MSI 845E Max 2 RAID Help
I have a Seagate baraccuda 40GB HDD. When i connect it to RAID, it dectect Functional but it give a warning like
your HDD ATA66 or above will downgrade to ATA33 to prevent this goto BIOS setup #2 in DMA setup to configure it.
in this situation, I don't know how to go ?( Please help me.
Ok,
No.1 Are using an ata66 ide cable? (80 conductor)
No.2 Go into the promise bios using ctrl+f and try to set the mode of the drive to ata66.(udma 4 I think??)
No.3 ata66 may be disabled on the drive, you need to go to the Seagate site and download their utility to change it back ata66 mode.
Hope this helps...
Similar Messages
-
Hello
The mb MSI 845E max give's me cpu temp 50 degrees celcius idle and 65 degrees stressed.
This is not normal are there users who have the same probleem with this mb MSI 845E MaxQuote
Originally posted by t1955feb
Hello
The mb MSI 845E max give's me cpu temp 50 degrees celcius idle and 65 degrees stressed.
This is not normal are there users who have the same probleem with this mb MSI 845E Max
Hi!
So I already have 845E Max (MSI-6566E), so I have this prob. In idle 46~48C, and on high use 55~57C.
I think it is bad, because in this temperature can't overclock the system, or not stable :(
And the Intel Cooler, (in the BOX version of CPU) so weak.
So 2 solution we have:
1.) Big copper cooler, with least 6 or 8cm fan.
- can be noisy :-(
2.) Watercooling system
- the best choice (I'm already on making )
- quit
- safe
Just Do It!
Nice Day 2 U Meeen!
TLOYL -
I cant seem to overclock my p4 1.8a over 125FSB. At this setting i can overclock my memory to 333mhz or 250mhz, no problem there. If i try to overclock any further i get 8 beeps which, when i check out the beep codes, indicates a memory error on the video card which is a Creative G4 Ti4400, not overclocked. All i can presume is there is no way of adjusting the AGP bus which is overclocking the G4 too much!!! Anyone know how to overcome this problem???? ?(
MSI 845e max
P4 1.8 @ 2.25
Creative G4 Ti4400
Maxtor 20GB
Ricoh CDRW
Toshiba DVD
Win Xp ProI don't have an answer for you just letting you know that I got my P4 2.0a to 145FSB (2.9GHz) can't go higher. Therefore it's not the mobo it's one of your components.
P.S Add brand/speed of your memory to your signature. -
MSI 845E MAX Processor Question
Greetings All,
This may be a silly question, but what is the fastest processor I can plug into the 845E Mainboard? I currently have a P4 2.0 but want to know how much higher I can go.
Thanks for any help :D
Stephen?(
845E Max 6566E..???
http://www.msi.com.tw/program/support/cpu_support/cpu/spt_cpu_detail.php?UID=313
if you need can check msi website CPU Support Status for more info...
all the useful info all are inside... -
MSI Mpower Max 4770k Help tweek it
Hi there,
this is my first seriouse MSI board in last 3years and i have encountered few problems with overclock
My Pc Specs are:
Intel 4770k
Corsair H70 with 2xNoctua 14FLX p/p
MSI Mpower Max
Kinston Hyper X DDR3 1600mhz 9-9-9-27 2x4GB
Corsair AX860
Intel SSD 510 250GB
Seagate Barracuda 3TB
Samsung F4 2TB
Corsair 650D
all day passed and i am a bit tired of seeing bios and bsods
i think i got the lazy chip help me understand it better and learn things on the way.
this is most stable i got.
Bios E7815IMS.133
CPU ratio: x44
Ratio: Fixed
Ring: x39
Vcore 1.25v Offset 0.015V
Svid comm. Enabled
from digitall i changed only CPU Vdrop to 100%
Ram set on xmp and manualy entered timings and voltage and speed 1600
With this i pass AIDA 64 stress test for 30min no problem
cinebench pass
when i open Prime95 Blend test 15min pass and bsod..
