GNB Max and firewire

When I plug a firewire device into the GNB Max, nothing happens. The firwire controller shows up in the device manager and doesn't have any conflicts, also I double checked to make sure that firewire is enabled in the bios. I followed the instructions for connecting the firewire bracket to the mainboard.

It is a Digital VHS Recorder. With my old mobo, I had a pci firewire card, and all I had to do was plug it in, then I could choose the drivers.

Similar Messages

RESOLUTION: GNB MAX and Radeon 9700 Crashes

I had various lock-ups, crashes and "Windows detected and recovered from a device failure" error messages with my GNB MAX motherboard and Radeon 9700 and they are now fixed.
I was able to receive a beta version of an upcoming set of drivers from ATI and they did the trick!!
Just wanted to give you all some hope.
Hang in there!

Oops, I spoke too soon. I think FastWrites is on (I remember turning it off before on previous drivers and noticing a big slow down that is not present now) but there isn't a SmartGart tab appearing in my ATI control panel any more. I checked Advanced - Options - Details and yes, 8X is on.
How can I verify that FastWrites is on without the SmartGart tab?

MSI GNB MAX and RICOH R5C476II PCI to Cardbus bridge not working! Help

Why my PCMCIA & CARDBUS Card Reader based on RICOH R5C476II Chipset not
working on MSI GNB MAX BOARD (with newer bios 2.3)???
My Card reader is fine and working properly on many ithers motherboards like: ABIT BD7-II based
on Intel 845E Chipset, or ASUS TUSIM, ASUS TUSL, and ASUS PIIIB-F
Why ??
Please help me.

Yes, sure. I'm trying to use all of five PCI slots, and after slot chnge I,m setting Reset Configuration data in BIOS.
result is the same in all Card positions. Card is detected, but not working corectly.
I'm trying to resolve any hardware conflicts by disabling all od internal mothebrord components like IEE1394 Audio, Serial Ata and others - no cahnges, no solutions ....

MSI GNB Max and P4 3.06 with 56C Idle (Bios)

is that ok or to high, i know about some bugs with the Temp Sensor so there are my 2 cents ! :D
Please give me some feedback thx. !

I had the exact same problem. I bought a Cooler Master IHC-H71 CPU cooler and it brought me down to 40-44 at idle. Ordered it from http://www.phamcomputer.com

MSI GNB Max (MS-6565): insufficient voltage

I have just installed my new GNB Max, and got XP Pro up and running. Upon installing PC Alert 4, I recieved a warning that the +3.3V was actually sub 3V(2.9+V). What effect will this have? And what kind of Variance should I tolerate?
Many thanks.

My GNB Max + Antec true power 430 read 3.33.
Sounds like a power supply not handling the load.
Acceptable tolerance in the PC industry is +-5% (3.135 is therfor the lower limit)

Difference between gnb max 1 and 2??

Hi i just looked at the products page, but I cant see the difference between the gnb max 1 and 2.
can some help please?
thx in advance !

GNB Max------1.0------- 2.0
LAN-----------1Gbit----100Mbit
RAID----------S.ATA----none
FireWire-----3port----none
AGP----------Pro x8----x8

Games and GNB Max

Oh Joy, more problems. None of the games that the kid had will run on this machine. I've been to the ATI website and they show no issues with any of the games other than Battlefield 1942. However on EAs forums, apparantly they are having problems with one of the expansions. I'm sure that if the problems turn out to be MSI related, I'll get no help.

I had the same problem Radeon 9700 pro / GMB Max mobo. this is what I did,
uninstalled all video drivers from the computer. /reboot
put 256 in the agp apeture size
installed the latest drivers from ATI , I think its Cat 3.2 plus the control panel drivers. /reboot
then I disabled fast write in the smartgart control panel
all is well since then, I play lots of games online and off
and I havent had any problems. its been 3 weeks now since I build this system and all is good. I also ran the bench mark, did see a diffrence with the fast write turned off, but not a Substantial diffrence.
GNB max ver.2
3.06 P-4 w/HT enabled
512 corsair low Lat.
IBM 80gig raid 0 sata setup

