Help using CMS

Hi all,
I have been`studying´about the 2950 switch that we have here at work, and found out that i can connect to a graphical manager (CMS) using http.
I have given the switch an IP on vlan1 and then issued the NO SHUTDOWN to the vlan. my ip works, as i can telne to the switch. However when i try to access CMD i get no response for ages.
I believe that my switch hardware-firmware supports this.
Here is a sample output of my SHOW VERSION :
<b>
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(11)EA1, RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Wed 28-Aug-02 10:25 by antonino
Image text-base: 0x80010000, data-base: 0x80528000
ROM: Bootstrap program is CALHOUN boot loader
Switch uptime is 4 weeks, 4 days, 16 hours, 48 minutes
System returned to ROM by power-on
System image file is "flash:/c2950-i6q4l2-mz.121-11.EA1.bin"
cisco WS-C2950-24 (RC32300) processor (revision G0) with 20402K bytes of memory.
Processor board ID FOC0644Y1RN
Last reset from system-reset
Running Standard Image
24 FastEthernet/IEEE 802.3 interface(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:0B:5F:15:4D:00
Motherboard assembly number: 73-5781-11
Power supply part number: 34-0965-01
</b>
Is there another graphical manager i can use?
Can someone please shed some light on this?
Thank you,
George

Hi again,
I hope i dont sound stupid,
First of all, i can tell you that i am able to ping the switch and get the replies. We are both on the same subnet. My address: 10.51.12.31/24 and the switch is 10.51.12.11/24 .
When you say CMS server you mean the switch i want to connect to....????
You also mention enabling http x.x.x.x of the host on the switch.
Is there a command i need to configure for this and what would this be ???
I am showing here the basic configuration i have so far on the switch, to make troubleshootign easier.
interface Vlan1
ip address 10.51.12.11 255.255.255.0
no ip route-cache
ip http server
snmp-server engineID local server engine id here
snmp-server community my password here
line con 0
line vty 0 4
password my password here
login
line vty 5 15
password my password here
login
end
The rest of the configuration is just the interfaces which have nothing configured on them.
Thanks again,
George

Similar Messages

How to use CMS Users with SAP BOPC NW 7.5

Hello,
I have problems importing and using CMS Users with BO PC 7.5 NW.
I am trying two types of CMS-users
1. CMS Enterprise Users created in CMS and using "Enterprise" authentication
2. SAP BW Users imported into CMS using their SAP authentication "secSAPR3")
but both don't work:
In the BOPC Admin Client, I can succesfully select Security->Users->"Add new Users". Both CMS "Enterprise Users" and CMS Users that use SAP authentication are displayed in the "Everyone" Group.
The CMS Enterprise Users are displayed as <username>, e.g. "Miller".
The CMS users with sap authentication are displayed as <SAPSystem><Client>/<SAPusername>, e.g. "KBE100/Smith".
Now If I try to import a user...
1. CMS Enterprise Users
If can successfully import CMS Enterprise Users and add them to the ADMIN Team, e.g. "Miller".
The problem is they can't be used to log in to the Admin Client and Excel Client:
E.g. I enterUser-ID "Miller" and his CMS-Enterprise-password under password after starting Excel Client, an error message shows up: "The UserID, Password or Domain cannot be authenticated. Go back and make sure you entered valid credentials" ... (same error message as if the user wouldn't exist/wrong pw.).
Seems the user wasn't added as BO PC user. Or do I need to use any prefix before the "user ID" for CMS Enterprise users in the User_ID field instead of just "Miller"?!
2. CMS Users which use SAP-authentication (users imported into CMS from BW and use SAP-authentication)
In the BO PC Admin Client, I can't import them: I go through "1. User Setup" select "KBE~100/Smith", "2. User Detail", "3. Assignments", but if I am in "4. Finish" and click on "Apply", the following error shows up:
"Failed to create directory \root\Webfolders\<AppSetName>\<Appname>" for "KBE~100/Smith".
My guess is that the operating system doesn't like the "/" in the Username - but I guess this can't be changed bc. these Users from CMS and are already displayed with the "/" between SAPSystemID~ClientNummer and username in the User-list in BOPC Admin Client!
side remark: if I create a SAP CMS Enterprise user which contains a "/" in the username (on pupose ), I am getting the same error message.
Any help, explanations and workarounds are greatly appreciated - Any solution will be awarded with maximum points!
Best Regards and thanks a lot for your help!

