I have an error to configure the PCI 4451 (Function DAQ_Op)

The NI DAQ 7.3, Labview 6i, Labview 7.1 and PCI 4451 was instaled in my computer.
I did an application named "PCI4451_Leitura_call.vi" in Labview 7.1 to access the board but a error occurred.
I called nidaq32.dll in LabVIEW and selected the function AI_Change_Parameter. Its works, but the function DAQ_Op isn't. The message below was showed.
Message:
LabVIEW: An exception occurred within the external code called by a Call Library Node. This might have corrupted LabVIEW's memory. Save any work to a new location and restart LabVIEW.
VI " PCI4451_Leitura_call.vi" was stopped at Call Library Function Node 0x2D28 of subVI "PCI4451_Leitura_call.vi"
Can you help me?

Hi PCI 5411,
The problem is due to incorrect default setting of some of the parameters for Daq_op function. Please refer to this knowledge base (kb) for more info about this issue. Also, try running the example code attached to the KB and see if you can replicate the problem or isolate where the error occurs.
I hope this helps.
Regards,
Natasa

Similar Messages

I have found a person who has a driver software to connect Labview with PCI card. But he says that i need to download a freeware software to configure the PCI card. But you have mentioned that freeware is for GPIB boards. Is it correct ??

I have found a person who has a driver software to connect Labview with a general PCI card. But he says that i need to download a freeware software from NI website to configure the PCI card. But you have mentioned that freeware is for GPIB boards. Is it correct ?? Is there any other way out ??

I would ask the person who told you about the freeware software to help you find exactly where it is. I am not aware of any freeware software for configuring motion PCI cards but maybe the person you know might be able to help you locate it.

Windows 8.1 Hyper-V - Error while configuring the hard disk 0xC03A0014

Hello. I have just enabled Hyper-V on my Windows 8.1 laptop.
Dell Latitude E7440 i7-4600U @ 2.10GHz
I can create a Virtual-Switch but I am unable to create a new Hard Disk or Virtual Machine within Hyper-V. I get the same error for both processes.
Error: The Virtual Machine Management Service encountered an error while configuring the hard disk on virtual machine New Virtual Machine.
Failed to create the virtual hard disk.
The system failed to create C:\Users\user\Documents\Test\New.vhdx .
Failed to create the virtual hard disk
The system failed to create C:\Users\user\Documents\Test\New.vhdx . A Virtual disk support provider for the specified file was not found. (0xC03A0014).
I have ran all Dell Client System updates and all of windows updates.
I have attempted to create a virtual machine on the current SSD and also an external drive. The same error appears.
I have also attempted to create a virtual hard disk via Hyper-v with a Base vhdx, still the same error occurs. I've tested the base image on other laptops of the same model and windows 8.1 without issue.
Any thoughts on how I can fix this?
Thank you,
-Jake

Hi Jake,
"Enable Data Execution Protection (DEP) in the BIOS and make sure the Format of drive file system is not fat32.
1. Uninstall Intel Active System Monitor 3.0, if installed.
2. Disable "Intel IPMI Service" and "Intel Monitoring Agent" Service.
3. Open regedit and locate: HKLM\System\CurrentControlSet\Services\imbdrv.
4. Change the Start Key to 4 (Disabled).
5. Locate HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\{4D36E97D-E325-11CE-BFC1-0 8002BE10318}.
6. Take ownership of the ‘Properties’ key.
7. Give yourself full permission for this key.
8. Now locate the properties key; if you see a ‘Security’ entry there, that is your problem. Delete this key.
9. Try attaching or adding the VHD again after rebooting.
If above steps did not help, add the Network Service account to Local Administrator group."
It is quoted from the similar thread below :
http://social.technet.microsoft.com/Forums/windows/en-US/55085ff3-0f26-41bd-b590-bb3490e2d6f5/win-7-professional-a-virtual-disk-support-provider-for-the-specified-file-was-not-found?forum=w7itprovirt
Hope it helps
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Hyper-V encountered an error while Configuring the network on Vmachine

Hi all,
i am novice in window server 201, I learning from a ebook.While i doing the step of creating virtual machine , i got this error
Hyper-V encountered an error while configuring the network on Vmachine
Hyper-V encountered an error trying to access an object on computer 'localhost' because the object was not found. The object might have been deleted, or you might not have permission to perform the task. Verify that the virtual Machine Management service
on the computer is running. If the service is running,try to perform the task again by using Run as Administrator

Windows Server 201? Are you sure?
What sort of machine are you trying to install and run Hyper-V on? What OS is it running?
Bill

HT1926 I have an error installing itunes : the installer has insufficient privilidges to modify this file C:/ program files\itunes \ipod updater\ext.dlll? what to do?

