Load balancing multiple SSO mid-tier with single SSO database
I want to load balance SSO middle tier servers and have them access a single SSO database. When you install infrastructure and select SSO only it creates a new infrastructure database. How can I install multiple SSO servers and point them to a single database. I am doing Load Balancing with F5 and read an Oracle WP where they mentioned an Oracle supported configuration where they load balanced SSO servers with F5.
KB
Two possible solutions:
1.) Oracle 10gAS Enterprise Deployment Guide (B13998-03) follow the configuration for SSO configuration in Chapter 5.
2.) I have not tried this but it should be logically possible with the SSO. 10gAS Administrators guide (B13995-05) Part III Advanced Administration. The success of this method assumes you have OID and SSO each installed in separate homes. You would be cloning the SSO home to another box as if it were a middle tier (it is still part of the infrastructure) then re-configuring it on the new box.
Personally solution 1 is the best method. We are using F5 Big-IP with this configuration and it is working great.
Hope this helps!
Similar Messages
-
Does anyone have a recommended network, hardware and software configuration guide for a Portal installation running with multiple gateways load balanced (ie one URL) that talk to multiple servers?
David,
We've used Resonate (software) to load balance the gateways. It allows
you to group all the gateways under 1 virtual URL and load balance the
incoming connections over each gateway depending on the rules that you
define in Resonate. Look in the SUN portal whitepapers there is one that
talks about it specifically.
As far as load balancing the calls to the portals, the gateways will
automatically load balance across all the portals that they know about
using a simple round-robin rotation. You may be able to use Resonate in
front of the portals but you may need to activate persistance within
Resonate to ensure that the user always ends up on the portal that he
established his initial connection on (if you want that), check with Sun
on this one.
David Broeren wrote:
Recommended configuration for load balanced Portal with load balancer,
multiple gateways and multiple servers.
Does anyone have a recommended network, hardware and software
configuration guide for a Portal installation running with multiple
gateways load balanced (ie one URL) that talk to multiple servers?
Try our New Web Based Forum at http://softwareforum.sun.com
Includes Access to our Product Knowledge Base! -
Load balance multiple URLs on single VIP
Hello,
I have a fairly typical load balance configuration on a pair of ACE appliances running (A3)2.5 and now I need to load balance multiple URIs to these same servers on port 80 to the one VIP. Can someone direct me to a doc that shows a good example of this, or explain it below?
Thanks,
Dave
serverfarm host application
rserver webserver1 80
probe server-80-PROBE
inservice
rserver webserver2 80
probe server-80-PROBE
inservice
sticky ip-netmask 255.255.255.255 address source application-80-STICKY
replicate sticky
serverfarm application
class-map match-all application-80-CLASS
2 match virtual-address 1.1.1.1.1 tcp eq www
policy-map type loadbalance first-match application-80-POLICY
class class-default
sticky-serverfarm application-80-STICKY
insert-http X-Forwarded-For header-value "%is"
class application-80-CLASS
loadbalance vip inservice
loadbalance policy application-80-POLICY
loadbalance vip icmp-reply
nat dynamic 22 vlan 424
appl-parameter http advanced-options CASE_PARAMSean,
Maybe a little confused.
I have built the new serverfarm, policy-map and class-map in bold, I am just not sure how it gets referenced. Do I add it to the multi-match class statement? My complete config for this particular app is below.
Thanks,
Dave
serverfarm host application-80
rserver server1 80
probe server-80-PROBE
inservice
rserver server2 80
probe server-80-PROBE
inservice
serverfarm host application-L7
rserve rserver1 80
probe server-80-PROBE
inservice
rserver server2 80
probe server-80-PROBE
inservice
class-map match-all application-80-CLASS
2 match virtual-address 1.1.1.1 tcp eq www
class-map type http loadbalance match-any application-L7-CLASS
3 match http url /uri1/
4 match http url /uri2/uri2
5 match http url /uri2/uri3.htm
policy-map type loadbalance first-match application-80-POLICY
class class-default
sticky-serverfarm application-80-STICKY
insert-http X-Forwarded-For header-value "%is"
policy-map type loadbalance first-match application-L7-POLICY
class application-L7-CLASS
serverfarm application-L7
policy-map multi-match POLICY-424
class application-80-CLASS
loadbalance vip inservice
loadbalance policy application-80-POLICY
loadbalance vip icmp-reply
nat dynamic 22 vlan 424
appl-parameter http advanced-options CASE_PARAM -
Load balancing multiple J2ee servers - each running it's own CI
Is it possible to load balance multiple J2ee servers(running Portal), both running it's own Central Instance?
We do not have the resources (SAN storage) to implement MSCS for Portal...so instead we want to use two complete Portal servers HW load balanced with the ability to keep running in case one fails.
thanks for any info !
