26.4.2:2427--->
RQNT 34773855 AALN/S0/SU0/[email protected] MGCP 0.1
X: 2
R: L/hd
Q: process,loop
<---
*Dec 25 13:13:47.016: MGCP Packet sent to 172.26.4.2:2427--->
200 34773855 OK
<---
*Dec 25 13:13:47.020: MGCP Packet sent to 172.26.4.2:2427--->
NTFY 257951731 *@store179.super-pharm.co.il MGCP 0.1
X: 0
O:
<---
*Dec 25 13:13:47.020: MGCP Packet received from 172.26.4.2:2427--->
AUEP 34773856 AALN/S0/SU0/[email protected] MGCP 0.1
F: X, A, I
<---
*Dec 25 13:13:47.024: MGCP Packet sent to 172.26.4.2:2427--->
200 34773856
I:
X: 2
L: p:10-20, a:PCMU;PCMA;G.nX64, b:64, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-220, a:G.729;G.729a;G.729b, b:8, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-110, a:G.726-16;G.728, b:16, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-70, a:G.726-24, b:24, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-50, a:G.726-32, b:32, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-270, a:G.723.1-H;G.723;G.723.1a-H, b:6, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-330, a:G.723.1-L;G.723.1a-L, b:5, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
M: sendonly, recvonly, sendrecv, inactive, loopback, conttest, data, netwloop, netwtest
<---
*Dec 25 13:13:47.024: MGCP Packet received from 172.26.4.2:2427--->
AUEP 34773857 AALN/S0/SU0/[email protected] MGCP 0.1
F: X, A, I
<---
*Dec 25 13:13:47.024: MGCP Packet sent to 172.26.4.2:2427--->
200 34773857
I:
X: 2
L: p:10-20, a:PCMU;PCMA;G.nX64, b:64, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-220, a:G.729;G.729a;G.729b, b:8, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-110, a:G.726-16;G.728, b:16, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-70, a:G.726-24, b:24, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-50, a:G.726-32, b:32, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-270, a:G.723.1-H;G.723;G.723.1a-H, b:6, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-330, a:G.723.1-L;G.723.1a-L, b:5, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
M: sendonly, recvonly, sendrecv, inactive, loopback, conttest, data, netwloop, netwtest
<---
*Dec 25 13:13:47.028: MGCP Packet received from 172.26.4.2:2427--->
AUEP 34773858 AALN/S0/SU0/[email protected] MGCP 0.1
F: X, A, I
<---
*Dec 25 13:13:47.028: MGCP Packet sent to 172.26.4.2:2427--->
200 34773858
I:
X: 2
L: p:10-20, a:PCMU;PCMA;G.nX64, b:64, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-220, a:G.729;G.729a;G.729b, b:8, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-110, a:G.726-16;G.728, b:16, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-70, a:G.726-24, b:24, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-50, a:G.726-32, b:32, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-270, a:G.723.1-H;G.723;G.723.1a-H, b:6, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-330, a:G.723.1-L;G.723.1a-L, b:5, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
M: sendonly, recvonly, sendrecv, inactive, loopback, conttest, data, netwloop, netwtest
<---
*Dec 25 13:13:47.028: MGCP Packet received from 172.26.4.2:2427--->
AUEP 34773859 AALN/S0/SU1/[email protected] MGCP 0.1
F: X, A, I
<---
*Dec 25 13:13:47.032: MGCP Packet sent to 172.26.4.2:2427--->
200 34773859
I:
X: 0
L: p:10-20, a:PCMU;PCMA;G.nX64, b:64, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-220, a:G.729;G.729a;G.729b, b:8, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-110, a:G.726-16;G.728, b:16, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-70, a:G.726-24, b:24, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-50, a:G.726-32, b:32, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-270, a:G.723.1-H;G.723;G.723.1a-H, b:6, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-330, a:G.723.1-L;G.723.1a-L, b:5, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
M: sendonly, recvonly, sendrecv, inactive, loopback, conttest, data, netwloop, netwtest
<---
*Dec 25 13:13:47.032: MGCP Packet received from 172.26.4.2:2427--->
AUEP 34773860 AALN/S0/SU0/[email protected] MGCP 0.1
F: X, A, I
<---
*Dec 25 13:13:47.032: MGCP Packet sent to 172.26.4.2:2427--->
200 34773860
I:
X: 2
L: p:10-20, a:PCMU;PCMA;G.nX64, b:64, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-220, a:G.729;G.729a;G.729b, b:8, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-110, a:G.726-16;G.728, b:16, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-70, a:G.726-24, b:24, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-50, a:G.726-32, b:32, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-270, a:G.723.1-H;G.723;G.723.1a-H, b:6, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-330, a:G.723.1-L;G.723.1a-L, b:5, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
M: sendonly, recvonly, sendrecv, inactive, loopback, conttest, data, netwloop, netwtest
<---
*Dec 25 13:13:47.036: MGCP Packet received from 172.26.4.2:2427--->
200 257951731
<---
*Dec 25 13:13:48.004: MGCP Packet sent to 172.26.4.2:2427--->
RSIP 257951728 *@store179.super-pharm.co.il MGCP 0.1
RM: restart
<---
*Dec 25 13:13:48.036: MGCP Packet received from 172.26.4.2:2427--->
200 257951728
<---
store179(config)#
store179(config)#
store179(config)#
store179(config)#
store179(config)#
store179(config)#
store179(config)#u all
^
% Invalid input detected at '^' marker.
store179(config)#exit
store179#
*Dec 25 13:14:02.016: MGCP Packet sent to 172.26.4.2:2427--->
NTFY 257951732 *@store179.super-pharm.co.il MGCP 0.1
X: 0
O:
<---
*Dec 25 13:14:02.032: MGCP Packet received from 172.26.4.2:2427--->
200 257951732
it's not possiable to do the other debugs they stuck the router

