K9A2 Platinum/ problems adding 15k SAS to existing 15k SAS with Vista64 OS

This is my first build. I am trying to add a Fujitsu 15k SAS max3147rc to the existing max3147rc which has the Vista64 on it. Both disk are currently setup in the array under LD1 and LD2. This is the only way I was able to see the 2nd HD without formatting the existing HD which has the Vista 64 on it. Both show up in the arrray as Promise 1+0 Stripe/RAID0. The mode is 1+0 and raid is 0 for both drives.
Only the HD with Vista 64 shows up under my computer. Both drives show up under Disk Management. The one with OS is listed as NTFS and the other is listed as unallocatedand only has the option to make it a New Simply Volume.
Shouldn't both of these drives be on LD1 in raid0 for the fastest speed? How can it be done without formatting the drive with Vista 64 on it
Also, here is a link to a diagram of the SAS cable pinout.
http://www.cs-electronics.com/PDF/18-SAS-7P82-P1m.pdf
K9A2 Platinum/ Vista 64 Ultimate ( currently using new Beta bios because of memory 8gb memory issues)
Apevia case with gauges, 1- 120mm and 3-80mm fans
1- WD 10k raptor
2-15k Fujitsu MAX3147RC
2-2GB GSkill pc8500 1066mhz
AMD Phenom 9600BE
ATI FireGL 5600
1- DVD/CD with litescribe
1- floppy drive
1- multi card reader
OCZ 700watt ps

Bandwidth is useless when latency kicks in.
As IDE drives have a typical latency of 8~10 ms where SAS has 3~4 ms, there is no way IDE will pass SCSI bandwidth or not.
Except when you use 1 task, but a modern PC doesn't do that.
As for money on a decent RAID-controller, IDE (SATA) will not beat SCSI (SAS), no way on earth.
For click-open only access-time matters, bandwidth is second.
For AVI decoding/encoding bandwidth matters, as you have large continues files.
In my test you need to do more then 1 thing, as is common practice today, I used large files (you could use small) as they show you the difference enormously.
Try it and find out, most people that are not used to SCSI drives believe IDE can beat it.....sorry but it's not the case.
Raptors are old poor performing drives when it comes to SCSI, and the controller won't help you....try a real SCSI (SAS) Raid, it will blow you from your feet
Test under linux, gimme the results of your drives in seconds:
Code: [Select]
dd if=/dev/zero of=/export/out.dat bs=1M count=1024
Afer every test, delete the out.dat, show the result screen, then I will show the one for the forum, that has 2 SCSI drives in software-raid1
On a very old machine the result could be this:
Quote
1024+0 records in
1024+0 records out
1073741824 bytes (1.1 GB) copied, 332.856 seconds, 3.2 MB/s

Similar Messages

K9A2 Platinum PROBLEMS!!!!!!!!!!!!!

well, im on BOARD #2, and #3 is on it's way....
ok, I purchased the first board on NewEGG thogether with a Phenom 9950BE, 4GB OCZ 2x2 DDR2 1066 5-5-5-15 @2.1v and Saphire ATI HD4850. well the first try was bad, the board would not recognize my 4 WD RAPTORS, the promise controller would not detect them, and the SB600 could only read 2 out of 4 and only if 2 where connnected and not the 4....
well, I send that board back, in the mean time I visited Fry's Electronics and purchased the board again, now this time is working so, so... I managed to install VISTA64 SP1 with all the patches, etc, and play few games, except i still have problems: I disabled the promise controller as i need to run 2 ARRAY's of RAID 0 (2 Raptors 740 each, one array for OS and one for GAMES) the problem is that I get random lockups, Blue Screens, etc. also when I choose to restart the computer or send it to SLEEP, as it is shutting down the HD make a weird sound that they never made before and if I restarted the SB600 raid bios would not detect the arrays, i physically have to power down, wait and restart, so the arrays are detected.
also I try to overclock the PC, the Phenom is able to run at 3ghz but it freezes some times immediately but others it would last few hours with gaming in between, i tried several voltages from 1.33v to 1.41v and some times get a BlueScreen that reads a processors error, one core did't respond on expected time... or something like that.
[bashing removed]
my spec's are:
AMD Phenom 9950 Black Edition B3
MSI K9A2 platinum 1.5 bios
Saphire HD4850
4GB OCZ DDR2 1066 5-5-5-15 @2.1v Dual CH.(2x2GB)
4x WD RAPTORS WD740 on RAID 0 (two ARRAYS)
PIONEER DVD-RW DL IDE
CoolerMaster STACKER case w/2 120mm fans and 1 80mm
Dual PS: CoolerMaster Real 450w PS & Ultra 400w PS