I have an error installing itunes : the installer has insufficient privilidges to modify this file C:\program files\itunes \ipod updater\ext.dlll? what to do?

iPhone - not enough access privileges: Apple Support Communities
ITunes Access Privileges Error?!?!: Apple Support Communities
The installer has insufficient ...: Apple Support Communities

Setup synchronize with address for Sage ACT! showed Runtime Error: Cannot configure the section.

Hello Blackberry Senbai...
As my problem showed as subject line. "When I setup synchronize with address book for Sage ACT! showed Runtime Error: Cannot configure the section."
Setup was stopped from this point.
my system info..
Desktop Manager version is 5.0 downloaded from Blackberry website.
ACT version is 2010.
OS: Window XP Pro with service pack 3
Thank you for your time to review my problem.

Hi and Welcome to the Forums!
Since the version of ACT that you state is not contained in the PIM compatibility matrix, I'm not sure that there is anything to be offerred...
KB12268 Applications supported by BlackBerry Desktop Manager for synchronization
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

How can I use the PCI-4451 installed in a laptop?

I would like to configure a sound level meter using a laptop and PCI-4451. I need a portable and rugged system to be used in the field. What are my options? Can I use the Configurable Signal Conditioning Enclosure CA-1000?
Thanks again.

Hello,
The CA-1000 does not contain a PCI bus interface for cards like the PCI-4451. The CA-1000 accepts a variety of signal conditioning modules and is then connected by cable to an acquisition device.
To use the 4451 with a laptop, you would need a Cardbus to PCI expansion chassis, such as those offered by MAGMA and other companies. I mention MAGMA only because I have a small amount of experience with their products. I'm sure there are others that are equally suitable.
If you're not 100% attached to the 4451, there are a couple other options. You could use a 1394 based DAQ device such as the NI DAQPad-6052E for FireWire, which could then be co
nnected to something like the CA-1000 if necessary, depending on your signal specs. Keep in mind that even though both the 4451 and 6052E are nominally 16-bit boards, the 4451 would be more suitable for audio measurements, particularly if you need simultaneous measurements on more than one channel.
Finally, a portable PXI system with the 4472 would make an ideal platform for precision audio measurements, if this fits within your budget and your definition of portable.
Regards,
Brent R.
Applications Engineer
National Instruments

Error While Configuring the Shared Service with Active Directory

Hi All,
I am getting a error while configuring MSAD with Shared Service, when entering the User Id and password and clicking next, the following error is displayed:
"EPMCSS-05180:Failed to validate Security configuration. Failed to connect. Invalid values for Base DN, User DN or Password. Enter valid value(s). Root Cause : [LDAP: error code 49 - 80090308: LdapErr: DSID-0C0903A9, comment: AcceptSecurityContext error, data 52e, v1db1]"
The AD user has the read access to the all users and group in Active Directory. If I use an Active Directory user with Admin privilege, It is getting connected.
But client is not ready to provide the Admin Access due to their internal policy and I also don't have any document which says admin privilege is required. According to the document,the user should have the following privileges only.
"The distinguished name of the user that Shared Services should use to bind with the user directory. This user must have search privilege on the RDN attribute within the DN. For example, in the dn: cn=John Doe, ou=people, dc=myCompany, dc=com, the bind user should have search access to the cn attribute.Special characters in User DN must be specified using escape characters. See “Using Special Characters” on page 46 for restrictions.
Example: cn=admin,dc=myCompany,dc=com
But I am getting confused with the statement "This user must have search privilege on the RDN attribute within the DN". Is it not search privillege?
Can anybody help me with required privilege for Active Directory user to configure with Shared Service.
Thanks in Advance,
Sunil

Thank you All,
i tried connecting using AD Browser from Microsoft, and it went in properly. then i found out that the AD Team here were giving a Wrong Credentials to connect, they Gave me HYP_OID which infact turned out to be a Principal name instead of a 'cn'.
after searching in the AD Browser i found the correct cn which is "Hyperion OID", then it went to the second Screen where now i am trying to search for the Users based on thier Job Nature.
Thank you for all the Support Guys, you both "Celvin" and "John" are the Top Guys under my Search list for any technical Assistance.
Thank you once again Friends....
Regards,
Sunil...
Shantan....

