Nintendo Wii cannot recognize Airport extreme base station

As titled. Installed the AEBS today, all seems well until I tried to setup the Wii for web surfing. But it couldn't found the access point that's related to the AEBS, but it find other access points that's not related to me. I also tried "manual" setup, but it still couldn't locate the SSID. Are there any firmwire to download and fix this problem?
Please email me if you have any idea: [email protected]
much appreicated.

In finder, go to - Mac HD, Library, Preferences - drag the folder 'SystemConfiguration' into the trash
Restart.
Evidently, there were some corrupt files in there which, in my case, made my AP utility sporadically lose both my airport devices. Trashing that folder and the files within, and restarting automatically creates a new fresh system configurations folder. The AP Utility immediately found my hardware with this fix, but only time will tell if this was root cause and be a long-term fix.
Best of luck.

Similar Messages

Mac book cannot find airport extreme base station

Hi
Basicly, the airport utility cannot "discover" the base station. Ever so occasionally it finds it but when i click on continue it says "there was an error connecting to the network"
I have tried restarting the airport extreme several times.
Please help!!
Tom

Have you tried doing a hard reset of the AirPort Extreme base station (AEBS)?
Have you tried temporarily connecting to the AEBS via Ethernet to configure the AEBS?

Cannot see Airport Extreme Base Station--Watch for 2.4Ghz traffic!

(Issue is addressed in the body of this post)
Great when working on 802.11n at 5Ghz, BUT...
If you have to be compatible with 802b/g you are forced to transmit at 2.4Ghz. Traffic at this frequency can be so bad that it made my station invisible (even with "Interface Robustness" activated). The "automatic channel selector" is supposed to choose a clutter free channel for clear communications, but it does not work well. I had to reprogram the station (through ethernet) to manually change the channel to a more stable one. In my case, channel 8 did the job.
After this, the Airport base worked perfectly!
I live in a condo area where I get 8 strong wireless networks, all at the same time. Add microwave ovens, TV's and cordless phones and you get a jammed 2.4Ghz highway. Make sure to select a channel that provides seagway to the "carpooling lane".

Bob - Thanks so much for your quick reply. I followed your suggestions and, to go into perhaps unnecessary detail, I'll write what I did. I completely disconnected the Airport Extreme Base Station (AEBS) from my computer. I disabled Windows Firewall, uninstalled my anti-virus program, and uninstalled Airport Utility and Bonjour, recycled by cable modem (took out the battery and unplugged it for about 20 seconds), then restarted my computer. After the computer booted up, I verified that windows firewall was disabled, reinstalled Airport Utility and Bonjour, then reconnected the cable connecting the AEBS to the computer (to one of the three ethernet ports, and I tried each of them in case one was faulty) but not to the cable modem as my firewall was disabled and had no anti-virus software. I also reconnected the AEBS power chord. I opened the newly reinstalled Airport Utility software and it did not find the base station. Only when I used "configure other" was I able to access the AEBS. I recycled the modem again, but that did not help. I turned on the firewall, installed anti-virus software, connected the AEBS to the modem, the light turned green, and I was able to access the internet on the primary computer and the wireless network gave me internet access on my laptops. But I was still not able to have my main computer, the one directly connected to the AEBS able to see it, and configure it, without utilizing "configure other."
Also, any idea why one of my laptops can only access the "guest" network? When it attempts to connect to the primary network it will stay on "acquiring network address" for what seems a few minutes, then switch to the "guest" network and connect immediately.
Any help would be greatly appreciated.

Powerbook cannot detect Airport Extreme base station

I bought a new Airport extreme and cannot connect to it wirelessly. I called and tried to do everything to fix the problem but ended up having to have a replacement Airport sent to me. The new one arrives and same problem. I can see other wireless networks but cannot see the one from mine. When restarting the base station, I see my network for a second but it goes away and I can't connect to it. I'm thinking it might be my computer but I can see other networks... any suggestions on how to rectify the problem?

Ok, thanks. I can only see, at this time, five choices:
Try each step one-at-a-time, until successful. After each step, try accessing the AEBSn via Ethernet.
o Shut down the AirPort Utility, and then, restart it.
o Unplug the AEBSn, wait at least 5 minutes, and then plug it back in.
o Reinstall the AirPort Utility on your PC to rule out any issues with the initial installation.
o Install the AirPort Utility on another device (PC or Mac) to see if it can access the base station.
o Perform a "hard" reset of the AEBS.

