Homehub 3.0 Wireless Event Log messages

Hello,
Can anyone tell me what event log messages like the following mean?
3 consecutive beacons have not been transmitted
I'm getting these about once every 20 minutes. Smart Wireless is enabled.
A couple of days ago Wireless became unstable, devices connecting and reconnecting repeatedly. The Wireless light was randomly flashing on and off (Blue) every few seconds. I had to restart the homehub (which I didn't really want to do, as I was still within my first 10 days, with Infinity). But after the restart, the admin password had changed. I assumed it was reset to the original one, but that was also not recognised. I had to do a password override to get access.
Ever since then Wireless has been behaving itself but I'm still left with these strange event log messages - google comes up with nothing.
Any ideas?

Hi BRunner and welcome
Although I've not had opportunity to obtain one of these hubs (BT are you listening), as I'm still on the hub 2, I'll try to help you out with this...
It looks like the hub is reporting that it can't transmit the wireless signal on the chosen channels, why, I'm not too sure
(this might be due to the design (how 'Smart Wifi' works), or dare I say it, the hub could be faulty!!!!!)
Firstly, download either inSSIDer2 (Windows) or istumbler (MAC) - take care when installing, uncheck any 'additional freebies' as they're not needed.
Either will show all the wireless SSIDs in your area. As I use inSSIDer2, I'll explain what to do using this one, I guess itsumbler would be similar (not a MAC man, yet!)
Disconnect from your own hub, run inSSIDer and monitor any SSIDs, I recently noticed that 2 of my neighbours (VM) routers appears to grab channel 1 upto channel 7!
This keeps changing and they keep fighting with each other. As this was affecting me, I've moved to channel 8. This can be manually set via the hub manager, but you'd probably need to switch off 'Smart Wifi'
Ideally, take a screenshot of the results BUT remove ANY wireless SSID's, it's the channels in use that's important.
-+-No longer a forum member-+-

Similar Messages

Help Needed-bt home hub 2.0 event log messages

Hi, Please can someone have a look at the event log messages below. Is someone trying to hack me? there are loads more of these messages i've only copy and pasted a few of them.
many thanks in advance.
12:32:02 30 Sep
VOIP: [2.0A] [guest1] [-] REGISTER - SIP message received
12:32:02 30 Sep
VOIP: [2.0A] [guest] [] 501 Not Implemented - SIP message sent
12:32:02 30 Sep
VOIP: [2.0A] [guest] [-] REGISTER - SIP message received
12:32:02 30 Sep
VOIP: [2.0A] [office12345] [] 501 Not Implemented - SIP message sent
12:32:02 30 Sep
VOIP: [2.0A] [office12345] [-] REGISTER - SIP message received
12:32:02 30 Sep
VOIP: [2.0A] [office1234] [] 501 Not Implemented - SIP message sent
12:32:02 30 Sep
VOIP: [2.0A] [office1234] [-] REGISTER - SIP message received
12:32:02 30 Sep
VOIP: [2.0A] [office123] [] 501 Not Implemented - SIP message sent
12:32:02 30 Sep
VOIP: [2.0A] [office123] [-] REGISTER - SIP message received
12:32:02 30 Sep
VOIP: [2.0A] [office12] [] 501 Not Implemented - SIP message sent
12:32:02 30 Sep
VOIP: [2.0A] [office12] [-] REGISTER - SIP message received
12:32:02 30 Sep
VOIP: [2.0A] [office1] [] 501 Not Implemented - SIP message sent
12:32:02 30 Sep
VOIP: [2.0A] [office1] [-] REGISTER - SIP message received
12:32:02 30 Sep
VOIP: [2.0A] [office] [] 501 Not Implemented - SIP message sent
12:32:02 30 Sep
VOIP: [2.0A] [office] [-] REGISTER - SIP message received
12:32:02 30 Sep
VOIP: [2.0A] [admin12345] [] 501 Not Implemented - SIP message sent
12:32:02 30 Sep
VOIP: [2.0A] [admin12345] [-] REGISTER - SIP message received
12:32:02 30 Sep
VOIP: [2.0A] [admin1234] [] 501 Not Implemented - SIP message sent
12:32:02 30 Sep
VOIP: [2.0A] [admin1234] [-] REGISTER - SIP message received
12:32:02 30 Sep
VOIP: [2.0A] [admin123] [] 501 Not Implemented - SIP message sent
12:32:02 30 Sep
VOIP: [2.0A] [admin123] [-] REGISTER - SIP message received
12:32:02 30 Sep
VOIP: [2.0A] [admin12] [] 501 Not Implemented - SIP message sent
12:32:02 30 Sep
VOIP: [2.0A] [admin12] [-] REGISTER - SIP message received
12:32:02 30 Sep
VOIP: [2.0A] [admin1] [] 501 Not Implemented - SIP message sent
12:32:02 30 Sep
VOIP: [2.0A] [admin1] [-] REGISTER - SIP message received
12:32:02 30 Sep
VOIP: [2.0A] [admin] [] 501 Not Implemented - SIP message sent
12:32:02 30 Sep
VOIP: [2.0A] [admin] [-] REGISTER - SIP message received
12:32:02 30 Sep
VOIP: [2.0A] [administrator] [] 501 Not Implemented - SIP message sent
12:32:02 30 Sep
VOIP: [2.0A] [administrator] [-] REGISTER - SIP message received
12:32:02 30 Sep
VOIP: [2.0A] [4260011834] [] 501 Not Implemented - SIP message sent
12:32:02 30 Sep
VOIP: [2.0A] [4260011834] [-] REGISTER - SIP message received
12:32:02 30 Sep
VOIP: [2.0A] [Administrator] [] 501 Not Implemented - SIP message sent
12:32:02 30 Sep
VOIP: [2.0A] [Administrator] [-] REGISTER - SIP message received
12:32:02 30 Sep
VOIP: [2.0A] [3942121793] [] 501 Not Implemented - SIP message sent
12:32:02 30 Sep
VOIP: [2.0A] [3942121793] [-] REGISTER - SIP message received
12:32:02 30 Sep
VOIP: [2.0A] [100] [] 404 Not Found - SIP message sent
12:32:02 30 Sep
VOIP: [2.0A] [100] [-] OPTIONS - SIP message received
12:32:01 30 Sep
SNTP Synchronised to server: 213.123.26.170
11:45:07 30 Sep
VOIP: [2.0A] [100] [] 404 Not Found - SIP message sent
11:45:07 30 Sep
VOIP: [2.0A] [100] [-] OPTIONS - SIP message received
11:32:01 30 Sep
SNTP Synchronised to server: 213.123.20.170
11:28:34 30 Sep
VOIP: [2.0A] [100] [] 404 Not Found - SIP message sent
11:28:34 30 Sep
VOIP: [2.0A] [100] [-] OPTIONS - SIP message received
Solved!
Go to Solution.

