Issue with WAN Miniport when setting up VPN server in Windows 7

I tried making my computer a VPN server by setting up a "New incoming connection" under network connections within Network and sharing center. Originally, it did complete but did not show any WAN Miniport connections. I could not connect to this VPN
with my other computer.
What I've done so far:
I "updated" all the WAN Miniports in Device Manager to "MAC Bridge Miniport" driver (since I could not uninstall them as they were) and then proceeded to uninstall all the WAN miniports. I rebooted my computer and then the device
drivers tried to install automatically but only a few installed successfully.
I then downloaded the latest WDK (8.1) and tried re-installing all the WAN Miniports via devcon.exe with the command "devcon.exe install c:\windows\inf\netrasa.inf MS_PptpMiniport". It said that the node was created but it failed to install the
drivers. I rebooted my computer but some of these mini ports appeared as "Unknown" in Device Manager while others appeared with their names but with numbers attached since I've attempted this a few times, Ex: "WAN Miniport (IP) #3".
from my understanding, I need at least WAN Miniport pptp to be working for VPN to work. I don't know what to do at this point. Any help is greatly appreciated. Thanks in advance.
Gateway DX4822-01 Desktop PC
Windows 7 64-bit, SP1

Hi,
Please try to use Incoming connection troubleshooter to fix this problem for test. If it identify any problem that couldn't fix this problem, please provide the error message here.
Control Panel\All Control Panel Items\Troubleshooting\All Categories
Roger Lu
TechNet Community Support

Similar Messages

How to get WAN DNS when set up Airport Extreme on Windows

I am trying to set up my home network by using Airport Extreme Base to connect DSL via PPPoE. Here's what I did:
1. Update firmware to latest version: V5.7;
2. Install Airport Setup 4.2;
3. Run Setup Assistant, enter the right DSL account and password by using PPPoE, also setup base name, network name and base password, and DSL service provider's DNS ip, backup DNS ip;
4. Everything gets updated into base station, restarted, local wireless network set up successfully, but can not connect to WAN;
5. Tried ipconfig/all, find DNS is 192.168.1.1;
6. Tried to dial DSL from computer via PPPoE directly, validated account and password is ok, and it is working well to get me to internet.
Can someone here help me solve my issue?
Dell D600 Windows XP Pro

I figure out answer by myself now. I would like to share it with you all here: firmware V5.7 has some major bug causes the problem. When I update my base station with firmware V5.5.1, it works right away.

Issue with Feature Deployment when DB and Web Server are on different machine

Hi,
We are trying to deploy our Custom Processes as site feature.
In Visual studio it shows Deployment Succeeded but feature is not available in Site features.
when we checked “Central Administration -> Manage Farm Solution” it shows below error.
Web Server : The solution was successfully deployed.
DB Server IP : Elements of type 'Receivers' are not supported at the 'Farm' scope. This feature could not be installed.
DB Server IP : Elements of type 'Receivers' are not supported at the 'Farm' scope. This feature could not be installed.
We are able to ping DB server from Web Server .
Also , we are able to add custom fields and lookup manually in web Server and those are getting reflected in DB .
Thanks,
Abhijit

Hello,
I would probably post this in the SharePoint forum as deploying features is a SharePoint process and not Project / Project Server (even if the feature is related to Project Server).
Paul
Paul Mather | Twitter |
http://pwmather.wordpress.com | CPS |
MVP | Downloads

Issue with paper type when remote printing

Hello
we have an issue with printing from redirected printer
on the local machine Windows 8.1 i have a printer installed and when i try to print from a remote pc to my installed printer on my local pc the paper type is replaced.
on the local printer it was set to letter but on the remote the redirected printer is set to legal.
i try to switch it to letter but it was not kept it switch back to legal.
any adviced will be good ?
Thanks

Hi,
We may try to test this and will get back to you as soon as we get outcome.
In addition, here is a Print/Fax forum below you may get more insights from print experts:
https://social.technet.microsoft.com/Forums/windowsserver/en-US/home?forum=winserverprint&filter=alltypes&sort=lastpostdesc
Best Regards,
Amy
Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
[email protected]

Issue with Removing the Patch Set Software 9.2.0.8

Hi experts,
I have issue with removing the patch set software 9.2.0.8
I'm working on solaris box recently ugraded to 9.2.0.8 from 9.2.0.7. however i want to downgrade now. I have followed the document 4547809 mentioned. Now the real issue is when i restored the oracle_home (9.2.0.7) and execute sqlplus /nolog here is error message shown
bash-2.05$ sqlplus /nolog
bash: /oracle/test/920_64/bin/sqlplus: No such file or directory
bash-2.05$ lsnrctl
bash: /oracle/test/920_64/bin/lsnrctl: No such file or directory
Please help
thanks in advance

