Measurement point -PM

I need to add new reading to a measurement point using RFCs/BAPIs or some code.
Please suggest how I can do it.
In our requirement, there is an order. It has Functional location attached to it. This Functional location has measurement points.
I need to add new reading (or say need to create new measurement document) against the measurement point. And this new measurement document should be saved against orderId.
Please help.

Hi,
there are lot of RFCs as below. If anybody feel any RFC could be helpful to me for my requirement.
MEASUREM_BUFFER_GET_DELTAS
MEASUREM_BUFFER_INITIALIZE
MEASUREM_CHECK_TRANSFER_POINTS
MEASUREM_COPY_CHAIN_EXPLODE
MEASUREM_COPY_CHAIN_EXPLODE_TR
MEASUREM_COPY_CHAIN_FIND_ROOT
MEASUREM_COPY_CHAIN_TIME_RANGE
MEASUREM_COUNTER_COPY_INTERVAL
MEASUREM_DIALOG_CANCEL
MEASUREM_DIALOG_UPDATE
MEASUREM_DOCUM_AFFECTED_INTVLS
MEASUREM_DOCUM_ARRAY_DIAL_BUF
MEASUREM_DOCUM_CANCEL_ARRAY
MEASUREM_DOCUM_CANCEL_TO_ORDER
MEASUREM_DOCUM_DIALOG_LIST
MEASUREM_DOCUM_DIALOG_LIST_1
MEASUREM_DOCUM_DIALOG_SINGLE
MEASUREM_DOCUM_IMTR_CLEAN_UP
MEASUREM_DOCUM_INTERVAL_SPLIT
MEASUREM_DOCUM_LIST_PAI
MEASUREM_DOCUM_LIST_PBO
MEASUREM_DOCUM_READ_DIALOG_BUF
MEASUREM_DOCUM_READ_LAST_BUF
MEASUREM_DOCUM_RFC_SINGLE_001
MEASUREM_DOCUM_RFC_SINGLE_002
MEASUREM_DOCUM_STORE_PREFETCH
MEASUREM_DOCUM_TAKE_UP_COPYING
MEASUREM_FCODE_PROCESS
MEASUREM_OBJECT_REMOVE_BUFFER
MEASUREM_OBJECT_SWITCH_NUMBER
MEASUREM_OK_CODE_IMPORT
MEASUREM_ORDER_SWITCH_NUMBER
MEASUREM_POINTS_COPY_TO_OBJECT
MEASUREM_POINT_ARRAY_DIAL_BUF
MEASUREM_POINT_DIALOG_LIST
MEASUREM_POINT_DIALOG_SINGLE
MEASUREM_POINT_ENQUEUE_ARRAY
MEASUREM_POINT_F4_BY_OBJECT
MEASUREM_POINT_READ_DIALOG_BUF
MEASUREM_POINT_REMOVE_BUFFER
MEASUREM_POINT_RFC_SINGLE_002
MEASUREM_POINT_STORE_PREFETCH
MEASUREM_POINT_UPD_PYEAR
MEASUREM_DOCUM_CONV_INPUT
MEASUREM_DOCUM_CONV_OUTPUT
MEASUREM_DOCUM_READ
MEASUREM_DOCUM_READ_FIRST
MEASUREM_DOCUM_READ_INTERVAL
MEASUREM_DOCUM_READ_LAST
MEASUREM_DOCUM_READ_NEAREST
MEASUREM_DOCUM_READ_TO_ORDER
MEASUREM_IMRCCUST_READ
MEASUREM_OBJECT_LAST_DOC
MEASUREM_POINTS_READ_TO_OBJEC
MEASUREM_POINT_ARRAY
MEASUREM_POINT_ARRAY_BY_POINT
MEASUREM_POINT_CALL
MEASUREM_POINT_CONV_INPUT
MEASUREM_POINT_CONV_OUTPUT
MEASUREM_POINT_IMPH_ARRAY
MEASUREM_POINT_READ
MEASUREM_POINT_READ_IRFMP
MEASUREM_POINT_USAGE_OF_ATINN
MEASUREM_POINT_DIMENSION_CHECK
MEASUREM_POINT_LAST_VALUE
MEASUREM_POINT_F4_BY_BUILDING
MEASUREM_POINT_F4_BY_EQUIPMENT
MEASUREM_POINT_F4_BY_FUNC_LOC
MEASUREM_POINT_F4_BY_OBJECT_G
MEASUREM_POINT_F4_BY_RNTL_UNIT
MEASUREM_ENTRYLIST_CHANGE
MEASUREM_ENTRYLIST_CREATE
MEASUREM_ENTRYLIST_LAST_DOC
MEASUREM_ENTRYLIST_READ_DB
MEASUREM_DOCUM_GRAPHICS
MEASUREM_COPY_CHAIN_REPORT_01
MEASUREM_COPY_CHAIN_REPORT_02
Thanks
Edited by: Rohit Kumar on Oct 14, 2008 12:40 PM