Hi JM7HUB and welcome,
No, you're not being hacked. It's to do with BTHub phone (Broadband Talk - BBT) and the hub, in your case the hub 2A.
It's a test that BT seem to carry out, normally (IIRC) after a reboot of the hub or possibly at random times - it's been a long time since I used BBT. I'll guess there are some random names mentioned on some of the other VOIP events?
If you don't use a BBT, you can turn this off by entering the hub manager - type bthomehub.home or 192.164.1.254 in to your browser, click settings, advanced settings, continue to adavnced settings, telephony - there should be an option there to turn it off. This should then stop the events.
edit. The telephone light on the hub will go out, but any registered hub phone should still operate as a 'normal' phone using your landline number.
-+-No longer a forum member-+-

Problems with using System.Diagnostics.EventLog to retrieve event log messages

Hi
In my app I am retrieving error and critical events from application and system log - but for some reason what it is returning doesn't tally with what I see in event viewer
For example:-
1) Source is SideBySide and shows in event viewer with Event ID of 33 - but in my app it is returning an event ID of 3238068257 - all other details such as message are correct - other event sources show fine
2) A lot of the system event log messages are showing wrong error message - in event log it shows correctly but in my app it is retrieving messages like this "The description for Event ID '41' in Source 'Microsoft-Windows-Kernel-Power' cannot be
found. The local computer may not have the necessary registry information or message DLL files to display message, or you may not have permission to access them" - I am running the app with admin rights?, so not sure why not showing same message as it
shows in event viewer i.e "The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly."
Darren Rose