GNB Max-FISR and VCORE

Mt CPU Core Voltage is showing up as 1.42-1.44 in
the Bios & MBM.
Is this a problem?? Should I change it to !.5 or so in
the bios??
The board has Bios 2.2 in it......
CPU temp 50 deg Cel.
Thanks
Mike

Thanks ASSAF for the reply. If 1.42-1.44 is ok I'll
just leave it alone for now....untill CPU and MB ard
broke in.
My GNB Max-FISR is stable . I really like this board.
Thanks
Here's my setup .
Intel P4 2.53/533 c1
MSI GNB Max-FISR
2x256 PC2100 Kingmax
MSI GF4 TI4600 WD 80Gig/7200 8MB
Antec 500W Yamaha CDW-FIE
Creative 52X CD-ROM
SB Audigy
Promise Ultra 133 TX2
WME

GNB Max temps and worries

Okies, I have a question / problem... maybe?
My MB, after being turned off for 30 minutes, on bootup, going DIRECTLY into the Bios, shows, under PC Health, a temp of 51C and climbs to 57..varying to..58.
Now I have the 3.06 GHZ Intel chip.
(No, I really don't care about anyone else's temp if they are overclocking or using something like a 2.4)
No overclocking anything.
Bios 2.2 and I did as Asaaf suggested and changed the thingys to 134 and 1.525.
I have an Alpha PAL8942 - which is supposed to be a decent heatsink on the P4.
IS THIS NORMAL / USUAL or not? If not, then should I take the sink off and re-apply the Artic Silver and try for "better"?
Oh, and MB temp is at 41C. - But I didn't mess with tha because the fan came on the MB attached.
Thank you in advance for your response.

Quote
Originally posted by scorpes
I have a p4 3,06 ghz with standaard P4 cooler and GNB MAX with a total of 6 fans and my normal cpu temp is: 54c and system temp is 35c, and mine cpufan speed is around 3700 rpm (says pcalert)
but if i play a game such as unreal 2003, my cpu is getting very hot: between 80c/85c and my vcore is 1,4
AND MSI SAYS IT'S NORMAL THAT THE TEMPERATURE IS THIS HIGH?
(http://www.msi.com.tw/program/e_service/forum/viewindex.php?threadid=13840&boardid=10&styleid=1)
MSI GNB MAX (ms-6565) motherboard
P4 3,06 ghz processor with standaard p4 cooler
1024 mb DDR 266 mhz (dual) memory
Geforce 4 mx videocard
60Gb Maxtor ATA133 HD
Promedium Mars case with a total of 6 fans
I have had the same problems. The cpu temperature was about 52c when the using was idle.
When the using was more then 80% the temperature was rising in some secons over the 75c.,after replace the cooler there where no more problems. He was not realy good placed on the cpu
Now the temperature is between 46c and 52c.
MSI GNB MAX (ms-6565) motherboard
P4 3,06 ghz processor with standaard p4 cooler
2x512 mb DDR 266 mhz (dual) memory
MSIGeforce 4 ti4800SE
80Gb Maxtor ATA133 HD
60Gb Seagate Baracuda ATA100

GNB Max 2 And USB2.0 Support.. dont have them

Hi there, im having a problem with my USB 2.0 support witrh my GNB Max 2 Motherboard.. I have a pen drive but when i connect it to the PC it says i have connected a high speed drive in a NON high speed usb port. SO i was looking over the internet and noticed that i have no high speed USB . I have seen in the Device Manager -> USB Controllers and theres nothing that says ENHACED.
I hope you can help me to resolve this so i can get HIGH USB on my PC
Thanks in advance!