LinwoodHi Linwood,
in a nutshell, the difference between an ordinary J2EE server instance and the central instance are the central services. The central services (enqueue server, message server) are only needed once. Basically, they are required for the communication between the server instances (and to the load balancer). What you should go for is a cluster installation with one central instance and another ordinary server instance (both running the SAP NetWeaver Portal). But be aware that you have to use the same database for both server instances (otherwise you cannot guarantee consistent data).
For load balancing the two server you can use the SAP Web Dispatcher or any other load balancer tool you like.
You will find more and detailed information on load balancing in the SAP Library. Have a look into section <a href="http://help.sap.com/saphelp_nw2004s/helpdata/en/2e/611724f410254ca12a3f396ec5ae85/frameset.htm">Java Cluster Architecture</a>.
Hope I could help!
Best regards,
Martin -
Using a single CSS to load balance multiple services
Is it possible to use a single CSS to load balance 3 different services (server farm) ? That mean the CSS need to advertise 3 VIP
I'm thinking of two scenarios:
1 - configure the CSS to use 4 interfaces: 1 to public, 3 to private (each interface will plug-in to a different vlan/server farm)
2 - configure the CSS to use 2 interfaces: 1 to public, 1 to private (all 3 server farms are in the same vlan)
Will both scenarios work ?
Thanks
--Phillip.Hi Phillip,
both scenarios will work. One CSS can certainly manage more than 3 services! You can even use just one VIP for all traffic, then just create the proper rules to send specific traffic to the corresponding service(s). No need for 3 VIPs.
Regards
-juerg -
CSS10500 Load Balancing Multiple Hosts
Hello,
I have a CSS10500 switch and i would like to load balance the connections to a couple of hosts. My setup (roughly) is as follows
int e1-RTR1-------->int e2-Host1
-------->int e3-Host2
and
int e5-RTR2------>int e6-Host1
------>int e7-Host2
How can i assing different interfaces to the two sets of hosts??? I want all ports (0-65535 and tcp/udp) to go to both sets. I made a circuit vlan 1 and assigned it an ip address but i cannot make a circuit vlan 2 and when i assign multiple addresses to vlan1 i cannot somehow assign interfaces to each ip.
Is there anything i can do??
Sorry for all the fuss i am new to the CSS concept.Let's start with the basic
http://www.cisco.com/en/US/products/hw/contnetw/ps792/products_configuration_example09186a008009438d.shtml
If you can't make it work, get back to us with whatever you have configured.
Verify that you can ping the CSS from the router and the server.
Gilles. -
What's the best way to load balance multiple protocols on one vserver?
Hi,
We have a CSM blade on a 6513, in bridge mode. I'm just wondering what is the best way to serve HTTP and HTTPS (or any two or more ports) from the same group of servers. As I see it, we have two options:
1. Don't set a port on the vserver, so it is load balancing "any" or "tcp". This is easy but I want to be sure there isn't a downside to this, other than the obvious security issue.
2. Create multiple vservers and point them at the same serverfarm. I tried this and I got some odd results with the health checks.
Any ideas? Thanks a lot.you listed the only 2 options available.
The advantage of solution #2 is that you can apply specific config for each protocol ie: for HTTP you can turn 'persistent rebalance' if needed.
If you want to use specific probes [not icmp], it is also a good practice to create a different serverfarm for each protocol.
Like this, if the HTTP service goes down but not the server, you can still have other protocols loadbalanced.
Regards,
Gilles.
Thanks for rating this answer. -
How can I design Load Balancing for distant Datacenters? without single point of failure
Dear Experts,
We are using the following very old and passive method of redundancy for our cload SaaS but it's time to make it approperiate. Can youplease advise:
Current issues:
1. No load balancing. IP selection is based on primary and secondary IP configurations. If Primary fails to respond, IP record for DNS changes to secondary IP with TTL=1min
2. When primary server fails, it takes around 15 min for clients to access the servers. Way too long!
The target:
A. Activate a load balancing mechanism to utilized the stand-by server.
B. How can the solution be designed to avoid single point of failure? In the previous example, UltraDNS is a single point of failure.
C. If using GSS is the solution, how can it be designed in both server locations (for active redundancy) using ordinary DNS server?
D. How can HSRP, GSS, GSLB, and/or VIP be used? What would be the best solution?
Servers are running ORACLE DB, MS SQL, and tomcat with 2x SAN of 64TB each.Hi Codlick,
the answer is, you cannot (switch to two web dispatchers).
If you want to use two web dispatchers, they need something in front, like a hardware load balancer. This would actually work, as WD know their sessions and sticky servers for those. But remember you always need a single point for the incoming address (ip).