Similar Messages

SPA2102 FXS port state monitoring

Hi all,
Is there any way to get FXS port state for LinkSys SPA2102 VoIP adapter (i.e. is there a phone that connected to it or not) remotely, for example, via SNMP ?
Thanks.

Here's the bug ID: CSCse15025
Doubt the NM is faulty - we had the same issue in a 2821 and migrated to 12.4(4)T4 to correct it. No hardware replacement required. All has worked fine since then.
HTH
Tom

Valcom 2001A single zone paging system with a Cisco 2821 FXS port

I am new at troubleshooting the Valcom paging system with Cisco 2821 router. I recently installed a Valcom 2001A that is connecting to FXS port on the Cisco router. The paging works but the ringing does not stop when the page extension is dialed (you can talk over the ringing). I was told to use the Valcom 9970 to work with the FXS port on my router. Will the V9970 worth with the 2001A or in place of it? Is there anything else I need to know to perfect this install? Thank you!

Put the command 'forward-digits extra ,,,,01' on the outgoing POTS dial-peer. Each comma is one second of delay.

FXS Port stucks in Off-Hook state on NM-HDA

Hi,
i have some trouble with an FXS Port on an NM-HDA which stucks in the Off-Hook state, after some time of normal operation. The Voice-Port is in Off-Hook state regardless of if there is an Enddevice attached or not. Even an reload of the router does not help.
The voice port is configured for loop-start. The NM-HDA is housed in an Cisco 3725 running IOS Vers. 12.3(14)T2 with H.323 signalling.
Is there anybody who has seen this before? Could this be caused by an IOS-Bug or is it more likley that the NM-HDA is faulty?
Regards
Robert

Here's the bug ID: CSCse15025
Doubt the NM is faulty - we had the same issue in a 2821 and migrated to 12.4(4)T4 to correct it. No hardware replacement required. All has worked fine since then.
HTH
Tom