Private Sub btnCheckEventLog_Click(sender As Object, e As EventArgs) Handles btnCheckEventLogs.Click
' get event logs
' APPLICATION LOG
' variables for adding to the listview application log
Dim ListEventlogApp As ListViewItem
Dim arrayEventlogApp(5) As String
' Clear existing items from list
lvwEventLogApp.Clear()
' Create columns and set width
lvwEventLogApp.Columns.Add("Date/Time", 120)
lvwEventLogApp.Columns.Add("Type", 50)
lvwEventLogApp.Columns.Add("Source", 150)
lvwEventLogApp.Columns.Add("ID", 100)
lvwEventLogApp.Columns.Add("Message", 1000)
' get event log (application) error entries
Dim eventLogAppError As New System.Diagnostics.EventLog("Application")
Dim eventCntr1 As Integer = 1
Dim numberofeventstoshow1 As Integer = 1
For i As Integer = eventLogAppError.Entries.Count - 1 To 0 Step -1
Dim eventLogAppErrorEntry As EventLogEntry = eventLogAppError.Entries(i)
If eventLogAppErrorEntry.EntryType.ToString = ("Error") Then
arrayEventlogApp(0) = (eventLogAppErrorEntry.TimeGenerated)
arrayEventlogApp(1) = (eventLogAppErrorEntry.EntryType.ToString)
arrayEventlogApp(2) = (eventLogAppErrorEntry.Source)
arrayEventlogApp(3) = (eventLogAppErrorEntry.InstanceId)
arrayEventlogApp(4) = (eventLogAppErrorEntry.Message)
ListEventlogApp = New ListViewItem(arrayEventlogApp)
lvwEventLogApp.Items.Add(ListEventlogApp)
eventCntr1 = eventCntr1 + 1
If numberofeventstoshow1 = 10 Then Exit For ' amend if you want to show more than 10 events
numberofeventstoshow1 = numberofeventstoshow1 + 1
End If
Next
' SYSTEM LOG
' variables for adding to the listview application log
Dim ListEventlogSys As ListViewItem
Dim arrayEventlogSys(5) As String
' Clear existing items from list
lvwEventLogSys.Clear()
' Create columns and set width
lvwEventLogSys.Columns.Add("Date/Time", 120)
lvwEventLogSys.Columns.Add("Type", 50)
lvwEventLogSys.Columns.Add("Source", 150)
lvwEventLogSys.Columns.Add("ID", 100)
lvwEventLogSys.Columns.Add("Message", 1000)
' get event log (system) critical entries
Dim eventLogSystemCritical As New System.Diagnostics.EventLog("System")
Dim eventCntr2 As Integer = 1
Dim numberofeventstoshow2 As Integer = 1
For i As Integer = eventLogSystemCritical.Entries.Count - 1 To 0 Step -1
Dim eventLogSysCriticalEntry As EventLogEntry = eventLogSystemCritical.Entries(i)
If eventLogSysCriticalEntry.EntryType.ToString = ("0") Then
arrayEventlogSys(0) = (eventLogSysCriticalEntry.TimeGenerated)
arrayEventlogSys(1) = ("Critical")
arrayEventlogSys(2) = (eventLogSysCriticalEntry.Source)
arrayEventlogSys(3) = (eventLogSysCriticalEntry.InstanceId)
arrayEventlogSys(4) = (eventLogSysCriticalEntry.Message)
ListEventlogSys = New ListViewItem(arrayEventlogSys)
lvwEventLogSys.Items.Add(ListEventlogSys)
eventCntr2 = eventCntr2 + 1
If numberofeventstoshow2 = 10 Then Exit For ' amend if you want to show more than 10 events
numberofeventstoshow2 = numberofeventstoshow2 + 1
End If
Next
' get event log (system) error entries
Dim eventLogSystemError As New System.Diagnostics.EventLog("System")
Dim eventCntr3 As Integer = 1
Dim numberofeventstoshow3 As Integer = 1
For i As Integer = eventLogSystemError.Entries.Count - 1 To 0 Step -1
Dim eventLogSysErrorEntry As EventLogEntry = eventLogSystemError.Entries(i)
If eventLogSysErrorEntry.EntryType.ToString = ("Error") Then
arrayEventlogSys(0) = (eventLogSysErrorEntry.TimeGenerated)
arrayEventlogSys(1) = (eventLogSysErrorEntry.EntryType.ToString)
arrayEventlogSys(2) = (eventLogSysErrorEntry.Source)
arrayEventlogSys(3) = (eventLogSysErrorEntry.InstanceId)
arrayEventlogSys(4) = (eventLogSysErrorEntry.Message)
ListEventlogSys = New ListViewItem(arrayEventlogSys)
lvwEventLogSys.Items.Add(ListEventlogSys)
eventCntr3 = eventCntr3 + 1
If numberofeventstoshow3 = 10 Then Exit For ' amend if you want to show more than 10 events
numberofeventstoshow3 = numberofeventstoshow3 + 1
End If
Next
End Sub
Darren Rose

Listing of controller Event log messages?

Does anyone know where to find a listing of the Controller event log messages?
I've got a device that is failing to associate for "ReasonCode 2" but I can't figure out what ReasonCode 2 is.
thanks-
Lynne

Thanks for your response.
No, I did not see any authentication messages.
The person who was having the association problem is now working; nothing changed on either the controllers or the client.
I was hoping to find a reference for all the codes so I could look this stuff up myself.
If you happen to know where I could find that I would greatly appreciate it.
Lynne

Event log message

Hi,
Looking at the event log for my hub (3.0), in the system category, I spotted the following:
STP Alert: Port eth0 leaving blocking state
Does anyone know what this means?
Thank you very much,
Steve
Solved!
Go to Solution.

Welcome to this forum.
Its a Spanning Tree Protocol alert. It usually means that somehow you have created an Ethernet loopback condition.
This can be caused if you connect more than one Powerline adapter to the home hub, or if you have somehow connected two home hub LAN ports to the same Ethernet switch. This can cause all sorts of problems.
The affected Ethernet port (0) had been blocked.
What do you have connected to the Ethernet ports of the home hub?
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Messages in event log about processor speed limited by system firmware

On my new G50-80 I get the following event log messages: "The speed of processor 0 in group 0 is being limited by system firmware. The processor has been in this reduced performance state for 71 seconds since the last report." and this repeats for all 4 processors, on every startup.What does this mean and how to fix? The BIOS is factory original (version BOCN73WW)I have not tweaked speedstep and so on (yet), the machine is on AC power.and I don't know what's DOS, and is it much worse than DDOS. Thanks,-- dd

hi dd,
Is this item your laptop?
If yes, when the machine is plugged-in and running on High Performance power plan, can you try to open a few graphics intensive applications and observe the CPU frequency if it reaches 2.4Ghz or goes into to 3Ghz (turbo boost).
If you don't have graphics intensive apps, try to:
1. Download and install Heavyload and run a stress test on the CPU.
2. Run Coretemp and observe the frequency and the temperature on the cores #0,1,2,3
It'll also help if you can post a screenshot of the results. As for the disk percentage being high, it's likely that there's an app running in the background that's constantly writing to the drive (i.e. Antivirus software running a scan in the background ro a torrent app downloading in the background).