Your problem really is about switchover groups. Both WD need to run in different switchover groups and need to switch to the same third software. I'm not sure if your switchover software can handle this (I'm not even sure if anyone can do this...), as this means the third WD needs to be in two switchover groups at the same time.
Hope this helps,
Regards,
Benny -
Load balancing multiple AP1242
Hi,
I just deployed a few AP1242 in my office environment.
I've set them to use the same SSID and encryption (WPA2).
I would like to know can I set load balancing on the APs? E.g. there are 30 users at the office and I installed 2 APs in the area, is there anyway the AP will auto loan balance between themselves, taking 15 users each?
Thanks.Hi Patrick
There really is no load balancing feature with Autonomous AP's. But you can use this;
To allow only so many users to associate to an AP at one time you can use the max-Associations command.
This example shows how to:
Name an SSID
Configure the SSID for RADIUS accounting
Set the maximum number of client devices that can associate using this SSID to 15
Assign the SSID to a VLAN
AP# configure terminal
AP(config)# interface dot11radio 0
AP(config-if)# ssid batman
AP(config-ssid)# accounting accounting-method-list
AP(config-ssid)# max-associations 15
AP(config-ssid)# vlan 3762
AP(config-ssid)# end
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_guide_chapter09186a00802085c4.html
To find out how many users are associated to an AP, this example shows how to display all client devices associated with the access point:
AP# show dot11 associations client
http://www.cisco.com/en/US/docs/wireless/access_point/12.3_4_JA/command/reference/cr34main.html#wpxref81339
Hope this helps!
Rob -
Load Balancing Oracle BI Presentation Server with OC4J
Hello All,
Is there a way to perform Load Balancing Oracle BI Presenation Server the way we do with IIS (defining in ISAPIConfig.XML file)?
I am looking some pointers towards Clustering/Load Balancing Oracle BI Presentation Servers using OC4J not IIS.
Thank you.Thanks , the Oracle BI Presentation Server is running now ,but still the oc4j display the below error :-
C:\OracleBI\oc4j_bi\bin>oc4j.cmd -start
Starting OC4J from C:\OracleBI\oc4j_bi\j2ee\home ...
10/05/06 13:58:31 Error initializing server: /C:/OracleBI/oc4j_bi/j2ee/home/conf
ig/server.xml, Fatal error at line 1 offset 1 in file:/C:/OracleBI/oc4j_bi/j2ee/
home/config/server.xml: .<Line 1, Column 1>: XML-20108: (Fatal Error) Start of r
oot element expected.
10/05/06 13:58:31 Fatal error: server exiting -
Is there any failover/load balancing among kjs engines on a single ias server?
I guess the question pretty much says it all. To be more explicit, if a kjs engine crashes, would all requests in progress be re-attempted on a different kjs?
Also, at what level is the user session information stored (kjs, kxs)?
Thanks a lothi Mihai,
Yes, we do have a load balancing mechanism between the KJSs in a single instance of the appserver. Requests from the kxs engine will be load balanced in a round robin fashion to the KJS engines.
Note that if a KJS engine crashes, then the requests will be directed to the other KJS engines, but if the KJS engine is 'hanging', then this redirection does not happen.
If the sessions are distributed, then they are stored in the KXS, but if they are lite, then they are stored in the KJS engine.
Hope that helps,
Vasanth -
Rel 2 Mid-Tier with Rel 1 Infrastructure?
We installed AS/10g Release 1 (9.0.4), with Mid-Tier on one server and Infrastructure on another. Is it possible to install Release 2 (10.1) Mid-Tier using the Rel. 1 Infrastructure?
Krrish,
So do you mean that the BPEL respository was already there when you did the install? If yes, then that explains the mismatch error. You should always clean up the old references if doing a reinstall. Drop the user and schemas related to PM and do a reinstall.
--Shiv -
Load Balancer virtual URL not working with analytics page
We have configured Load Balancer virtual URL. But it is working for only iAS. We have Oracle Application Server 10.1.3
Our OBIEE is 10.1.3.4.1
Here is the virtual configuration
Listen 7877
+<VirtualHost default:7877>+
+# General setup for the virtual host+
DocumentRoot "/apps_base/obiee/ias/Apache/Apache/htdocs"
ServerName uat.bi.company.com
ServerAdmin [email protected]
ErrorLog "|/apps_base/obiee/ias/Apache/Apache/bin/rotatelogs /apps_base/obiee/ias/Apache/Apache/logs/error_log 43200"
TransferLog "|/apps_base/obiee/ias/Apache/Apache/bin/rotatelogs /apps_base/obiee/ias/Apache/Apache/logs/access_log 43200"
Port 443
+# SSL Engine Switch:+
+# Enable/Disable SSL for this virtual host.+
SSLEngine on
https://uat.bi.company.com -> WORKS great
https://uat.bi.company.com/em -> WORKS great
https://uat.bi.company.com/analytics -> page cannot be displayed
We have SSO configured. So i do get the SSO login page, but clicking on submit button, I get page cannot be displayed.