Hi,
Thanks for reply you are right
ls -l /oracle/test/920_64/bin/sqlplus was not exist. However i copied everything from the backup.
I'm trying again
cp -r bk_test_home/* /oracle/test/920_64/*
still i couldn't the file however it exist in bk_test_home. please suggest
Thanks and regards

Issue with Emoji icons when sent from iOS6 to iOS5

Issue with Emoji icons when sent from iOS6 to iOS5, all icons appear as a square on the iOS5 message screen.
Both iOS are the current version and the phones are 4S 64GB
Anybody got this problem

Hi!
What kind of RFC do you use? If you use synchronous RFC the caller waits for the answer/result of the called function. In normal cases this should solve your issue.
Regards,
Volker

Hi BC, I have an issue with BC. When the shopping cart is used it takes stock out of inventory and h

Hi BC,
I have an issue with BC. When the shopping cart is used it takes stock out of inventory and holds it, regardless of whether or not a customer proceeds to purchase. OK.
To make matters worse, the stock is only cleared from the shopping cart when the customer closes the browser - not when they close the shopping window.
Now lets say a customer doesn't close their browser for a month - it happens! .. when their stock is finally returned it may throw out our stock levels that have in the meanwhile been adjusted. So their stock will be added on top of an accurate stock take, putting stock in that isnt really available.
This is causing us mayhem.
We have not yet seen if stock is actually returned at all. In the test we did today where we filled a shopping cart then closed the browser without making a purchase, the stock was not returned immediately. So we dont even know when it will be returned - thats IF a customer actually closes their browser. Any solutions out there?
Jo

Hi there,
The way stock is managed in this situation is desirable for many in that case otherwise shopping on a site and adding to cart would not be viable or use friendly.
What you mention about not closing a browser though is a case that is not true. IF you go into the shop settings in the admin you can see the cart restore timer which is by default 24 hours but you can change this to as low as 1 hour if you wish.

I have problem with my ipad when set up ipad asked to activation but i cant remember my apple id that i used to setup.now i can not open it .Is there any way to fix this problem?

I have problem with my ipad when set up ipad asked to activation but i cant remember my apple id that i used to setup.now i can not open it .Is there any way to fix this problem?

Hello Abdo_Zain,
I would be concerned too if I was not able to gain access to my iPad. If you are unsure what your Apple ID is, you can find the steps in this article:
Apple ID: How to find your Apple ID
http://support.apple.com/kb/HT5625
You can reset a forgotten Apple ID password by going to the following link:
Apple - iForgot
https://iforgot.apple.com
Also, you may be able to skip the step of entering your Apple ID if you are setting up the iPad for the first time.
Thank you for using Apple Support Communities.
Best,
Sheila M.

Issue with BAPI_ACC_***_TRANSFER_POST (when trying to execute as per ABT1N)

Hello experts,
For this thread, please check the following link:
[Issue with BAPI_ACC_***_TRANSFER_POST (when trying to execute as per ABT1N);
Thanks and Regards,
Daniel.

Hi Experts,
The question has been answered as per the following "link":
[Issue with BAPI_ACC_***_TRANSFER_POST (when trying to execute as per ABT1N);
Daniel

I have an issue with speaker/microphone. when i call or i recive a call the person on the other side can not hear me.

i have an issue with speaker/microphone. when i call or i recive a call the person on the other side can not hear me.

Hello aalapdesai112,
Lets see if we can get you back to taking calls normally again. Start your troubleshooting with the article below and go through checking to making sure that you are up to date with your iOS as well as a simple restart on your iPhone.
If your voice is too faint or sounds unclear using iPhone, or iPod touch
http://support.apple.com/en-us/HT203792
Regards,
-Norm G.

Setting up VPN Server fails in Windows 8.1

Hello Folks
I'm trying to set up VPN server in my Windows 8.1 box to receive incoming connections. It fails at the last step (http://www.diaryofaninja.com/blog/2012/09/11/setting-up-a-vpn-server-on-windows-7-or-windows-8-ndash-secure-your-internet-use-while-away)
of the process (Allow Access) with the following error. I binged a lot but none of the trouble shooting mechanisms worked for me. I made sure that concerned service (Routing and Remote Access) can be started and stopped manually. Also, the same step works
in Windows 7.
Please see attached for error details.
Highly appreciate any help for fixing the issue.
Cheers
Manohar

Hi Manooh,
Besides disabling IP v6, try reset the TCP/IP in the way below:
Open the command line windows as an administrator and type the command “nets hint ip reset” hit enter, or you can try the fix it below:
http://support.microsoft.com/kb/299357
We usually modify the default RDP port 3389 to another value, if you followed this too, you should add an port exception through a firewall in the way below:
1.Open Windows Firewall
2.In the left pane, click Advanced settings.
3.In the Windows Firewall with Advanced Security dialog box, in the left pane, click Inbound Rules, and then, in the right pane, click New Rule.
4. Choose “port” and input the port number as allowed to connect.
Regards
Wade Liu
TechNet Community Support

W530 Wifi issues and WAN Miniport disabled (Code 31) AHHHH!!!!!!