Error messages in modem/router event log

Share on facebook Share on twitter Share on email Share on print More Sharing Services 2 Hi folks. Just purchased a new wireless cable modem/router from Telstra (Gateway Max - Netgear C6300BD-1TLAUS). I've just noticed the following messages in the Event Log. Is there something wrong and, if so, what's causing it? TimePriorityDescription Sun Jun 21 13:34:47 2015 Error (4) DHCP RENEW WARNING - Field invalid in response v4 option;CM-MAC=25:2a:8c:de:74:e8;CMTS-MAC=00:00:84:a0:1b:54;CM-QOS=1.1;CM-VER=3.0; Sun Jun 21 11:44:19 2015 Critical (3) Started Unicast Maintenance Ranging - No Response received - T3 time-out;CM-MAC=25:2a:8c:de:74:e8;CMTS-MAC=00:00:84:a0:1b:54;CM-QOS=1.1;CM-VER=3.0; Sun Jun 21 09:34:47 2015 Error (4) DHCP RENEW WARNING - Field invalid in response v4 option;CM-MAC=25:2a:8c:de:74:e8;CMTS-MAC=00:00:84:a0:1b:54;CM-QOS=1.1;CM-VER=3.0; Sun Jun 21 04:46:49 2015 Critical (3) Started Unicast Maintenance Ranging - No Response received - T3 time-out;CM-MAC=25:2a:8c:de:74:e8;CMTS-MAC=00:00:84:a0:1b:54;CM-QOS=1.1;CM-VER=3.0; Sun Jun 21 01:34:47 2015 Error (4) DHCP RENEW WARNING - Field invalid in response v4 option;CM-MAC=25:2a:8c:de:74:e8;CMTS-MAC=00:00:84:a0:1b:54;CM-QOS=1.1;CM-VER=3.0; Sat Jun 20 16:12:38 2015 Critical (3) Started Unicast Maintenance Ranging - No Response received - T3 time-out;CM-MAC=25:2a:8c:de:74:e8;CMTS-MAC=00:00:84:a0:1b:54;CM-QOS=1.1;CM-VER=3.0; Sat Jun 20 13:34:47 2015 Error (4) DHCP RENEW WARNING - Field invalid in response v4 option;CM-MAC=25:2a:8c:de:74:e8;CMTS-MAC=00:00:84:a0:1b:54;CM-QOS=1.1;CM-VER=3.0; This is just a sample of the log file - it's much longer than this. Appreciate any help you can provide. Thanks.NOTE: MAC addresses above have been changed )...just to be safe. :-)

Hi Turbo, have u called and what was the response, if any? I have exactly the same error messages and my connection drops out every 24 to 48 hours without fail. Windows's Event Viewer and Intel's ProSet Diagnosis confirms that the computer was NOT being assigned an IP address. Setting a Static IP on the Local Machine does not help either. I have called them and they wanted to send out a tech. I refused because it seems very much to me that this is a software issue, either with the affected computer or with the Gateway's firmware. Doesn't sound like hardware or the pit in the street. The technician would have come and Telstra would have charged me for the visit I felt. Fred

Lots of Anyconnect Error Message in Windows Event Log

Hi Community.
We have lots of Anyconnect Error Messages in the Windows Event Log. Following two examples.
Can anyone tell me why these errors appears and how do I fix them ? I already installed the newest Anyconnect on my machine.
Thanks in advance and Kind Regards Patrick
Example 1
<Provider Name="acvpnagent" />
<EventID Qualifiers="9216">2</EventID>
<Keywords>0x80000000000000</Keywords>
<EventRecordID>97564</EventRecordID>
<Channel>Cisco AnyConnect Secure Mobility Client</Channel>
- <EventData>
<Data>Function: CNetEnvironment::logProbeFailure File: .\NetEnvironment.cpp Line: 1432 Invoked Function: CHttpProbeAsync::SendProbe Return Code: -27066354 (0xFE63000E) Description: HTTP_PROBE_ASYNC_ERROR_CANNOT_CONNECT HTTP (host: 109.164.211.237)</Data>
</EventData>
Example 2
<Provider Name="acvpnagent" />
<EventID Qualifiers="9216">2</EventID>
<Keywords>0x80000000000000</Keywords>
<EventRecordID>97565</EventRecordID>
<Channel>Cisco AnyConnect Secure Mobility Client</Channel>
- <EventData>
<Data>Function: CNetEnvironment::TestAccessToSG File: .\NetEnvironment.cpp Line: 1385 Invoked Function: CNetEnvironment::analyzeHttpResponse Return Code: -28966899 (0xFE46000D) Description: NETENVIRONMENT_ERROR_PROBE_INCOMPLETE:Network Probe could not contact target</Data>
</EventData>

HI and welcome to Discussions,
in my personal opinion there is not much for you to worry about.
The 'Windows Tool for the elimination of malware' is nothing you miss as long as you have a decent Anti-Virus Software running.
The update for the IE 7 might be missing an installed IE 7, which can do by downloading it yourself from Microsofts webpage.
If you don't use the IE but something like Firefox or Opera or Safari, than don't bother with these update.
Stefan

File history stopped working after a warning message in the event log

I have encountered this twice that File history stopped working, the event log says:
Unusual condition was encountered during finalization of a backup cycle for configuration C:\Users\xxxx\AppData\Local\Microsoft\Windows\FileHistory\Configuration\Config
If I re-run it, it consumes the backup disk space but still failed to backup.
I have to manually delete all backup, turn off File History and re-configure it again to make it work.
This happened twice already, so all my file history lost after re-config.
Anyone encounter the same situation?