Temps were 80-85c with room 25c
Everything else in bios is set to default (auto)
Any tips how to tweek it more?
i tried x45 with settings as above i boot into windows pass cinebench but crash on aida64.
i also tryed just x46 with voltage bump up to 1.28v with offset 0.015
I will be deliding as soon as my h220 arrives and CLU.
Also is there some special USB so i can take the screenshots?
i tried all the ports different flashes also formated to FAT32 and NTFS same its saying no usb dongle..
When i put my WD 2TB HDD it recognize it but when i want to save the Screenshot it gives this message
"allocate file system resource fail"
I would post Screanshots but as i mentioned above its annoying problem..
Thanks in advance guys.
Edit:
just to see if i have lazy chip i tryed 1.3v with settings above and x47-48 wont even post.... :(
found flash that is workingok i tryed this also
Internal VR efficiency management - disabled in screanshots its enabled
with this i am able to make 30mind aida with no crash temps a bit high but can be managed, i boot into windows with this vcore and x45 but unstable during aida 10min bsod
i boosted the voltage to 1.275 with offset 0.015v and got me 20min aida then bsod. any way i can tweek it more? -
Degauss prob. w/MSI 648 Max pls help
PC spec. below.....message
Everytime I restart my monitor from Xp or when leaving the bios, my monitor does a degauss. And it gets very irritating X( when you fx. reinstall your PC from start.
The "light" on the monitor also goes from green-orange-green as if it had been shut down.
Have tried conn. the monitor to my other system, and here there are only degauss when i power my pc up.
Have also tried another MSI TD4200 as I have simular in my other PC. no effect at all...
A friend of mine got same PSU and Monitor and his system also degauss only when he power up the PC.
Have anybody ?? noticed a simular problem before, and if what's the "cure".....
To me it "smells" like a bios problems,,,,,,,,,but I be mighty happy to ANY other suggestions.
PC SPEC AS Follows
P4 2,4 533 w/box cooler
MSI 648 MAX
PSU VIP 450w w/an average power on 250w
2x256 Pc2700 Apacer
MSI GF4 TD4200 64mb
ASUS CD
Liteon CDR/W
WD 80gb JB 8mb cache
Monitor AOC 9KLR "new" versionNever the less it does........have tried the VGA card in another PC, and here there are no degaussing.....have also tried another VGA card,,,,,,,,,same deal mate! ?(
Problem is prob. related to the mobo power management......or the comb. of hardware........
I have tried changing every components exept CPU/Memory/Mobo with no changes..........
So to me i'm sorry to say it's looks like a faulty mobo or some mismatch in the bios settings.......... ;(
73/CT -
Need MAJOR HELP recovering an 845E-Max board (no post)
Hey guys and gals, I need some SERIOUS SERIOUS help here recovering my old board. I have an MSI 845E-MAX board, and decided to do some overclocking to it. While doing it, I raised the FSB too much, and now the system wont post. So I know what your all thinking, ok, take out your CMOS battery, or clear the JBAT1 jumpers. While ive done that, repeatedly, to no avail. Ive cleared the jumpers over and over, nothing. Taken the battery out for a 24hr period, nothing. Took the battery out for nearly a MONTH!, and nothing. Next your probally thinking, while maybe its bad RAM, Vid Card, CPU, etc. While it isnt lol Ive replaced/tested all the current hardware in other systems and they all work fine. Ive got a defenet mobo problem, and its really pissing me off lol on other boards by other manufacturers, if I put my FSB to high and it didnt post, restarting would put it into default specs, so I could adjust my fsb as needed. With this 845E though, its no such luck, and reseting the CMOS dosent do anything to fix it. Ive also read some posts about other boards who dont even have a JBAT1 jumper, and used an "insert" key method, where they power down, hold down the insert key, and boot up. Decided to try this, and it did nothing. I didnt think it was made for my board in the first place, but decided to give it a shot. IVe also tried reflashing/recovering the bios, by downloading the newest bios (its an AMI i believe) renaming it, putting it to a floppy, and booting the system holding CTRL+HOME to force the update. but it does nothing, and dosent even seem to read the floppy as the little green light dosent come on when i power up. The DVD/CD drive does though, and wehn i place WIN XP SP2 in the drive, it reads it and green light stays solid, so its just the floppy drive im having probs with I guess. Also, i get no beeps at startup, but can hear the hard drive boot and spin. I list my hardware specs below to help
So PLEASE, some MSI guru, help me before I go crazy here! :P thanx a million to any one who can lend a hand.
