Mismatch between startup and running cofig after power up

Hi Experts,
I faced a strange issue today and looking for some inputs if somebody have faced this issue and any reaon for the same.
Problem
=======
Switch : 3560
IOS : c3560-i9-mz.122-20.SE1.bin
Today in my network there was a power down and we took the backup before that and also applied wr mem.
After power up we saw one config was lost "static route command" was missing
Then I did show config and also tried sh startup and saw that command was still there.
My question is after power up if something is there in startup config (nvram) is should be loaded to DRAM and come in running config but why "ip route " command did not came.
Looking for some valuable information and thanks in advance.
Regards,
Ankur

Yes, I'm assuming it would happen in either case (static to interface or static to next-hop) because if the interface is down you wouldn't have a path (the effect is the same ... no path to the destination).
Is the link on that connection such that you could use portfast / uplinkfast (without risking a loop)?
To me, since you can do the 'copy start run' and it "takes," that the problem is that the interface is down, not initialized, or not available when the routes are being created from your start config.
It may also be that the other side of the connection is staying down during the switch boot & initialization. same thing, if spanning-tree portfast / uplinkfast can be implemented with little or no risk, give it a shot and see if it resolves the problem.
Good Luck
Scott

Similar Messages

Mismatch between availability and marker

I have run the following command:
/repvfy -detail -fix -pwd password
and am seeing a section called "Mismatch between availabiltiy and marker". What does this mean? I know there is a bug out from Note: 735957 against 10.2.04 and that patch 6951116 is available. I also know this bug is fixed in 10.2.0.5. But I don't know what exactly this section is telling me. Here is the output I am seeing:
6. Mismatches between availability and marker
TARGET_GUID TARGET_NAME TARGET_TYPE MARKER_AVAIL_STATUS MARKER_TIME CURRENT_STATUS START_TIME
9CB8EE19415C3C6B55954BF3346C1106 ssan-Internal Concurrent Manager oracle_apps_icm 6 09-JUN-2009 10:41:50 1 28-MAY-2009 14:25:22
1B21AAEF5AC63DD44FE339B7852EA1EE ssan-Report Server_ssan_devstar2 oracle_apps_reports 6 09-JUN-2009 10:41:50 1 28-MAY-2009 14:25:13
F5EAD749526EC1116A70157771E3D011 ssan-Oracle Workflow Agent Listener oracle_apps_wfalsnr 6 09-JUN-2009 10:41:50 1 28-MAY-2009 14:25:29
CD32714673BC508CDBF85BF191A5A1B7 ssan-Workflow Background Engine oracle_apps_wfbg 6 09-JUN-2009 10:41:50 1 28-MAY-2009 14:25:26
FADA1D6BF4DFD0E8AA1739A6666BA210 SSAN oracle_database 6 09-JUN-2009 10:41:50 1 28-MAY-2009 14:25:40
0BE2ACE2EDC7271744DA1A249E30C9A5 APPS_ssan oracle_listener 6 09-JUN-2009 10:41:50 1 28-MAY-2009 14:25:12
89D241EEEF24821E30AD66741BC3D433 devstar2.rtd-denver.com oracle_listener 6 09-JUN-2009 10:41:50 1 28-MAY-2009 14:25:20
F40BAF501645A5957A498E7A270AEA47 ssan-Apps Listener_ssan_devstar2 oracle_listener 6 09-JUN-2009 10:41:50 1 28-MAY-2009 14:25:28
8 rows selected.

Various provision like Freight, transport etc .
these should go to separate GL accounts. if you give wrong account assignment value will be passed to GRIR. then difference will happen
sunoj

Config mismatch between VSM and VPath - CSCum76142 bug

Hi all,
I got the error message "Config mismatch between VSM and VPath" on my Nexus VSM but I could not see any detail regarding this bug ID due to permission issue. Has anyone else got access to see this bug detail and able to share? I need to know if this bug is critical or just cosmetic. Thanks
regards,
Robin

Hi Robin,
This DDTS was Junked. But here's the workaround that is mentioned:
1. Deleting the vservice config (no vservice) & reconfiguring vservice, will get rid of this mismatch issue.
2. Toggling the port-profile should also work.
I see couple of other DDTS as well related to this and i would suggest to ask this question in "Other Data Center Subjects" forum for detailed and quick answer.
CSCtz36835 :Config mismatch on VSM and Vpath after deleting service vlan
Regards,
Kanwal
Note: Please mark answers if they are helpful.

Mismatch between sound and video

When I watch a movie in iTunes of Apple TV (2gen) and I want to move it few seconds/ minutes and more backwards then it like "losing its mind",
the video jumps forward (a lot forward) and the sound stays the same, so ther is mismatchment between sound and video.
What can i do to solve this problem?
Thank you!

Am I the only one suffering this issue with the video transcoding?

