Less than 1Mbs

hello im using the netgear DGN2000 and im only getting about 0.6mbs i used to be able to get 1.3mbs if i was lucky but now its just seems like its stuck at this even slower speed. i always get pages not loading on firefox and i have to refresh then it works but its disgusting how BT can get away with these **bleep** speeds

i have just found out the noise aswell if that helps in anyway
System Up Time 23:07:58
Port
Status
TxPkts
RxPkts
Collisions
Tx B/s
Rx B/s
Up Time
WAN
PPPoA
1097757
1693233
0
1122
25797
23:06:24
LAN
10M/100M
1620700
1027455
0
24806
1239
23:07:54
WLAN
11M/54M/130M
143576
83542
0
1491
168
23:07:33
ADSL Link
Downstream
Upstream
Connection Speed
960 kbps
448 kbps
Line Attenuation
59.0 db
30.5 db
Noise Margin
9.7 db
17.0 db

Similar Messages

  • Less than 1Mb upload speed

    Hello everyone
                         I have been with BT infinity for a good few months now but this issue has become too big a problem. I have tried to fix it myself to no avail. My issue is terribly slow upload speeds, always less than 1Mb, on some occassions less than 0.5Mb.
    Here are the results from the wholsale speed test
    I have run many different speed tests online, and on both computers in the house. Both machines show the same terrible upload speed. I do not expect to get the full 10Mb of the IP profile, but I would like to get it to atleast 2Mb so I can stream my games online via twitch and upload youtube videos in less than 10 hours.
    I have tried resetting machines, the router and the modem but it made little difference. I would greatley appreciate any help you can provide with this issue, thankyou.

    This test was run on a wireless connection, however I have also run the test on wired. This usually results in a very marginal increase in download speed, but absolutely no change in upload speed.

  • Infinity less than 1mb!

    Joined by infinity end April and had 75mb (1st in street to get it), now 5-10 others in street have it we are down to less than 1mb frequently. Restart the hub 5 will push it up to 4mb. Wow!
    Clearly something not right but I'm paying shed loads for a service I'm simply not getting!
    1. Can I get 75mb again?
    2. Can I cancel contract?
    3. Can I claim - not fit for purpose?
    Cheers folks

    From your previous post apt beginning of May did you phone the fibre helpline number posted by john46?  If so did you get engineer visit to check your connection?
    If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
    If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

  • Internet slows down at night to less than 1Mbs, poor customer service

    I'm having the same problem. I had originally 1-3 Mbps (Oct 2008 - Jan 2012). It used to work fine but then the speed seems to be slowing down as years passed by, I was getting less than 1Mbps most of the time so I upgraded to 3-7Mbps with 2 years holding period (Jan 2012 to Jan 2014). From Jan 2012 to Nov. 2012 it was fine, then starting Dec. 2012, the internet started to slow down at night. I'm getting 6-7Mbps during daytime and until around 9pm, then the internet slows down to less than 1Mbps after 9pm. Then starting mid January 2013, the situation seems to get worst, the internet slows down starting around 7pm, and then on the 3rd wk of January, the internet started to slow down as early as 5pm.
    I've contacted the customer service twice. First, the person who attended remotely accessed my computer and after more than 15 minutes trying to find fault at my computer, wiring, set-up or wireless router (instead of the verizon network), he realized he doesn't have any excuses and instead instructed me to hard reset the modem. I told him that if I hard reset the modem, he will be disconnected to my computer. He said, "that's fine, I will call you you to give instruction on how to set-up the modem". After I have hard reset the modem, he never called up and I was left all by myself figuring out how to set-up the modem. I've contacted the customer service the 2nd time, a different person attended and exactly the same thing happened, the guy instructed me to hard reset the modem but never called up after he got disconnected. I guess this is their expertise, how to rudely leave the communication once they figure out that they can't resolve the problem.
    Once the 2 years holding period is over, I will change to other internet provider and will never switch back to verizon again. I will never ever recommend verizon to my friends and will share them my experience with verizon.