Hey guys,
This is my 2nd W530. The first one was replaced for the same issues I'm having now.
My wifi is very slow and inconsistent. I'm always having to disconnect and re-connect with my router (brand new router since I thought the old one could be the issue). This has been an issue since I received my new unit.
Yesterday I had a yellow exclamation mark pop up in Lenovo manager and said my network monitor WAN miniport was disabled (code 31). Since that popped up connecting to the wifi is very rare and requires a lot of effort. I'm out of ideas and considering calling Lenovo and having them take this thing back and give me a refund.
Anyone else experienced these issues? I tried windows 8 troubleshooter and it detects the issue but can't fix it. I tried updating the driver and it tells me its up to date and I tried uninstalling it and I'm unable to.

Thanks for that, it's actually exactly what I wanted to read
Again, which WLAN adapter do you have in the system please?
When I read your post yesterday I took a look in my device manager and it was showing exactly the same problem which hadn't been present two days ago. It's something I've been keeping an eye on because I have the Intel Centrino Advanced N-6205 WLAN card which seems to be having problems being reported all over the web.
Trouble shooting to date,
after rolling back my Windows 8 X64 to the 15th May, before running Windows Updates, the WAN miniport problem had gone away. I then started trying to narrow things down by installing / uninstalling various updates and drivers.
At the moment I am at the stage that I can roll back the system to the 15th May, (no problem), and then install through Windows Update "Update for Windows 8 for x64-based Systems (KB2836988)" on it's own and immediately after a restart the WAN miniport problem is there again.
I have as yet been unable to get rid of the error by uninstalling the update, uninstalling / reinstalling drivers and various other softwares which could be a factor, but haven't given up yet.
Any chance you could roll back your system to a point where the error wasn't showing in Device Manager and see if you can replicate what I have experienced by just installing the one update?
Edit; for the record I am using a T430 W8 x64.
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

Issue with instant ringback when using sip trunk to SP

Hi all,
We use CUCM 8.0.2.
We have a SIP trunk to a SP connected via one of our Cisco 2911 routers configured as a CUBE.
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M3, RELEASE SOFTWARE (fc2)
c2900-universalk9-mz.SPA.150-1.M3.bin
Cisco CISCO2911/K9 (revision 1.0)
Technology Package License Information for Module:'c2900'
Technology Technology-package
                  Current       Type
ipbase        ipbasek9      Permanent
security      securityk9    Permanent
uc              uck9            Permanent
data           None            None
We also have several ISDN lines that run out via various Cisco routers configured as H323 gateways.
We use 7945 and CIPC for our phones.
We're having an issue with calls going via the SIP trunk where we hear ringing instantly after dialling - but before the actual device at the other end starts ringing (considerable difference).
Using the SIP trunk: If I make a call to my mobile phone - I hear ringing instantly - about 3 rings before my mobile phone actually starts ringing - undesireable.
Using H323 gateway: If I make a call to my mobile phone - I hear silence for a bit - then ringing when the mobile starts ringing - desired.
Using SIP trunk: If I make a call to a landline that is ready - it rings instantly for at least 1 ring - before the actual phone I'm calling starts ringing - undesireable.
Using H323 gateway: There is a momentary pause before hearing ringing on my phone and the phone I dialled - desired.
Using SIP trunk: If I make a call to a landline that is off-hook (with no call-waiting/etc.) - it rings once and then returns the busy signal (the worst issue) - undesireable.
Using H323 gateway: There is a momentary pause before hearing busy signal - desired.
Phone to phone internally (same network): Operates as expected (instantly rings locally and on the phone I'm calling). Between phones that utilise the SIP trunk and phones that utilise the H323 gateways within the same network - communication is instant and as expected.
Any ideas why this happens and how to stop it?
I want it to not ring until the situation is known and that it can provide the appropriate feedback (ringing/busy/etc.).
Some possibly relevant config (note that there is a known bug with this IOS that meant I had to declare the codec in each dial-peer as the voice class would not work):
voice service voip
address-hiding
mode border-element
allow-connections sip to sip
sip
bind control source-interface GigabitEthernet0/0
bind media source-interface GigabitEthernet0/0
header-passing error-passthru
early-offer forced
midcall-signaling passthru
interface GigabitEthernet0/0
ip address x.x.x.x 255.255.255.252
ip access-group acl.SIP-IN in
no ip redirects
no ip unreachables
ip verify unicast reverse-path
ip virtual-reassembly
duplex full
speed 100
no cdp enable
gateway
timer receive-rtp 1200
sip-ua
connection-reuse
gatekeeper
shutdown
dial-peer voice 1 voip
description *** INBOUND CALLS FROM CARRIER ***
translation-profile incoming SIPTRUNK-INCOMING
session protocol sipv2
incoming called-number #blah blah#
dtmf-relay rtp-nte
codec g711alaw
ip qos dscp cs5 media
no vad
dial-peer voice 61 voip
description **** WA, SA AND NT NUMBERS ****
destination-pattern 0[8]........
session protocol sipv2
session target ipv4:<MY SP's SIP SERVER>
incoming called-number 0[8]........
dtmf-relay rtp-nte
codec g711alaw
ip qos dscp cs5 media
no vad
dial-peer voice 81 voip
description **** MOBILE NUMBERS ****
destination-pattern 0[4]........
session protocol sipv2
session target ipv4:<MY SP's SIP SERVER>
incoming called-number 0[4]........
dtmf-relay rtp-nte
codec g711alaw
ip qos dscp cs5 media
no vad
dial-peer voice 500 voip
description *** INBOUND SIP TRUNK TO CUCM PUB ***
translation-profile outgoing SIPTRUNK-CALLING-ADD-0
preference 1
destination-pattern 5[12]..
session protocol sipv2
session target ipv4:<OUR CUCM PUBLISHER IP>
dtmf-relay rtp-nte
codec g711alaw
ip qos dscp cs5 media
no vad
Any help or a point in the right direction would be greatly appreciated.
Cheers,
Brett