Color mismatch between CS4 and Canon PIXMA PRO6500

Hi there! I am trying to research if anyone else is having a problem with color mismatch between CS4 and their printer. Last night I printed a .tiff image out of CS4 to my Canon PRO6500 printer and the sky came out purple / pink! It was supposed to be a stormy grey color. I have the color management turned off on the printer settings. I have CS4 manages color turned on and the correct ICC profile selected for the paper I am using. When I do a soft proof in CS4 the image looks fine, but when I print I get something completely different, mostly with the sky (purple / pink) color! Just for the heck of it I did a Print Preview under my Page Setup and guess what, the sky actually shows purple / pink! So I have no idea what's going on. I checked all my setting, ink cartridges, tried different paper with the appropriate ICC profile and no dice. Still have a goofy looking sky! I thought PROOFING the image is supposed to show you how the printed image is going to look? apparently it doesn't because it's not. The Print Preview has an accurate representation of the print but I have no idea where the pink / purple sky is coming from. They are supposed to be stormy clouds as I said. I appreciate any help anyone can provide .
Sabciu

I have the color management turned off on the printer settings.
But do you have a measured color profile based on a sample print? Most likely not, so this is not doing anything in your favor. The current profile may present the defaults for a given printer, but not the actual density based on your other printer settings. So by all means, unless you can be sure to obey a full calibration throughout, turn on the printer CM. Also, since it is a Pro model, you may actualyl have to use the dedicated RIP software that was bundled with it to get correct results, not the default windows print engine.
Mylenium

Contrast mismatch between Organizer and Editor

I can edit an image in Editor to where it looks great, to include the contrast, brightness, shadows, etc. When I send it back to the Organizer, it look much too contrasty and dark. When I use the same images in a slideshow originating in Organizer, they still look too contrasty. Is there a way to correct this? I'm using PSE 10 on a Windows 7 -64 bit machine. Thanks for any ideas.

Thanks for your quick response. I just checked out the settings in both the Editor and Organizer and they're both set on "let me decide". I'm not sure what to do on that one. I could go with optimizing the computer screen with sRGB, or the Adobe RGB for the printer, or no management, or decide on the fly. If I go with the computer, I guess I'd have to change it when I print a photo out, and vice versa. Have any suggestions for me? Thanks again.
New update. I have a Dell color laser printer, and I just checked the manual. It offers both sRGB and AdobeRGB. My priority is really to have a good printout. If I check sRGB I should be safe for either print or computer, but I'm wondering if I'd get as good a printout with sRGB as with AdobeRGB. The easiest might be to see what the printer is curently set on, and then set PSE Organizer and Editor to match it. I'll do that, and then see if that helps the mismatch between Organizer and Editor.

Data mismatch between 10g and 11g.

Hi
We recently upgraded OBIEE to 11.1.1.6.0 from 10.1.3.4.0. While testing we found data mismatch between 10g and 11g in-case of few reports which are including a front end calculated column with division included in it, say for example ("- Paycheck"."Earnings" / COUNT(DISTINCT "- Pay"."Check Date")) / 25.
The data is matching for the below scenarios.
1) When the column is removed from both 10g and 11g.
2) When the aggregation rule is set to either "Sum or Count" in both 10g and 11g.
It would be very helpful and greatly appreciated if any workaround/pointers to solve this issue is provided.
Thanks

jfedynic wrote:
The 10g and 11.1.0.7 Databases are currently set to AL32UTF8.
In each database there is a VARCHAR2 field used to store data, but not specifically AL32UTF8 data but encrypted data.
Using the 10g Client to connect to either the 10g database or 11g database it works fine.
Using the 11.1.0.7 Client to go against either the 10g or 11g database and it produces the error: ORA-29275: partial multibyte character
What has changed?
Was it considered a Bug in 10g because it allowed this behavior and now 11g is operating correctly?
29275, 00000, "partial multibyte character"
// *Cause: The requested read operation could not complete because a partial
//          multibyte character was found at the end of the input.
// *Action: Ensure that the complete multibyte character is sent from the
//          remote server and retry the operation. Or read the partial
//          multibyte character as RAW.It appears to me a bug got fixed.

Hi ..my iphon when reach the charge to 20 or less it shut dawn and run it after 2 min..why !

Hi ..my iphon when reach the charge to 20 or less it shut dawn and run it after 2 min..