MSI 845E-MAX
2 x 256 Azen RAM PC2100
Benq DVD Burner
Intel Pentium 1.5ghz P4
Nvidia Geforce 64mb
*this is a spare system im building, but the board WAS my primary board till I upgraded, so im use to its settings, just no OC'ing it apparently lol*I do indeed...and yah i get no beeps at all....
but everything powers up fine...hdd spins...cd rom turns on, if i put in a Nic card, the green light comes when a cat5 cable is in it. So it looks like everything is receing power fine, but i just get no beeps at all to signify start up -
Help! Problems with 845E MAX HSF seating
have a MSI 845E MAX and a P4 2.8 GHz cpu. I bought a coolmaster L71 for 478 socket type but when I put it on the cpu, the four little plastic white pins that hold the HSF mounting tray in place prevents the HSF from actually connecting with the CPU unless I use a load on paste (which is wrong)
If I take out the pins the HSF sits on the CPU fine but surley this cannot be correct? Has anyone else had this problem or have any ideas why?
I have also tried a mates P4 S478 HSF and it does the same, the four pins seem to stop it touching the cpu correctly.
PartyWhat's up? I got your Email - I don't know about cutting those pins off. Man, that really sucks those heatsinks aren't fitting correctly. What would be wrong with getting a stock Intel fan/heatsink? They are really cheap. I saw one for $7 shipped. Or get the f/h I have. It's a Coolermaster D14-7H53D. However, if you want to try and cut those pins go ahead because you can always buy a new bracket if it doesn't work. Let me know what happens. Good luck.
Man, you can't say (s)ucks in this forum. -
845E Max(6566E) Temp Issue
Any1 who uses this mobo has some temperature issues? Pls post ur idle/full load temperature here n see whether we have some temperature abnormalities...
I'm running a P4 2A Ghz with Volcano 7+ & AS3 applied evenly.
My temperatures are:
idle: 56^C / 36^C (CPU/Chassis)
full load: 67^C / 40^C (CPU/Chassis)
both with an room temperature of 26^C.
What u have with ur temperature? Do share.Idle: 45C-48C/28C-33C (Depending how hot it is outside)
Load: 49C-56C/34C-36C (Depending how hot it is outside)
Outside Temp is : 32C-38C
My Thermaltake LCD probe displays case temp at 1C-2C higher than the MSI mobo sensor. This leads me to believe that there isn't anything wrong with my mobo's temp detection. )
I have hooked up my Tornado a.k.a The Blowdryer to a Fan switch with H/L/M settings. When I am not doing anything CPU intensive I put the Tornado to Medium fan speed and there is a slight increase in temperature displayed in Motherboard Monitor.
System Specs:
CPU: Pentium IV 2.0a @ 2.9 (v1.65)
Mobo: MSI 845E Max-L (Intel LAN)
H/S: Alpha 8942 & Vantec Tornado 84CFM
Memory: Corsair PC3000 512MB CAS2 DDR
Video: ASUS GF3 Ti200 Deluxe @ 240/500
SCSI Card: Adaptec AHA-2940UW
CD-RW: Plextor 12x10x40 SCSI
CD-ROM: Plextor UltraPlex 40Max SCSI
HD: IBM 60GXP 60.1GB & Maxtor 60GB
HD Rack: Tt Hardcano 5 (Golden)
Sound: Sound Blaster Audigy MP3
NIC: 3COM Etherlink XL 10/100
Monitor: Samsung SyncMaster 900NF
Case: Lian-Li 68 (4 Stock FANs)
PSU: Enermax 431w (Auto Speed Control)
Mouse: MS Intellieye v3.0
Keyboard: MS Internet Keyboard
Sandra Benchmarks can be found here:
http://wolfpack88_rig.tripod.com/wolfpacksrig/ -
Is there a compability problem between Radeon 9200 Atlantis,P4 2.66 Gig prosessor and MSI 845PE Max-L ??