well, the design of the CoolerMaster STACKER case is for two Power supply's working in tandem, it has a connector that turns on both supply's at the same time, so I split the load as follows: all Motherboard plugs, 3 120mm fans, 1 80mm fan & Pioneer DVD drive; powered by thr CoolerMaster REAL 450w, it list power as follows: PEAK (60S) +3.3v@30A, +5v@35A, +12v1@18A, +12v2@16A, -12v@blank?, [email protected].
CONTINUOS: +3.3v@20A, +5v@25A, +12v1@12A, +12v2@10A, [email protected], [email protected]
as for the other power supply it powers the following: HD's (as of now 2; 1 WD Raptor and 1 Seagate 7200.9), 1 120mm fan and the ATI HD4850
I don't think Im starving the system of power...
im installing windows vista 64 (yeah, yeah, XP is more stable, but I had an ABIT A8N nforce4SLI, Athlon X2 3800 OC's, 2GB Patriot DDR, 2x Geforce 7800GT OC's on SLI and 4 HD's, and I never had any problems, and I had the CPU running on stock cooler and stock voltage. and I had VISTA 32, and 64 and never since I bought it ever give me problems, i could OC everything from CPU, memory, HT, PCI-e, etc.
why this board is so bad?
this is the current ERROR i have just now:
"A clock interrupt was not received on a secondary processor within the allocated time interval..."
technical info. ***STOP: 0X00000101 (0X0000000000000031, 0X0000000000000000, 0XFFFFF980012C6180, 0X0000000000000001)
I did enable promise controller and used the 2 HD on the ports controlled by it as JOBD each, the RAM is @ 1066mhz, voltage as recomended 2.1v and I did try to OC the processor just to try, since that is the purpose of buying the Black edition 9950 to 15x200 @ 3000mhz 1.41v, everything else is on Auto.
before I get SCHOOLED by other users, yes I do want to OC the proc. I have installed vista 64 w/o OC the proc and it runs ok, but i still had random BSOD here and there... but since this is proclaimed the best board for OC the Phenom and AMD even pushes the SPIDER plataform and makes it easy to OC. I also just installed an after market heatsink (CoolerMaster Gemin II w/2 120mm 1200rpm) and the bios reports the CPU @ 29* C

MOVED: K9A2 Platinum PROBLEMS!!!!!!!!!!!!!

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=120199.0

Quote
I´m quite confused by the fact that when i rolled back to the original BIOS that came qith the mobo, the problems were not solved.
Quote
3GB (3x1) OCZ platinum rev2 DDR2 800
Use 2 memory sticks in 1st two DIMM's near to CPU socket.
Also apply memory voltage to 2.0-2.1V in BIOS cell menu.
Re-test.
And also stop with BIOS flashing

Having a problem adding programs to my existing Creative Cloud desktop

Originally installed Creative Cloud and a few programs about 3 months ago and all has been working well.
I have been trying to add additional program but consistently have a problem and get error messages including my Adobe product is not a genuine item (which cannot be since it is downloaded through my account).
Used to be able to call for help, but that does not seem to be an option.