Windows 7 Does Not Recognize Airport Extreme Base Station

I have a Macbook Pro, a Windows XP PC, an Airport Extreme and an HP Printer hooked up via USB to the Airport. My XP system and My Macbook work fine. I have Windows 7 installed via bootcamp on the MacBok. It connects to the wireless network perfectly on the Windows 7 side but when I run the Airport Utility it is "unable to find any apple wireless devices." I want to set up the Windows 7 side to print and need to discover this network printer but since it won't even recognize the Airport device, I don't know how to proceed. Anyone know how to solve this problem? I have uninstalled and reinstalled software to no avail.
Thanks,
Thad

I have the exact same issue with a new airport extreme. One additional bit of info for me is that the windows computer does see the wireless network and is able to get online. It just doesn't find the airport in the airport utility app. Also, according to the guidebook I am supposed to install "Bonjour" on Windows computers. Can't find any reference to Bonjour on the installation disc that came with the Airport Extreme.

Cannot configure Airport Extreme Base Station

I have a base station in my classroom. It was plugged in 4 years ago stock, and it has run fine as is all this time. I started to get annoyed about temporary signal drops that occurred from time to time. I was told that updating the firmware would limit these (but not eliminate them)......and now my problem. I tried both airport utilities to no avail. Both give me error messages ("an error occurred reading the configuration") when every I try to set it up. I did a hard reset, but that did not alleviate the problem. I know the default password is "public".....not sure what to do from here. Any suggestions?
The base station is running firmware 5.0.3....which is quite old. My laptop is a G3 iBook running 10.48.
Interestingly the router still works pretty well.....I am using it right now to get on my school network...but I would like to put a password on it and update the firmware.
Thanx
Shawn

Shawn, I'm having the same problem, exactly. I had to disconnect my networked HD for a while (renovations) and when I plugged it back in, I couldn't see the ethernet port. When I went to Airport Admin. Utility, I couldn't configure the airport base station.
I went through the "cold start" procedures and used "public" but to no avail. I still have access to the 'net but am concerned that my security has defaulted to -0-.
I am going to try to direct connect tonight when I get home, but if you have luck, would you please post your answer? I will do the same tonight if I figure it out.
I've been pulling my hair out for a week trying to figure this out!!
Good luck.
Thanks,
Dave

Airport utility no longer recognizes my Airport Extreme Base Station, which had been set up to extend a wifi network

Hi. In November I set up my airport extreme base station (5th generation I believe) to wirelessly extend the wifi network we use at home to see if it would increase download speeds. Before doing that, I did a factory reset of my airport extreme, and the owner of the airport extreme to which the ethernet cable is attached made changes to his network to allow it to be extended. I folllowed all the directions from the apple support pages, and finally got it to work. I could even access a portable hard drive which I attached to the airport extreme base station being used as the extension. Then a week or so ago I noticed that my laptop would no longer connect to my base station. I did not have time to look into it until this week. Airport utility, either on my Mac or iphone no longer recognizes my base station. My mac is running OS X 10.10.1 and my iPhone is running iOS 8.1.2 I have tried both hard, soft and factory resets of my base station to no avail. The only thing that has changed after doing that, is that when I do a soft reset of my base station, a neighbors airport express appears when it never did before. I can't actually connect to it, but it does try. Then after approximately 5 minutes, it disappears from my list.
Today I went and pulled out my OLD AIRPORT EXTREME base station... you know, the one that looks like a space ship and is running wifi 802.1 b/c? airport utility DOES locate and display that, but airport utility returns a message stating that it cannot be set up by this software. I am attaching an image of that.
Thank you,
John
Does this have anything to do with the fact that 'Back to My Mac' is probably enabled?

I think the initial problem is that your iPhone was connected to an open network that wasn't yours.
Go to Settings > WiFi and "Forget" the network created by that AirPort Extreme, it's older than dirt. Forget your neighbor's network also.
Perform the equivalent actions with your Mac: System Preferences > Network > Wi-Fi > Advanced... Delete every network that appears, including your own.
Then, connect to your own network on all your devices, after which you ought to be able to use any of them and configure your Extreme without any difficulty. You may need to start over with a "hard reset" on both the main AirPort Extreme and the one extending its network.
Does this have anything to do with the fact that 'Back to My Mac' is probably enabled?
Not exactly, but using iCloud Keychain will populate all your devices with the names of preferred networks that any of them connect to, no matter where they are. I don't know why Apple considers that a beneficial feature.

HT1218 After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer. We still have wifi but cannot access the base station software.

After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer. We still have wifi but cannot access the base station software.

