"ghost" audio panel issues

hi,
have a g77a-g41 with a 2600k and 16 gigs ddr3. simple setup with a 180 gb 330 series boot drive and two 2tb seagates secondary drives. onboard auio. just fried my 650 watt ultra p/s and just briefly hooked up a 750watt hybrid p/s to make sure i was correct about p/s outage as i have a h60 cooler to slap in subsequently so i just had the 330 ssd plugged in and nothing else except the hdmi cable. when reveling in my satisfaction i was correct i unfortunately got repeated idiot messages about i believe front panel audio (maybe back) "you plugged in something , was it this or that?". thats cool when i actually plug something in but negative in this case. i usually use both back panels for two 2.1 systems and front is vacant. i know i mistakenly tugged(but not hard) on front panel header wires when unplugging mess of power supply wires but didn't continue when noticed the slightest bit of resistance. anyways, anyone had similar issues? if this occurs subsequent to triple checking everything i'll probably disable onboard and score an aftermarket sound card but i am satisfied(or was) with what i had and dont like tossing away coin so any help would be appreciated.
kind regards
larry

thanks for the quick reply. the one usb port off the front panel works/ same grouping of headers but i really was just verifying that my power supply was the issue. i am rebuilding my dads machine today or swapping a drive i just ghosted due to "immanent hardware failure message" or something like that on his branded pc today. i know my machine auto selected the hdmi for output but didn't even have p/s screwed in and only had 24 pin, 8pin power and one sata power connector hooked up from power supply and i Need to 2x check everything out. kept saying something was plugged in, then out, etc. probably 3 times in the 2 or 3 minutes it was running. going to get the water cooler in there by week end and will let you know what happens.
thanks again for quick reply

Similar Messages

Ghost Audio from Other Clips

Hi All,
I'm having an issue when adding new selections to the project.
1) I add one selection from a clip and the audio is fine;
2) I add another selection from somewhere later in the same clip and I can hear ghost audio from the previous selection;
3) If the second selection in the project is shorter than the first, the ghost audio seems "wrapped" - that is the ghost audio plays from two different points in the previous selection at the same time.
The original clip is a .mov using the Apple Intermediate Codec and AAC audio.
Any advice would be great!
Thanks!
- Charles

Hello All,
I'm updating this in case anyone else has the same issue.
It turns out the AAC encoding was causing the issue. I used QuickTime Pro to save the file with a different audio encoding and all is well, now.
Thanks!
- Charles

Audio Sync issues Premiere CC and AJA T-AP

I need to get the audio sync issues resolved in Premiere. Using CC with an AJA T-tap. I downloaded and installed latest firmware and drivers, and plug-ins. Audio is playing back through Mac Pro line output. When the T-tap is turned off the audio plays in sync with the video on the computer screen. When I turn on T-tap and give it a 200 ms offset, it plays back in sync with my external monitor, but the computer screen is out of sync. If I skip around in the sequence quickly and press the playback, sometimes the monitor is out of sync. I need my audio and video to be in sync on all screens all the time. How do I resolve this issue?
Thanks, Scott

Hi team!
cc: petergaraway
Wondering if anyone has any updates on the Premiere CC v AJA T-Tap situation?
I just bought an AJA to go with our new trash can iMac, which has been beasted out so it shouldn't have any performance issues. I have two thunderbolt displays for the edit and a Samsung LED TV on the wall for client monitoring. There is a 10m HDMI cable running to get to the TV, through walls and ceiling, which I just replaced to a cable with a booster in the middle because I thought that distance might be the first cause of the lag.
I guesstimate we are anywhere between 6-12 frames out at times. Also, the vision seems to be buffering, and thus at times jolts on the screen as it tries to catch up (or back) to the audio.
Audio is coming out through the Headphones jack on the mac to a small Behringer mixer, where I have monitor speakers for the edit and then wall speakers for the client. So I have been keeping the Audio output to the Adobe Desktop Audio. If I select AJA T-Tap it sends the audio straight to the TV, even despite going back into the system settings.
In Preferences > Playback, the AJA settings are to Match Sequence and Minimum Buffer. Playing with the m/s frame offsets doesn't seem to make any progress on the issue. And infact if I push it to 500m/s it only worsens the buffering problem I described above.
I went into the AJA control panel and have made sure everything is set to 1080p25 as our timelines will invariably always be 25fps (Australia).
But right now I am pretty stuck, and think our slight sync issue was better before I introduced the AJA T-Tap to our system, when we ran the HDMI straight out of the back of the Mac. Only problem now is I put the HDMI back there and I don't get a signal to the tv!
Would love any other thoughts or suggestions here.
Mike.