Check this KB as it may help :-
http://helpx.adobe.com/creative-suite/kb/genuine-verification-failure.html

K9A2 Platinum Cold Boot problem

Hi, recently I have encounter this problem on my K9A2 Platinum that didn't occur before, where after powered off for a few hours, when booting up, there is power to the system but the system won't boot (i.e. no POST or anything). The reset button on my chassis also won't work at that time. And after pressing the power button to shutdown, it won't power up again until I've turn off the mains and wait until the power LED on the mobo to turn off and turning on the mains again.
After that, my system would be able to boot successfully, but the bios clock will be slow by a few hours. E.g. current time 9am, bios time 5am. I've tried flashing the bios to the latest version and resetting the bios settings doesnt help at all.
Can anyone plz help me?
My current rig config is
K9A2 Platinum w/ phenom 9500
6gb kingston ddr2 1066mhz
PowerColor HD3870
Xonar Essence STX
Coolermaster RPP 750w
Thanks a lot in advance.

Quote from: Henry on 23-March-10, 07:29:17
Did your problem start after you added this mixed batch of RAM? When did you add RAM to what you had 2 years ago? AMD works best when only 2 sticks are used and you have messed that up by adding 2 more sticks of different RAM. Does it work OK if you remove two of the sticks?
Not really, I had the mixed batch of ram for almost 8 months without any problems. And the cold boot problem does not happen everytime. I've just tried booting up without any issues this time round. I would see if the problem occurs again and test it with a new cmos battery.

Problem unscrewing K9A2 Platinum mobo from case

I need to move my K9A2 Platinum mobo ( along with peripherals and add-on boards ) to another computer case. All has gone well with removing all my peripherals and add-on boards from the old case but when I have tried to remove the mobo a two of the screws cannot be unscrewed. They were held to the bottom of the old case with metal clips. I could eventually remove the mobo by forcing out the metal clips but no matter what I try I cannot seem to unscrew either of the screws from its metal clip. Whether I hold the metal clip on the bottom of the mobo in place and unscrew the screw, or whether I hold the screw in place and turn the metal clip on the bottom of the mobo, the threads holding the screw to the metal clip are not unloosening the screw from the metal clip.
I seem stymied. The only practical solution I can think of is to cut through the area holding the metal clip on the bottom of the case with some sort of small blowtorch-like device, if something like that exists, but naturally I am afraid any heat I apply will damage the mobo.
Thoughts ? Suggestions ? I really need to get these clips off so I can transfer my mobo to another computer case I have since it is my main desktop computer right now, although I will soon be building another system

Another thing you can try is carefully pull on the to put pressure against the screws and then see if it helps to get the threads engaged. If no luck then your only other choice is to carefully drill out the screws and hope the drill doesn't slip and damage the MB.
I have had similar problem in the past and putting pressure against the screw like that usually does the trick.

Houston, we have a problem.. My new K9A2 Platinum will not install an OS

I purchased a K9A2 Platinum (Version 1) and everything went fine with the hookup and install until I went to install the OS.
Here's the set up:
1) 9600 Phenom
2) 4 GB A-Data DDR2 800 RAM (2 2GB Sticks)
3) Diamond HD3870 Video Card.
4) 260 GB WD Caviar Sata Drive
5) LG 18x DVD
note I also Have a 160 GB PATA WD Caviar as well.. more about the in a minute.
I hooked everything up Sata drive as Sata 1 and DVD as Sata 2,
Checked BIOS to be sure everyone was recognized.
Tried to install Vista 64 bit.
Entered Location, activations etc..
and Install began
1) Copied files
2) Expanded files
3) Updated system
(no errors occured during these steps)
System rebooted and got the message Windows is booting for the first time etc...
Then to the finalizing Installation line, which... well.. never gets final (I've left it on that screen for 3+ hours).. Sometimes it locks up.
I tried installing Windows XP and I get through all of the installation, but when it reboots to WIndows from the DVD.. It can't find the OS..
I installed the PATA drive and tried installing Vista to it with no difference in the results. I suspect I am doing something stupid here (I have done this before.. it's my fifth build and never a problem before). A note that on the PATA if I use the Chip Select jumper (Out of the box settings) Everything's recognized but it sets it up as a slave. IF I set it as a lone master the BIOS recoginizes it, but windows doesn't. If I set it up as a master.. the system doesn't post. I am going to try to install XP on the PATA and see if that works, However I want to run Vista on this beast, so even if it does, well I still need help..
Yes I promise, this is all a cry for help... If anyone has any ideas I'd surely be apreciative.. In fact I'd be so appreciative I'd help you remove an garbage (viruses, spyware etc..) for free (ok I do that for free anyway.. I'm cajuntek everywhere I go on the net.. You can find me in the Security Cleanup forum at dslreports most often.. Thanks again for any help you guys can provide on this.