    This is one of the reasons we are leaving Verizon as well.  We previously left Brighthouse because the initial deal sounded great, until the rebates expired.  When the price jacked up, I told them they had to better because Brighthouse was much less expensive for the same package but their service didn't slow down at 7pm.  The customer service agent said I really couldn't compare the two because Verizon has a superior quality of service.  I asked, "Then why does my internet slow down around 7pm, because the Brighthouse service didn't do that".  All the customer service agent has to say was, "That's not true."  Nice try.  He essentially called me a liar, about something I've seen firsthand, and I have experienced that same 7pm slowdown with a similar service we had in NC.  Sorry Verizon, we left Brighthouse because we thought we were saving a few bucks, and getting a higher speed on our internet.  Not true on both accounts and we're going back.    PS To the person who made this initial blog post, I noticed there were 484 views but no "likes"  - it's because that button won't let you click it, at least that's what I experienced on my end.  I'm certain there are a lot more people out there who deal with this same issue and are quite frustrated. 

  • Infinity woes Speeds less than 1Mb/s!

    Please Help!
    I've been back and forth with BTIndia for two weeks and I'm now starting to feel nothing will help me!
    I've recently moved up from BTBroadband Option 3 to BTInfinity.
    My main machine is a 2.66 GHz iMac connected to the HomeHub via Ethernet (I also connect a couple of PCs via Ethernet and Wifi).
    The speed on ADSL was pretty consistent and acceptable - I could stream Youtube and the like and p2p was fast enough for me to download quickly. I could generally download up to 1.4MB/sec actual - which was fine.
    The OpenReach engineer arrived on 20th December and assured me that the line from the Green Street Cab was good and I should expect speeds of 37.5 MB/s download, 10 MB/sec upload. I didn't seriously expect that but would have been happy with a speed bump of Double my previous speed. I didn't. Not by a long way!
    He checked the line and confirmed a Line Speed of 38.5 MB/sec and went away. Didn't check my actual browster DL speed. It was appalling. After a day of buffering on any streamed video and App updates on my iPad that took hours instead of seconds I tried a couple of online Broadband Speed checkers and they all said the same thing. An upload speed of 7-8MB/sec (Fine!) and a download speed of Less that 1MB/sec!!!
    I called BTIndia and they arranged (in fairness, quickly) an engineer call-out. He checked the equipment and said it was all fine and was stumped as to why my DL speed was SO slow. He thought maybe my IP profile had not been configured properly and after a long time got through to "somebody" who promised to check it. Upshot...Nothing changed.
    Called BTIndia again...another engineer visit. He heard from the previous OpenReach guy that the Equipment/Line from Cab to socket was fine so he tried a "Bait and switch" - I THINK rewiring between the "Infinity" cab to the phoneline cab. I'm very vague on this so I may be wrong.
    Lo and behold! Infinity speeds of 38 MB/s!!! Bliss.
    Off he goes and 10 minutes later Bam! Back to 1MB/s!! What the?...
    I've had ANOTHER OpenReach engineer visit on the 3rd January and the same story. Equipment is fine. Something somewhere is not configured correctly.
    I am BEGGING!!! someone out there that has heard of a similar problem. Please...Is there a solution? What questions should I be asking BTIndia? I'm not an TCP/IP expect and nobody seems to know what to ask to whom?
    Sorry the post is so long, but I wanted to make sure you had all the info.
    Cheers
    Mark W

    Here is the speedtester results
    FAQ
    Test1 comprises of two tests
    1. Best Effort Test: -provides background information.
    Download Speed
    2234 Kbps
    0 Kbps
    38710 Kbps
    Max Achievable Speed
    > Download speedachieved during the test was - 2234 Kbps
     For your connection, the acceptable range of speedsis 12000-38710 Kbps .
     Additional Information:
     IP Profile for your line is -38710 Kbps
    2. Upstream Test: -provides background information.
    Upload Speed
    6271 Kbps
    0 Kbps
    10000 Kbps
    Max Achievable Speed
    >Upload speed achieved during the test was - 6271 Kbps
     Additional Information:
     Upstream Rate IP profile on your line is - 10000 Kbps
    This test was not conclusive and further testing is required.This might be useful for your ISP to investigate the fault.If you wish to carry out further tests,please click on 'Continue' button.If not, please close the window using 'Exit' button and contact your ISP for further assistance with these results.
    Pretty Woeful eh?