Beats Audio Sound Issue

Hi, well, like many others, im having issues with the beats audio on my LK237AV, im telling you the full history: Clean install of windows 10, after that, installed the drivers via windows update, ok at this point, lik always when i installed linux on my laptop i test the sound quality because the drivers and then, i found that the speakers near the screen works, but the one near me does not, so, i download 3 diferents packages from hp support and nothing, one of then wont install at all (not the rigth driver for me) another one installed an when i was thinking its over again, the sound its really bad, it sound like a portable FM/AM device, then, i tried with the original package for my laptop, and installed the beats audio panel, wich does not install on the other ones, but the sound was missing!. installed again the one wich work for me, and againg i have sound but **bleep** to bad, with hope, i tried with my sennheiser studio earphones and, on the first jack does not sound at all, it continues giving me sound with the speakers that works, the second jack it worked but again i think im going to throw up whe i hear that disgusting sound quality... so here is the think, im asking for all of us the hp guys who has a hp laptop with beats audio to release a driver that works with windows 10, do not attach us with "its not supported" because its your responsability as a pc/laptop maker to release a driver that solve the problem that million of people has after upgrade the SO. thanks in advance,

Thanks for getting back to me with that information!
I've got a couple of things for you to try.
First, try updating to the latest BIOS version F.1C. Download and install F.1C. Your computer will restart on its own during the installation. Allow it to restart and test it for sound issues. If you are still having the problem, move on to the second option.
2nd Option You have the latest audio driver version 6.10.6381.0 installed. There are two versions listed on your driver page which means some units may work better with one version or the other. Don't make any changes to the BIOS version you just installed, but roll back to the earlier audio driver version.
To do this:
Open Device Manager
Expand Sound, video and game controllers
Double-click on IDT HD Audio
Click the Driver tab
If the 'Rollback' button is enabled, click that and restart the computer.
If the 'Rollback' button is not enabled, click Uninstall, do not restart the computer
Download and install 6.10.6345.0 offered on this link and restart
Let me know the results when you get a chance

Audio synch issues in QT

My project displays fine in PE8. No audio synch issues in the preview. After outputting the project to a quicktime movie withe LAN setting the audio becomes seems to run faster than the video, becoming more and more out of synch as the movie plays. Any ideas what might cause such an issue?

The Stream info in MPEG streamclip for files from both cameras gives me this info:
Bitrate: 30.31 Mpbs
Video Tracks:
DV/DVCPRO - NTSC, 720x480, 16:9, 29.9699999999999 fps, 28.77 Mbps
Audio Tracks:
16-Bit Little Endian mono, 48 khz, 768 kbps
I don't know if this helps.

SEO Metadata options not display in admin panel issue.

SEO Metadata options not display in admin panel issue.

Hi there,
Not much information or detail there.
If the New meta option on pages is what you are refering to then the site in question is likely not been upgraded to that beta feature. Only partners who have access to beta options under settings can access that to upgrade.