Hi Florian,
The problem seems indeed the file system on the bw not being able to handle "/". The automatic user import from the bw role into the CMC does not give you an option to replace the "/" character with anything else.
This should solve it:
- Go to the CMC double click the user. Delete the server part "KBE100/" and click save. Make sure the default system is set to "KBE100". The user should now be able to login from BPC with the user Smith.
Good luck,
Martin

Could not see Transport using CMS in Integration Directory

Hi,
I have Changed the Parameter setting to true in Integration Builder for Integration Directory and Integration Repository. When i login into Integration Directory i cannot see the option Transport using CMS in Export. I can only see Transport using File system.
Please help me out in configuring the CMS correctly.
Thanks,
Fahad

Hi Fahad,
This thread answers ur question
CMS Transport mode unavailable in Integration Directory
cheers,
Prashanth
P.S Please mark helpful answers

Transport using CMS between Dev, Qual and Prod

Hi,
I'm a little bit curios if there are others out there using CMS for transport in a XI production line -
Dev -> Qual -> Prod.
My company is using it, and it seems to me that at consolidation stage, you can only select transports related to a SWCV and NOT select transports individually or related to a namespace?
Anyone?
Our version is XI 3.0 SP14 latest patch.
best regards
Torstein Nesby

Hi Torstein,
I saw your other threads related to this as well as your thoughts on 'Quality Feedback' (which I agree with btw). It sounds like you may have been able to come to a resolution to a problem that continues to cause me issues. Can you review and provide some guidance on the following please?
Current Environment / Setup:
- XI 3.0 system, SP12
- Single SLD with appropriate Group / transport Targets setup
- Single IR Track, Single ID Track
- CMS usage for transports. Successful from Dev to QA, QA to Prod has not yet been attempted.
- SWCV are setup in IR and are specific to tech system / product. For example there is a SWCV for Peoplesoft where all related message / data types for Peoplesoft are located. There is another SWCV for SAP, another for Oracle, etc.
- Message Mappings and Interface Mappings are created in the target SWCV. This means that a single interface will normally consist of 2 SWCV to be migrated.
- Currently migrations are bundled in Transport (export) lists vs change lists when migrated out of the Dev environment
- As an aside, I understand the approach of effectively setting up a SWCV per interface with Usage dependencies across SWCV's for reuse of data / message types, however this is the architecture that was recommended at the start of development for this first release.
What I am attempting:
- In the Assemble tab in the transport Studio I want to be able to use a 'Subset Assembly' option to selectively choose which transport / change lists to allow to go to production.
- Based on reading the SAP Help in the XI system, numerous SDN Posts, the SAP docs "Using CMS for XI 3.0" and "How to Transport XI Content Using CMS" it appears this option should be readily available for both the IR AND ID.
Issue:
- For both the IR and ID when I go to the Assembly tab and get the subsequent popup (after "Assemble Components") the "Subset Assembly" option is not visible. Supposedly when going to this Assembly tab, selecting a specific SWCV (not the default 'All Components' option), and choosing "Assemble Components" generates a popup with a checkbox listed for "Subset Assembly". I get the popup in both the IR and ID but the "Subset Assembly" checkbox is not part of the window.
The docs are somewhat unclear in this area. It alludes to seeing this option after the initial migration to Prod is done (which again we have not done yet), but only mentions this in the context of the ID. Another doc alludes to seeing Emergency Transports created in CONS (QA) as if that may be a pre-req to having that option, but is a weak reference.
Can you advise on:
1) Do you see the "Subset Assembly" option in the popup?
2) If so:
a) Did you see it prior to the inital migration to Prod?
b) Do you see it for both the Directory and Repository in the Transport Studio Assembly?
3) Any other thoughts on why I'm encountering this issue?
Thanks for your help!
Darin

LSADMIN CMS authorization problem - How To Transport XI Content Using CMS

We are configuring CMS using the "How To Transport XI Content Using CMS". For the LSADMIN user we have added the SAP_XI_CMS_SERV_USER and SAP_SLD_ORGANIZER roles. We have followed all of the steps in the guide.
The problem we are encountering is that when we define the domain but put in the LSADMIN as the user, we get an error - "SLD (URL http://server:50000) server exception: HTTP response code: 403 Forbidden"
We then gave the LSADMIN all of the roles of XISUPER and restarted the J2EE engine. We still have the same problem. So we changed the CMS User to be XISUPER and we could save the domain. Now, we have another problem - when we try to export from dev using CMS, we get the following problem:
"Sent on 3/9/06 at 1:26 PM: Unable to establish connection to CMS server http://servername:50000. Unable to transfer the following transport lists: Export list for ...
Details: unknown exception: com.sap.cms.util.exception.conf.CMSCFinderException: Workspace name does not exist: com.sap.cms.util.exception.conf.CMSCFinderException: Workspace name does not exist: version=0,dtrWSName=
Check the availability of the CMS and the user authorizations and send the transport request again if necessary
We are on SP16. Anyone encountered this issue?
Regards,
Jay