I ended up resolving this issue as follows:
In CUCM, under Device > Device Settings > SIP Profile.
I modifed the profile relevant to my SIP trunk, under the "Trunk Specific Configuration", I set "SIP Rel1XX Options" from "Disabled" to "Send PRACK if 1xx Contains SDP".
Now, I get the expected delay before hearing ringback.
Solved!

Issue with PO Currency when currency changed after the approval.

Hi All,
we have get an issue with PO currency which is as follows
Step1:Created a Limit PO with value 3.701,00 CHF and sent it for approval,,and PO is approved and transfered to backed (We are using "Extended classical scenario' .
Step2:but we got to know that the PO value should be in USD ,so will go to PO and changed the currency value to USD ,it coveted value to 3421 but ,since i need the 3701 USD i changed the value to 3701 at item level and orderd the PO.
but after approval , when it transfered to backed it is showing the value 3.701,00 USD at header level ,but 3.402,84 USD at item level.
so when we are trying to create GR it is populating 3.402,84 USD but we need 3701 USD.
is any one know the what is the problem with this.
please help
Regards
cb

You can re-output a message that has already been outputted (printed or transmitted).
"Repeat message" function
You use this function if you wish to print out or transmit again a complete purchasing document that has already been outputted. Note that the system takes account in the message of any changes made to the purchasing document since it was last outputted - i.e. the system always outputs the current status of the document. If you wish to have old statuses available, you must optically archive the purchasing document.
Activities
You invoke the Messages screen as follows:
Via the purchasing document itself (Header Messages) or
Via <Purchasing document> Messages Print/transmit.
Enter the processing status 1 (successfully processed) and display the messages.
Select the desired message and choose Goto-> Message details.
Choose Edit-> Repeat message or Change message.
The system inserts the new message. If a change message is involved, the system sets the Change indicator.
Save your data.
Hope you find this useful.
Edited by: Reetesh on Dec 3, 2011 7:36 PM

Issue with Clipping Mask when scrubbing timeline

Has anyone encountered an issue with editing a clipping mask or repositioning it on the timeline only to see that nothing moves on the timeline when scrubbing the playhead?
This has occurred multiple times on different Edge Animate projects.
So far this has happened on SVGs, pngs, basic shapes, etc.
I posted a video in my adobe cc folder to view as a reference.
I'm using OS X 10.10.3 and Edge Animate 2014.1.1

I right click on the clip in Timeline, choose Effects Mask > Apply
The rectangular mask appears on the screen, I drag one corner in to make it smaller - what the exact dimensions are I know not. The logo I need covered happens to be almost at the exact center of the screen.
I choose the EDIT Tab > Brightness/Contrast > Set the levels so the mask is perfectly white (thus, covering up the logo) > Apply > Done
The preview works. When I output as AVI, MOV, MPG, MP4, etc., the mask that I placed over the logo has now moved either above where I originally placed it or above and to the left.
I have no idea how to answer the second part of your question.

Issue with WAN Miniport when setting up VPN server in Windows 7

Similar Messages

Maybe you are looking for