Memory module is DDR 400 512 Ram,HD is Maxtor 120 Gig ATA 100
Every single component works fine with my other Motherboard ( MSI 845E Max )
but when I try to start these in 845PE Max-L only thing that happens is prosessor cooler spins 2 seconds...then totally silence....I got a motherboard replaced once
already....
I cleared CMOS
tried another graphic card ( Geforce3 Ti 500 )
Nothing happens even with default settings...
Highly unlikely that two broken motherboards has been given to me !?!?!?!
Please someone tell me what to do..
E-Mail,MSN or here at the Boards...
- THX -"Lower you DRAM Freq to 333MHz and increase you DDR Voltage to 2.7v, thereafter incrasing your AGP Voltge to 1.6v."
Why ? and how ?
cannot go to BIOS..
and I just asked if there is a compability problem...
Danny : no other cooler movement :(
just prosessorcooler spins few times,
there are no shorts between board and case through the standoffs.
I took motherboard out of case ( in case of that )
Whole F****n thing is starting to me off...
Never had this much problems with MSI-boards :(
So,once again ; every component works in 845E max ,same case,same powersupply etc.
Only sure thing seems to be : 2 broken motherboards ! ( god damn ) -
MSI GNB MAX and RICOH R5C476II PCI to Cardbus bridge not working! Help
Why my PCMCIA & CARDBUS Card Reader based on RICOH R5C476II Chipset not
working on MSI GNB MAX BOARD (with newer bios 2.3)???
My Card reader is fine and working properly on many ithers motherboards like: ABIT BD7-II based
on Intel 845E Chipset, or ASUS TUSIM, ASUS TUSL, and ASUS PIIIB-F
Why ??
Please help me.Yes, sure. I'm trying to use all of five PCI slots, and after slot chnge I,m setting Reset Configuration data in BIOS.
result is the same in all Card positions. Card is detected, but not working corectly.
I'm trying to resolve any hardware conflicts by disabling all od internal mothebrord components like IEE1394 Audio, Serial Ata and others - no cahnges, no solutions .... -
MSI Why No HT Support On 845e Max Rev1
Please can someone from MSI tell me if there is anyway to update my 845E Max 6566 MB to utilise Hyper Threading. I have the latest Bios Revision 5.9.
In the specs on this website it says that the 845E Max DOES support HT. Yet mine does not have a Bios menu for it.
Is there any way to enable HT short of buying a new MB (which I do not really want to do as I though my current one should support HT).
TIAhttp://www.msi.com.tw/program/search/ser/SerConProRes.php?pro=1&chp=6
Link to MSI site with 845E chipset. Please confirm which one you have.
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=426
This link is to supported CPU's (Sorry 800FSB not supported)
HyperThreading is ONLY supported under the XP range of Windows......
Has for HARDWARE mods..... be careful!!!!
There is some input from me.........also check the Overclockers section of MSI Forum.....resources there!!!
Del -
Sound Problems with MSI 648 Max ( MS-6585 ) Board - Help !!!
Hi,
i have the MSI Mainboard: MSI 648 Max ( MS-6585 ) and when I put on the microphone i have a bad sound on my soundboxes like scratching or beeping.
I have installed a new BIOS update and new Sounddrivers.
I have Win2000 with SP3.
Anybody can help me???
THX ;(Error404,
I since you have a 648 Max and you posted in the Multimedia Forum, I moved the thread to PIV Motherboard Forum for you.
