Is it possible to start a task always on a specific day of a week

– I would like one of the task in my project plan to always start on specific day, like filling timesheet has to be necessarily to be started
each Monday only and no other day irrespective of how other tasks are aligned on the project, is it do-able?

Hi,
Please refer to the link which shows step-wise details of how to do this -
http://epmxperts.wordpress.com/2012/10/29/start-a-task-on-a-specific-day-of-a-week-only/
Sapna Shukla

Similar Messages

When trying to work with Agilent 34401A multimeter (serial RS-232 connection), HP34401A Getting Started.vi gives always the message: "Error 1073807369 occurred at Old VISA Open ".

Baud rate and parity are set correctly, RS-232 cable is also connected correctly. My QuickBasic program has no problems to read and write to the Multimeter. It is obviously a software problem: the same error is persistent if I disconnect RS-232 cable.
I downloaded NI-VISA 2.6 for Windows 95/98/NT/ME/2000/XP frorm digital.ni.com and installed it. But it did not help.
Thank you in advance
Best regards
Alexei Soloviev

Hi Steve
I have problems with the 34401A and serial communication. Do you remember
where the error was in the code ?
Thanks
Klaus
wrote in message
news:[email protected]..
> Alexei,
> This may or may not help, I was tasked to do something similar
> recently and found an error in their driver. The GPIB VISA worked
> fine, but when I tried it on serial it played up. There was an errant
> carriage return (or CR/LF I can't remember). GPIB liked one and Serial
> liked the other. It always amuses me that we never have problems with
> Quickbasic!.
> If you want me to dig deeper give me a shout.
>
> Steve Watts
>
> On Thu, 24 Jan 2002 06:16:55 -0800 (PST), "Alexei V. Soloviev"
> wrote:
>
> >When trying
to work with Agilent 34401A multimeter (serial RS-232
> >connection), HP34401A Getting Started.vi gives always the message:
> >"Error 1073807369 occurred at Old VISA Open ".
> >
> >Baud rate and parity are set correctly, RS-232 cable is also connected
> >correctly. My QuickBasic program has no problems to read and write to
> >the Multimeter. It is obviously a software problem: the same error is
> >persistent if I disconnect RS-232 cable.
> > I downloaded NI-VISA 2.6 for Windows 95/98/NT/ME/2000/XP frorm
> > digital.ni.com and installed it. But it did not help.
> >Thank you in advance
> >Best regards
> >Alexei Soloviev
>

I am trying to find out if I can change a setting of the calendar in my iPhone. When I view calendar, in month, I would like to view it with the starting day of the week being Monday, not Sunday. Is it possible to make this change? SS

I am trying to find out if I can change a setting of the calendar in my iPhone.
When I view calendar, in month, I would like to view it with the starting day of the week being Monday, not Sunday. Is it possible to make this change?

Hello SMEvans32
You can use iCloud to share the Calendar, that way she will always be up to date on that particular section of your work calendar. If you want to use iCloud, I would recommend backing up so you have a safe copy of your data.
iCloud: Calendar sharing overview
http://support.apple.com/kb/PH2689
iCloud Setup
http://www.apple.com/icloud/setup/
Thanks for using Apple Support Communities.
Regards,
-Norm G.

Failed to run task sequence. Error occurred while starting the task sequence (0x8007000E)