  • Less than 1mb downstream, please help.

    Hey All,
    Dont know if any can help.
    Ive (touch wood) had very few problems with my broadband however the last couple of days the speed has dropped dramatically.
    I usually get around 4mb but currently am lucky if I get 1mb. Nothing has changed in the house.
    I tried to use speedtester.bt.com to measure what I am getting but get this error.
    The Performance Tester is currently unable to run a speed test for your broadband connection. Please try again shortly, however if this problem persists, raise the issue with your service provider.
    Here are my homehub stats. Any help is greatly appreciated.
    ADSL line status
    Connection information
    Line state
    Connected
    Connection time
    0 days, 9:45:08
    Downstream
    1,824 Kbps
    Upstream
    448 Kbps
    ADSL settings
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    ITU-T G.992.1
    Latency type
    Interleaved
    Noise margin (Down/Up)
    21.8 dB / 18.0 dB
    Line attenuation (Down/Up)
    47.0 dB / 28.0 dB
    Output power (Down/Up)
    17.4 dBm / 11.9 dBm
    Loss of Framing (Local)
    0
    Loss of Signal (Local)
    0
    Loss of Power (Local)
    0
    FEC Errors (Down/Up)
    648790 / 4
    CRC Errors (Down/Up)
    1 / N/A
    HEC Errors (Down/Up)
    N/A / 3
    Error Seconds (Local)
    1
    Solved!
    Go to Solution.

    Hi Welcome to the forums
    Here are some help pages done by CL Keith http://forumhelp.dyndns.org/speed/Speed.html
    Can you also post the full results from BT Speedtest speedtester.bt.com
    Have you tried connecting to the test socket at the rear of the master socket  
    Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
    This is a customer to customer self help forum the only BT presence here are the forum moderators
    If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

  • BB speeds of less than 1mb. Why?

    Hello, we've had a fault on our phone line fixed today but whilst phone is back and BB is now stable it's only 1mb. (The fault was underground cable had sheared - phone-line out completely, BB intermittent and below 1mb for last 5 days.) 
    Any ideas? Our test results are below. Thank you.
    Homehub 3
    ADSL Line Status
    Connection Information
    Line state:Connected
    Connection time:0 days, 00:23:07
    Downstream:5.156 Mbps
    Upstream:448 Kbps
    ADSL Settings
    VPI/VCI:0/38
    TypePPoA
    Modulation:G.992.1 Annex A
    Latency type:Interleaved
    Noise margin (Down/Up):6.6 dB / 19.0 dB
    Line attenuation (Down/Up):45.5 dB / 25.0 dB
    Output power (Down/Up):19.8 dBm / 12.2 dBm
    FEC Events (Down/Up):763 / 0
    CRC Events (Down/Up):3 / 0
    Loss of Framing (Local/Remote):0 / 0
    Loss of Signal (Local/Remote):0 / 0
    Loss of Power (Local/Remote):0 / 0
    HEC Events (Down/Up):22 / 0
    Error Seconds (Local/Remote):2 / 0
    BT Speedtest
     Download speed achieved during the test was - 1.4 Mbps
     For your connection, the acceptable range of speeds is 0.4 Mbps-2 Mbps.
     Additional Information:
     Your DSL Connection Rate :5.28 Mbps(DOWN-STREAM), 0.45 Mbps(UP-STREAM)
     IP Profile for your line is - 1.25 Mbps
    Solved!
    Go to Solution.