Good Luck,
Richard -
MSI GNX MAX-FISR P4, RAID Controller
I just ordered and received a MSI GNX MAX-FISR P4 motherboard, and I have a question. My impression is this has a RAID controller, yet P. 2-18 of the manual suggests that I can only connect ONE hard drive to IDE3, the raid controller. THis doesn't make sense to me--by definition a RAID controller must support 2 or more hard drives. Is IDE3 a standard IDE connection and RAID is only via serial ATA?
wonkanoby is right. he and i had this conversation a few days ago. in addition, i called msi last night and confirmed it. if you have 2 IDE drives that you want to RAID on this board, then you can hook one of the drives into IDE3, but you must use an SATA-to-IDE converter for the other drive (and hook it into one of the SATA ports).
i wish they would have clarified that a little more in the product description page on MSI's website. but it's a super board! very easy to set up. -
MSI 648 max problems, please help
Just put a new machine together and I am having some problems, hopefully someone can help.
My machine seems to run pretty stable in OS, but dies when any game is played. It will crash anywhere from 2 minutes - 45 minutes in the game. Ive tried several games: C&C generals, unreal2, etc with the same results.
Bios are updated and nothing is overclocked. Win XP is fully updated.
Specs:
MSI 648 max, 533fsb
p4 2.4 northwood
Seagate 80gig hd 7200rpm
MSI g4 ti4200
2 - 512mb pc2700 ddr333 dims (double sided)
Antec 350w ps
sb live
48x liteon cdrw
16x liteon dvd
We are using a Kingwin KT-436S-WM case
http://www.kingwin.com/product.asp?cid=15&pid=75
It has a total of 5 fans with intake/exhaust
HSF currently being used is the retail box HSF
With the case sides on, here are temps at idle after 10 minutes in OS:
Proc: 136
System: 91
Vid card: 118
With the case sides off, here are temps after running 10+ minutes in OS:
Proc: 125
System: 86
Vid card: 114
Here is the error that pops up (after crashing) when playing Command and Conquer: Generals:
Technical Difficulties
Sorry a serious error occured
Thanks in advanceWell my roomate cancelled the memory test after 12 hours, so I dont know those results.
I do know that after removing 1 of the DIMMS, the machine seemed to be stable playing games.
I sure wish MSI would have stated it only accepted 1 double sided DIMM.. especially when the reccomend Kingston ram, which is double sided......
Me and my roomate BOTH bought this motherboard, while my roomate only bought 2 DIMMS of 512, I bought 3!!!!!!!!!!!!!!!!!!!
So now it looks like we need to return these motherboards and get new ones... I HAVENT EVEN GOT MINE OUT THE BOX!!!!!!!!
Any reccomendations on an MSI motherboard (or any) that support double sided DIMMS? I am looking for 3 slots...
thanks...
Any other advise on how to get this motherboard to work with all this ram would help too, so we dont have to RMA through newegg....
Anyone from MSI read this board?????
X( :O ?(
Maybe you are looking for
-
Itunes bounces, but does not open
Since installing 8.1, when i click to open itunes it bounces, has the appearance of opening, and then just stops, and does nothing. why? how can i fix it?
-
Print Multiple Pdf's with Acrobat X pro
I would like to print multiple pdf's from folder but when i highlight like 7 pdf's then do right click there is no option to print. We had this option in acrobat 9 pro. Also one of the user computer only ahve acrobat reader and that user able to pri
-
Crystal Reports for Visual Studio and (Wcf) Web Services
I´m evaluating Crystal reports for Visual Studio 2010. I want to read data from a (Wcf) Webservice into the predefined Reports and deliver them to the Users in an ASP.NET Application. As far as I see reading Webservices via the XML/Webservice datasou
-
Problem Blackberry ID with BlackBerry Classic
Hi everyone, I have a New BlackBerry Classic and i cant confirm My BlackBerry ID on my Phone. The login via web is not a Problem. So my Device does not send me a email confirmation. If i Type my correct password in to the Phone, it does not react. An
-
How do you add a signature to your images in Aperture?
How do you add a signature (ie: jpg my name is) to your images in Aperture? I'd like to put together a look for my images and apply it to the photos. Currently it looks like I have to touch up in Aperture and go to PS3 to add the signature. Is there