Cisco 2432-24FXS Calls won't ring FXS ports when placed in Huntgroup

Hi,
I am having an issue getting calls to ring through on the FXS ports when using the "trunkgroup" command under the POTS dial-peers. Calls will ring through fine if I use the "port" command under the pots dial-peer. What I am trying to accomplish is getting a single number to hunt through 13 FXS ports in a round-robin fashion. With the below setup I am getting a SIP 404 not found message in the SIP debug info. I am not sure if I am missing something here or what the deal is. If the below information is not enough I would be happy to provide additional info. Any idea's why this configuration doesn't seam to work?
trunk group HuntGroup1
hunt-scheme round-robin both up
dial-peer voice 1 voip
translation-profile outgoing 7to11
destination-pattern .T
progress_ind setup enable 3
no modem passthrough
voice-class codec 1
session protocol sipv2
session target dns:XXXXXXXX
dtmf-relay rtp-nte
fax rate 14400
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
ip qos dscp cs5 media
no vad
dial-peer voice 300 pots
trunkgroup HuntGroup1
description TEST NUMBER
destination-pattern XXXXXXXXXX
voice-port 2/0
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 1
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/1
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 2
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/2
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 3
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/3
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 4
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/4
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 5
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/5
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 6
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/6
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 7
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/7
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 8
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/8
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 9
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/9
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 10
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/10
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 11
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/11
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 12
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/12
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 13
station-id number XXXXXXXXXX
caller-id enable
Message was edited by: Thomas Schmidt
Added CCSIP Debug and Router Config.

Hi.
Can you please attach the complete config and a debug ccsip message?
Thanks
Regards
Carlo
Sent from Cisco Technical Support iPhone App

Cisco FXS Port - RJ11 to RJ45

Hi,
I have a VIC3-2FXS/DID in Switerzland and my customer has asked for it to be connected to a fax machine through Strucuted cabling and they would like to know what type of cables they required.
They want RJ11 (FXS Port) to RJ45 (Patch Panel) then RJ45 (Patch Panel) to RJ11(Fax Machine).
Could someone explain the pins out of the cables, as it is going to be two RJ11 to RJ45 cables do they need to rollover?
Thanks for any help.

All cabling on Cisco voice cards is straight through from the port to the device. RJ11 has 2 pins, for tip and ring. That's blue and white/blue. RJ45 has 8 pins, but if you want to stick with the 568B wiring standard on the RJ45 jacks,you would use this.
Blue: RJ11(pin1)----RJ45(pin 4)--------(pin4)RJ45-----(pin 1)RJ11
White/Blue: RJ11(pin2)----RJ45(pin 5)--------(pin 5)RJ45-----(pin 2)RJ11
If you actually have RJ14 jacks (4 pins), its pins 2 and 3 (the middle pins) which are used. If it is RJ25, it's still the middle pins, which would be 3 and 4.