    Welcome to this customer to customer forum.
    Leave it connected and the IP profile will recover in a few days. Please do not restart the home hub.
    There are some useful help pages here, for BT Broadband customers only, on my personal website.
    BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

  • Intermittent connection - Now slow less than 1mb

    Hi
    I have reported issues to BT and Talk Talk for a number of YEARS now. Having returned to BT in January out of frustration I am now faced with the issue all over again.
    At times, randomly it appears, my BB cuts out when recieiving or making landline calls. This will happen a lot for a period of time and will reduce the profile of the line to 1mb from 3.5-7mb. I have had several engineers over the last few years visit the property and on every occassion they never found a fault at the house and have always remarked that inspite of distance from the exchange that db levels where low and signal was good. Normal service can last from a week or two to a few months.
    For another week now I have had to deal with almost dial-up connection and download speeds. I can't effectively work from home, participate in gaming events or even recieve video birthday messages from family and friends
    here is a copy of the last BB speed test.
     Download speedachieved during the test was - 0.96 Mbps
     For your connection, the acceptable range of speeds is 0.2 Mbps-1 Mbps.
     Additional Information:
     Your DSL Connection Rate :1.25 Mbps(DOWN-STREAM), 0.45 Mbps(UP-STREAM)
     IP Profile for your line is - 1 Mbps
    I have tried to be patient and wait for automatic profile update but the profile is going down not up and download speeds are now stuck at 88-101kb/s.
    I have done all the required checks of pc, wires, router and master socket. Noise continues to be a feature of most landline calls albeit at present these don't appear to be causing BB disconnects.
    Having been without and ADSL signal for 4 weeks in Dec and Jan and now facing this for the last week or 2 I am really at the end of my resolve as to what more I can do.
    If needed, I would be happy for you to disconnect all voice calls on the landline and have voice calls diverted to my mobile in a hope to maintain a reliable and useable BB service which I, like others these days, rely on. Any solution would be welcomed. Please.
    Thank you

    I have reported the same issue before via phone faults but as the issue is intermittent they have never confirmed a line fault.
    Having spent a Month with no ADSL signal in January where I reported the issue to both phone and BB and all I ever got was 'well there isn't a fault showing at our end'. The BT openworld engineer on 30th January checked the house etc etc and found nothing wrong with internal wiring. He completed a number of tests using an array of equipment and confirmed that there was no fault on the line despite there not being an ADSL signal.
    He made a call and had something reset and hey presto within 2 mins I had 3.64Mb and a download rate of over 400Kb/s. He asked me why 1st and 2nd line support hadn't requested the same...I wont repeat my answer!
    As you can imagine, I am frustrated as this saga continues here are the latest stats after a full and lengthy reset.
    Clearly there is an issue with the cable running to the house or to the exchange but being underground I am guessing it must be environmental but I have no way of replicating the fault
    Thank you
    Download speedachieved during the test was - 0.95 Mbps
     For your connection, the acceptable range of speeds is 0.2 Mbps-1 Mbps.
     Additional Information:
     Your DSL Connection Rate :3.52 Mbps(DOWN-STREAM), 0.45 Mbps(UP-STREAM)
     IP Profile for your line is - 1 Mbps
    ADSL Line Status
    Connection Information
    Line state:
    Connected
    Connection time:
    0 days, 02:09:11
    Downstream:
    3.438 Mbps
    Upstream:
    448 Kbps
    ADSL Settings
    VPI/VCI:
    0/38
    Type:
    PPPoA
    Modulation:
    G.992.1 Annex A
    Latency type:
    Interleaved
    Noise margin (Down/Up):
    10.3 dB / 22.0 dB
    Line attenuation (Down/Up):
    51.5 dB / 29.5 dB
    Output power (Down/Up):
    19.5 dBm / 12.4 dBm
    FEC Events (Down/Up):
    1154 / 0
    CRC Events (Down/Up):
    2 / 0

  • Infinity dropped from 25Mbps down to less than 1Mb...

    As advised I am opening a new thread for this.
    I have had infinity for a month or so and at first the speed was fine. But since xmas it has seemed to get slower and slower. I have run just run the speed test results below. It is worse than the worst I ever got from normal broadband. What am I paying a premium for ?
    As advised I will turn off and on the modem and do nthe test again. Will post the results when I have them.
    Solved!
    Go to Solution.