Error in "Configure the Role of the Integration Service",pls,help me :-(

Hi Guru:
When i run the Template Installer,I got the following error in the step 19:"Configure the Role of the Integration Service"
===================================================
Element 'SXMB_SET_ROLE_TO_IS':ONLY_ONE_CENTRAL_XMB
Element 'SAPDEMO.E01.Backend.Unclassified':!AbapConfigurationWriter.FM_CALL!SXMB_SET_ROLE_TO_IS!AbapConfigurationWriter.FAILED!
===================================================
What can i do whit this error?are there anyone who encountered this problem so far?
Best regards
alex zhang

Hi,
Are you installing temp. Installer with Admin user id, make sure this user should have all necessary roles for installations. Check and try to login in SDM.
THanks
Amit lal
Reward points if answer suits your requirement.

Error in Configuring the EBS Adapter for WebCenter

Hi All,
when I'm configuring EBS Adapter for Web Center I'm getting the below Error while running the sql script AXF_EBS_SOLUTION_DATA.sql ,and I check the AXF_CONFIGS table is not available in db schema, not sure when this table will create. please find the error log detail below and give me some hint or link to overcome from this issue.
Error Log:
SQL> @AXF_EBS_SOLUTION_DATA.sql
49 /
v_formId AXF_CONFIGS.FORMID%TYPE;
ERROR at line 2:
ORA-06550: line 2, column 12:
PLS-00201: identifier 'AXF_CONFIGS.FORMID' must be declared
ORA-06550: line 2, column 12:
PL/SQL: Item ignored
ORA-06550: line 3, column 26:
PLS-00302: component 'EVENTID' must be declared
ORA-06550: line 3, column 13:
PL/SQL: Item ignored
ORA-06550: line 6, column 8:
PL/SQL: ORA-02289: sequence does not exist
ORA-06550: line 6, column 1:
PL/SQL: SQL Statement ignored
ORA-06550: line 7, column 13:
PL/SQL: ORA-00942: table or view does not exist
ORA-06550: line 7, column 1:
PL/SQL: SQL Statement ignored
ORA-06550: line 9, column 8:
PL/SQL: ORA-02289: sequence does not exist
ORA-06550: line 9, column 1:
PL/SQL: SQL Statement ignored
ORA-06550: line 10, column 254:
PLS-00320: the declaration of the type of this expression is incomplete or
malformed
ORA-06550: line 10, column 254:
PL/SQL: ORA-00904: "V_FORMID": invalid identifier
ORA-06550: line 10, column 1:
PL/SQL: SQL Statement ignored
ORA-06550: line 11, column 13:
PL/SQL: ORA-00942: table or view does not exist
ORA-06550: line 11, column 1:
PL/SQL: SQL Statement ignored
ORA-06550: line 13, column 8:
PL/SQL: ORA-02289: sequence does not exist
ORA-06550: line 13, column 1:
PL/SQL: SQL Statement ignored
ORA-06550: line 14, column 254:
PLS-00320: the declaration of the type of this expression is incomplete or
malformed
ORA-06550: line 14, column 254:
PL/SQL: ORA-00904: "V_FORMID": invalid identifier
ORA-06550: line 14, column 1:
PL/SQL: SQL Statement ignored
Thanks in advance
Sanjeev

Hi Sanjeev,
You need to check if you have access to AXF_CONFIGS table. Check if you have ran GRANT_ACCESS.sql script which has below grant commands.
grant execute any type to apps;
grant create type to AXF;
grant select on AXF.AXF_CONFIGS to apps;
v_formId AXF_CONFIGS.FORMID%TYPE; means tableName.columnName%type;
so looks like when you are running AXF_EBS_SOLUTION_DATA.sql you are not able to access AXF_CONFIGS table.
Hope this helps.
Regards,
Amol Gavali.