Hi there
Patch Tuesday yesterday (10th June2014). As always we deploy new patches first to a test collection where Windows 7 updates automatically apply.
Upon trying to rebuild any of the machines in this test collection, we were presented with the following error message:
Failed to run task sequence. Error occurred while starting the task sequence (0x8007000E)
After searching about this, I found this page from Niall Brady, which explained the problem:
http://www.niallbrady.com/2013/05/17/after-selecting-a-task-sequence-in-configuration-manager-2012-sp1-you-receive-threadtoresolveandexecutetasksequence-failed-code0x8007000e-in-smsts-log/
So I removed some of the machines from the test Windows update collection, and as per the advice in the above link, the error was gone and those machines could be built successfully.
So the problem is there were too many many policies downloaded (apps, packages and most of all updates) for the task sequence ram to store, hence the error.
Now...
...I have a question.
The next logical step to my mind is to patch our OS image with all missing patches, so these do not have to be downloaded at build time. Niall mentions this as one of the resolutions to this issue.
However there seems to be some confusion over whether this would actually make a difference.
I read through this link:
http://social.technet.microsoft.com/Forums/en-US/7e597b44-2586-4063-b6d0-cec48a7c11c7/sccm-2012-task-sequence-failure-0x8007000e?forum=configmanagerosd
There's seems to be no consensus on this.
Is SCCM 2012 clever enough to - when the task sequence is first started - to download ONLY the updates (policies) it detects as NOT present in the OS image...
or
Will it simply try to download policies for ALL items deployed to it, whether the updates are present in the OS image or not?
I will be disappointed if SCCM 2012 SP1 CU2 isn't clever enough to only download policies at build time for the apps, packages and updates it detects as needed.
I'd be grateful for some clarity on this.
Regards,
John, Glasgow.

Hi Jason
Thank you for replying, I appreciate it.
1) We currently have 15 or 16 software update groups for Office updates, dating back a month or two. The latest software update group contains all the patches in the previous software update groups plus the patches released on 10th June. Do you recommend
deleting all but the latest software update group?
2) I'm almost reluctant to ask this, but based on what you have advised, is it the case that when the task sequence executes, it will download policies for each update in each software update group regardless of whether it has already downloaded a policy
for an update in a previous software update group? So in effect it's downloading policies (for updates) it has already downloaded?
3) I'm not clear on why there would be no policy for an image; in Niall Brady's informative page on the 8007000E error, he writes the following:
"The reason it has run of space could be due to four possibilites: too many applications, too many Windows updates, too many Task Sequence steps, too many referenced packages'.
Can you shed some light on why there isn't a policy for an image?
Thanks again for replying,
John.

Return Code value using 'starting new task' and 'wait until'

I'm having a minor issue with some return code values in my ABAP.
This is what part of it used to look like before I modified it:
With Code in version 1, the sy-subrc was not always zero, sometimes it would be 4.
That was fine, and my abap would do something based on the non-zero RC.
had a need to implement an RFC timeout, the only way I could see to do it was to use 'starting new task' etc as seen in Version 2.
However, with my changes, sy-subrc is always zero.
The ABAP runs fine but I know that sy-subrc should sometimes be 4, even when it returns within the allotted 60 seconds.
Maybe I've coded it incorrectly.
Can someone point me in the right direction?
#>> Start of VERSION 1
call function 'MY_FUNCTION_MODULE'
       destination RFCDEST
       tables
            orders_list          = t_orders_packet
            apo_orders_list      = t_apo_orders
            apo_resources        = t_apo_resources
       exceptions
            COMMUNICATION_FAILURE    = 1 MESSAGE MSG_TEXT
            SYSTEM_FAILURE           = 2 MESSAGE MSG_TEXT
            NO_ORDERS_SUPPLIED       = 3
            NO_PEGGED_ORDERS_FOUND   = 4
            ORDERID_CONVERSION_ERROR = 5
            OTHERS                   = 6.
if sy-subrc is initial.
* do some stuff as RC was 0
else.
* log non-zero return code etc
endif.
* << End of Version 1