RADIUS/DECODE: parse unknown cisco vsa "profile-name" - IGNORE

Dear Team,
I have faced an issue with dot1x mab authorization between cisco switch 3750 and ISE 1.1. I have cisco IP phone connected on port # gig1/0/1 to authenticated through MAB with cisco ISE
int gig 1/0/1
switchport mode access
switchport access vlan 9
switchport voice vlan 410
authentication order mab dot1x
authentication priority dot1x mab
spanning-tree portfast
authentication host-mode multi-domain
authentication port-control auto
dot1x pae authenticator
mab
dot1x timeout tx-period 3
dot1x max-reauth-req 2
authentication periodic
authentication timer reauthenticate server
I can get authentication successfuly but can't download the authorization profile on the gig1/0/1 port since I can see that everything seems fine from the ISE side. the phone is authenticated and authorized fine. so, I debug the dot1x & radius flows from the switch side and get this result.
RADIUS/ENCODE(00000043):Orig. component type = Dot1X
RADIUS(00000043): Config NAS IP: 1.1.1.2
RADIUS(00000043): Config NAS IPv6: ::
RADIUS/ENCODE(00000043): acct_session_id: 57
RADIUS(00000043): sending
RADIUS(00000043): Sending a IPv4 Radius Packet
RADIUS(00000043): Send Access-Request to 1.1.1.1:1812 id 1645/72, len 261
RADIUS: authenticator 82 94 D8 85 E9 E0 CF 71 - 03 FE C5 BA 76 EC 76 C4
RADIUS: User-Name           [1]   14 "00152bd20c19"
RADIUS: User-Password       [2]   18 *
RADIUS: Service-Type        [6]   6   Call Check                [10]
RADIUS: Vendor, Cisco       [26] 31
RADIUS:   Cisco AVpair       [1]   25 "service-type=Call Check"
RADIUS: Framed-MTU          [12] 6   1500
RADIUS: Called-Station-Id   [30] 19 "30-F7-0D-CD-5F-01"
RADIUS: Calling-Station-Id [31] 19 "00-15-2B-D2-0C-19"
RADIUS: Message-Authenticato[80] 18
RADIUS:   90 B9 61 65 CC A6 B2 89 BC C8 3D DC D4 14 03 C5               [ ae=]
RADIUS: EAP-Key-Name        [102] 2   *
RADIUS: Vendor, Cisco       [26] 49
RADIUS:   Cisco AVpair       [1]   43 "audit-session-id=C0A8424200000036001B2AAE"
RADIUS: NAS-Port-Type       [61] 6   Ethernet                  [15]
RADIUS: NAS-Port            [5]   6   50101
RADIUS: NAS-Port-Id         [87] 22 "GigabitEthernet1/0/1"
RADIUS: Called-Station-Id   [30] 19 "30-F7-0D-CD-5F-01"
RADIUS: NAS-IP-Address      [4]   6   1.1.1.2
RADIUS(00000043): Started 5 sec timeout
RADIUS: Received from id 1645/72 1.1.1.1:1812, Access-Accept, len 297
RADIUS: authenticator D5 2C 29 3B AC C8 A7 2F - A4 75 45 F5 51 6D 4F A8
RADIUS: User-Name           [1]   19 "00-15-2B-D2-0C-19"
RADIUS: State               [24] 40
RADIUS:   52 65 61 75 74 68 53 65 73 73 69 6F 6E 3A 43 30 [ReauthSession:C0]
RADIUS:   41 38 34 32 34 32 30 30 30 30 30 30 33 36 30 30 [A842420000003600]
RADIUS:   31 42 32 41 41 45            [ 1B2AAE]
RADIUS: Class               [25] 50
RADIUS:   43 41 43 53 3A 43 30 41 38 34 32 34 32 30 30 30 [CACS:C0A84242000]
RADIUS:   30 30 30 33 36 30 30 31 42 32 41 41 45 3A 69 73 [00036001B2AAE:is]
RADIUS:   65 33 2F 31 35 30 33 30 36 35 37 38 2F 33 38 36 [ e3/150306578/386]
RADIUS: Termination-Action [29] 6   1
RADIUS: Message-Authenticato[80] 18
RADIUS:   09 17 84 AB 27 8E B4 E0 F4 A6 93 EE 19 2A A6 34               [ '*4]
RADIUS: Vendor, Cisco       [26] 34
RADIUS:   Cisco AVpair       [1]   28 "device-traffic-class=voice"
RADIUS: Vendor, Cisco       [26] 75
RADIUS:   Cisco AVpair       [1]   69 "ACS:CiscoSecure-Defined-ACL=#ACSACL#-IP-PERMIT_ALL_TRAFFIC-4fe7f797"
RADIUS: Vendor, Cisco       [26] 35
RADIUS:   Cisco AVpair       [1]   29 "profile-name=Cisco-IP-Phone"i
RADIUS(00000043): Received from id 1645/72
RADIUS/DECODE: parse unknown cisco vsa "profile-name" - IGNORE
%MAB-5-SUCCESS: Authentication successful for client (0015.2bd2.0c19) on Interface Gi1/0/1 AuditSessionID C0A8424200000036001B2AAE
%AUTHMGR-7-RESULT: Authentication result 'success' from 'mab' for client (0015.2bd2.0c19) on Interface Gi1/0/1 AuditSessionID C0A8424200000036001B2AAE
%DOT1X_SWITCH-5-ERR_VLAN_RSPAN: Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1. 802.1x is incompatible with RSPAN AuditSessionID C0A8424200000036001B2AAE
RADIUS/ENCODE(00000000):Orig. component type = Invalid
so, I notice two things :-
1-" RADIUS/DECODE: parse unknown cisco vsa "profile-name" - IGNORE " on the radius attribute since I beleive that I configure the radius vsa attribute fine as shows
aaa new-model
aaa authentication dot1x default group radius
aaa authorization network default group radius
aaa accounting dot1x default start-stop group radius
aaa accounting system default start-stop group radius
aaa session-id common
aaa accounting update periodic 5
aaa server radius dynamic-author
client 1.1.1.1 server-key 0 cisco
radius-server attribute 8 include-in-access-req
radius-server attribute 25 access-request include
radius-server dead-criteria time 5 tries 3
radius-server host 1.1.1.1 auth-port 1812 acct-port 1813 key cisco
radius-server vsa send accounting
radius-server vsa send authentication
2- "%DOT1X_SWITCH-5-ERR_VLAN_RSPAN:" since I didn't have any configuration related to RSPAN.
so, anybody have any idea to fix this issue.
Regards
Basel

