Minimum IOS version to support scp URLs
While recent IOS versions support scp sources or destinations for copy
operations ...
aprompt#copy running-config ?
flash1: Copy to flash1: file system
flash2: Copy to flash2: file system
flash: Copy to flash: file system
ftp: Copy to ftp: file system
http: Copy to http: file system
https: Copy to https: file system
null: Copy to null: file system
nvram: Copy to nvram: file system
rcp: Copy to rcp: file system
running-config Update (merge with) current system configuration
scp: Copy to scp: file system
startup-config Copy to startup configuration
system: Copy to system: file system
tftp: Copy to tftp: file system
tmpsys: Copy to tmpsys: file system
aprompt#copy running-config
... older ones obviously don't (here we have 12.1):
aprompt#copy running-config ?
bs: Copy to bs: file system
flash: Copy to flash: file system
ftp: Copy to ftp: file system
null: Copy to null: file system
nvram: Copy to nvram: file system
rcp: Copy to rcp: file system
running-config Update (merge with) current system configuration
startup-config Copy to startup configuration
system: Copy to system: file system
tftp: Copy to tftp: file system
xmodem: Copy to xmodem: file system
ymodem: Copy to ymodem: file system
zflash: Copy to zflash: file system
aprompt#copy running-config
Who could tell me the minumum version to support scp URLs?
Thanks and Regards, Thomas
Ideally any feature set questions are answerable in Cisco Feature Navigator (http://www.cisco.com/go/fn).
The Secure Copy (SCP) feature provides a secure and authenticated method for copying router configuration or router image files. SCP relies on Secure Shell (SSH), an application and a protocol that provide a secure replacement for the Berkeley r-tools. So ideally you should be running crypto images (k9) which support SSH and hence SCP as well.
But following are some details about SCP, which may be helpful :
Feature Name
Releases
Feature Information
Secure Copy
12.2(2)T12.0(21)S
12.2(25)S
This feature was introduced in Cisco IOS Release 12.2(2)T.
This feature was integrated into Cisco IOS Release 12.0(21)S.
This feature was integrated into Cisco IOS Release 12.2(25)S.
The following commands were introduced or modified: debug ip scp, ip scp server enable.
Following is details Feature Information for Secure Shell Version 2 Support:
Feature Name
Releases
Feature Information
Secure Shell Version 2 Support
12.2(11)T
12.2(25)S
12.3(4)T
15.3(2)S
The Secure Shell Version 2 Support feature allows you to configure Secure Shell (SSH) Version 2 (SSH Version 1 support was implemented in an earlier Cisco IOS software release). SSH runs on top of a reliable transport layer and provides strong authentication and encryption capabilities. SSH version 2 also supports AES counter-based encryption mode.
The following commands were introduced or modified: debug ip ssh, ip ssh min dh size, ip ssh rsa keypair-name, ip ssh version, ssh.
Secure Shell Version 2 Client and Server Support
12.0(32)SY
12.3(7)JA
12.4(17)
The Cisco IOS image was updated to provide for the automatic generation of SNMP traps when an SSH session terminates.
SSH Keyboard Interactive Authentication
12.2(33)SXH3
12.4(18)
The SSH Keyboard Interactive Authentication feature, also known as Generic Message Authentication for SSH, is a method that can be used to implement different types of authentication mechanisms. Basically, any currently supported authentication method that requires only user input can be performed with this feature.
Secure Shell Version 2 Enhancements
12.2(50)SY
12.4(20)T
15.1(2)S
The Secure Shell Version 2 Enhancements feature includes a number of additional capabilities such as support for VRF-aware SSH, SSH debug enhancements, and DH Group 14 and Group 16 exchange support.
In Cisco IOS 15.1(2)S, support was added for the Cisco 7600 series router.
Note
Only the VRF-aware SSH feature is supported in Cisco IOS Release 12.2(50)SY.
The following commands were introduced or modified: debug ip ssh, ip ssh dh min size.
Secure Shell Version 2 Enhancements for RSA Keys.
15.0(1)M
15.1(1)S
The Secure Shell Version 2 Enhancements for RSA Keys feature includes a number of additional capabilities to support RSA key-based user authentication for SSH and SSH server host key storage and verification.
The following commands were introduced or modified: ip ssh pubkey-chain, ip ssh stricthostkeycheck.