And now Version 2.
I didn't put this into the 1st post as the formatting goes bonkers.
#>> Start of VERSION 2
call function 'MY_FUNCTION_MODULE'
       destination RFCDEST
       starting new task 'taskname'
       performing receive_result on end of task
       tables
            orders_list          = t_orders_packet
            apo_orders_list      = t_apo_orders
            apo_resources        = t_apo_resources
       exceptions
            COMMUNICATION_FAILURE    = 1 MESSAGE MSG_TEXT
            SYSTEM_FAILURE           = 2 MESSAGE MSG_TEXT
            NO_ORDERS_SUPPLIED       = 3
            NO_PEGGED_ORDERS_FOUND   = 4
            ORDERID_CONVERSION_ERROR = 5
            OTHERS                   = 6.
WAIT UNTIL results_received = 'X' UP TO 60 SECONDS.
if sy-subrc is initial.   << Now this is always ZERO
* do some stuff as RC was 0
else.
* log non-zero return code etc
endif.
FORM receive_result USING iv_taskname.
RECEIVE RESULTS FROM FUNCTION 'MY_FUNCTION_MODULE'
       tables
            orders_list          = t_orders_packet
            apo_orders_list      = t_apo_orders
            apo_resources        = t_apo_resources
       exceptions
            COMMUNICATION_FAILURE    = 1 MESSAGE MSG_TEXT
            SYSTEM_FAILURE           = 2 MESSAGE MSG_TEXT
            NO_ORDERS_SUPPLIED       = 3
            NO_PEGGED_ORDERS_FOUND   = 4
            ORDERID_CONVERSION_ERROR = 5
            OTHERS                   = 6.
results_received = 'X'.
endform.                    "receive_result
* < End of Version 2

ESS - ws01000109 - You are not of the possible agents of the task

Hi
When I try to cancel leave using workflow ws01000109 it is raising message
"You are not of the possible agents of the task ".
Can any body tell wheather we have to maintain data in pa30 transaction for this problem.
I have seen so many thread regarding this But I have not got any answer please reply for the same
I have set all tasks as general task only.
Edited by: balaji ramadas on Jun 8, 2009 4:01 PM

Hello,
You would be better off starting your own thread, and I hope that unlike the poster above you will share the result when you find a solution.
Has your task been set to General Task? If not, try that.
regards
Rick Bakker
Hanabi Technology

Webgui - function module starting new task

Hello,
we want to call a function module which opens a new task from a webgui transaction. This webgui transaction is integrated into EP 6.0.
Does anybody know how to handle this matter?
Thanks in advance and best regards,
Petra

Hi Petra,
"call function .... starting new task " creates a new external session for the current login session. This is the same as doing a /o or "system - Create session". Due to technical restrictions in webgui only one external session is possible.
Best regards,
Klaus

Is it possible to start slideshow from current picture?

Hi,
is it possible to start slideshow from current picture?
Slideshow in Aperture always start from first picture in album.
There is possibility to select bunch of images and than start slideshow and slideshow will use only selected pictures but this is not what I want:
I want it to start from photo that I curently viewing in full scree.
I *do not want* to:
1. exit full screen
2. going to browser
3. than selecting rest of photos
4. than hitting shift+S for slideshow
I just want to hit shift+S and to slideshow starts right from picture that I curently looking.
I hope I was clear enought
Thanx in advance!

If you mean on the phone (like J2ME apps on a cellphone) then the answer is no. However, if you can run the application on the server, then of course.. you just need a way to send a request to the server (e.g. a softkey button which makes a call to http://your-server/path/yourApplication) which triggers the application and does god knows what.

COMMUNICATION_FAILURE in CALL FUNCTION STARTING NEW TASK/Background task

Hi friends,
I am trying to use a FM in a Print Program (when user prints a document), using
CALL FUNCTION STARTING NEW TASK 'TASK' DESTINATION 'NONE'.
The program is triggered from VL02N tcode.
But it's giving an exception - COMMUNICATION_FAILURE. Message is Error when opening an RFC connection
I also tried
CALL FUNCTION IN BACKGROUND TASK as Separate Unit
then error message pops up - Database error when recording transactional RFC
We are attaching a PDF file of the print to content server within this function module and because the "attaching" takes a while, this part needs to be detached from the print program so that we can avoid performance issue.
I can't figure out the issue. i gues this is happening because print program is already running in Update task. I also tried with RFC enabled FM. Please help me resolve/understand the issue.
Appreciate your help.
Regards,
Ronjan.