It is not the ACL it is ignoring, it's the profile-name, which it should, because it has nothing to use that for. However, you should look into VLAN 410, to check and see if you have any config relating to that vlan, the only actual error i see in your logs is the one regarding assigning vlan 410. Could you please post you entire switch config, see we can see what else you might have configured.
%DOT1X_SWITCH-5-ERR_VLAN_RSPAN: Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1. 802.1x is incompatible with RSPAN AuditSessionID C0A8424200000036001B2AAE - See more at: https://supportforums.cisco.com/message/3863298#3863298
%DOT1X_SWITCH-5-ERR_VLAN_RSPAN: Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1. 802.1x is incompatible with RSPAN AuditSessionID C0A8424200000036001B2AAE - See more at: https://supportforums.cisco.com/message/3863298#3863298
%DOT1X_SWITCH-5-ERR_VLAN_RSPAN: Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1. 802.1x is incompatible with RSPAN AuditSessionID C0A8424200000036001B2AAE - See more at: https://supportforums.cisco.com/message/3863298#3863298
%DOT1X_SWITCH-5-ERR_VLAN_RSPAN: Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1. 802.1x is incompatible with RSPAN AuditSessionID C0A8424200000036001B2AAE - See more at: https://supportforums.cisco.com/message/3863298#3863298
%DOT1X_SWITCH-5-ERR_VLAN_RSPAN: Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1. 802.1x is incompatible with RSPAN AuditSessionID C0A8424200000036001B2AAE - See more at: https://supportforums.cisco.com/message/3863298#3863298
%DOT1X_SWITCH-5-ERR_VLAN_RSPAN: Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1. 802.1x is incompatible with RSPAN AuditSessionID C0A8424200000036001B2AAE - See more at: https://supportforums.cisco.com/message/3863298#3863298
%DOT1X_SWITCH-5-ERR_VLAN_RSPAN: Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1. 802.1x is incompatible with RSPAN AuditSessionID C0A8424200000036001B2AAE - See more at: https://supportforums.cisco.com/message/3863298#3863298
%DOT1X_SWITCH-5-ERR_VLAN_RSPAN: Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1. 802.1x is incompatible with RSPAN AuditSessionID C0A8424200000036001B2AAE - See more at: https://supportforums.cisco.com/message/3863298#3863298
%DOT1X_SWITCH-5-ERR_VLAN_RSPAN: Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1. 802.1x is incompatible with RSPAN AuditSessionID C0A8424200000036001B2AAE - See more at: https://supportforums.cisco.com/message/3863298#3863298