-Thanks
Vinod
**Encourage Contributors. RATE Them.**
Similar Messages
-
Router platform and IOS version to support MPLS
I have few Cisco 2621 routers and one 3640 router, could I use these router to create a MPLS VPN lab? if so , what is the minimum IOS version required?
Thanks in advance.The minimum hardware and software image tu support MPLS can be found at www.cisco.com/go/fn select search by feature and in the search box put MPLS (Multiprotocol Label Switching) there you can find the platform and IOS to support basic MPLS, but you need to consider the fact that supporting MPLS special features like AToM can only be supported on some 7200, 7500, 7600, 10000 and 12000, http://www.cisco.com/en/US/products/sw/iosswrel/ps1839/products_feature_guide_chapter09186a0080153e64.html#1030652
-
Is there a minimum IOS version for windows radius 2012R2
Hello,
We use a windows server 2008R2 and NPS for radius authentication of our 887,881 and 891 routers, ASA V8.4, and 3750 switches.
We are thinking about migrate our radius to windows 2012R2, wich is a new version of NPS.
do you know if there is a minimum IOS version required for NPS on 2012R2 Windows ?
ThanksHi,
Yes NPS will work with Window Server 2012R2 and for the minimum server certificate requirement
check the below link.
http://msdn.microsoft.com/en-us/library/cc731363.aspx -
What is the minimum iOS version that Apple Configurator is supported with?
I have a few very old iPads, not even iPad 2's. I am considering using Apple Configurator to supervise them. What is the minimum iOS these iPads need to be at to supervise the ipad
See the chart below to determine whether you can upgrade your device and what you can upgrade to.
IPhone, iPod Touch, and iPad iOS Compatibility Chart
Device iOS Verson
iPhone 1 iOS 3.1.3
iPhone 3G iOS 4.2.1
iPhone 3GS iOS 6.1
iPhone 4 iOS 6.1
iPhone 4S iOS 6.1
iPhone 5 iOS 6.1
iPod Touch 1 iOS 3.1.3
iPod Touch 2 iOS 4.2.1
iPod Touch 3 iOS 5.1.1
iPod Touch 4 iOS 6.1
iPod Touch 5 iOS 6.1
iPad 1 iOS 5.1.1
iPad 2 iOS 6.1
iPad 3 iOS 6.1
iPad 4 iOS 6.1
iPad Mini iOS 6.1 -
CS5.5 Air for iOs - Which iOs versions are supported?
Hi everyone,
I wanted to test the functionalities of the Cs5.5 exporter for iOS, by exporting a previous Flash game i made on my 2G iPod, with 4.2.1 iOs version installed.
Since i wouldn't want to pay for the iOS developer certificate just for trying, can anyone point out a solution for this?
Moreover, is anyone sure it's gonna work? I wouldn't wanna spend good money just for seeing the Flash exporter is no good for my device.
Suggestions?
Anyone tried on similar OS?
Thanks a lot
IacopoOk, i managed to use a fake certificate (i know i shouldn't say that) just to check the feasability of a game on iOS and.... I found out that the exporter doesn't work on my iPod Touch 2G (iOs 4.2.1)!! It says the iPod is not supported!!
Any news on this?
Do i need to buy an iPhone 5 to test flash games? It sounds a little extreme.... -
Compatible 6500 IOS version to support IDSM-2 Inline mode
The 6500 model WS-SUP720-3BXL with IOS version 12.2(18)SXD4,
and IDS card WS-SVC-IDSM-2 with sw 5.0(2)is compatible to run on inline mode.
Regards,
VirajGood day,
Hi, You need minimum sup-bootdisk:s3223-advipservicesk9_wan-mz.122-18.SXF7.bin IOS to enable INLINE mode on 6500 series.
as per my knowledge,
the latest IOS is
sup-bootdisk:s3223-adventerprisek9_wan-mz.122-18.SXF13.bin.
for IDSM-2, if u upgrade to Engine 2 IOS, U can get update with E2 signatures and also U can manage from New Management Console like Cisco IPS manager Express 6.1.
I hope this will satisfy. -
Cisco IOS Version to Support SIP Trunking on AS5400 Routers
Hi all,
Kindly help .Can anyone tell me which Cisco IOS Version Supports SIP Trunking on AS5400 Routers ?