MICROSOFT is plagued by idiots!!!!
- Just turn it off
- then click "select drive"
- and when it asks you the retarded question... just click >>>>>"NO"<<<<<<< -_-
Seriously... this is the answer.... frigging retards at microsoft... to think it takes an army of programmers and billions of dollars to create such idiocy!
http://answers.microsoft.com/en-us/windows/forum/windows_8-performance/cannot-change-drive-in-file-history-windows-8/6dbeca54-d05e-4f93-9262-45a56d6a82d1?page=2&msgId=f1792c5e-c5d0-4163-b449-c7165d72f88d&tab=question&status=AllReplies&status=AllReplies%2CAllReplies
I cant believe these morons put everyone through such hell and then don't even bother to follow up with the correct solution.
To top it of the moron moderator marks this as an answer??!!!
What a pathetic joke - I hope everyone reads this message before being punished by the miles of bullcrap in this thread -_-
Microsoft = ridiculous
Thanks! I guess the TL;DR version is "to change your file history drive you need to discard the current temp files."
Exactly :)
It's the bad wording in the messages.
the first message (which I can only vaguely remember so can't quote exactly) that gives you the impression you can continue
something but doesn't make clear that to so will need the "old drive" configured the way the "old drive" was.
Then the next message is just confusing:
“we can't copy files to this location. Your current File History drive is disconnected. Reconnect the drive and try again”
sounds like
“we can't copy files to this location. [because there's a problem with the new location]
Your current File History drive is disconnected. [the new location is disconnected]
Reconnect the drive and try again [reconnect your new location and try again]”
When it should be reworded to say something along the lines of (in more formal language):
"You asked us to continue...give us the drive you were previously using...or if it's no longer available, click here to start from scratch"
(I know that's all the opposite of tldr but I'm trying again to put into words what I think was happening).

Log Messages from Transaction Event Logger

I have 4 instances of MII v12.1 and within a transaction I want to add a message to the log when the transaction runs so I can view it through the message logger. All 4 MII instances were installed by the same consultant a few years ago so there "should" be no differences in the log configs. On 3 of the instances this is working fine - I have created a very simple transaction with one Event Logger action configured with a message "Test Message" and when I execute the transaction I see the correct entry in the log viewer. On the fourth however, although the transaction executes without error I am not seeing anything in the viewer for this event. I am using the standard "last 24 hours" log viewer with no filters and no specific log locations selected, and no customisations. I am seeing other system generated messages. I found some documentation about logging and the viewer and I found the Netweaver log config but as far as I can see it looks consistent between the instance which is working and the one which is not working. Is there some other config which needs to be done to enable Event Logging from transactions? My user has the same access across all instances. Any guidance would be appreciated. I attach a screen shot of what I am expecting to see (taken from one of the instances which is working).

Hi Partha
Many thanks for your reply. I have tried this and unfortunately it makes no difference. I also checked on the other instances and found they have their tracing levels all set to error, not Info. I have also noticed that on the instance which is working, in the System Configuration section at the bottom of the Log Config page - for Applications and all sub categories I see the entry .\log\applications_00.log in the Pattern column. On the instance which is not working I see that entry for the Applications root but not for any of the sub categories (even after selecting Copy to subtree). I cannot see where I can set this value (there is no modify function available, even under Administrator login).
Also, when I look at the log messages which have generated when setting the Event Type to Error on the instance which is not working, it shows one entry and the Category and Location columns show <com.sap.xmii.bls.executables.action.logging.LoggingActions>. When I generate an event with type Error on the instance which is working I get 2 log messages, one with the Category and Location <com.sap.xmii.bls.executables.action.logging.LoggingActions> and the other with Category /Applications/XMII/Xacute/Event and Location <com.sap.xmii.bls.executables.action.logging.LoggingActions>.
I guess that the .\log\applications_00.log should be showing for all subtree items under Applications and because it is not then the messages are not going into any application log. Not sure how to fix this however.
I have also reset to the default configuration and it does not change the above.
Best Rgds
Richard

Date format in log/error messages with Server Event Log

Hi :)
I have some question.
Current Date is printed at tterrors/ttmesg log files to add with "-showdate" option at $TIMESTEN_HOME/info/ttendaemon.options file.
But date when the TimesTen Server Event Log output is not displayed.
How to solve these case?
====
ttmesg.log
====
2010-05-17 09:40:00.11 Info: : 7409: maind: done with request #433.1657
09:40:00.13 Info: SRV: 31875: EventID=16| Connect succeeded from client: ttwell01 (ttwell01); IP address: 218.234.33.27; Client PID: 31870; DSN: ntsdb; UID: timesten
2010-05-17 09:40:27.84 Info: : 7409: maind got #434.1658, hello: pid=32076 type=utility payload=%00%00%00%00 protocolID=TimesTen 7.0.5.9.0.tt7059 ident=%00%00%00%00
====
====
ttendaemon.options
====
# Commented values are default values
#-supportlog /home/TimesTen/tt7059/info/ttmesg.log
#-maxsupportlogfiles 10
#-maxsupportlogsize 0x100000
#-userlog /home/TimesTen/tt7059/info/tterrors.log
#-maxuserlogfiles 10
#-maxuserlogsize 0x100000
-showdate
-verbose
-oracle_home /home/oracle11g
# Start the TimesTen OracleConnect GUI
-webserver
-server 17593
====
OS
====
Red Hat Enterprise Linux AS release 4 (Nahant Update 5)
Thanks
GooGyum

This is an issue that was discussed internally very recently. BUG 9719650 - -SHOWDATE OPTION NOT ENABLED FOR SRV MESSAGES has been logged to track the issue.