Hi,
With XP, you have to download the USB 2.0 update from Microsoft........ (Must be a MS XP driver, that know else is allowed to have for download......)
You will have to download from MicroSoft......
OR
Go here......for further help.
XP USB 2.0 INFO
Del UK

Apple's Technical Service Provider complaint and Firewire Target Disk solution

As being my first post, my greetings to the community!
First of all, I would like to clarify that despite I start with a post that includes some negative comments for the Apple's Technical Support Service Provider, which I visited for my problem, I wouldn't like to give the impression that I want to generally spread a negative attitude against them, but only to describe my specific issue. Anyway, only that I haven't visited them so far, after over a 3-year period of using my computer, is a self-explained positive aspect. I've also read that complaints should refer directly to customer's support service, though it is the users with whom I want to share the knowledge resulting from my last experience.
My story/problem has been as following: My computer has failed to boot, I tried some of the tips and advices online and due to the facts that I didn't have the installation disk with me and that I was under stress to recover some of my files, I was urgently needing, I decided to visit an Apple's Technical Support Service Provider. I was hoping for a quick solution, since from the beginning it wouldn't seem to be a hardware failure. I had read about the Target Disk Mode utility and I was at least looking forward to a backup, in case my hard drive was still functioning.
For starters, the provider I finally visited (Sofia, Bulgaria), was not mentioned on the Apple's web page locator. However, I first visited a Reseller, who directed me to the technical service office (other building). Also for starters, I would like to mention that the personnel was totally polite in every case. Now, for the main issue. The technician there connected my laptop via Ethernet cable to another computer, ran a test, which showed that the hardware was working and replied that he cannot know the problem, so I have to leave my computer there for 2-3 days, in order to examine it thoroughly. Luckily, I would leave the country in 2 days and I was needing the files the same day or maximum the following one, so I couldn't follow this option. "Luckily", though, while for the moment I saved 40 euros, the price for examining my problem, regardless spare parts that might would be needed and a value for a backup that I would have might asked. I explained him that I don't have the installation disk with me, just in case he could do the repair disk there, and that I read somewhere that the computer could be connected to another computer via Firewire cable and the hard disk to be seen as an external hard disk, giving me the chance to recover the files I was urgently desiring. The answer to the above was that I can only leave the computer there and I would be informed in 2-3 days. I respect the priority I had to share with other customers, but, on the other hand, to backup 2-3 files and save my life, I don't consider it (specially now that I know) a big of a deal. More important, he wouldn't give me any advice to follow myself. Conservative policy to secure responsibility issues from their part or to secure the payment for a potential check in their house?
First, I didn't try to search for the solution, provided that I didn't have any clue from the technician and that there was no chance to find someone with another mac, but also while I couldn't risk to loose time to search for a backing up solution rather to start immediately with remaking my project (I was using 3ds Max, therefore I could work on a Windows pc). So, following is the next level of my problem and the final solution.
When I got free time, I searched more and while, as I mentioned, I couldn't find another mac, I ended up to the option of being able to mount my mac's hdd to a Windows pc, after using a 3rd-party application (MacDrive in my case) and Firewire cable to link the 2 computers (Target Disk Mode). The result was that the hard disk of my mac was recognised at the Control Panel's Devices, but wouldn't be browsed. It turned to be hard to find information related to my problem, since I guess not many people have faced the exact one. The credits for the solution go here http://www.studio1productions.com/Articles/Firewire-1.htm (thank you so much), were there's an article related to how to solve Windows 7 Firewire issues. The problem was that the Firewire drivers had to switched back to the older version (legacy), which is strange, but it worked perfectly. I'm currently happily backing up my disk.
I hope this post will save time and pain for people having the same issues and I'm sorry for the thorough details I've used in order to describe accurately my concerns.
Cheers!

thanks neil, the laptop originally came with a 10 gig ibm deathstar ata drive which i replaced a couple of years ago with a 40 gig ata. i thought that maybe some necessary drivers weren't installed onto the drive since it isn't an apple branded drive but i couldn't find anything online or on apple's site to confirm that.
the titanium's ATA is controlled via cable select right?