I don't trust [Auto] Vmem in the BIOS.
First, Cajuntek, I would try beta BIOS 1.33.
You can download it from http://www.magnaroute.com/deliver/
This BIOS has been very stable for me, MSI Tech Support gave it to me to attempt to solve memory stability I have had with 4x dual rank memory modules. It doesn't fix that problem but it does make the system more stable and compatible over the publicly released BIOSes as far as I can tell.
I would also suggest you put in a fixed voltage value in the BIOS for your memory. I use 2.3V because I am overclocking. You can probably use 2.0V or 2.1V. It is possible that the [Auto] setting may be giving your system too little voltage on the memory and that may be causing your lockup.

K9A2 Platinum Boot Problems

Dose any one know why I cant' boot from the DVD drives that I have connected to The SATA ports 5&6, I can see the drive in the CMOS boot order and I chose the first DVD Drive (Port 5) as the first boot disk. Is it even Possible to boot from the Promise T3 Controller on the MB (K9A2 Platinum V1). I am using the other controller (sb600) for a RAID 0=1 Array. I ma trying to install windows 7 rc.
In order to install XP Pro I had to temp in an IDE CD/DVD drive on the MB IDE Connector

Maybe the DVD-device has a problem, as in not working all that well.
One troubleshooting step would be to try a different port, 5-6 is aimed at RAID it says on the home page:
http://www.msi.com/index.php?func=proddesc&maincat_no=1&prod_no=1332

K9A2 Platinum Bus Interface problem

Currently running:
Motherboard: MSI K9A2 Platinum 1.6 Bios
CPU: AMD Phenom 9950 BE (O.C. to 3.0 [200 x 15])
RAM: 8 GB G. Skill 1066 RAM (Underclocked to PC 6400 4-4-4-12 for stability)
GPU: 2x Radeon HD 3870 Sapphire Edition
HDD: 2x Seagate 640 HDD's RAID 0 thru SB600
OS: XP Pro x64
My problem is my 2 GPU's have a max bus width of 16x 2.0. When using GPUz, only the first card is rated at 16x 2.0, while the second is 16x. Both cards are in the dark blue "mazerine" slots, and the BIOS option for High Speed mode in slots x1 and x4 are turned on "auto." Any ideas?

Quote from: Stu on 03-January-09, 02:49:08
Are you actually having any problems using the cards?
Normally I can run Farcry2 on Ultimate at 30-40 FPS no problem, however, with the bus width labeled as such i'm running around 4-5 FPS, so the 2nd card is creating a slowdown. I know the card is fine, because when it runs by itself not in x-fire at PCI-E x16 2.0.

K9A2 Platinum Audio and Video Driver problems.