Hi Mac Attack,
My computer will not disconnect from the internet. It seems to find a clone router and continues even when I shut down and unplug my my own home iy
Your main question was 'chopped' in the title. Please reply in the body of a reply box with the full question and anything you have tried. And no, the long report was not helpful .
If the same website is opening each time you launch a browser (Safari?) hold down the shift key as you launch to prevent previous pages from opening.
Have a look at your settings in Safari > Preferences. Especially General and Privacy.
Reset Safari to remove cookies and other stored data.
System Preferences > General
Have a look at your settings in System Preferences > Security & Privacy.
Call back with more questions.
Regards,
Ian

Data mismatch between TABLE and Std. Extract str. (AFPO & 2LIS_04_P_MATNR)

Hi,
I am getting data mismatch in ECC standard table and ECC standard extract structure. Please help me.
I am using 2LIS_04_P_P_MATNR data source (standard extract structure).
I have following data in ECC Table (AFPO - Order Item).
AUFNR (Order Number) --> 4000460
PGMNG (Total planned quantity) --> 0
PSMNG (ORDER QTY) --> 2000
Extract Structure is showing following data.
AUFNR (Order Number) --> 4000460
PGMNG (Total planned quantity) --> 2000 (It should be zero)
PSMNG (ORDER QTY) --> 2000
I have checked with many other order numbers. The extract structure in RSA3 is showing correct values only if PGMNG is non-zero values. If PGMNG is zero, then it is automatically assigning PSMNG value.
Is this common? I want to display correct values for PGMNG from AFPO Table. Why this mismatch between table data and extract data. I have done all required steps refreshing data (deleting setup tables, filling set up tables etc.).
pls suggest. Poinsts will be assigned to every useful answer.
Thanks in advance.

Hi Avneet,
I have a similar problem where in AFPO shows value 1000 in PSMNG field and 1200 in RSA3 for extractor 2LIS_04_P_MATNR.
I have found that the standard feature of the extractor extracts the data at the time of release of process order. If the process order is changed after the release then the extractor will not picup the chagne.
Ex: AFPO value 1000 ---BI Value 1000
Now released in ECC
AFPO value 1000 ---BI Value 1000
In ECC value changed to 1500 after the release. BI will not pickup the change.
Extractor is pulling the data from MCAFPOV table. You can check the values, there it matches with RSA3 values.
I was just going thru forums for the solution. After i found the solution. I am just updating it.
Hope it helps you.
Thaks
Srikanth

What is the difference between start() and run()

Hi:
what is the difference between start() and the run()???
in my app, i have
Console.debug( "starting thread to listen for clients" );
_server = new Server( this );
_server.start();
_server extends Thread..
why everytime i use server.start(); my app will terminate on it is own, even though in my servr.run() method, i have a while loop
and if i call _server.run() explicitly in my code, that while loop will be in execution
can someone let me know??
thnx

what is the difference between start() and the
run()???start() is a method on Thread that tells it to start.
run() is a method in the object that the thread executes.
why everytime i use _server.start(); my app will
terminate on it is own, Err.... I'm not convinced this is true. It'll throw an IllegalThreadStateException, if you try to restart an existing thread.
If that's what you're saying.
even though in my _servr.run()
method, i have a while loopI don't see the connection. Are you saying that the while loop never terminates, and you don't see why the thread is terminating?
and if i call _server.run() explicitly in my code,
that while loop will be in executionIf you call server.run() explicitly, then run() will be executed in the same thread that you called it in.

SQL: System locks up and runs slow after performing simple DML record insert

SQL Version: 2008 R2
I am having a serious problem. I ran the following code to perform a simple table record insert which ran successfully. However, after running this code I could no longer access the related table. I couldn't run a query against it.
I tried to delete all the records and that wouldn't work either. When attempting to run any DML statements (i.e. Select * From vPCCertificateTypes) against this table SQL gets locked up and never returns anything and no error messages. I have
to manually stop the query. Now the entire SQL system is running slow.
Any help would be greatly appreciated. The code I ran to originally insert the records is below.
Regards,
Bob Sutor
CODE:
Begin TRAN
INSERT INTO vPCCertificateTypes (VendorGroup, CertificateType, Description, Active, Category)
SELECT HQCo, 'MBE', 'Minority-owned Business Enterprise', 'Y', 'Affirmative Action'
FROM HQCO
Where HQCo IS NOT NULL
AND HQCo <> 100
AND HQCo <> 99
IF @@ROWCOUNT <> 44 ROLLBACK ELSE COMMIT
Bob Sutor

The problem was an open uncommitted transaction against the table as you suspected. I ran your code and it cleared the transaction. In the past I would intentionally leave our the Commit statement and then if the transaction ran fine, I would
simply highlight and run 'COMMIT' and it would close the transaction. Apparently that is not the correct approach. I'll use your suggested code from now on.
Thanks for the help.
Bob Sutor

Timing mismatch between picture and sound.