GWMonitor lists GWIA as state Unknown

We've been having issues with GroupWise ever since we upgraded to Linux. Today's issue is the GWIA web interface. Whenever I try to connect to our gwia web interface directly on port 9850 it redirects me to GWMonitor.
And under GWMon it lists all of the GroupWise components as running normally except the GWIA.
The GWIA state is unknown. I've tried changing the port, restarting groupwise, restarting the server, changing the HTTP username and password in C1,
Normal 0 d 1 h 6 m crofton MTA 0 d 1 h 10 m 0 0 Linux 8.0.2 (12/11/2010)
Unknown 0 d 1 h 11 m GWIA.crofton GWIA 0 d 0 h 0 m N/A N/A ?
Normal 0 d 1 h 6 m po.crofton POA 0 d 1 h 10 m N/A N/A Linux 8.0.2 (12/11/2010)
Normal 0 d 1 h 6 m webacc.crofton WEBACC 0 d 1 h 10 m N/A N/A Linux 8.0.2 (12/11/2010)
Name GWIA.crofton
Type GWIA
Address SERVER-IP:9850
Poll Type XML
State Unknown
It was set to SNMP but I brought down GWMon and then Restarted the GWIA and then brought GWMon back up and it set to XML. But the same error either way.
I also made sure that the port 9850 was not in use by something else while both were down.
Tyler

Well, when we switched to Linux, our GroupWise issues pretty much went away. Exact opposite of what you site. I guess YMMV.
This would not be on the other side of a Firewall by chance? Check that. You should also be able to telnet to the port if it is running and you have connectivity.
--El
Originally Posted by croftonhouse
Of course right after posting this thread it switched to not listening. :-/

CFwd on FXS-Ports (mgcp)

hi!
How can I forward the Calls on an Phone witch is connected to an FXS-Port (mgcp, vg200)?
How can I use the other Features, like PickUp etc.
vy Markus

Since there has been no response to your post, it appears to be either too complex or too rare an issue for other forum members to assist you. If you don't get a suitable response to your post, you may wish to review our resources at the online Technical Assistance Center (http://www.cisco.com/tac) or speak with a TAC engineer. You can open a TAC case online at http://www.cisco.com/tac/caseopen
If anyone else in the forum has some advice, please reply to this thread.
Thank you for posting.

FXS Ports & Pickup Groups

Is there a way to make an analog phone connected to an FXS port a part of a call pickup group that contains both analog phones & IP phones? I setup a lab and used MGCP to add the gateway and I was able to add the DN associated with the FXS port to a call pickup group. However, I am unable to figure out how to answer the call from the analog phone when another IP phone in the call pickup group is ringing.
Thanks in advance

Hi
You are going down the right track with this.
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Unified%20Communications%20and%20Video&topic=IP%20Telephony&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1dde5372/0#selected_message
See this other post I made (for a different purpose, but the principal is the same - it just opens up features available to IP phones for FXS ports by registering them using SCCP).
Regards
Aaron
Please rate helpful posts...

MGCP FXS ports requires a license in CUCM9

Hello!
I am connecting Some analoge phones to VG350 FXS ports which is configured as a MGCP Gateway in CUCM. I beleive MGCP did not requires any license for it. Can some confirm this ? is there any Cisco doc on it ?
Thanks & Regards,

Hi Sambit,
Technically u are correct but legally I think u would be requiring license.
even the ordering guide says Analog devices are supported with Essential USer license and must be purchased through UCL.
http://www.cisco.com/web/partners/downloads/partner/WWChannels/technology/ipc/downloads/finalcopy.pdf
regds,
aman

FXS Port Query?

Hi,
We are running VoIPovFR to a remote location, which has 2 x 4FXS/DID module installed into a C2621XM chassis. We are using IOS c2600-is-mz.122-15.
Out of the 8 ports, two continually go off-hook, FXSLS_WAIT_OFFHOOK before finally going into a FXSLS_PARK state. I have moved the cabling and the error occurs on which ever port the two lines plugs into.
Has anyone ever see this before. To my mind it looks like a cabling issue?
Any ideas?
Thanks

Try wiring all FXS ports like this
FXS PORT 0 RJ11 3-----------------------A ANALOGUE
FXS PORT 0 RJ11 4-----------------------B PHONE
FXS PORT 1 RJ11 3-----------------------A ANALOGUE
FXS PORT 1 RJ11 4-----------------------B PHONE
FXS PORT 2 RJ11 3-----------------------A ANALOGUE
FXS PORT 2 RJ11 4-----------------------B PHONE
FXS PORT 3 RJ11 3-----------------------A ANALOGUE
FXS PORT 3 RJ11 4-----------------------B PHONE
Ensure that all other wires are left disconnected