Here are all of roles we have given LSADMIN in client 100:
SAP_CMS_ADMINISTRATOR
SAP_SLD_DEVELOPER
SAP_SLD_GUEST
SAP_SLD_ORGANIZER
SAP_XI_BPE_MONITOR_ABAP
SAP_XI_CMS_SERV_USER
SAP_XI_CMS_SERV_USER
SAP_XI_DEMOAPP
SAP_XI_DEVELOPER
SAP_XI_DEVELOPER_ABAP
SAP_XI_DEVELOPER_J2EE
SAP_XI_MONITOR
SAP_XI_MONITOR_ABAP
SAP_XI_MONITOR_J2EE
But on the J2EE side, we only see the following roles for LSADMIN:
- Authenticated Users Built-in Group Authenticated Users
- Everyone Built-in Group Everyone
- SAP_XI_CMS_SERV_USER Exchange Infrastructure: Change Management Service User
I checked client 000, and noticed that LSADMIN only had the SAP_XI_CMS_SERV_USER. So this the problem. I added all of the roles to LSADMIN in client 000 and restarted J2EE and now i can see all of the roles under the LSADMIN user in UME.
We noticed the problem that our UME configuration was pointing to client 000 and not client 100. If we go to Visual administrator and go to the Services->UME Provider, we see that - ume.r3.connection.master.client points to client 000. We will need to change this.
That was the issue. UME was pointing to the wrong ABAP client. I appreciate all of your help.
Regards,
Jay

Transports in XI using CMS, assembly issue

Hi all,
We have a 3 system landscape of XI . We have JDI configured in D system.
Currently we are using CMS transports from D to Q and file system transports from Q to P. We have planned to use CMS transports from Q to P also instead of file system transports.
In that process, when we selected a particular software component in the assembly tab, and selected assemble component, we noticed that all the software compoents assembly is running, which are present in the assembly queue.
Is there any procedure to stop the assembly for all the software components?
Thanks.

Transporting Objects
using CMS system. in XI
1. /people/sap.india5/blog/2005/11/03/xi-software-logistics-1-sld-preparation
2. /people/sap.india5/blog/2005/11/09/xi-software-logistics-ii-overview
3. /people/sap.india5/blog/2005/11/28/xi-software-logistics-solution-iii-cms
4. /people/sravya.talanki2/blog/2005/11/02/overview-of-transition-from-dev-to-qa-in-xi --> Overview of Transition from Dev to QA in XI
5. /people/sravya.talanki2/blog/2005/12/20/inconsistencies-while-transporting-rfc-objects-from-dev-to-qa-150-sp12
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/9e76e511-0d01-0010-5c9d-9f768d644808
http://help.sap.com/saphelp_nw2004s/helpdata/en/93/a3a74046033913e10000000a155106/content.htm --> Transporting XI Objects
http://help.sap.com/saphelp_nw04/helpdata/en/ef/a21e3e0987760be10000000a114084/content.htm --> Configuring Groups and Transport Targets

Revert back the transports done using CMS

Hi.
Please let me know how to revert back the transports that are done using CMS.
If once the transport of the namespace has been done from DEV to CONS, can we revert back the transport so that the CONS system will have only those objects that it had before the transport.
I've gone through help.sap.com and some of the forums here regarding transports, but couldn't find the solution.
Please help me out in this regard.
Thanks,
Manohar.

Hi,
It is not possbile revert back the changes that are done using CMS. There is a scope to redo these changes at Oracle database level by redo logs but it is not at all suggestible as it may lead to inconsistencies.
Thanks,
Vijay Kumar T.