IVR - messages failed to be written in event log

Hi everybody,
we have some errors occuring on our IVR which is based on a Cisco AS5350XM. It sends the following SYSLOG messages:
%VOICE_ELOG-3-MSGDROPPED: 4 messages failed to be written in event log (client id:AC4, dump url:)
%VOICE_ELOG-3-MSGDROPPED: 10 messages failed to be written in event log (client id:AC3, dump url:)
The device and the IVR function seem to run normally but i keep getting these Syslog messages. Has anybody an idea how to solve the problem or where the problem could lie?
Kind Regards,
Jannik

Hi,
best support in that case: have a look into the enhancement documents on SERVICE.SAP.COM/INSTGUIDES -> xapps- xapps mobile -> xMAM XX
There you will find a great step by step walkthrough how to do that.
Hope it helps!
Regards,
Oliver

Raid performance deteriorates, looses drive, but no messages in event log

We have a PATA XServer Raid running, which was fine until a few weeks ago. Suddenly performance tanked, writing a 70 MB file via a 100 Mbps network would take an hour.
The Raid volume, a 6 drive 250 GB raid with one hotspare, had 100 GB left.
First we thought it was the network, there was a loose DHCP server, but nothing was available that could really explain the performance deterioration. The only thing that was noticed was that with Helios Lan test the first write to the raid would take more time as the subsequent writes. So we decided to upgrade the firmware and do a volume test, with diskutility. That gave a interleaf problem.
After upgrading the network (which was planned anyway) to 1 GBps, we rebooted the Xserve and the Raid. Now, the 6th drive had an orange status in Raid Admin, a warning, saying it was part of an Unknown Array. The 7th drive, the hot-swap, was now part of the Raid.
The strange thing is that in the event log there are no messages what so ever about a failed drive, nor any other messages relating to this. All I get is Coprocessor offline/Online, Raid Controller Restarted and Riad Controller 1 Fibre LIP, and Firmwareupdate
I also noticed that the time was off to local time, so I synchronized both to time.euro.apple.com.
Shouldn't we be getting messages something is very wrong in the event log?
XServe G5 Xserve Raid Mac OS X (10.3.9)

We updated the firmware to 1.5.1. After that, the network switch was replaced by a 1Gbps switch, and the XServe and the XServe raid were rebooted. After that one of the people discovered that disk 6 had an orange led burning.
XServe G5, XServe Raid Mac OS X Server (10.3.9) Raid Firmware 1.5.1

BT NetProtect Plus Error message in event log - mf...

Hi,
Anyonwe know why I am getting a warning in the system event log as follows
"Process **\MCSHIELD.EXE pid (2588) contains signed but untrusted code, but was allowed to perform a privileged operation with a McAfee driver."
Source: mfehidk
Event Id: 516
I am also getting the following error
"Unable to start a DCOM Server:{3A65891C-3794-43E5-89C8-20CCD19902CE}. The error: "740"
Happened while starting this command:
"C:\Program Files (x86)\McAfee\Supportability\MVT\MvtApp.exe" -Embedding"
Source: DistributedCOM
Event ID: 10000
Thanks
Mick

Hi,
You may check this:
XL Reporter Server Error Log - Please Help
Thanks,
Gordon

Questions about BT Home Hub 4A event log - WIFI c...