10.4.10 Audio Popping Issues: Information Check with Internal Speakers

For people with internal speakers, or those without subwoofers: Please read all the way to the bottom to find a test that will determine whether you are also having audio problems, even if you can't hear pops.
We've had a lot of discussion about audio popping due to 10.4.10, and the evidence indicates that the audio circuitry is going to sleep to conserve power, even on AC-only computers like the iMac, Mac Mini, and (at least one) Mac Pro. Some people claim to not have this problem, but I'm wondering if they just aren't noticing it.
Having external speakers with a subwoofer, set to high amplification, are key to obvious detection of the problem. Let the sound subsystem go idle for 30+ seconds (wait a minute with no audio, just to be safe), turn up your external speakers really loud, and cause the computer to make a sound. You should hear a burst before the sound plays. If you repeat the sound, you won't hear the burst. This is the sound of the audio circuitry powering on, and the speakers are amplifying it.
About 30 seconds after the sound finishes playing, if you leave the volume of your speakers turned way up, you should hear a "pop" as the circuitry is powered off. Then, playing another sound will recreate the burst.
I haven't been able to hear these sounds with internal speakers, either on the Mini or iMac. But the problem still exists, and it is detectable... if you know what you are looking for.
The burst of the audio circuitry turning on also causes a delay in the audio. The delay is a noticeable fraction of a second, an it can easily be detected if you have a repeatable source of sound. I like Terminal.app, because I use that application all day, every day. Here is how you can check to see if you are also subject to the audio problems:
1. Start Terminal.app (in the /Applications/Utilities directory).
2. Wait one minute for the audio circuitry to shut down.
3. Without typing anything else, very quickly strike and release the Backspace key.
4. If you pressed the key all the way, the program should have caused a beep. However, if the audio circuitry goes to sleep, the beep should occur after you have moved your hand off the key. This is because the circuitry takes time to power itself on before playing the sound.
5. Now, quickly strike the Backspace key again. You should notice that the sound is produced immediately as you hit the key, without the delay you just witnessed.
6. Strike the Backspace key repeatedly, to confirm that there is no audio delay. Do this about once every second or two. If you press the key too rapidly, not all of the presses will produce sounds... this behavior is not related to the issue we are testing.
7. Wait another minute for the audio circuitry to shut down, and strike the Backspace key once more. You should again observe a delay between your strike and the sound production.
If you witness delays like this, your audio circuitry is also going to sleep, and you are having the same audio problems as the rest of us. However, either because you are using internal speakers, or because your external speakers don't have the appropriate response, you aren't hearing the same bursts and pops as the rest of us.
Please try this test, and report here. I want to build a list of people who previously couldn't hear the sounds, but still have the delay. This might give us a better picture of the scope of the problem.

Re: 10.4.10 Audio Popping Issues: Information Check with Internal Speakers
Your analysis of what is happening is right on.
The problem on my Intel Mac mini with external Klipsch speakers (two mid-range/high and a subwoofer) is REAL obvious as the system emits a hum like a Spinal Tap amplifier turned up to #11 when 10.4.10 powers down the audio circuitry
Then, if I play a song in iTunes, it first pops and the hum disappears right before playing.
Quite annoying.
Here's what I sent to Apple tech support:
Guys/Gals (OS X Engineers):
Concerning the Snap, Crackle Pop Audio problem in the 10.4.10 update:
Please. Just do the right thing and fix the audio.
There is no need to power cycle the audio subsystem to save .0005 amps on your laptops.
And then to make your Mac mini/iMac/other desktop users have to put up with it when using AC power is ridiculous.
Put the audio subsystem back like it was in 10.4.9 and let the laptop battery freaks looking for mini-amp savings get a "work-a-round".
Crikey!
Mac Mini 1.83 Ghz Intel Core Duo 1GB RAM Mac OS X (10.4.9) 20 Years of Microsoft-Induced Grey Hair

Playback pauses and audio sync issues with live video stream

I'm seeing playback pauses about every three seconds and audio sync issues with our live demo stream when using the OSMF/Strobe player. It happens on both our 2Mbps 720p stream and our 480p 750Kbps stream so it does not seem to be related to higher resolution/bandwidth streams. It also happens if I point directly to a stream asset or if I point to a .f4v with both streams listed for dynamic so it does not seem to be related to dynamic streaming specifically.
The same live streams play back very well without pauses or audio sync issues in the Akamai's dynamic player and even slightly better with JW 5.2.
I have viewed the OSMF/Strobe playback on three different laptops of various age (3 months to 2 years) and two are Windows and one is Linux. I have also tried the various buffering options on the Flash Media Player Setup and Strobe setup and it has not made a noticeable difference.
To see the stream with the Akamai player, go to: http://live.kulabyte.com
To see the stream with the OSMF/Strobe player, go to: http://live.kulabyte.com/osmf
I do not have JW set up for public viewing yet, but the two above show the distinct difference.
We are really hoping to start pointing our customers towards the OSMF player because of the support provided by the community and Adobe, but we have to get the quality of the playback to be acceptable first.
If someone has ideas on debugging I can PM the actual video assets to you.
Thanks,
Tim

Hi Tim,
You need to add this setting:
dynamicStreamBufferTime=8
The actual value can be higher or lower. The best practice is to use a value that is twice the keyframe distance. Anyway, try different values and see which performs the best for your content.
I know that the setup page does not contain this option and it is not documented in the UserGuide. We simply missed it. Sorry.
Also note that the dynamic buffering algorithms are not being used for dynamic streaming content. I tried to explain this here:
https://sourceforge.net/adobe/smp/wiki/Dynamic%20Buffering/
Looking forward to your confirmation that this solved your issue.
-Andrian