Error while configuring the domain "Configure JDBC Component Schema"

Hi Everyone,
I have installed SOA Suite 11g on my Win 7 machine 64bit OS and while trying to configure the domain for the WebLogic Server. I fallowed the wizard and everything went well till the JDBC Component Schema window. Here I am able to pass through
1. BAM Schema- Failed
2. SOA Infrastructure-Failed
3. User Messaging Service-Passed
4. OWSM MDS Schema-Passed
5. SOA MDS Schema-Passed
and here is the error that i am facing...
Component Schema=BAM Schema
Driver=oracle.jdbc.OracleDriver
URL=jdbc:oracle:thin:@localhost:1521/XE
User=DEV_ORABAM
Password=*******
SQL Test=select 1 from schema_version_registry where owner=(select user from dual) and mr_type='BAM' and version='11.1.1.2.0'
CFGFWK-60850: Test Failed!
CFGFWK-60853: A connection was established to the database but no rows were returned from the test SQL statement.
Component Schema=SOA Infrastructure
Driver=oracle.jdbc.xa.client.OracleXADataSource
URL=jdbc:oracle:thin:@localhost:1521/XE
User=DEV_SOAINFRA
Password=*******
SQL Test=select 1 from schema_version_registry where owner=(select user from dual) and mr_type='SOAINFRA' and version='11.1.1.2.0'
CFGFWK-60850: Test Failed!
CFGFWK-60853: A connection was established to the database but no rows were returned from the test SQL statement.
I googled the error and tried to check whether the Schema_version_registry has any rows are not and initially i don't have any and then I have created table named "Schema_version_registry" and then inserted the values accordingly..
CREATE TABLE schema_version_registry(owner VARCHAR2(30), mr_type VARCHAR2(10), version VARCHAR2(50));
INSERT INTO schema_version_registry(owner, mr_type, version) VALUES ('DEV_SOAINFRA','MDS','11.1.1.2.0');
similarly i did for the DEV_ORABAM but there is no use...........
I am struck at this position can any please help me out........... please..
Thanks in advance
Sorry Guys.. I understood my mistake and change the "mr-type" accordingly... it is successful now..
Thanks if anyone tried to answer it.......
Edited by: user10763276 on Oct 10, 2010 5:11 PM

Hi can anyone please help me ...all the jdbc component schema is failing for me while creating domain.
please find the log.
Component Schema=SOA Infrastructure
Driver=oracle.jdbc.xa.client.OracleXADataSource
URL=jdbc:oracle:thin:@localhost:1521/XE
User=sys as sysdba
Password=*********
SQL Test=select 1 from schema_version_registry where owner=(select user from dual) and mr_type='SOAINFRA' and version='11.1.1.5.0'
CFGFWK-60850: Test Failed!
CFGFWK-60853: A connection was established to the database but no rows were returned from the test SQL statement.
Component Schema=User Messaging Service
Driver=oracle.jdbc.OracleDriver
URL=jdbc:oracle:thin:@localhost:1521/XE
User=sys as sysdba
Password=*********
SQL Test=select 1 from schema_version_registry where owner=(select user from dual) and mr_type='ORASDPM' and version='11.1.1.2.0'
CFGFWK-60850: Test Failed!
CFGFWK-60853: A connection was established to the database but no rows were returned from the test SQL statement.
Component Schema=OWSM MDS Schema
Driver=oracle.jdbc.OracleDriver
URL=jdbc:oracle:thin:@localhost:1521/XE
User=sys as sysdba
Password=*********
SQL Test=select 1 from schema_version_registry where
owner=(select user from dual) and mr_type='MDS' and
version='11.1.1.5.0'
CFGFWK-60850: Test Failed!
CFGFWK-60853: A connection was established to the database but no rows were returned from the test SQL statement.
Component Schema=SOA MDS Schema
Driver=oracle.jdbc.OracleDriver
URL=jdbc:oracle:thin:@localhost:1521/XE
User=sys as sysdba
Password=*********
SQL Test=select 1 from schema_version_registry where owner=(select user from dual) and mr_type='MDS' and version='11.1.1.5.0'
CFGFWK-60850: Test Failed!
CFGFWK-60853: A connection was established to the database but no rows were returned from the test SQL statement.
"