Hope someone can help please ?
I had BT inifinity installed 2 weeks ago with the HH 4 (type A) and everything has worked - connection found, no problem.
This week, my ipod touch was unable to join the network but the iphone 5, another ipod and a tablet could connect without a problem. The ipod touch managed to connect to another WIFI used at the property and my work wifi without a problem.
I thought it maybe the ipod touch as it was quite old but that doesn't make sense since it connects fine to other networks. I restored network settings and other options suggested by Apple but to no avail.
I have turned my attention to the Hub. My laptop (older than the ipod touch) gets the connection no problem along with the other devices. I went into the hub management page but I am not smart enough to decifer the event log so would like some help so I can fix this because I thought BT infinity was the better more reliable option?
The ipod touch Wifi IP address is 00:25:00:b7:35:f6.
On the event log, it shows STA before the address - but it shows STA before all the device IP addresses. Should I change this to DCHP ? or is this (Static ? alright)
The Lease on all the devices on the event log is set to 1440 min. (1 day) is that alright too, what does it mean ?
Do I have to keep renewing the lease ? How do I do that ? I read it can be set to 21 days ?
Going back to the IP address on the ipod it shows the Hostname as 00:25:00:B7:35:f6-2 this is different to the IP address with the -2. Could that be a cause of the unable to join network or is it because I attempted to recreate the network on the ipod so its the second version of that host name ?
Is there any setting I can change to fix this because I am concerned the same this will happen to the other devices and then the laptop....
What do I need to do to be able to get my ipod touch to connect to the BT network setting ?
I think its the hub 4A causing the 'block' on the ipod touch not the device and I think its maybe a matter of changing a setting - but then why was it all fine before when Infinity was first installed ?
Lastly my laptop (7 Years old) seems to be attached to the 5GHZ Wireless channel - is that alright ? The other more recent devices are on the 2.4ghz channel (except the ipod touch which isn't on any !!)
Is it alright to turn the hub on / off ? -I am resisting that because I don't want to make the situation worse.
Sorry but what does client disassociated mean and all the BLOCKS - do they relate to firewall ?
Please can you review the event log and my questions ?
Many thanks
angie 2601
The time frame is 3.55am 8/8/2013 - 7.16 am 8/8/2013
(Latest (7.16am) at the top
Message
07:16:39, 08AUG
(1224785.050000) Admin login successful by 192.168.1.64 on HTTP (1224766.610000) Admin login FAILED by 192.168.1.64 on HTTP (1224648.050000) New GUIsession from IP 192.168.1.64
(1224466.770000) Device disconnected: Hostname: Unknown-d8:dl:cb:ec:a6:fe
IP: 192.168.1.65 MAC: d8:d1:cb:ec:a6:fe
wlan1: STA d8:d1:cb:ec:a6:fe IEEE 802.11: Client disassociated
(1224362.750000) lease for IP 192.168.1.65 renewed by host Unknown d8:d1:cb:ec:a6:fe (MAC d8:d1:cb:ec:a6:fe).lease duration:1440 min (1224362.750000) Device connected: Hostname:Unknown-d8:d1:cb:ec:a6:feiP:
192.168.1.65 MAC:d8:dl:cb:ec:a6:fe lease time: 1440 min. link rate:90.0 Mbps
(1224362.690000) Lease requested
wlan1: STA d8:d1:cb:ec:a6:fe IEEE 802.11:Client associated
(1224241.150000) lease for IP 192.168.1.64 renewed by host FAMILY (MAC
00:13:02:de:6d:e6). Lease duration:1440 min
(1224241.150000) Device connected: Hostname: FAMii.Y IP:192.168.1.64 MAC:
00:13:02:de:6d:e6 Lease time: 1440 min. link rate: 54.0 Mbps
(1224241.090Cl00) Lease requested
wlan1TA 00:13:02:de:6d:e6 IEEE 802.11:Client associated
OUT: BLOCK [9] Packet invalid in connection (TCP
192.168.1.66:34905->31.13.72.38:443 on ppp1)
(1223644.770000) Device disconnected: Hostname: Unknown-d8:dl:cb:ec:a6:fe
IP: 192.168.1.65 MAC: d8:d1:cb:ec:a6:fe
wlanl: STA d8:d1:cb:ec:a6:-fe IEEE 802.11:CHent diSassociated
(1223489.390000) Lease for IP 192.168.1.65 renewed by host Unknown d8:d1:cb:ec:a6:fe (MAC d8:d1:cb:ec:a6:fe).lease duration:1440 min (1223489.380000) Device connected:Hostname:Unknown-d8:dl:cb:ec:a6:fe IP:
192.168.1.65 MAC: d kd1:cb ec:-a6-:fe Lease time: 1440 min. Link rare: 90.0 Mbps
(1223489.330000) Lease requested
wlan1: STA d8:d1:cb:ec:a6:fe IEEE 802.11: Client associated wlan1TA d8:d1:cb:ec:a6:fe IEEE 802.11: Client disasSociated
wlan1TA d8:d1:cb:ec:a6:fe IEEE 802.11:Client associated
OUT;BLOCK [9] Packet i valid in connection (TCP
192.168.1.66:34375->31.13.72.38:443 on pppl)
l'N':BLOCK [16-} Remote administration {ICMP type 8 code 0
117.1.42.94->86.182.228.205 on ppp1)
IN: BLOCK [9] Packet invalid in connection (TCP
31.13.72.33:443->86.182.228.205:44156 on ppp1) IN: BLOCK [9] Packet invalid in connection (TCP
31.13.72.33:443->86.182.228.205:36615 on ppp1)
OUT: BLOCK [9] Packet invalid in connection (TCP
192.1-68.1.68:49476->173.252.103.16:443 OR ppp1)
BLOCKED 5 more packets (because of Packet invalid in connection) OUT: BLOCK [9] Packet invalid in connection (TCP