Similar Messages

Function Modules for creation of characteristics and Measurement Points

Hello everybody
I'm new in ABAP (trainee) and especially the use of characteristics. I'd be very happy if somebody could help me :).
Can anybody out there with some experience in creating characteristics and measurement points tell me how to create them with function-modules or by changing database tables?
I'm happy about every hint and ready to give some reward points.
Best Regards,
Steffen

FM and TABLES
http://72.14.235.104/search?q=cache:71IXBMWcX_8J:reflexcontracts.co.uk/SAP_R3_QUICK_REF.xlsupdatetable+tse05&hl=en&ct=clnk&cd=1&gl=in
FUNCTION MODULES
http://www.erpgenie.com/abap/functions.htm
http://www.sapdevelopment.co.uk/fmodules/fmssap.htm
http://www.erpgenie.com/abap/index.htm
http://www.geocities.com/victorav15/sapr3/abapfun.html
Rewards if useful..........................
Minal

Triggering of Preventive Maintenance based on Measuring Point

Hi,
I have set measuring point & defined upper range limit and lower range limit. Now I want to trigger preventive maintenance, based on reading enter against measuring point specifically if measuring point reading is above or below defined upper range limit or lower range limit.
Letu2019s say example, If 10 and 5 is upper range limit and lower range limit, now in this case creation of notification / main order if user has enter measuring point value more than 10 or less than 5.
Regards,
Dipen Shroff

Hi,
You can do it via Condition Based Maintenance ..
IMRC0001- U can use this User exit
http://help.sap.com/erp2005_ehp_04/helpdata/EN/a7/fa4c988f6611d29e8a0000e8323350/frameset.htm
regards
pushpa

Auto Update of measuring point/document

Dear all,
I have one issue over here.Measuring point/document is not updating automatically after productiuon order confirmation . I tried with following steps
1) Created the equipment as test equipment -->created measuring point as a counter ---> maintain the usage value formula SAPF02 in the PRT tab . Unit of measurement for the characteristics and base unit of measure of material are same
2) Then i have assigned this eqipment as a PRT in the routing of material .
Which steps i am missing
Thanks

Hi
I had faced the same problem when I used SAPF02 then I did following changes.
Created formula like SAP_09 * PRTSTD / SAP_08
SAP_09 : Operation Qty
PRTSTD : PRT Standard Value
SAP_08: Base Qty.
Also make sure the measuring point category should me T in IK02( PRT life counter)
Regards,
Raj

Maintenance Order through Measuring Point

Dear all,
I want to know whether it is possible to create the maintenance order on the basis measuring point .
I know how to create the order on the basis of measuring counter.
Is there any procedure to create the maintenance Order through measuring point as done in case of counter?
kindly provide the solution for Creation of Maintenance Order using Measuring Point..