Beats audio Panel Missing after upgrading to Windows 8.1 and installing HP Reccomended Drivers

I recently upgraded to Windows 8.1 on my HP Envy H8-1450. The Beats audio Panel Disappeared and only shows IDT.
I uninstalled and re-installed the HP reccomended audio drivers several times....no luck.The sound does not sound as it did under Windows 8...actually it is crapy.
Please help.....Thanks.

lacadan,
Did you reboot your PC after installing the IDT codec in Device Manager?
I have upgraded from Win 8 to Win 8.1, have the same driver (6.10.6491.0) as you, and also have a fully functioning Beats Audio Control Panel in Control Panel.
When initially removing the incorrect Beats audio codec in Device Manager you should also check completely remove the drivers from your system, reboot, and Win 8.1 should install the correct version of Beats. You then have to reboot your PC again to complete the installation of Beats.
Jaco
****I am not an HP employee****
Please give a" Kudos" if advice received is relevant or" Accept as Solution" if your problem has been solved.
+++++++++++++++++++++++++++++++++++++++++++++++++++++
H8 1380t CTO, Intel i7 3820
16 GB DDR3
Pegatron Motherboard- IPIWB-PB (Pittsburgh), Radeon HD 7570 1GB. Win 7 Home Premium upgraded to Windows 8.1 Pro.
Envy Phoenix 810-150se, Intel i7 4820k
16 GB DDR3
Pittsburgh2 Mainboard, NVIDIA GTX 645- 2GB GDDR5. Win 8.1 Pro.
HP 560z CTO AMD Phenom II X6 1090T
16 GB DDR3.
Radeon HD 6570
Win 7 Home Premium upgraded to Win 7 Pro.
HP ENVY 17t-j000 CTO Quad Edition Notebook. I7 4702mq
12 GB DDR3
Nvidia Graphics
Win 8 Pro
Errare humanum est.

[SOLVED] Front audio panel still not working on K9N Neo V3

I already posted on this here: https://forum-en.msi.com/index.php?topic=113813.0.
I still didn't get front audio panel to work on MSI K9N Neo V3.
Even with my new case; Sharkoon Revenge, it is not working. It wasn't working on my previous noname case too. However, front audio panel on my previous case was working on several other MBs except on this MSI K9N.
Now, I'm using the latest Realtek HD audio driver. I think it's from February '08. Just as with the driver dowloaded by Vista via Windows Update, anything plugged in front audio panel isn't recognized. In this new version of Realtek driver I can't find this Disable front audio panel option so I can't tell if it is checked or not.
Once more, there is not much to do wrong while connecting. Case front audio panel cabel is the same as on all other cases I've ever seen/had. It's a cable with the same number and position of pins as in all other cases. It fits fine on MSI K9N Neo V3. Rear audio panel is working fine.
Any solution to this!?

Quote from: Jack the Newbie on 07-April-08, 03:25:15
From what I can see from the Sharkoon product page, the front panel connectors of your case are not compliant with the Intel HD Audio Pin Standard.
Do you have a manual for your case that includes Pin/wire definitions for the front audio connectors?
No. There was no manual in package. I never thought I will need one either.
Here is Sharkoon Rebel Pin Assigment; http://img176.imageshack.us/img176/9729/pinslk2.jpg
Quote from: Jack the Newbie on 07-April-08, 03:25:15
Have you tried disabling automatic front panel jack detection in the Realtek HD Audio configuration utility? If you don't know were to find that option, access the tab labeled "Audio I/O" and click on the tool icon.
Yes, I tried disabling it. Two tabs (front audio out and front mic) appeared but none of it works.
Quote from: HenryW on 07-April-08, 03:35:46
From something I read: You can also physically check the audio cable of the front panel audio solution. If there is a cable connected to Pin 4, you have an HD Audio module; if there is no cable to Pin 4, you have an AC97 module.
I don't really understand this. Could you please check this on Pin Assignment scan I uploaded above!?