Error while configuring the ASM on linux

i am trying to implement ASM of the virtual machine.. i downloaded the ASM libraries and packages and installed them as a "root" user using the following command:
$>rpm -Uvh oracleasm*
after the installtion was done i went to configure the library driver by executing the following command(also as a root user)
$>/etc/init.d/oracleasm configure...
i answered all the question given by the command and then the following error message occured..
This will configure the on-boot properties of the Oracle ASM library
driver. The following questions will determine whether the driver is
loaded on boot and what permissions it will have. The current values
will be shown in brackets ('[]'). Hitting <ENTER> without typing an
answer will keep that current value. Ctrl-C will abort.
Default user to own the driver interface [oracle]:
Default group to own the driver interface [dba]:
Start Oracle ASM library driver on boot (y/n) [y]:
Fix permissions of Oracle ASM disks on boot (y/n) [y]:
Writing Oracle ASM library driver configuration: [ OK ]
Loading module "oracleasm": Unable to load module "oracleasm"
[FAILED]
i don't have much experience with ASM to solve this problem, so if someone can help then i will appreciate it.
NOTE: my platform is
ORACLE10gR2(10.2.0.1)
RHEL 4 update 5.

i have been trying to delete the ASM library driver and install it again but i get this message everytime i do so..,
[root@localhost RPMS]# rpm -ev oracleasm-2.6.9-55.0.0.0.2.EL-2.0.3-2.i686.rpm
error: package oracleasm-2.6.9-55.0.0.0.2.EL-2.0.3-2.i686.rpm is not installed
then i execute the following command to install it and the following appears.
[root@localhost RPMS]# rpm -ivh oracleasm-2.6.9-55.0.0.0.2.EL-2.0.3-2.i686.rpm
warning: oracleasm-2.6.9-55.0.0.0.2.EL-2.0.3-2.i686.rpm: V3 DSA signature: NOKEY, key ID b38a8516
Preparing... ########################################### [100%]
package oracleasm-2.6.9-55.0.0.0.2.EL-2.0.3-2 is already installed
it is really weired,,,
if someone have encountered this scenario then please explain this issue for me.

Error when configuring the MDK Plug-in Information

After configuring the MDK Plug-in in Eclipse, I press "Test Settings" and the Mobile Engine is not started. Three things happen:
1) I receive an error: "Cannot find the file '-classpath' (or one of its components). Make sure the path and filename are correct and that all required libraries are available"
2) I get a message "tools.jar found, Connection to ME successful, Invoking browser was successful"
3) A browser launches with the address http://localhost:4444/me with a "Page cannot be displayed"
I have been able to login to Mobile Engine, and I have had the Tomcat Server running.
At this point, the ME is not pointing to a SAP Server.
Settings were:
ME Installation folder: C:\Program Files\SAPMobileEngine
Java SDK tools.jar file C:\jdk13112\lib\tools.jar
ME Server Name: localhost
ME webapp root: me
ME webapp TCP port: 4444
Command Line to run browser: cmd /C start iexplore
ME Login: brgradst
ME Password: *****
In my environment variables I have
Variable Name: JAVA_HOME
Variable: C:\jdk13112
Variable Name: Path
Variable: %JAVA_HOME%\bin;%PATH%
Variable Name: TOMCAT_HOME
Variable: C:\KILL\tomcat\jakarta-tomcat-3.3.2
The URL of the instructions I was following was: http://localhost:4444/mdk/content/eclipse/eclipsemdkwizardsconfiguration.html
Thanks
Brandon Gradstein
[email protected]
+1 917 699 4699

Hi Brandon,
I'm wondering if your SAP Server realy is running on the 'localhost'? Don't you work on a seperate machine? Try the MDK-config with the server name of your SAP server, e.g.: ME SERVER NAME: sapserver or so (in case you're working on a different machine)
With that your browser should display the page.
Regards