Really very thanks for the solution.
I have one more query, we can create the measuring point using the t.code IK01.As you told we have to create the measuring point with upper and lower range.
Is that we have to create 2 measuring point for upper as well as lower range or in one measuring point it is possible to accumulate both the upper and lower range.
If it is possible to accumulate both the upper and lower range in one measuring point then kindly provide the procedure.
Thanks in advance.

Measuring Point Status.

Dear All Consultants,
I have scenario for warranty services, so I define master warranty with to conditions years - kilometer reading.
The problem is while assigning master warranty to equipment master system gives me this error {could not determine the status for measuring point 000000000212 at date 11.06.2007
Message no. BG212 }
Why this message appears and how to solve it.
It is only warning message but it assume that the warranty expired.
Waiting your kindly replay.
yasser.

Hi,
Please refer the link below
http://help.sap.com/saphelp_46c/helpdata/en/5a/3efb377409bd5ae10000009b38f889/frameset.htm
as you might have not defined first counter.
Enjoy SAP
Dont forget to give points if its useful ans.
Namskar
Ketan Dave

Cannot create "Digital" measuring points on Work Manager 6.0

Hi All,
I am attempting to create "digital" i.e. Pass/Fail measuring points in Work Manager 6.0. I can enter readings as shown below but when I execute a sync, the error message below is shown:
I can use the same measuring point in SAP via IK11 as shown below to create a measuring document using valuation code only. However, the Work Manager requires a numeric characteristic to be added and the "no reading" checkbox to be ticked.
Any help would be greatly appreciated.
Thanks,
Jonathan

Hi Michael,
I tried setting it up with just the two values (0-fail and 1-Pass) and I'm still running into errors. If you could take a look I'd be grateful.
Set up code group with two values:
IK11 allows just the valuation code to be used:
On the device:
As far as I can see this should work but it still creates the same error as previously. Ideally it should work as IK11 and allow the user to select from multiple valuation codes but it appears to still require a characteristic.
One option I tried is to assign a characteristic in addition to the the valuation code and use a 0 reading. This works but is a "workaround" solution in comparison to IK11.
Any help would be really appreciated.
Thanks,
Jonathan

Screen enhancement in display measuring point (ik07) and ik02

Hi experts,
Can anybody please help in determining userexits for screen enhancement of ik02 transaction. I need to add block to measuring point details.
and also i need selection screen input parameters to display at the bottom of ik07 tcode.i had inserted the selection screen parameters at the top of screen in ik07 but i need it at last. how can it be inserted there.
PLZ HELP!!
screen shot of ie02 for referenece....

Hello Jared,
Have a look to this :
http://help.sap.com/saphelp_crm50/helpdata/en/20/a4ffee7e0fcc4ebb7e5466d3903d38/frameset.htm.
Regards,
Frédéric

How to make Measuring Point Description Field scrollable on the Detail Read Screen

In the Measuring Point Read Detail Screen (Rounds Manager), the description field does not have a scroll bar like it does on the Point Read Counter Detail Screen. This means that the end-user has to arrow-over to the right on the handheld device to see the entire description. We changed the transaction property to be the same as that on the measuring point field on the Counter screen but that did not resolve the issue. We are assuming that the field width is defined in columns but are not sure if columns is the same as pixels. It seems like there is some type of behind the sceens calculation based on the number of pixels used by the characters in the description. The transaction property does have word wrap activated but it seems to make no difference. Does anyone have any suggestions on what can be done to make the measuring point description have a scrollbar and have the description wrap? The Rounds Server is version 2.3.
Tags edited by: Michael Appleby

1. wall of unformatted code. Use \ tags when posting code.
2. you're not even asking a question. You're just saying "it doesn't work" and then you dump the code. What do you expect? That people now go to debug it for you?