Hi Ronjan,
COMMUNICATION_FAILURE. Message is Error when opening an RFC connection
I guess the reason for the above is that every RFC call synchronous/Asynchronous issues a DB COMMIT and we cannot have DB COMMITs in the V1/V2 updates, please go through the link below.
http://help.sap.com/saphelp_nw70ehp2/helpdata/en/23/e9aa61638e404d81575e939b5cd847/frameset.htm
Now, the possible solutions i can think of are,
1) Call the FM in update task delayed start and try.
2) Or create a report program and use SUBMIT (look at the job options as well).
@Mainak
3. Write a statement COMMIT WORK AND WAIT. This will actually invoke the FM
Mainak, this will lead to a Update termination, as the program is running in an update task.
Regards,
Chen

Starting new task in update task

Hello,
Can we start a new task in update function module.
Say, I want to enhance a standard update function module and call a new function module in it using STARTING NEW TASK,
is it possible to do so?
Because, when I try to do this, i am getting update termination
Please suggest.

check the bellow link
[ http://nafran.blogspot.com/2009/06/only-way-of-parallel-or-multi-threading.html|http://nafran.blogspot.com/2009/06/only-way-of-parallel-or-multi-threading.html]

NOT POSSIBLE TO START ESSBASE WHEN SSO INITIALIZATION FAILS

Version is 11.1.1.3. My Essbase is not starting. Issues from the logs and what I have attempted are as follows. I have highlighted the relevant areas in bold.
When Starting Essbase from products/Essbase/bin/start.bat:
C:\Hyperion\products\Essbase\bin>start.bat
C:\Hyperion\products\Essbase\bin>REM eis
C:\Hyperion\products\Essbase\bin>net start "Hyperion Integration Services"
The requested service has already been started.
More help is available by typing NET HELPMSG 2182.
C:\Hyperion\products\Essbase\bin>REM APS
C:\Hyperion\products\Essbase\bin>call C:\Hyperion\products\Essbase\aps\bin\start.bat
C:\Hyperion\products\Essbase\bin>REM aps
C:\Hyperion\products\Essbase\bin>net start HyS9aps
The requested service has already been started.
More help is available by typing NET HELPMSG 2182.
C:\Hyperion\products\Essbase\bin>REM EAS
C:\Hyperion\products\Essbase\bin>call C:\Hyperion\products\Essbase\eas\bin\start.bat
C:\Hyperion\products\Essbase\bin>REM eas
C:\Hyperion\products\Essbase\bin>net start HyS9eas
The requested service has already been started.
More help is available by typing NET HELPMSG 2182.
C:\Hyperion\products\Essbase\bin>REM EssbaseAgent
C:\Hyperion\products\Essbase\bin>net start hypservice_1
The service name is invalid.
More help is available by typing NET HELPMSG 2185.
C:\Hyperion\products\Essbase\bin>REM EssbaseStudio
C:\Hyperion\products\Essbase\bin>C:\Hyperion\products\Essbase\EssbaseStudio\Server\startServer.bat
C:\Hyperion\products\Essbase\bin>setlocal
C:\Hyperion\products\Essbase\bin>set CONFIGTOOL_HOME="C:\Hyperion\common\config\9.5.0.0"
C:\Hyperion\products\Essbase\bin>call ""C:\Hyperion\common\config\9.5.0.0"\setJavaRuntime.bat"
Logging configuration file is not found. Expected filename is C:\Hyperion\products\Essbase\bin\.\server.properties
Log file location is:
C:\Hyperion\logs\esbstudio\server.log
13:23:09 11/01/11 INFO Starting up
13:23:09 11/01/11 INFO Oracle Essbase Studio Server. Version 11.1.1.3.00, Bui
ld 090, June 25 2009
13:23:16 11/01/11 (system) WARNING Failed to load driver for sap
13:23:16 11/01/11 (system) SEVERE Cannot load Teradata connector
13:23:16 11/01/11 (system) WARNING Failed to load driver for teradata
13:23:16 11/01/11 (system) WARNING Failed to load driver for mysql
13:23:16 11/01/11 (system) WARNING Failed to load driver for netezza
Essbase.log:
[Tue Oct 25 11:26:31 2011]Local/ESSBASE0///Error(1051223)
Single Sign On function call [css_init] failed with error [CSS Error: CSS method invocation error: com.hyperion.css.CSSSystem.<init>]
[Tue Oct 25 11:26:31 2011]Local/ESSBASE0///Info(1051198)
Single Sign-On Initialization Failed !
[Tue Oct 25 11:26:31 2011]Local/ESSBASE0///Info(1051232)
Using English_UnitedStates.Latin1@Binary as the Essbase Locale
[Tue Oct 25 11:26:31 2011]Local/ESSBASE0///Error(1051527)
In Shared Services Security mode it is not possible to start Essbase when single sign on initialization fails.
AND
C:\Hyperion\logs\essbase\SharedServices_Security_Client.log com.hyperion.css.CSSSystem.<init>(Unknown Source)
2011-10-25 11:26:11,039 INFO [main] Configure CSS with registry com.hyperion.css.CSSSystem.initCSSSystem(Unknown Source)
2011-10-25 11:26:11,039 INFO [main] Initializing CSS from Registry. com.hyperion.css.common.configuration.CSSConfigurationManager.getConfiguration(Unknown Source)
2011-10-25 11:26:11,085 INFO [main] Trying to get Registry Instance com.hyperion.css.registry.RegistryManager.<init>(Unknown Source)
2011-10-25 11:26:31,023 ERROR [main] 20:1092:Failed to initialize EPM System registry. *[Root Cause: java.sql.SQLException: [Hyperion][SQLServer JDBC Driver]Error establishing socket to host and port: machinex:1433. Reason: Connection refused: connect ] com.hyperion.css.registry.RegistryManager.<init>(Unknown Source)*
*2011-10-25 11:26:31,023 ERROR [main] Arguments: param1={}, param2=null, param3=C:\Hyperion\logs\essbase\,* com.hyperion.css.CSSSystem.initCSSSystem(Unknown Source)
2011-10-25 11:26:31,023 INFO [main] CSS system intialization failed. : [21484 ms] com.hyperion.css.CSSSystem.initCSSSystem(Unknown Source)
What I have attempted:
- Attempted to connect to Shared Services, Workspace url's - YES
- Checked openLDAP & my Database is running - YES
- Added following to Configuration File :
SharedServicesLocation machinex 28080
AUTHENTICATIONMODULE CSS http://machinex:28080/interop/framework/getCSSConfigFile YES, but same error
- Changed essbase.bak to essbase.sec YES but same error
- netstat -an to check for 1423. Port 1423 is not listening, although ALL TCP Ports have been enabled. So YES but same error.
- Read Knowledgebase article # 954322.1 - the suggested things in there don't seem to apply to my case, unless I am missing something.
At this point does anybody have any suggestions ?