Problem in Transport of ID objects using CMS

Hi,
I am using CMS to transport my IR and ID objects from DEV->QA->PROD.
While I am able to transport my repository objects successfully,I do have a problem with trnasport of ID objects.Especially this problem seem to exist only if i try to export individual objects.There isnt any issue for a complete ID transfer which is not my req.
When doing "Release FOr tranpsort" from QA after making the communication channels changes,The object appears in the "assemble " tab.
Ideally Once I assemble the objects,it should diasappear out of assembly page and should be appearing in the "Approval" tab..
But the objects successfully get assembled and dispapper from assembly ,they dont seem to be present in the next approval step.I am unable to track where they are lost.CMS logs doesnt show any error as well.
Any pointers from this issue?
Regards,
Rashmi

Hi,
This will help you,
http://help.sap.com/saphelp_nw04/helpdata/en/93/a3a74046033913e10000000a155106/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/55/7a09d0d7d34b828a9740e322b9222c/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/54/8b5b0555264a93a679c2117fedc748/frameset.htm
This PDF file will help you a lot,
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/f85ff411-0d01-0010-0096-ba14e5db6306
Regards
Agasthuri Doss

Has anyone had success using SharePoint and FrameMaker 10 together using CMS?

Has anyone had success using SharePoint and FrameMaker 10 together using CMS?

Thanks for reminding to at least update the results thus far.
Update 4:
I did get quite a bit of support initially although slowly over a period of a month or so. After Adobe FM support and my SharePoint systems engineer reviewed how FM10 was setup on my computer (which I am the admin for our department’s SP site) and how it interfaces with our SharePoint 2010 Enterprise Edition, there was two conclusions:
Basically Adobe FM Support said that FM10 did not support claims-based authentication and they can no longer help me. They said it will work with FM11 when it comes out.
My SP Systems Engineer, said that FM10 is connecting to SP 2010 just fine but that the FM10 has a software glitch that causes FM10 lose control when executing checkout procedure within FM10. I can checkout and edit that same file in SP with no problems.
About a month later, I upgraded to FM11 and ran into the same problem. I attempted to get Adobe FM Support to help and they said they will look into and get back to me. That was in July and I have not heard anything more from them, and to be honest, my schedule has been extremely busy the last 5 months that I have not had time to pursue it any further.
Needless to say, I was very disappointed with the SP interface and, overall, the lackluster support I received from Adobe. Having a working SP interface was one of the criteria for purchasing TCS3.5 (and subsequent upgrade) in the first place.
One thing of note, we migrated from SP 2007 to SP 2010 in February 2011 and, at the time of Adobe support, I still had access to my SP 2007 site. FM10 and FM11 had to no issues working with SP2007. Unfortunately, SP 2007 is not an option for me anymore.
Also, another observation of FM10/11 not working with SP 2010, it seems that FM10/11 is automatically configured to work with SharePoint Drafts folder locally when connecting to the SharePoint library. This worked just fine with SP 2007 but SP 2010 does not use SharePoint Drafts folder locally the same way (the programming changed, don’t recall where I saw it, probably when searching this issue online) and I suspect that is one of the main issues why it does not work correctly.
So at this time, I have not found a working solution to this problem.

Problem about deploying Enterprise DCs using CMS

hi everyone.
we currently are using NWDS04s sp10.
Using CMS, we transport development DCs to Product System.
However, Enterprise Portal DCs are not being tranmitted.
Other WDJ DC, Dic DC, ExtLib DC, etc. are well transferred.
Is it also possible to send Enterprise Portal DC over CMS?
If possible, pls let us know in which case the Enterprise Portal DC can't be transmitted.

Kindly check this link:
<a href="http://help.sap.com/saphelp_nw70/helpdata/en/c5/56599164d0c04cb566ba0e2d7ed55c/frameset.htm">Transport of Portal objects</a>

Integration Directory - Transport using CMS does not appear

Hi guys,
I'm having problems with one thing I thought it would be trivial.... I'm not able to get the option 'Transport using CMS' in the Integration Directory available.
I've done the necessary steps on the exchangeProfile in order to transport objects using CMS.
1. Configuring ExchangeProfile
IntegrationDirectory
com.sap.aii.ibdir.core.cms.enableTransportWizard=true
com.sap.aii.ibdir.core.cms.enableClTransport=true
IntegrationRepository
com.sap.aii.ibrep.core.cms.enableClTransport=true
com.sap.aii.ibrep.core.cms.enableTransportWizard=true
Added the values to com.sap.aii.ib.client.properties
u2022 com.sap.aii.ibrep.core.cms., com.sap.aii.ibdir.core.cms.
2. And after, I've created the tracks needed for IntegrationRepository and IntegrationDirectory.
For the IntegrationDirectory I've followed SAP's description:
"You have created an XI track in the Landscape Configurator and entered the addresses of the development, consolidation, and productive directory. There are no software component versions in the Integration Directory. Therefore, for directory transports using the CMS, you specify the software component version SAP-INTDIR 3.0 (EXCHANGE DIRECTORY 3.0). This refers to all configuration objects of the Integration Directory.
Once you have made this setting, you can create transport lists for the CMS. The status of the change lists no longer changes to Closed immediately after their release, but first changes to Transportable."
3. I've restarted the J2EE Server.
When I export the objects from IntegrationRepository everything runs OK, but on the IntegrationDirectory I'm not able to have the option 'Transport Using CMS' available.
I've read several threads on the SDN but none of them solved the problem...
Can anyone give me any hint ?