192.168.1.68:49443->95.100.195.205:443 on ppp1)
OUT:BLOCK {9] PaCket invalid in connection (TCP
192.168.1.68:49438->95.100.194.217:443 on ppp1)
IN:BLOCK [9] Packet invalid in connection (TCP
95.100.194.217:443->86.182.228.205:49444 on ppp1)
(1222111.810000) Lease for IP 192.168.1.68 renewed by host Unknown-
70:56:81:46:bf:d9 (MAC 70:56:81:46:bf:d9).Lease duration:1440 min
(1222111.810000) Device connected:Hostname:Unknown-70:56:81:46:bf:d9 IP:,
192.168.1.68 MAC:70:56:8:t:46:bf:d9lease time:1440 min. Link rate:52.0 Mbps
(1222111.750000) Lease requested .-
wlanO: STA 70:56:81:46:bf:d9 IEEE 802.11: Client associated • (1222093.690000) Device dlsconn: Hostname:Unknown-
00:25:00:b7:35:f6-2 IP: 192.168. MAC: 00:25:00:b7:35:f6 wlanoTA 00:25:00:b7:35:f6 IEEE 802.11:Client disassociated
OUT:BLOCK [9] Packet invalid in connection (TCP
192.168.1.66-:43272->31.13.72.33:443 on ppp1)
221969.130000) lease for IP 192.168.1.67 renewed by host Unknown-
00:25:00:b7:35:f6-2 (MAC 00:25:00:b7:35:f6). lease duration:1440 min
(1221969.130000} Devicconnected: Hostname·:Unknowwoo·:25:00:b7 35:f6-2
IP: 192.168.1.67 MAC: 00:25:00:b7:35:f6 Lease time: 1440 min. Unk rate: 54.0
Mbps
(1221969.070000) Lease requested
wlanO: STA 00:25:00:b7:35:f6 IEEE 802.11:Client associated
(1220365.290000) Device disconnected: Hostname:Unknown-
00:25:00:b7:35:f6-2 IP: 192.168.1.67 MAC: 00:25:00:b7:35:f6 wlanOTA 00:25:00:b7:35:f6 IEEE 802.11:Client disassociated
(1220348.230000) Lease for IP 192.168.1.67 renewed by host Unlmown-
00:25:00:b7:35:f6-2 (MAC 00:25:00:b7:35:f6).lease duration: 1440 min
(1220348.230000) Device connected: Hostname:Unknown-00:25:00:b7:35:f6-2
IP: 192.168.1.67 MAC: 00:25:00:b7:35:f6 Lease time: 1440 min. Unk rate: 54.0
Mbps
(1220348.170000) lease requested
wlanOTA 00:25:00:b7:35:f6 IEEE 802.11:Client associated
IN: BLOCK f16] Remote administration (TCP
123.151.42.61:12233->86.182.228.205:8080 on ppp1) OUT: BLOCK [9] Packet invalid in connection (TCP
:t92.Hi8.1.66:53813->31.13.72.33:443 on ppp1)
OUT:BLOCK [9] Packet invalid in connection (TCP
192.168.1.66:43989->31.13.72.33:443 on ppp1)
IN: BLOCK [16] Remote administration (ICMP type 8 rode 0
2.7.251.109.227->86.182.228.205 on pppl)
(1216770.650000) Device disconnected:Hostname:Unknown-
00:25:00:b7:35:f6-2 IP: 192.168.1.67 MAC: 00:25:00:b7:35:f6
OUT:BLOCK [9j Packet invalid in connection (TCF
192.168.1.67:49180->74.125.136.109:993 on ppp1)
wlanOTA 00:25:00:b7:35:f6 IEEE 802.11:Client disassociated
(1216753.280000) Lease for IP 192.168.1.67 renewed by host Unknown-
00:25:00:b7:35:f6-2 (MAC 00:25:00:b7:35:f6). lease duration:1440 min
(1216753.270000) Device connected: Hostname: Unknown-00:25:00:b7:35:f6-2
IP: 192.168.1.67 MAC: 00:25.:00-:.b7.:35:f6 Lease time: 1440 min. Unk rate: 54.0
Mbps
(1216753.220000) lease requested
wlanO: STA 00:25:00:b7:35:f6 IEEE 802.11:Client assodat
OUT: BLOCK [9] Packet invalid in connection (TCP
192.168.1.66:55944->23.21.78.229:443 on ppp1)
OUT: BLOCK [9J Packet invafid in connection (TCP
192.168.1.66:34794->31.13.72.33:443 on ppp1)
OUT:BLOCK [9] Packet invalid in connection (TCP
192.168.1.66:41441->31.13.72.33:443 on ppp1)
{1213176.020000) Device disconnected:.Hostname:Unknown-
00:25:00:b7:35:f6-2 IP: 192.168.1.67 MAC:00:25:00:b7:35:f6 wlanO: STA 00:25:00:b7:35:f6 IEEE 802.11: Client disassociated
(1213158.410000) Lease for IP 192.168.1.67 renewed by host Unknown-
00:25:00:b7:35:f6-2 (MAC 00:25:00:b7:35:f6). lease duration:1440 min _./:\ (1213158.400000) Device connected:Hostname:Unknown-00:25:00:b7:35:ftt.Y IP: 192.168.1.67 MAC: 00:25:00:b7:35:f6 Lease time: 1440 min.Unk rate: 54.0
Mbps
(1213158.340000) Lease requested
wlanO: STA 00:25:00:b7:35:f6 IEEE 802.11: Client associated
OUT:BLOCK (9] Packet invalid in connection (TCP
192.168.1.66:59767->176.34.180.243:443 on ppp1) OUT;BLOCK [9] P.acket invalid in connection {TCP
192.168.1.66:56075->31.13.72.33:443 on ppp1) OUT: BLOCK [9] Packet invalid in connection (TCP
192.168.1.66 581:1:0->31.13.72.33:443 on ppp1)
BL.OCKED 2 more packets (because of Packet invalid in connection) OUT:BLOCK [9] Packet invalid in connection (TCP
192.168.1.66:56251->31.13.72.33:443 on ppp1)
OUT:BLOCK [9] Packet invalid in connection (TCP
192.168.1.66:36959->31.13.72.33:443 on ppp1)
BlOCKED 1more packets (because of Packet invalid in connection)

It could be that the Ipod touch is having problems with both the 2.4GHz and 5GHz frequencies being named the same. If you give them separate SSids it may help. ie add a 5 to the 5GHz SSid.
If you do this you will need to re-connect all your devices that can see both frequencies to both SSids so that they will swap between the frequencies seamlessly when ever they need to
See link how to change SSid.
http://bt.custhelp.com/app/answers/detail/a_id/44504/related/1/session/L2F2LzEvdGltZS8xMzc1OTY2ODIxL...
Once you have changed the SSid I would delete the network connection on the Ipod touch and start again.

Homehub 3.0 Wireless Event Log messages

Similar Messages

Maybe you are looking for