An update: Just for kicks, I tried restarting Essbase using Start->Programs-EPMSystem->Essbase->EssbaseServer->Essbase.bat and apparently now Essbase is started.
EAS, Studio and Planning however are down.
Excerpt from the HyS9eas-sysout.log:
[ERROR] RegistryUtils - SQL Exception when trying to create a new connection [Hyperion][SQLServer JDBC Driver]Error establishing socket to host and port: machinex:1433. Reason: Connection refused: connect
* CRITICAL ERROR: Common Security Services initialization failed. Please *
* make sure that a valid entry is provided for SECURITY_CONFIGURATION in *
* OlapAdmin.properties. This is required if Shared Services is enabled. *
* Please restart the server after the changes. *
Stopping DAO factory!
HBR Configuration has not been initialized. Make sure you have logged in sucessfully and there are no exceptions in the HBR log file.
java.lang.ExceptionInInitializerError
.... bunch of java code.
This is really strange. There is NOTHING that I changed, started or stopped which could have caused Essbase to start magically all of a sudden.
Any insights into the cause of all this ?

Installed Adobe dlm add-on and now Firfox will not open. I see the process starting in Task Manager but no window opens. Unistalled Firefox then re-installed but still no luck. HELP ME!

''Duplicate post, continue here - [https://support.mozilla.com/en-US/questions/793259]''
I installed Adobe dlm add-on and now Firefox will not open. I see the process starting in Task Manager but no window opens. Unistalled Firefox then re-installed but still no luck. HELP ME! I do not want to use IE! I presume it has something to do with Adobe DLM as ever since then it is not working.