Regards,
Cliff .Hi,
Please look at:
http://www.cisco.com/en/US/products/hw/univgate/ps505/products_data_sheet09186a0080091e51.html
http://www.cisco.com/en/US/docs/routers/access/as5350/software/feature/guide/UPfeapu.html
HTH
Jorge Armijo
Please remember to rate helpful responses and identify helpful or correct answers. -
IOS version that support 2048 bits certificate
Hello,
I need to update a 2504 Wireless Controller to a version that supports 2048 bits certificates.
I´m checking release notes for release 7.4.110.0 and I don´t see any information about a limitation in certification size (2048 bytes in my case).
Do you know any restriction about the certificate size in this or another version?
Thanks and Regards.
Iván.2048 bit is supported on the WLC. I use it for WebAuth and 3rd party certificates as these vendors only issue 2048 these days.
Sent from Cisco Technical Support iPhone App -
Minimum IOS version for IPS sensor v6 on CAT6500 series
What is the recommended minimum Cisco IOS Software that will support Cisco IPS Sensor Software v6 on the CAT6509
It depends on your Supervisor Engine, MSFC/PFC and capture method.
There's a good IDSM "software and hardware requirements" table here (but better elesewhere on CCO)
http://cisco.com/en/US/docs/security/ips/5.0/installation/guide/hwIdsm2.html
â¢Catalyst software release 7.5(1) or later with Supervisor Engine 1A with MSFC2
â¢Catalyst software release 7.5(1) or later with Supervisor Engine 2 with MSFC2 or PFC2
â¢Cisco IOS software release 12.2(14)SY with Supervisor Engine 2 with MSFC2
â¢Cisco IOS software release 12.1(19)E or later with Supervisor Engine 2 with MSFC2
â¢Cisco IOS software release 12.1(19)E1 or later with Supervisor Engine 1A with MSFC2
â¢Cisco IOS software release 12.2(14)SX1 with Supervisor Engine 720 -
Which iOs version is supported?
Hi
I'm just wondering which version of iOs is supported by the 4.5SDK?
Regards,
Larsi think it comes out in June right now it is Android only someone correct me if i am wrong !
-
Minimum IOS version for SPAN on 2950s
I have a new IDS sensor that we finally have up and running. In attempting to montor one of our 2950 switches we noticed that the monitor command is not an option. Is there a minimum version or platform that has this option? I have found nothing so far in the online docs. This switch is currently running 12.0(5.3)WC(1).
HI Friend,
The code you are running has the SPAn capability but not very advance features are available.
The command is "port monitor
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat2950/2950_wc/cli/cli_cmds.htm#xtocid1856851
Also the feature has limitation that if the traffic on monitoring port exceed 50% it will be a problem.
Check the release notes for more details
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat2950/2950_wc/1169303.htm#xtocid13
I will say to have more better code on your switch to use SPAN in better way something likt this
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat2950/12119ea1/2950scg/swspan.htm
Yiu can have much better codes like 12.1(20)EA1 and higher.
HTH
Ankur -
Minimum SL version that supports SSD?
I have a Mac mini 3,1 running 10.9 on a Samsung SSD 840 128 GB internal SATA drive. It works, but I need to go back to 10.8 until a known bug in 10.9 gets fixed. The base install version of OSX for the mini is 10.6.2, but doesn't include driver support for SSDs so I can't just wipe the SSD with DiskUtility and install 10.6.2 on it. ML didn't come as a full install, only an upgrade. I don't see a clear path to do this...
Is there a way I can get back to 10.8?What you can do is to redownload OS X Mountain Lion from the Mac App Store. Open the Mac App Store, go to Purchases and redownload the OS X Mountain Lion installer.
When the download finishes, use DiskMaker X to create a USB drive or DVD with the OS X Mountain Lion installer. Then, hold the Option (Alt) key while your Mac is starting up and choose the USB drive or DVD.
Open Disk Utility, select Macintosh HD in the sidebar, go to Erase tab and erase the volume. Finally, close Disk Utility and reinstall OS X.
Make a backup of your files manually before formatting the hard drive -
how do i get dictionary application in my iphone 3g running in 4.2.1 ios. and i want skype and viber and facebook as well. could anyone help
Since the iPhone 3G will only run iOS up to 4.2.1, if these apps require a higher iOS level, there is nothing that you can do.
There should be some dictionary apps in the App store that will run on iOS 4.2.1. -
IDSM2 on 6500-IOS inline mode support?