Everything works if I disable the load balancer virtual.
THe Load Balancer is configured to listen on 443 and then routes to 7877 on the physical server coorldas04.company.com
Can you assist in this one ??Is this still a problem?
-
Disable load balancing on dual PRIs - 3640 with MICA modems for dial out
We have a custom application that connects through reverse telnet to a Cisco 3640 that has 2 NM-24DM modules and 2 PRIs connected to it. Currently all outgoing calls are getting load balanced over the two PRIs. I need to change that so that all calls go over the first PRI and when all channels are used up, it starts using the second PRI. Seems like a simple enough thing to do but I can't figure out how to.
Here is my config
Current configuration : 1401 bytes
version 12.4
service timestamps debug uptime
service timestamps log uptime
service password-encryption
hostname DIALOUT01
boot-start-marker
boot-end-marker
enable secret 5 xxxxxxx
no aaa new-model
clock timezone EST -5
clock summer-time EDT recurring
no ip routing
no ip cef
no ip domain lookup
ip domain name xxxxxxx.xxx
isdn switch-type primary-ni
controller T1 0/0
framing esf
linecode b8zs
pri-group timeslots 1-24
description xxxx
controller T1 0/1
framing esf
linecode b8zs
pri-group timeslots 1-24
description xxxx
interface FastEthernet0/0
ip address dhcp hostname dialout01
no ip route-cache
no ip mroute-cache
duplex auto
speed auto
interface Serial0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
no fair-queue
no cdp enable
interface Serial0/1:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
no fair-queue
no cdp enable
no ip http server
control-plane
line con 0
line 33 56
modem InOut
modem autoconfigure type mica
transport preferred telnet
transport input telnet
transport output telnet
line 65 88
modem InOut
modem autoconfigure type mica
transport preferred telnet
transport input telnet
transport output telnet
line aux 0
line vty 0 4
password 7 xxxxx login
end
Thanks,
ShahidIf I understand the question I think that isdn bchan-number-order is the command you are interested in. I think it detaults to round-robin, sounds like you want ascending (that is isdn bchan-number-order ascending). It is an interface subcommand.
See http://www.cisco.com/en/US/docs/ios/12_3t/12_3t2/feature/guide/gt_ibcac.html#wp1055853
That may only apply to native ISDN calls and not MICA based calls, but see if that helps. -
Load Balancing multiple web servers
Hi All:
I need to load balance 2 different web servers using sticky connections on a LocalDirector 416.
I need to use cookie-passive mode, which of course relies on a cookie set by the web server.
Problem: The name of the session cookie is different on each web server (IIS) and I'm not sure that I can change it.
Question: What do I pass to the sticky command as the name of the cookie?
Any ideas?
craigfortunately the cookie are different on the 2 servers otherwise this feature would not work.
The value you enter after the keyword cookie-passive is a 'name' and can be whatever you want (you can also leave it blank/empty).
The LD will learn the cookie directly from the server.
See the documentation at :
http://www.cisco.com/univercd/cc/td/doc/product/iaabu/localdir/ldv42/421guide/42ch05.htm#xtocid8565101
I hope this answer your question.
Gilles.
Maybe you are looking for
-
[REQ] vBios - R9 290X Gaming 4G
Hi, I would need an updated bios for my R9 290x Gaming 4G. S/N: 602-V308-01SB1402008429 Current bios: h**ps://drive.google.com/file/d/0B7z08TYJKYPfN0JDdWZna2EtV28/view?usp=sharing Thank you!
-
Call Z rfc from SUP2.1 mbo
Hi all I have created a custom FM to return the rows from a custom table. When creating my MBO, everything works as expected. When I run the workflow application I get the following error. Error getting SAP function template for [ZGETTABLE] Using a s
-
HI i CREATED A PROCEDURE IN REPORT NAME P_SUPPLIER THIS PROCEDURE WILL RETURN VALUES ('ZEG','ZUS'); AND PASSING VALUES TO PARAMETER P_SPLR PROCEDURE P_SUPLR IS SUPPLIER VARCHAR2(2000); BEGIN SELECT DISTINCT(M.SPLR) INTO :P_SPLR FROM DM_MARKETING M WH
-
Folder-Naming when organizing photos on an external location
Hi By now I use to organize my photos in the internal aperture libary. Since Aperture 1.5 has the possibility to save the photos itselfs in an seperate folder on the filesystem i fiddled around with this option a little bit. It's a nice option. But t
-
Help...how do I reset "Designer View" to what shipped with product. I was using a tutorial and totally messed up the designer default view, and cannot restore it by going to workspace "Designer View" reset...it just resets it to the same corrupted v