I had this problem for a couple weeks as well and it was extremely frustrating considering we use firefox for all our company tasks. Here is the solution:
First of all if you have no bookmarks you want to save, then go directly to step 7. If you want to save your bookmarks first, then follow these steps.
1. Shut down the computer
2. Reboot and open firefox
3. Go to Task Manager, right click firefox.exe, and click END PROCESS TREE
4. WAIT 30 SECONDS! Then Double-click the shortcut to try and open firefox again
5.Repeat steps 3 and 4 until firefox finally opens (trust me, eventually it will)
6. Once it finally opens, backup your bookmarks,
7. Download a copy of firefox from there website
8. Uninstall from programs menu and make sure to check the box REMOVE ALL COMPONENTS
9. install the new copy and BOOM! it works
If it doesn't work, you're an idiot. If you don't want to reinstall firefox, then you're out of luck. Good Luck!

Is it possible to start a MacBookPro in target mode with a MacBookAir?

Is it possible to start a MacBookPro in target mode with a MacBookAir?
I have a MacBookPro and I would like to start it in a target mode using a MacBookAir as a disk cible,
is it possible to do it? Which cale or adapter do I need to do it?

namdev1 wrote:
Is it possible to start a MacBookPro in target mode with a MacBookAir?
Yes, you can use Target Disk Mode with a suitable adapter:
OS X Lion: Transfer files between two computers using target disk mode
To determine the cable you need requires you describe which MacBook Air and MacBook Pro models you have. The latest ones have Thunderbolt ports, for which you can use a Thunderbolt cable. If the MacBook Pro has only a FireWire port, you can use a Thunderbolt to FireWire adapter. Early MacBook Air models have neither.
Search for cables and adapters on Apple's website:
http://store.apple.com/us/product/MD464ZM/A/apple-thunderbolt-to-firewire-adapte r
http://store.apple.com/us/product/MD862ZM/A/apple-thunderbolt-cable-05-m

OSD - Failed to run Task Sequence. An error occurred while starting the task sequence (0x8007000E).

Failed to run Task Sequence.
An error occurred while starting the task sequence (0x8007000E)."
While OSD, picks up task sequence but fails in resolving task sequence dependencies. SMSPXE identifies device is not in database (unknown).
SMSTS.log shows
ThreadToResolveAndExecuteTaskSequence failed. Code(0x8007000E)" in SMSTS.LOG, have seen other articles suggesting failure due to lack of storage (RAM) but this task sequence has worked in past.
By the way, if I create a stand alone media, we are able to image the workstation. What has changed in the task sequence such that the workstation is unable to download policies due to lack of storage (RAM) on workstation. Workstation has 2 GB of RAM.

I have found a work around for the issue, even though the computer is unknown, there were software updates targeted to the ALL SYSTEMS collection which applies to All Unknown Computers and therefore to x64 Unknown Computer and x86 Unknown Computer.
We had a SCEP ADR applying definition updates to All Systems, we applied the ADR to a different collection, removed all the SCEP updates to All Systems and successfully re-imaged the workstation. Following article was of great help in identifying the problem
after-selecting-a-task-sequence-in-configuration-manager-2012-sp1-you-receive-threadtoresolveandexecutetasksequence-failed-code0x8007000e-in-smsts-log
Thanks Gerry for your assistance.

How to call RFC with STARTING NEW TASK...performing my_form... in a class?

Hello,
I created a test report for parallel processing and this works perfectly fine but when I try to build this into a class I somehow cannot create the receiving form inside the method of the class...
method test.
        CALL FUNCTION 'ZZCR_PARALLEL' STARTING NEW TASK lv_index DESTINATION IN GROUP DEFAULT
          PERFORMING transfo_result ON END OF TASK
          EXPORTING
            input_xstring = lx_clause_text.
endmethod.
I tried to place the form before the endmethod but this doesn't work and afterwards is also not an option.
Is ABP OO not supporting parallel processing?
Thanks and regards,
Christoph

Hello Christo ,
                     I am also trying to use the same in OO context . Just in he early stages of collecting information.If you could just tell what you found out in the document it could be opf immense help.
Comradely,
K.Sibi

Is it possible to start a task always on a specific day of a week

Similar Messages

Maybe you are looking for