Hi Sameer,
No luck.... There's nothing similiar to what I'm describing and the points which are mentioned i've already covered them.
Thanks for the tip, I was hoping it could give me a push...
Any ideas...?

Help using jar file!

Help using jar file!
Hello
I have created a jar file by using
jar cvmf Manifest.txt myjar.jar 1.class Mydirectory
In 1.java file :I have used
JEditorPane editor;
editor.setPage(getClass().getResource("/Mydirectory/default.htm"));
If I am only giving myjar.jar file to the client without Mydirectory then also it is working fine by showing default.htm in JeditorPane.
But my problem is I want to use
Runtime.getRuntime().exec("cmd /c start IEXPLORE"+targetstr) ;
targetstr will be the filename with path of the default.htm
If I am giving myjar.jar file with Mydirectory to the client it is working but I don't want to give Mydirectory to the client .
What should I do?
Is there any solution for this?
Using another jar file which will include mydirectory can solve this problem?
Is there any othe concept in java so that I wll be able to hide Mydirectory from client?
Please help.

It seems like you could extract the .htm file from the jar, either with Runtime.exec or using the Jar API classes.

Help using file sharing with different users accounts on same Macbook

Hi, I just wanted a little help using the file sharing option. My wife and I had different users accounts on the same MacBook, but when I am trying to share my baby's picture from my documents folder for my wife to have the same picture, I can't find the way to do that; I am not been able to find my pictures on my wife's account. Is there any way that I could share a folder from my account and my wife to have the same files at the same time on her account?
I mean, something like the smart play list on the itunes?
Thank you

You can't do that directly unless you change permissions on your whole Documents folder which is not a good idea. Your wife can see your Documents folder from her account by going to Users/yourusername/Documents. However, this folder has no read privileges for others except yourself by default so she won't be able to open it.
rather than changing permissions on your Documents folder, you can place the pictures you want to share in Public folder in your home directory or in Users/Shared folder.

How to assign search help using ovs for select options for ALV in web dynpr

how to assign search help using ovs for select options for ALV in web dynpro

Hi,
refer http://wiki.sdn.sap.com/wiki/display/WDABAP/InputhelpofObjectValueSelectioninWDABAP
http://www.****************/Tutorials/WebDynproABAP/OVS/page1.htm
and http://wiki.sdn.sap.com/wiki/display/Snippets/WebDynproAbap-OVSsearch+help
Thanks,
Chandra

I need help using SSO (built in)

Hi folks,
I'ld like to use the built in SSO of Sun App Server 7 for my intranet, which consists of two applications App-A and App-B. App-A is the main application (intranet), from where App-B (CMS) can be invoked.
Both applications are secured bei FORM based authentication.
SSO seemed to work fine for this applications first, BUT than I had to learn, that it App-A looses it's session middle in the work, sometimes. Investigating into this behavior I found out, that this happens only and always, when App-B (CMS) has been used before.
In this case App-B is running into a timeout, after a while (30 min.). This is o.k. so far and what I expected. BUT, I did not expect, that the timeout of App-B also destroyes session of App-A, regardless that I continue to use App-A.
In my real szenario this means, that users of my intranet (App-A) always loose their session half an our after using CMS (App-B), even if the continue to use intranet!
The worst case is, if they use CMS, close it than and open a second CMS session, after a while.
If they do this, before the first CMS-session times out, the second CMS session is killed shortly after starting it and middle in the work (together with the intranet, of course). Of course entered data is lost, than.
This is not what I expect from a usefull SSO feature und makes it almost useless for me.
I cannot believe, that this is o.k. and that nobody else got problems with this behavior.
Does anybody know this behavior? If yes, how do you deal with this?
Best regards,
Harald

Bluetooth and WiFi are two different, unrelated radio technologies. Bluetooth is used to connect to wireless keyboards, mouses, cell phones etc. You want to look at your 802.11 g (or b or n) wireless to find other computers or routers. The icon symbol for that looks different.
Go to System Prefs/Network/ and click on Airport. then check the little box to "Show Airport status in menu bar".

Help using CMS

Similar Messages

Maybe you are looking for