I have been using Premier Element ver. 12 with my films recorded with my Canon EOS camera without any problems. I have now been trying to clip a film recorded with a MAC copmuter. The files have .mov extension. My problem now is, that the sound and the pictures are not sycnroniced anymore. It seems that the Pictures are 3 seconds faster per minute than the sound. So after 20 minutes the Pictures are 1 minute in front of the sound. Playing the original files with the Windows player Works fine and the timing of the sound in Premiere Elements fits with sound using the Windows player.
Any Ideas????
Gert Munch

Hi' ATR
Ref. #8
Loading one of the problem files into Movie Maker Shows a small but constant shift between sound and Video within Movie Maker. Easy to fix. Exporting and import into Premiere Elements shows the same small but constant misallignment. That is good.
The screenshots of the required readings is seen below
Properties from Premiere Elements:
I did not dare to install the MediaInfo properties readout program as I was warned about malware.
Ref. #9
From Movie Maker the Video bitrate is stated to be:
15-12-14: 177232 kbps
12-01-15: 81164 kbps
16-02-15: 177396 kbps
10-03-15: 280596 kbps
From the above screen shots the audio bitrate seems to be 128 kbps
Hope this makes sense to you.
Gert

DataSource / Structures mismatched between Dev and Test Systems. ..!!

Hi,
We are doing a scenario. Where XI will update the data into PSA through ABAP proxy.
Scenario worked perfectly in development system.
We transported the objects from Dev to test. The Strucures are mismatched in SE11 between development and Test systems as below.
Data sources (ZDS_RECIHDR and ZDS_RECTPALL) looks ok. But when I saw the structures in SE11 they are not correct, they got mismatched.
Development:
/BIC/CQZDS_REC00001000 - Header (ZDS_RECIHDR)
/BIC/CQZDS_REC00003000 - Allocation (ZDS_RECTPALL)
Test:
/BIC/CQZDS_REC00001000 - Allocation (ZDS_RECTPALL)
/BIC/CQZDS_REC00003000 - Header (ZDS_RECIHDR)
Kindly let me know where it might have gone wrong?
Thanks
Deepthi

We done it already. Still it is failing.
While transporting, it is failing and showing the error as
Program ZPI_CL_IA_PAYMENT_ALLOCATION1=CP, Include ZPI_CL_IA_PAYMENT_ALLOCATION1=CM001: Syntax error in line 000016
The data object 'L_S_DATA' has no component called'/BIC/ZSALENUM', but there is a component called
Program ZPI_CL_IA_PAYMENT_HEADER======CP, Include ZPI_CL_IA_PAYMENT_HEADER======CM001: Syntax error in line 000016
The data object 'L_S_DATA' has no component called'/BIC/ZTRANDATE', but there are the following com
The Structure is mismatched in SE11 between header and allocation structures. That is the reason it is failing.
Any more ideas pls?

PPDS production order dates mismatch between APO and R3

Hi Friends,
We are facing one problem regarding production order date mish match between R3 and APO systems specific to a product.
The product is planned in PPDS and the order automatically transfer to R3 through online CIF.
PPM has got two operations 0010 and 0020 and activity relationships are like this:
P(0010) - P(0020) Start - Start relation ship
S(0010) - P(0010) End - Start relationship.
In PPDS dates are shown as :
on operation 0010 the start/end dates are shown as 08.15.09 to 08.22.09
on operation 0020 the start/end dates are shown as 08.15.09 to 08.22.09
Overall order start date is 08.15.09
Overall order finish date is 08.22.09
and in R3 dates are shown as:
on operation 0010 the start/end date are shown as 08.15.09 to 08.22.09
on operation 0020 the start/end dates are shown as 08.22.09 to 08.29.09
Overall order start date is 08.15.09
Overall order finish date is 08.29.09
The order is off one week (APO vs R3) with start and finish dates.
if we change DS Board settings to ignore internal relationships manually then the dates are matching exactly in APO and R3.
We want the production order dates to be matched without manual intervention.
Could some one please provide some hints on what is happening here and how to correct it.
Thanks.
Krish

Hi Friends,
Thanks a lot for your valuable replies in this regard.
Actually this problem is in production environment and it took some time to test the problem with the master data modifications
you suggested.
As DB and Siddhrath mentioned, the problem was with routing definition. There is no parallel sequence maintained in the routing but there is start-start relation maintained in APO PPM.
We corrected the routing definition and checked the order dates. Now the dates are matching in R3 and APO.
I am awarding DB and Siddharth each five points in this regard.
Once again thank you all for your time and valuable replies.
-Regards
Krish.

Data mismatch between dashboard and bw report

Hi expert,
Data is mismatchin between dashboard and BW report of .I am using SAP BW connection ,
Dashboard screen shot
BW Query output
What is the issue can you please suggest...

Hi Ganapathy,
Please check the Prompt filter and Variables which you are passing to get the output in Dashboard and BW.
It seems that some filters are missing in dashboard.
Thanks
Arvind Shukla

Mismatch between startup and running cofig after power up

Similar Messages

Maybe you are looking for