    After rebboting the modem and openreach box have re-run the test and it seems ok now.

  • I have a problem with iCloud - i have great internet access at work, but slow internet access at home (less than 1MB/PS) and I use the full range of iCloud syncing facilities. How can i make my devices ONLY sync at work.. and not at home??

    As stated above, if i go out during the day, buy an app, download a song and take 20 photo's when i get home my devices will all take 30mins to sync before i can even browse websites or check my facebook at home.
    Can i set up my iCloud to only sync when i am on my work Wi-fi...?

    Welcome to the Apple Community.
    Not unless you stop it connecting to wifi at home.

  • Less than 1Mb Upload

    Hello everyone, just got infinity today with the goal of being able to live stream game footage, but I was pretty shocked to find a best upload speed of 0.6Mb (small b is correct, I know the difference).
    I looked around and ran the speed test, clicking the further diagnostic option.  Ideally I kind of need at lest 3Mb upload so am hoping I will be able to achieve that some how.
    My PC is connected via cat5 to the router, and the pc itself is very powerful, 4.2Ghz i7 etc so I know it is not an issue with me having a slow computer.
    Here are the results of the speed test.
    I am happy enough with the download but as you can see something is seriously wrong with the upload. Not sure what to do, would appreciate any help. Thanks.

    This test was run on a wireless connection, however I have also run the test on wired. This usually results in a very marginal increase in download speed, but absolutely no change in upload speed.

  • Speed since upgrade is less than 1MB

    I upgraded to the new faster option 2 speed yesterday, before I was getting 37 down and 6.5 up, now I am getting as below...
    [URL=http://www.speedtest.net][IMG]http://www.speedtest.net/result/1903741730.png[/IMG][/URL]
    Anyone know why?

    General advice is:
    In order:
    Turn OFF your Home Hub
    Turn OFF your Router
    Wait a few minutes
    Turn ON your router and wait for all lights to stabilise green
    Turn ON your Home Hub and wait for all lights to stabilise
    Re-run the speedtest at http://speedtester.bt.com/
    This has resolved the issues you have raised on many occasions. Sadly not mine though LOL.
    UKD

  • The initial heap size must be less than or equal to the maximum heap size.

    All,
    Please help!!
    I have tested my Application Client Project in WSAD on my pc and it works fine.
    I have 1gb RAM on my pc. When I deploy the same app on another xp pc(same as mine but 512mb RAM) I get a heap size error. Here is the exact error:
    Incompatible initial and maximum heap sizes specified:
    initial size: 268435456 bytes, maximum heap size: 267380736 bytes
    The initial heap size must be less than or equal to the maximum heap size.
    The default initial and maximum heap sizes are 4194304 and 267380736 bytes.
    Usage: java [-options] class [args...]
    (to execute a class)
    or java -jar [-options] jarfile [args...]
    (to execute a jar file)
    where options include:
    -cp -classpath <directories and zip/jar files separated by ;>
    set search path for application classes and resources
    -D<name>=<value>
    set a system property
    -verbose[:class|gc|jni]
    enable verbose output
    -version print product version
    -showversion print product version and continue
    -? -help print this help message
    -X print help on non-standard options
    Could not create the Java virtual machine.
    Press any key to continue . . .
    Here is the batch file that runs my app:
    @echo off
    SET appClientEar=C:\corp\apps\mts\jars\MTSClientEAR.ear
    set JVM_ARGS=-Xms256M -Xmx256M
    set CLIENT_PROPS=C:\corp\apps\mts\jars\medicalclient.properties
    set APP_ARGS=
    call C:\bnsf\IBM\WebSphere\AppClient\bin\launchClientBNSF.bat "%JVM_ARGS%" %appClientEar% "-CCpropfile=%CLIENT_PROPS%" %APP_ARGS%
    @pause
    I have changed the value of Xms and Xmx of JVM_ARGS to different size but I sitll get error. Anyone knows what the problem is. Thanks..