Error in configure the Help

Hello Everybody,
   i have install the ECC 6.0, Now i want to configure the SAP Help using SR13 so please suggest
step by step procedure. I have tried as follows
T.code   : SR13
On HtmlHelpfile tab :
    Variant      SAPHELP
    Platform     WN32
    Area          IWBHELP
    Path            D:\SAPHelp\ECC6\ECC6 Help - Setup\English\HtmlHelp\HTMLHELP\HELP
    Language     EN
    Default        (Selected)
But it rises the error Like that
could not find file "d:\SAPHelp\ECC6\ECC6 Help -setup\English\HTmlHelp\HTML\HELP\e18e5134\1a06084d\e1000000\9b38f83b\frameset.chm
So please suggest me How to solve the same
Thanks

Hi!
Thanks for reply.
Till i am not able to solve the same.
i cant understand what is this error massage
"could not find file "d:\SAPHelp\ECC6\ECC6 Help -setup\English\HTmlHelp\HTML\HELP\e18e5134\1a06084d\e1000000\9b38f83b\frameset.chm"
becuase the path i have given
D:\SAPHelp\ECC6\ECC6 Help - Setup\English\HtmlHelp\HTMLHELP\HELP
in that path contains only only .chm files
Also error message display that check SAPDOCCD.LOG file. when i check the Log file, the contain as follows
Program path =     C:\Program Files\SAP\FrontEnd\sapgui\HTMLHELP\SHH.EXE
SHH version =     7.1.0.5
Command line =     "TYPE=5&SERVER=&PATH=D:\SAPHelp\ECC6\ESetup\English\HtmlHelp\HTMLHELP\HELPDATA\EN\EN&SYSTEM=RIS&_CLASS=IWB_STRUCT&_LOIO=&_SLOIO=e18e51341a06084de10000009b38f83b&LANGUAGE=EN&RELEASE=700&IWB_COUNTRY=&IWB_INDUSTRY=&_SCLASS=IWB_STRUCT&FRAME=X"
Info:          --- Default settings from command line ---
Info:          HelpType=HtmlHelpFile
Info:          HtmlHelpFilePath=D:\SAPHelp\ECC6\ESetup\English\HtmlHelp\HTMLHELP\HELPDATA\EN\EN
Info:          --- Contents of profile "C:/WINDOWS/sapdoccd.ini" ---
Info:          Could not read profile "C:/WINDOWS/sapdoccd.ini"
Info:          --- Contents of profile "C:/Program Files/SAP/FrontEnd/sapgui/sapdoccd.ini" ---
Info:          Could not read profile "C:/Program Files/SAP/FrontEnd/sapgui/sapdoccd.ini"
Info:          --- Contents of profile "C:/Program Files/SAP/FrontEnd/sapdoccd.ini" ---
Info:          Could not read profile "C:/Program Files/SAP/FrontEnd/sapdoccd.ini"
Warning:     Could not read any profile
Info:          --- Starting HtmlHelp ---
Info:          CHM file="D:\SAPHelp\ECC6\ESetup\English\HtmlHelp\HTMLHELP\HELPDATA\EN\EN\e18e5134\1a06084d\e1000000\9b38f83b\frameset.chm"
Info:          HTM file=""
Error:          Could not find file "D:\SAPHelp\ECC6\ESetup\English\HtmlHelp\HTMLHELP\HELPDATA\EN\EN\e18e5134\1a06084d\e1000000\9b38f83b\frameset.chm"
So please suggest me How to solve the same.
Thanks

Error CIM_ERR_FAILED - Configure the integration server for sld

Hi,
I´m running the Configuration Wizard SLD in "PI_00_This wizard will execute Postinstall steps of technical configuration for the PI Usage". In step 33/142 Configure the integration server for sld, I got following error:
Error: CIM_ERR_FAILED: Qualifier MAX(1) violated for property reference SAP_XIIntegrationServerLogicalIdentity.SameElement
Someone help me?
Regards,

The version is 7.0. I skip this step and finished with sucess. No run the step:
PI_00_This wizard will execute Postinstall steps of technical configuration for the PI Usage Cancelled
PI_01_This template checks if the necessary services are started Cancelled
PI_05_This wizard will configure the integration server for sld Incompletely executed
These steps are with the same error.
Error: CIM_ERR_FAILED: Qualifier MAX(1) violated for property reference SAP_XIIntegrationServerLogicalIdentity.SameElement

I have an error to configure the PCI 4451 (Function DAQ_Op)

Similar Messages

Maybe you are looking for