I put together my new rig last night and am having a lot of problems with drivers. The rig installed windows XP SP2 in about 10 minutes though
Rig:
MSI K9A2 Platinum Bios 1.3
Phenom 9850 BE
G.SKILL 1066 5-5-5-15 2T
MSI HD 3870 OC
WD Raptor
CoolerMaster 550watt
Several fans to keep cool air flowing.
My problem is that I can not find good audio or video drivers. I started by trying the audio drivers included with the board, but they would not complete the install. I ended up downloading audio drivers from the MSI site, however they also would not install with the "#-0001" error message. I followed the instructions on the forum: https://forum-en.msi.com/index.php?topic=115396.msg866810#msg866810 including installing the MS HD Audio Driver Hotfix but still cannot get sound working.
To further complicate my problem the 3870 has HD onboard, which makes a second instance of Microsoft UAA HD Audio driver in the device manager, and also tries to find drivers for bits of it's audio hardware.
Currently I have disabled on-board audio completely through the bios, and now everytime I boot-up I get new hardware found for UAA HD Audio, and also some Media interface. Clearly this is the HD on the 3870, however I can't seem to get drivers installed that will agree with the hardware thus the message continue to pop-up!
Does anyone have suggestions or similar experiences?

Quote from: AMDloyal on 24-April-08, 09:56:10
Thanks for the links.
The standard AMD ATI Drivers + South Bridge chipset drivers worked flawlessly. I've made a clean run through 3dmark06 so i feel good about them.
As for the audio.
I've worked through both of those suggestions but haven't gotten anywhere. A few times I have been able to get the drivers to install without the "error code -0001" message, but that doesn't give me sound. Under device manager I still end up with yellow exclamations. It seems no matter what I disable or try to do nothing works. I've tried updating drivers manually like was explained in the first link, but when the update is complete I get the messages lile: "There was a problem installing this device MEDIA An error occured... The data is invalid"
Does anyone know if this indicates a hardware of driver problem?
"Thanks for the links.
The standard AMD ATI Drivers + South Bridge chipset drivers worked flawlessly. I've made a clean run through 3dmark06 so i feel good about them."
you are done well.
As for the audio.
I've worked through both of those suggestions but haven't gotten anywhere. A few times I have been able to get the drivers to install without the "error code -0001" message, but that doesn't give me sound. Under device manager I still end up with yellow exclamations. It seems no matter what I disable or try to do nothing works. I've tried updating drivers manually like was explained in the first link, but when the update is complete I get the messages lile: "There was a problem installing this device MEDIA An error occured... The data is invalid"
Provide screenshot from Device manager.

K9A2 Platinum Sata Raid Problems

I could not get my 2 500 gb seagate 7200.11 drives to work on the sb600 raid controller, in raid 1 (set to raid mode in bios). I'd set it up and it would remain functional until I formatted it and put stuff on it. Then when I restarted, it says critical and can't locate the second drive, but it shows up in the list of definable drives. My older 200 gb seagates 7200.9 in the same setup do not have this problem. I finally got my 500s working by hooking them up to the promise controller instead. (Although no longer a current problem, I wouldn't mind knowing what would cause this for future occasions.)
My new problem is, I had to unhook all but the drive I wanted to install Windows XP on (A separate 120 JBOD configured drive) so I could get it to be C:/. This all went fine. However when I hooked up the 500s again, Windows XP would not boot, the screen just stayed black, with them not hooked up, it boots just fine, with the 200s as well. When running the Windows XP setup again, the 500s appear as C:/ instead of the 120 in the disk select screen of the install. It's like the 500s took over the drive letter when they are hooked up and thus can't load. Is there some way to stop it from doing this or am I completely off on this.
My computer spec is:
K9A2 Platinum
AMD X2 6000
2*2gb OCZ PC6400
ATI Radeon 3870
700 Watt OCZ PSU
Update: Installing XP ignoring the fact its not C: fails. It copies all the files onto it, then after restarting I get a black screen.
Another Update: On a whim I tried disabling the SB600 raid and set it to AHCI instead as I read that other people were having problems with it and it all works perfectly now. It's too bad this doesn't work, but I'll just put the 200s back in my old computer instead.