Thanks for the reply. I appreciate the response. I tried that approach this evening and it didn't work for me. (Technically it worked for me, when I was hardwired into my base station, but would not work for me wirelessly, which is my main issue.)
Again, using the approach you recommended works only if I have my ethernet cable attached to the LAN port so my computer is communicating directly to the base station through the hard wire. I am able to scan for my base station and make setting adjustments normally this way too.
As soon as I disconnect from the LAN port and try to go wireless is where I run into problems. The Base Station's wireless network I created is available to choose in the top right corner of the monitor with all of the other available wireless devices/networks -- but the network I created does not have access to the internet. I am also unable to configure my Base Station wirelessly. When my Airport Utility tries to scan for the Base Station and Network, it cannot find any Apple Wireless Device. It's like the Wireless Network in my base station is not sending out a signal.
Is there a way to resolve this issue?

Airport extreme base station no longer recognizes password

Away from house for a week. Came back and none of our iPhones, iPads can connect to wifi network. Airport Extreme base station will no recognize my network password to check settings. Airport Epress will not join network either.

Hi danny_A1A!
I have a couple of articles here that should be able to help you troubleshoot this issue. The first is a quick assist article pertaining to Wi-Fi issues and can be found here:
Wi-Fi Quick Assist
http://support.apple.com/kb/ht1145
We also have another article on troubleshooting Wi-Fi connectivity, and it can be found here:
Wi-Fi: How to troubleshoot Wi-Fi connectivity
http://support.apple.com/kb/HT4628
Take care, and thanks for visiting the Apple Support Communities.
-Braden

Airport Extreme Base station cannot connect to Westell C90-36R516-01 DSL modem

Hi,
I just purchased a new Airport Extreme Base station for my 15" Macbook Pro. I set everything up this morning per the docs (all cables are connected properly) but the Airport Extreme is flashing an amber LED, which means it cannot establish communication to the network/Internet.
I'm using an old Westell C90-36R516-01 DSL modem that has been working fine up until now. I've tried switching out the Ethernet cables and different powering on/off combos but nothing appears to work. When I connect the Ethernet cable directly into my laptop, I have to power down the DSL modem, power it back on, and then do several refreshes before I finally get an Internet connection.
I read a previous post about unplugging the modem overnight and then plugging it in the next morning to wipe out the MAC address setting. I will be trying that tonight, but I was wondering if there was anything else I could try in the meantime? Or, is it simply a matter of having to get a newer modem from Verizon because this one is 7-8 years old?
Thanks for any help you can provide.
Solved!
Go to Solution.

Hi Max,
Let's start from the beginning,
The ethernet from the modem should be wired to the Wan port of the Airport...
On page 28 of the users manual it says if the light flashes amber you should unplug the power of the modem, wait a few seconds and power up the modem.
I presume you installed the Airport utility from the disk that came with the Airport?
For more information about the reason the light flashes
Open AirPort Utility, select your base station, and then choose Manual Setup from the Base Station menu. ClickBase Station Status to display information about the flashing light
Here is a link to the Manual CLICK HERE
I was hoping to find out more about the Airport utility to see what's it's capable of doing...

Cannot Connect Airport Express to Airport Extreme Base Station

I have just purchased a new Airport Extreme Base station and have it configured and running properly.
I would like to use my Airport Express to play Air Tunes and have tried to join my Airport Express's network. I have not managed to get this to work.
I have tried to configure the Airport Express manually and in Assist Me mode but every time it reboots to reconfigure the unit, it continues to flash amber. I have done numerous hard resets and followed the methods discussed in other posts but cannot get the unit to connect.
I am running the latest firmware on both units.
Has anyone solved this problem? If so, please help!

Shallers...you are not alone.
I spend several hours this past weekend trying to get a brand new Express to work with a brand new Extreme station using all Apple computers.
Still no luck, after a gazillion permutations.
I really like the Extreme, it works very well, even with non-Apple devices.
The Express is going back....gawd awful thing from the Darkness.

I have just purchased and installed a new Airport extreme base station but now the Airport Utility cannot see my old Airport Express. Are their compatibility issues and do I need to purchase a new Express?

I have just purchased and installed a new Airport extreme base station but now the Airport Utility cannot see my old Airport Express. Are their compatibility issues and do I need to purchase a new Express?

When you can, take a look at the old AirPort Express and locate the model number in the faint print on the side of the device.
If you see A1084 or A1088, this is an older Express version that is no longer supported by the current version of AirPort Utility that you are using with the new AirPort Extreme.
If that is the case, your Express is at least 6 years old...probably older...so it is about time to treat yourself to a new version with much faster speeds and more features.