Hi,
I have an IDSM-2 running IPS5.1(1d) software (recently upgraded from 4.x) that is sitting on a 6500 IOS.
The IPS device manager shows gi0/7 and gi0/8 as both in Promiscuous mode. There is no option to change the mode to inline and pair them.
Is it so that IDSM-2 currently supports only Promiscuous mode?
If so, then this module is still acting as an IDS despite running IPS5.1. Isn't it? What is the advantage that I get after upgrading it from 4.x to 5.1?
-- VasanthThere are 2 pieces to the puzzle.
There is the IDSM-2 version and what it supports, but also the Cat 6K Native IOS version and what it supports.
IDSM-2 v5.1(1d) supports
a) Promiscuous mode,
b) InLine Interface Pair mode (2 interfaces are paired for inline monitoring), and also
c) InLine Vlan Pair mode (2 vlans on a single interface are paired for inline monitoring, you will also see it called inline-on-a-stick)
But for these features to be used, the switch code must also support configuring the switch side of the IDSM-2 for each of these 3 features.
Native IOS Versions prior to 12.2(18)SXE will support only Promiscuous mode on the IDSM-2.
12.2(18)SXE and later versions will support InLine Interface Pair mode on the IDSM-2.
No Native IOS versions currently support InLine Vlan Pair mode on the IDSM-2 (a new Native IOS versions with this support is currently in development).
So to get Inline (IPS) functionality you need to be running a Native IOS version 12.2(18)SXE or later, and on the IDSM-2 run IPS versions 5.1 (or even the older 5.0).
(NOTE: Cat OS 8.5(1) does support all 3 modes of the IDSM-2. So if you are using Cat OS instead of Native IOS, then run version 8.5(1) to have access to all of the features of IPS 5.1(1) on the IDSM-2)
If you are running a Native IOS version prior to 12.2(18)SXE then the IDSM-2 can only be operated in Promiscuous mode even if 5.1(1) is loaded on the IDSM-2.
However, even in promiscuous mode the IPS 5.1(1) software does have a few advantages.
There are several engines, and engine parameters that are only supported in the 5.1 version and not the 4.0 version. So there are several signatures that are either a) not even created for 4.x sensors, or b) the 4.x signature is not as precise as the 5.x signature in the new engines.
(These new engines have proved invaluable in writing signatures to detect some of the new attacks that have come out over the past year.)
There are of course other advantages as well:
For example:
1) Risk Rating to better aid in prioritization of alerts.
2) More flexible fitlering mechanism for alerts that allows for fitlering individual actions
The 2 features above are just 2 of the new features that have been added in 5.0 and 5.1 that apply to both promiscuous and inline modes. -
Hi All,
I need to find an iOS version that supports BGP, Dot1q, and MPLS for either a 1800 series or 1900 series not sure the best place to find this sort of info out.
Sorry if this post is in the wrong section.
Many Thanks
Lee
Sent from Cisco Technical Support iPad AppGo here: http://www.cisco.com/go/fn
Maybe you are looking for
-
Just rebuilt new HP 355 G2 to Win 7 64 bit. The ONLY driver I can not locate or get to work is the PCI Encryption/Decryption Controller. I installed all latest drivers for this model/OS from both HP and AMD sites still no luck. AMD autodetect utilit
-
Can not send my NEF files to Photoshop CS3...Please Help
Hello Can someone please tell me what I am doing wrong!! I shoot with a Nikon D300. I use Photoshop CS3 along with Bridge and InDesign. I have Windows Vista. Now that the facts are out of the way........ I have tried installing an update of Camera R
-
Adding a 2nd montitor to a iMac G5
I have an iMac G5, 1.8 GHz with 2 GB RAM running OSX 10.5. I'd like to run a 2nd monitor and have an Acer AL1916W handy and wonder if I can link it to my iMac? Is it a simply matter of getting a cable from Apple that connects to the back of my iMac t
-
Refresh a single chart in a series of charts
Hi All, I have a screen with 4 charts. But I want to refresh each of the charts after a particular duartion. For example the first chart should be refreshed after 1 minute. The second chart should be replaced after 30sec...... And so on.........
-
Workspace/Developer users and Oracle accounts
We plan to install Apex 4 (for first time) into an existing database with many schemas and users. Some users already have developer privileges in their schemas pre-Apex install. Will their user/schema privileges be 'inherited' into the Apex environme