    Don't know why, but the "maximum heap size: 267380736 bytes" value is just slightly less than 256*1024*1024, wheras the reported initial size is equal to that.
    Try setting the initial value to 255MB.

  • How to report only quantities less than zero on a calculated field

    I do not understand why my text will not work when it comes to reporting only 'Missing POs' less than zero, I assume it is because I am using 'int' on some fields?
    Any advice?
    SELECT
    t0.father as 'Parent Code',
    t2.itemname as 'Parent Description',
    t2.frgnname as 'Parent Status',
    t0.code as 'Child Code',
    t1.itemname as 'Child Description',
    t1.frgnname as 'Child Status',
    t0.comment as 'Master',
    cast(t3.onhand as int) as 'Child Uncommitted Stock',
    cast(t3.iscommited as int) as 'Child Committed Stock',
    (cast(t3.onhand as int) - cast(t3.iscommited as int)) as 'Child Free Stock',
    cast(t3.onorder as int) as 'Purchase Orders',
    (cast(t3.onhand as int) - cast(t3.iscommited as int)) + cast(t3.onorder as int) as 'Missing POs'
    FROM
    itt1 t0
    inner join oitm t1 on t0.code = t1.itemcode
    inner join oitm t2 on t0.father = t2.itemcode
    LEFT JOIN OITW T3 ON T3.WHSCODE = T0.Warehouse AND T3.ItemCode = T0.Code
    Where T3.WHSCODE Like '[%0]%' and 'Missing POs' < 0
    ORDER BY
    'Missing POs' asc, t0.father, t0.code
    Many thanks,
    Robin (I will be awarding points on all my outstanding questions shorlty - management time pressure at mo!)

    Try this:
    SELECT
    t0.father as 'Parent Code',
    t2.itemname as 'Parent Description',
    t2.frgnname as 'Parent Status',
    t0.code as 'Child Code',
    t1.itemname as 'Child Description',
    t1.frgnname as 'Child Status',
    t0.comment as 'Master',
    cast(t3.onhand as int) as 'Child Uncommitted Stock',
    cast(t3.iscommited as int) as 'Child Committed Stock',
    (cast(t3.onhand as int) - cast(t3.iscommited as int)) as 'Child Free Stock',
    cast(t3.onorder as int) as 'Purchase Orders',
    (cast(t3.onhand as int) - cast(t3.iscommited as int))
      + cast(t3.onorder as int) as 'Missing POs'
    FROM
    itt1 t0
    inner join oitm t1 on t0.code = t1.itemcode
    inner join oitm t2 on t0.father = t2.itemcode
    LEFT JOIN OITW T3 ON T3.WHSCODE = T0.Warehouse AND T3.ItemCode = T0.Code
    Where T3.WHSCODE Like '%0%' and (cast(t3.onhand as int) - cast(t3.iscommited as int))
      + cast(t3.onorder as int) < 0
    ORDER BY
    (cast(t3.onhand as int) - cast(t3.iscommited as int))
      + cast(t3.onorder as int),t0.father, t0.code