Cannot access certain web sites through Airport Extreme Base Station

I use the old (round) Airport Extreme Base Station (AEBS). Approximately three weeks ago I could no longer connect to americanexpress.com or to Godaddy or their mail servers. About a week ago the Godaddy sites started working again, but the American Express sites are still not working.
My current setup:
- AEBS connected to Time Warner New York cable modem
- Three Airport Express units - two connected to speakers, and one set up with WDS to provide Ethernet access to computer (PowerMac G5), which is in a separate room from cable modem
- I also have an Airport card in my G5 to connect directly to the wireless network (but that doesn't solve any of my problems)
I have tried resetting all the units, and have also tried running the network with all the Airport Express units turned off, none of which as allowed me to access American Express.
I have the exact same problems with my work-issued Windows 2000 laptop when logged in to the wireless network.
When I plug a computer directly in to the cable modem, I have no problem accessing any of the sites, which leads me to believe that the solution somehow lies with the AEBS - I just can't figure out what it is.
Any help/suggestions are much appreciated.
PowerMac G5, 23" Cinema Display, Airport Extreme Base Station (802.11b/g) Mac OS X (10.4.9)

If you're having trouble with throughput performance or just connecting to some websites, try changing the MTU value, on your Mac, to 1492. (The default value is 1500.) To do so, you can use a utility, like Cocktail or via OS X's Terminal.
MTU will vary with connection type. Cable and non-PPPoE, can use up to 1500, whereas PPPoE connections (WinPoet, RASPPPOE, Enternet, etc.) can only use up to 1492. For secure VPN connections (i.e., IPSec) use a MTU value less than 1500.
The best value for MTU is that value just before the packets get fragmented. To test, use the Ping utility.
OS X: ping -D -s 1472 www.dslreports.com
WinXP: ping -f -l 1472 www.dslreports.com
Reduce 1472 by 10 until you no longer get the “packet needs to be fragmented” error message. Then increase by 1 until you are 1 less from getting the same error message. Add 28 more to this (since your ping packet size, not including IP/ICMP header is 28 bytes). This will be your MaxMTU. (Note: If you can ping thru at 1472, stop, you’re done! Add 28 and your MaxMTU is 1500.)

Airport Extreme Base Station Error 6742 - Configuration Cannot be Read

I have read the existing posts on this topic, but none of the solutions have worked. I have a Windows XP computer and a brand new Airport Extreme Base Station. When I took the base station out of the box, it would not broadcast a signal, even after configuration. I also noticed that the radio frequency was constantly defaulting to "b", which obviously doesn't make sense with an "n" router. So I checked on this site, and it appeared that I needed a firmware and Airport Utlity upgrade. I did both, and now the configuration is inaccessible. Whenever I try to configure the AEBS, the Airport Utility gives me the following error: "An Error Occurred While Trying to Access the Base Station. Make Sure Your Network Connection Is Valid and Try Again." I know my network connection is valid - I have it connected via ethernet cable and obviously the Airport Utility is detecting the base station in the first place.
Any ideas? Thanks!

If you just bought it I would recommend calling Apple, they can help you set it up.
Also you should consider getting a high speed Internet connection. They are very inexpensive these days and would make your Internet experience much more enjoyable. Where you live I would think you have a choice of DSL (available from most telephone companies) or Cable, which would be the quickest but also more money too.
Regards,
Roger

Third party Device connection to Airport Extreme Base Station

I have a new Airport Extreme Base Station (AEBS) that my iMac is wirelessly connected too. I cannot connect my HP wireless printer to the AEBS. The printer recognizes the SSID and WEP password, but does not have a connection & does not print.
I also, cannot connect a Netgear Wireless Bridge for (xBox) to the AEBS. The xBox does not see the SSID at all. What do I do??? I purchased the AEBS because the salesman said it would be the easiest wireless network ever, but I only have problems ! ! ! ! ! ! !
Aaron
iMac G5 Mac OS X (10.3.9)

Very likely a WEP issue.
If you turn off WEP can you now connect and print?
One of the problems with WEP is that the actual standard relies on a 10 character HEX key for 40bit WEP and a 26 character HEX key for 128bit WEP.
In order to make things easier for people, vendors use certain algorithms to convert simple alphanumeric passwords (or passphrases) into HEX keys, thus enabling people to use simple memorable WEP password rather than lengthy HEX keys.
The problem is that different vendors use different algorithms to generate the HEX key and therefore a ASCII password on an AEBS will be hashed differently on a Netgear client and vice versa.
One thing is a 13 character 128 bit WEP password will be hashed by all vendors in the same way (if you use 40bit WEP then a 5 character password is required).
Though sometimes not even that works and the HEX key must be used regardless.
AirPort: Joining an encrypted wireless network
http://docs.info.apple.com/article.html?artnum=106424
Choosing a password for networks that use Wired Equivalent Privacy (WEP)
http://docs.info.apple.com/article.html?artnum=108058
iFelix

Nintendo Wii cannot recognize Airport extreme base station

Similar Messages

Maybe you are looking for