EFTPOS No Response X0 Using FXS Port

Hi All,
Trying to get an EFTPOS machine working connected into an FXS Port using SCCP/STCAPP Protocol for call control.
The port is registered in CUCM, I can connect an analogue phone to the port and successfully call the Bank's 1800 Number etc, I can make other external calls no problem.
When I try the EFTPOS Machine, the call setup runs through normally and I see the call is then in a connected state. Approx about 10 or seconds later the call is cleared by the local device with an 0x8090 code Normal Clearing. The call is then disconnected and released as per any other call.
The EFTPOS Machine prints a error for "Declined No Response X0"
I have attached the following debugs.
debug isdn q931
debug voip vtsp all
debug vop ccapi inout
debug voip rtp session named-event
Calling Number is 0245604627
Called Number is 1800509183
General environment setup is as follows.
EFTPOS connect to FXS Port -> Registered to CUCM (9.1.2) -> SIP Trunk -> IOS 15.x -> ISDN Pri.
Any feedback i smuch appreciated.
Ben

Not so sure if the service code being utilize by the FXS is the same as what is mentioned in VSA.Then again, the manual says "dial the corresponding * code on the client station" and if you look at an SPA9xx phone, it has the following codes defined for call park and call unpark code.
*38
*39

2960x - stack cables connected while switches power on. SFP ports - status unknown

Connected 2960x uplink using SFP ports both stacks and all 4 ports worked good.
Remote tech connected last stack cable between first and last switch, in 2 different 2960x stacks of switches, while switches were powered on. A longer stack cable was needed. 3 of 4 SFP ports did stopped communicating.
One stack SFP stayed up in switch 2, not master. Completed reload - other SPF connected in switch 4/0/52
Second stack no connection on either SFP, remote tech power cycled switches.
After power cycle one SFP worked in Master 1/0/52, other switches SFP ports show "unknown" when inserting SFP.
Configured port 48 on stack with issue and connected second uplink just fine.
Has anyone experienced this with the SFP's?
- GLC-T P/N 30-1410-03
Looking for documentation on reccommending procedure for connecting stack cables while switches should be powered off or not.
Thanks,

Opened Cisco TAC case. the following bug was found.
the two different HBRN's below require 2 different IOS and they cannot be in same stack.
https://tools.cisco.com/bugsearch/bug/CSCur56395
switch#sh ver | s Hardware Board
Hardware Board Revision Number : 0x05
switch#remote command 2 sh ver | s Hardware Board
Switch : 2 :------------ Hardware Board Revision Number : 0x05
switch#remote command 3 sh ver | s Hardware Board
Switch : 3 : ------------ Hardware Board Revision Number : 0x12
switch#remote command 4 sh ver | s Hardware Board
Switch : 4 :------------Hardware Board Revision Number : 0x12
From Cisco.
Developers have recommended to upgrade the IOS version of switches with a Hardware Board revision Number below 0x10 to the release 15.0(2.0).EX5ES. this is the one attached to this email and should be applied to switch 1 and 2.
For switches with a Hardware Board revision Number above 0x10 to the release 152-2.4.E1ES, which I will send you right away. This should be done on switch 3 and 4.
Now, If you load the engineering special, you will need to do a full power-cycle (physically unplug the power and plug it back in for every single switch). A simple ‘reload’ will not resolve this.
The same must be done on Switch-0. For this stack you will only need to load the image attached to this email since all the Hardware Board revision Numbers are lower than 0x10.
done.

How to configure FXO and FXS port?

hi,
can anyone help me on how to configure FXO port on 2820 router and FXS port on 2810.
What are the things i need to configure to make a voip network that connect to PSTN network and PBX?

hi
do refer this link which can provide you fair idea to get started with your configs.
http://www.cisco.com/en/US/partner/tech/tk1077/tech_configuration_examples_list.html
regds

Fxs ports state unknown cisco 1861

Similar Messages

Maybe you are looking for