  • Less than a month and its already broken

    Dear BT and Forum users,
    I am not very happy with my BB service right now and have come on here in the hope that I might get more that platitudes and fob offs.
    So...  a few weeks ago my husband finally gave into the sales calls and agreed to have Infinity installed. Our reason - not so much faster internet but in the hope we might get a consistant service.The service we had before that was tempermental at best and we were sick of having to reset the router every other day.  (in hindsight we should have just gone with an alternative ISP).
    It was installed a couple of weeks ago and worked well until last Wednesday, since then the service has been a comedy of errors.  To start with my husband confirmed from the outset that they problem was not coming from inside the house but the customer service operator insisted on booking an engineer.
    We agreed to the Friday morning appointment. I booked the morning off work (using annual leave) and the engineer didn't show up. My husband called at 12.30 (they won't take calls from me as I'm not on the bill) and he was assured the appointment was booked in. Shortly after 1 I took a call at the home to say the "system" had lost the booking and the engineer wouldn't be coming.
    I said I was in all day, he could come now but that was clearly off script and the call centre operative wouldn't enterntain the idea (annoyingly there were 2 BT vans in my neighbourhood that afternoon). Instead they wanted me to rebook another 4 hour appointment. I couldn't stop in Saturday and wasn't going to lose more leave. I said I would discuss the options with my husband. 
    What followed that afternoon was a series of coversations with them, some with me at home and some with my husband at work offering the same options and us giving the same response. I don't know if the operatives weren't talking to each other or didn't understand but it was really irritating. In the end they said they would call my husband at 4pm. They called some time after 5 and said the would try the exchange first and call us Monday morning if they needed to access the property.
    Saturday 8.30 the engineer called to say they were on their way, we had the time so we waited. He arrived and was in the house all of 15 minutes before confirming the problem was in the exchange (all that time wasted for that!). We got a call Sunday to say they needed a new part at the exchange then today my husband got an undecipherable voicemail and a text saying the service will be fixed in the next 72 hours. He has spoken to them this evening and we're still non-the-wiser as now there's a fault further up the line. 
    Whilst all this is going on we have tried to find out if they expect us to pay for the Infinity and BT Vision whilst the services are not working. All they will say is they won't look at refunding losses until the issue is fixed. I realise they can't give us a total but it was a pretty straight forward question - am I paying for this non-service. One operator has said I can have £10 to cover the missed appointment (I value my time and annual leave a little higher).
    In all honestly the loss of internet and BT vision is frustrating but what has really dissapointed me is the lack of customer service. No one in the call centres seem to have a clue what's going on (we've had so many versions of what's wrong) and are too tied to a script. There's no sense of inconvenience - I'm supposed to be ready and waiting for 4 hours at a time but they will fix it sometime in the next 3 day. 
    Right now I'm not even sure its worth waiting to get this fixed.
    I'd love for someone to come on here and fix this for me but I'd settle for a little peer support/shared experience.
    Thanks
    L

    OK, so I was being a little optimisitic. We're back online (yay!) but now the bill is just more of the same. Apparently we have to wait 48 hours before they will tell us how they are adjusting the bill  I understand that they cannot confirm the problem si fixed yet because of some internal policy but they won't even tell us how much they would calculate as of now - a pretty straight forward question. 
    So with that, we threw in the towel... said if they can't asnwer a simple question we were off. Of course when I told then operator this he said he's put me straight through to his boss and then left me on hold for over 20 minutes before I gave up!
    Called back to leaver dept. to be told we have to pay £200 to cancel (funny they could give us that figure pretty easily). I don't know what was said when he signed up but I am going to be investigating this further. We've had the service less than a month and its been broken a week.

Maybe you are looking for

  • Hi, does someone know if I can use two Apple tv's with the same iTunes library? Thanks

    Hi, does someone know if I can use two Apple tv's with the same iTunes library? Thanks

  • I need to turn off imessage from my computer

    I recently lost my Iphone 5S and my imessage was on. I switched to my old Galaxy S3 but now I can't receive my iphone users text messages because they are going to my old Iphone that was lost. How can I turn off the imessage from a laptop? Please hel

  • Mouse pointer freezes sometimes

    Whenever I unplug my iPod (shuffle) from the keyboard (of course after having the volume unmounted), some seconds later the mouse pointer freezes and the computer is totally unresponsive for some seconds. Then everything is normal again, i.e. the mou

  • String type field in datasouce from db connect system

    i have create a datasouce from db connect witch connect to a oracle database. and there is a field with type string. when i active transfer rule between infosouce and datasouce it return a error: more than 3 sting type in rule so i hide some field wi

  • Process Loss in Subcontracting Scenario

    Dear all, In this scenario I am sending 10 kg of mat A 10 kg of Material B  to Subcontracting vendor to get a final product of C but in actual process the vendor loss 1 kg of Mat A and 2 kg of material B and final product is of 17 kg .My question is