I'm having the exact same problem you did. Same Mobo. Except I started off with Promise RAID 1 because when I tried using SB600 RAID, my SATA DVD drive would not function in Vista Ultimate x64. So I had my Raid 1 configured on Promise T3 with BIOS 2.8.1030.0021 using 2 320GB drives. One of them Seagate, one WD, both 3GB/s transfer, only difference was that Seagate has 16MB cache, while the WD has 8MB. But both drives worked fine in the array for some time, and then after doing some updates from Windows Updates now the Raid config shows that encountered a critial status, "A disk member of an array has failed or is not responding", "Problem is detected with Array : 1". And when I go to the see the Array status it shows the Seagate drive on ID channel 1, but for the 2nd drive it shows questions marks all the way through the item line. I checked the drive, it seems fine. And even when I go to define a second Array, it shows the WD available on channel ID 3. So it definitely see both drives, but how do I re-add that WD drive that it doesn't see to my earlier defined array without loosing data on my Seagate drive?

Continuing K9A2 Platinum & Vista Install Problems - new variance

Hi All,
This is a contiunuation of my earlier post. https://forum-en.msi.com/index.php?topic=113866.0
My full system specs are:
MSI K9A2 Platinum MB
OCZ Technology 2x2GB 240DIMM PC2-6400 Gold
AMD Phenom 9500
2 x Samsung SATA DVD Writer SH-203B/BEBN
GeForce 8800GTX 768MB PCIE DVI
Coolermaster Cosmos case
Seagate 320GB SATA2 HDD ST3320620AS
OCZ 1010 GameXstream PSU
Following the problems described in my earlier post (see above) - which I thought were HDD related - I have tonight bought the Seagate HDD listed above. Installed the HDD, attempted to install Vista Home Premium 64.
Installation seemed to go fine, towards the end - when you get the 'Windows will now start for the first time" screen - the system blue-screened (too quick to get the message, looked like a RAM issue) and crashed. Re-started and then the installation aborted itself.
Second installation try: The system went through the installation process, I passed the bit where you choose the partition to install (did a format), installation seemed to go fine, one re-start, system gets stuck in the 'Completing Installation' phase, I would say roughly around 70% installed according to the blue progress bar.
Interstingly, when I now attempt to perform a new installation attempt I do not even get to the screen where you choose the language and country settings, I just get stuck at the black screen with the Microsoft name written and the green, interrupted bar sliding from left to right.
Am I back at the same stage where I was in my previous post https://forum-en.msi.com/index.php?topic=113866.0
This is crazy. I have built around five or six systems so far and never had problems like these...
Please help.
C.

@Russ_xp: No, not yet. I have been scouring the OCZ site to get an idea on compatibility and settings but have been disheartened when the advice for the K9A2 and my memory modules said: "Please call"
Sent an email to European support of OCZ and am awaiting their reply...
I had a look at the memory timings in the MB's BIOS, though and have to admit that I was baffled by the number of different settings that I could manipulate. On the MB's that I played with before there were less fields to manipulate so entering 5-5-5-15-2T was easier (don't laugh).
Cheers,
C.

PROBLEM RAID K9A2 Platinum

hello,
I have a problem for the raid on my msi k9a2 platinum.
currently, I have 2 SATA hard drives, on first (samsung 750 GB) I have vista ultimate 64 installed, and on second (maxtor 200 GB) I have games. in the bios I see "Raid: Ide" and when I met "Raid: Raid" blue screen at startup vista.
thanks
phenom 9600 Be
MSI K9A2 platinum
Sapphyre 3870 hd toxic
2 x 1g 1066 Mhz Kingmax
Samsung 750 Go & maxtor 200 Go
2 x HPw2207h

Why are you trying to run a single drive in RAID mode? Sounds logical that Windows would Blue Screen, you have no RAID array. Just keep it running at IDE mode, should be fine...
PCI latency should be set as low as possible, though I doubt you will notice any difference between the 64 and 32 settings. This setting mostly applies when you have add in cards that need to hold the PCI bus longer than default...