Flv audio sync issues & player 9

Greetings, I've been looking for a solution for weeks, and
thought I'd give the forums a shot.
I have a client site with 6 progressively downloaded flv
clips that play when a button is clicked.
The flv files are encoded with After Effects 6.5, and the swf
files are published in Player 8.
The video clips are made with an alpha channel of a guy
talking and are about 30 sec to 1 minute long each.
The problem is audio sync issues on certain computers during
playback even when the files are completely buffered.
The other problem is that these flv files won't play on
computers that have player 9 loaded.
I'm investigating whether there are audio sync issues when
encoding flv files from AE 6.5, but still really
confused about the player 9 issue. I was wondering if there
are updates to 9 I can recommend to my client
or if adobe knows of any bugs that are currently being looked
into.
Thanks,
Kevin

I may just be talking to myself here, but...
Could there be any difference in the way an flv plays when
you
import the flv to the stage, as opposed to playing it
dynamically
using the NetStream class? Could this cause any audio sync
issues? Does Flash Player 9 have any difficulties displaying
flv files loaded dynamically?
Any ideas from Adobe folks would be great. Thanks.

Quicktime audio sync issues

Hello,
I have quicktime version 10 (128). I can't get anything to play in it without there being severe audio sync issues every time. I can't figure out why. Can someone please help me fix this problem?
When I export my movies from imovie to quicktime it will play in quicktime, properly and without sync issues, for a really short period of time - seconds. But after that, the audio no longer matches the video. I know it's an issue in QT because when I upload the video to YouTube there are no audio sync issues whatsoever.
Help?
Thank you so much,
YahYah

I am dissapointed to see that no one has addressed this issue. I have similar issues.
The MP4's play perfectly in the quicktime player but in Premiere they are off by varying degrees sometimes up to a minute even. I had similar problems in the past with files from the same producer. However last time I was able to change the extension before importing and then sync them up manually on the timeline. It worked everytime. This time however when I change the extension Premiere brings it in as an audio only file.

MP4 Video from Flip Ultra having Audio Sync Issues

All of sudden I've started having audio sync issues with the mp4 footage exported from the The Flip Ultra camera. Ive tryed the mp4 footage in both windows 7 and Mac OS X and i'm having the same audio issue but when I watch in the flip software or in iMovie no issues. Any know why this has just started happening?

Work through all of the steps (ideas) listed at http://ppro.wikia.com/wiki/Troubleshooting
If your problem isn't fixed after you follow all of the steps, report back with ALL OF THE DETAILS asked for in the FINALLY section, the questions at the end of the troubleshooting link... most especially the codec used... see Question 1

Audio Sync Issue on Export

Hello,
I have an issue with an export that I am attempting to do. I have used 50 still photos (psd) and created a slide show in after effects. It is working well. I attempted to create 4 comps made from standard dv footage. 720 x 480 from video cameras in the 1990s. I need to export out eventually to 1920 x 1080 for showing on our TV channel. It would be a .m2t format. When i attempted to do a test export, everything worked fine....the photo comps were good, the only problems were the video clips that had video/audio sync issues.
I am not sure what the problem is exactly. I feel my workflow is not right and that is leading to this issue.
I created the 50 slide comps in AE
I then used the hour long DV clips in PrPRO to make sub clips (about 30 seconds each, total of 8)
I rendered these out to then import into AE
imported into AE and made comps out of them
then render out a test file that would be my finalproject in mpeg format.
I would like to not render the video a second time and would like, basically to take my AE photo comps straight to prmiere pro to insert the DV footage but don't know how exactly to do that.
Is there something that you can recommend.
Thanks,
M

We need to know a lot more to help you. Please provide answers to the questions listed here: "FAQ: What information should I provide when asking a question on this forum?"

Trouble exporting 11-min film as XML because of audio translation issue

Hi, I am trying to export a short film XML file of approximately 11 minutes for a sound engineer and it's coming up with a ton of audio translation issues.
Can I attach the report and someone help me? Most of the issues are audio tracks from ADR but I recorded them with the same H4Zoom I used for the original, and some were the original production audio to which I applied the DeNoiser effect. They're all stereo files with the exception of a few mp3s which were special effect sounds. Why are they not being translated? What can I do to get this into an .xml?? It looks like somewhere between 100-150 audio files were not translated.

are you using merged clips? premiere merged clip XML issue
if the sound engineer will take another format, premiere can export OMF or if you have audition you can open the OMF in audition and export it as a fcp xml.

"ghost" audio panel issues

Similar Messages

Maybe you are looking for