Max define Firewire driver

Hello guys,
I'm trying to do a setup that's going to automatically set a vision test that I've made for a cliente.
Untill this moment I've to:
- install all NI runtimes and program
- activate the licences
- install 3rd party Firewire camera
- go to Max and assign the legacy driver to my camera
My purpose it's to do something that query the user the less as possible.
How can I put Max setting that driver automatically?
Best reagards for all,
Software developer
www.mcm-electronics.com
PS: Don't forget to rate a good anwser ; )
Currently using Labview 2011
PORTUGAL

Hi Jorge,
What can be done is to create an installer with LabVIEW, if you have LabVIEW 8.0 or later, you can use you project to do so. If you don’t have this software installed on your computer(s) you can also export MAX configuration from you development machine and import it on your vision-testing machine.
Be careful about the licensing using for VISION software also, the VISION runtime base licence is limited to three machines.
Best regards,
BRAUD Jean-Philippe
Field Sales Engineer - Nord et Centre France
LabVIEW Certified Developper

"firewire support" and "firewire enabler"

Anyone know where I can download the latest versions of extensions "firewire support" and "firewire enabler" for OS9.2.2? (G4). Thanks.

If the PRAM battery in your G4 is the original battery and has never been replaced, these batteries only last 5-6 years, max.
Also, the PRAM battery can go bad quickly if the your G4 has not been plugged into power and has been off of direct electrical power for a week or more.
This is because the PRAM battery stays charged up with a trickle charge inside a Mac when in is still plugged into a power main. Even if the Mac is shut off, but still plugged into power.
When an older PowerMac has not been plugged into power, there is no trickle charging of the PRAM battery and this battery can permanently lose its power in a short period of time as it is the only power that is keeping the actual current Parameter RAM active until the battery exhausts itself.
A low or dead PRAM battery can cause all sorts of operational weird issues with a Mac.
An inexpensive source of this PRAM battery can be found online here.
http://eshop.macsales.com/item/Newer%20Technology/BAA36VPRAM/

GNB Max-SR MSI-6565 GranetBay & agp440.sys

OK.....first I'll give you my sistem.
Msi-6565(v2.X) Bios version 2.2 All board drivers up to date.
P4 2.53
1G ram Kingmax
2X80Gig WD hard Drives
These are on a Promise Ultra ATA/133 TX2 controller card.
Yamaha CD-RW on board IDE-1
Creative 52X on IDE-2
Audigy
BFG FX5600ULTRA
ANTEC 550 True Control power supply.
OK......Getting a screwup at boot...(sometimes).....Messy graphics.
Have to go into safe mode & shut down. Sometime it takes three or
more tries ...them it takes.
Need a few sugestions here.
I,ve surched the web and have seen no real solution.
ANY sugestions??
Thanks
Jutias

Well...Its morning to me...work 3rd shift.
Anyway. I put the Antec550 in because I thought maybe the BFG FX5600
wasn't getting enough juice. My old power supply only had two molex
line and the antec has 3. So I could use one molex line just for the video card.
Well that was a no go.
Now I 'm just leaving my puter on all the time.
I'm thinking either I have a bad install of the video drivers, or
the video card has bad memory.
No problems before installing the BFG5600.
Was just hoping someone could give me a clue on the "agp440.sys" Error.
Called BFG and they told me that the GranetBay (GNB Max) boards
have issues with the new "FX" video cards.
Thanks
Jutias

GNB Max-L do not power USB

Hi folk!
Recently I has problem. My motherboard GNB2 Max-l (BIOS updated to v2.3) do not give power (5V) to modem connected to USB port (modem not have external power supply and power get from USB). After I power on PC USB LED on modem lighting, but operating system (Windows XP Pro) do not see modem. Support modem manufacturer speak that modem could get power before PC power on. I try some set in BIOS but result was without change. And for modem work properly I need disconnect USB cable from modem and after connect one more. I try on other 2 PC and after some set in BIOS all work properly.
Please advise me way for solving problem.
With kind regards yup.

Kingfisher! Thanx for reply.
Motherboard GNB Max-L (MS-6565 v2.3)
Processor Pentntim IV 2.533 GHz FSB 533 MHz
Memore 2 module 256MB Samsung ( no ECC)
VGA Saphire RADEON 9200SE
DiskDrive Maxtor 6Y120L0 Primary Master
CDRW Asus and DVD RW Pioneer at secondary master and slave
external V.92 (Zyxel OMNI DUO) modem conect to COM2
external USB ADSL modem Zyxel OMNI connected to rear USB
PC without overclocking.
With kind regards yup.

GNB Max and firewire

Similar Messages

Maybe you are looking for