Measuring Points are Not displaying in mobile devices(SAP WM 6.1)

Hi Experts,
In mobile devices the measuring pints for work order not displaying. When we select the "record point" option for particular work order it should display the measuring points for that WO. But it displaying '0 measuring points'. As shown in screen shot below.
But in SAP Bach end Measuring Documents are defined for Work Order.
can any one explain :To display measuring points in mobile devices, need any extra configuration in back end? or
What functionality need to activate? How to enable this?
Thanks
Chigari

Hi Chigari
Measuring Points assigned as PRT's in backend application (SAP ECC) should be displayed in Agentry Work Manager 6.1 by standard, if their corresponding technical objects are assigned to either the Work Order header or one of the operations.
Please check if this requirement is fulfilled in your case.
There is no need to modify anything in the Configuration Portal (as far as I know).
The modification we have made is only regarding Measuring Points belonging to other Technical Objects (and still assigned as PRTs).
Søren Hansen

Making system settings for measurement documents and measuring point

What is the significance of making system settings for measurement documents and measuring point in spro?
Edited by: Pallavi Kakoti on Jul 14, 2011 1:23 PM

Hi,
<< Moderator message - Cut and paste response from http://www.consolut.com/en/s/sap-ides-access/d/s/doc/YY-OLI0IMRCCUST removed. Plagiarism is not allowed in SCN >>
Regrds
Jitender
Edited by: Rob Burbank on Jun 6, 2011 10:53 AM

Function Module to get usage by supplying measuring point and equipment no

Hi,
I want to know what is the function module to get the usage on giving the measuring point,equipment number and month.Thanks in advance.
Regards,
SGR

Try this Function Module : ALM_ME_EQUIPMENT_GETDETAIL

Relation between notification no and measuring point no or document

Dear Expert's
I want to link between notification no (qmnum) and measuring point no or measuring point document.
I want to search measuring point number thorough notification no.
plz suggest me ABAP purpose.
thanks.
regards:
Neelesh Sonkar

Hi,
1. Get the EQUNR from the table "QMIH" using QMNUM.
2. Get the MOVING_OBJECT from the table "IEQT_WL_MP" using EQUNR.
3. Get the MDOCM (Measurement Document) POINT (Measuring Point) from the table "IMRG"
using MOVING_OBJECT ( which is MDOCM ).
Hope this will help you.
Regards,
Smart Varghese

Update Measurement Points on Functional Locations

Hello Experts,
I need create a custom program to update (add/delete/change) the measurement point's POSITIONS on functional locations. Basically the users want to clean up the functional locations which have some wrong data in them. Since I am very new to this functionality area, Can anybody please let me know - Is there a FM/Bapi to update the Measurement Point Positions on Functional Locations?
I appreciate your help.
Thanks.
Edited by: sey ni on Mar 7, 2011 4:49 PM

I think I will have to write a BDC on IK01/IK02 transactions. Not sure, if we have a better solution.

Copy Measuring Point from 1 FL to other FL

Hi,
I need to copy the Measuring Point( General Data, Counter Data & Classfication) from 1 Func Location to another Func Location.
Please suggest me...
regards,
Venkatesan Anandan

HI,
As suggest Pete, Plese go to IL01 and enter the referece functional location, then press enter
once you press enter pop will appear , where you select measuringpoint, class etc as required by you
then automatically data will transfer to new functionallocation which u creted.
regards
Krishna

Propose Measuring point automatically in IW42

Hi,
I have assigned a measuring point as PRT to the operation of an Order. During confirmation in IW42, after entering the order number system proposes the operation details and I need to click button meas.points Inspn planning to display the measuring point assigned to the operation. But now my requirement is, system should propose the measuring point automatically, along with operation details, when I enter the order number in IW42 as user will forget to click button meas.points Inspn planning.
Could anybody suggest how this requirement can be met?
Thanks and regards,
Basavaraj

Hi James,
Thanks for your reply.
Yes, I have configured confirmation profile and same has been selected in IW42. I can see screen area for measurement document in IW42. Now my requirement is, I want the system to display the measuring point automatically, which is assigned to operation as PRT, when I enter the order number in IW42 ans press enter.
Thanks and regards,
Basavaraj.

Measurement point -PM

Similar Messages

Maybe you are looking for