K9A2 Platinum Raid problem

Hi i have 4 days trying to install my new system. And the mobo do not want to recognize the drives in sata 5 and 6, those controlled by promise.
My system specs:
Phenom 9600
MSI k9a2 platinum
6 samsung hard drives SATAII 7200 rpm
8gb ram Corsair Dominator 1066 MHZ
2 x Diamond ati HD3870 512 mb GDDR4
Thermal take toughpower 850W PSU
I want to run:
RAID 1+0 With 4 drives of 320GB each using sb600 controller
and two 320 GB single drives, NON RAID on the promise controller.
How can i run this config on my mobo? it is possible? i need detailed bios settings for this please.
Second alternative config:
Raid 0 on sb600 using 4 disk
Raid 1 on promise using 2 disks
I have 6 drives in total and want to use them all.
Right now if I enable additional raid config on BIOS my sb600 controller only detect disks on the 1 and 3 ports, but doesnt see the 2 and 4 ports. Also i cant see the 5 and 6 ports anywhere in the bios or in the ctrl-f raid utility.
My bios version is 1.3
Any help?

hi, you could use the promise controller for your raid array using the rear esata connectors (with a esata to sata cable) and in side ports 5-6, use the sb600 not in raid for the other drives, like bas was saying each controller has it own bios, so what that means is if promise raid is on (sb600 off) the drives would show up in the promise raid setup and the other way around (drives in the SB600 RAID set up) and also if both raid controllers are off the drives show up in the main board bios. once i did have both controllers run through their setup at the same time but i got "some memory ran out of room" message after post,..
anyway so you should be able to do what you want, but use the promise for raid and sb600 for not, that way only one raid controller is on.

K9A2 Platinum Raid 1 Setup / Installation Problem

I'm trying to setup a raid 1 with my new K9A2 Platinum board. I would prefer to use the promise controller but have had no luck with the SB600 or Promise.
My PC:
2 gig GSkill Ram 800mhz
2 Identical Seagate Barracuda 7200.10 hard drives
750w Corsair psu
AMD 5200+
Vista Home Premium
GeForce 8600GT
The first hard drive has everything loaded on it including all my business and personal data, so I don't want to reformat and start over with that drive. I just want to add another drive as a mirror for redundancy purposes.
Symptoms:
I can't select my RAID configuration in the Fastbuild Utility. It will show me the current drives as connected, Model, Capabilities, Capacity, RAID mode (showing JBOD), and Status (Functional). The bottom of the screen doesn't give me any options, it just says "Any Key to Continue" at which point it brings me back to the main page of Fastbuild. I have a pictures of the relevent screens, just haven't figured out how to post them here.
What I've already tried:
Enabled the SB600 as Raid while drives plugged into SATA1 and SATA2. (once each with Onboard controller Enabled and Disabled)
Enabled the OnBoard Controller while drives plugged into SATA5 and SATA6 (once each with SB600 set as RAID, set as IDE, and Disabled)
So how do I select RAID 1 as my configuration?
TIA.

Steps to RAID 1:
1) Backup your data to a third drive.
2) Connect both Seagate drives to the Promise controller.
3) Enable the Promise controller in your BIOS.
4) Enter the FastBuild utility using CTRL + F.
5) Select 'Define Array' (I believe it's option # 3).
6) Define parameters and asign drives to the array
7) Save and reboot.
The RAID 1 array is now active. If you plan to install an OS on it, you will need to load a driver during setup. For WinXP you will need to use a floppy and F6, for Vista you can use other media as well (CD-ROM, USB stick, etc.).
If you plan to run your OS from a third drive, you will just need to boot to the OS and access the Drive Manager. Create a partition on the RAID 1 array, the OS will format the array and it will prompt you to reboot when finished.
Regarding the external drive, it's best to use a hard drive of choice and an eSATA external enclosure. I use an ICY IB-351 BL Series for example, it has eSATA, Firewire and USB 2.0. I also have a Cooler Master X-Craft, same idea. It might come in handy to be able to swap drives...

K9A2 Platinum/ problems adding 15k SAS to existing 15k SAS with Vista64 OS

Similar Messages

Maybe you are looking for