No incoming calls at all Linksys phone adapter SPA2102

I was wondering if anyone can help me. The phone company I was with went under and I am having major difficulties with hooking my linksys phone adapter up to my computer through a router. I can make outgoing calls but everytime that someone calls in it goes strait to the answering machine. Can someone please help me this has been like this for three weeks. I have a D link router that I need my Linksys phone adapter (VOIP) SPA2102 to go through. Please Help !!!!!!!
Message Edited by tinabeebe28 on 10-24-2008 08:51 AM

tinabeebe28 : SPA-2102 also contains router with NAT.
By default, it's only possible to access the SPA-2102's internal WEB from the PC hooked to LAN socket of the SPA-2102 ... WAN web access is disabled by default in the config. Also, the IP may not be 192.168.0.1, this is configureable.
I advice you to use the IVR function (**** 210) from the phone in LINE1 socket to obtain the LAN IP address of the SPA-2102 and then access this address via the SPA's LAN.
More details and/or also the SPA admin guide, and SPA-2100 admin suplement can be found for example here :
http://www.sipura.net/support/
Those are a bit old PDF manuals but it explains basic info about SPA-xxxx adapters, how to use the IVR, how to setup the adapter, what the different options mean etc ... I think it's a usefull reading.

Similar Messages

Trouble w/Linksys WRT54G2 connecting w/Linksys Phone Adapter SPA2102

I am trying to connect my new VOIP phone adapter Linksys SPA2102 with my wireless router Linksys Cisco #WRT54G2 V1. I have DSL and previously had the wireless router connected with a Vonage Phone Adapter and everything worked fine. When trying to connect my new phone adapter Linksys(SPA2102) it does not work. It will work if I connect the new adapter directly with my DSL modem but will not work through my wireless router (WRT54G2 v1). I have turned everything off and restarted all products several times along with the PC and still no luck. The only way I can get my DSL to work with the new adapter is to wire it directly to the DSL modem. Everything worked yesterday prior to trying to use the new phone adapter. I hope this makes sense lol. This is not allowing me to use my laptop through the wireless router. Any help would be greatly appreciated. Thank you.
Jenny

you should try this -- it shows you how to configure wrt54g2 behind the SPA2102 because it is recommended that you put the SPA2102 directly behind modem for better voice quality

Just Updated iPhone 3GS to iOS5, Can't receive any incoming calls at all

Hi, I just updated my phone to iOS5 and now, I'm having these troubles.
- Can't receive any incoming calls at all
- The incoming calls directly goes to voice mail greeting
- No incoming rings & no missed calls alerts
- Also noticed the incoming text with 4 to 5 hours delays
- Sometimes 3G network get lost
The reception (status bar) is good level, can make outgoing calls okay and can send text okay.
I did try reset the network setting and it seems working a few hours then went back to troubles (mentioned above).
I've done 3 or 4 times reset but none have been resolved yet.
Anyone having a same issues?
I have
iPhone 3GS with iOS5
Network with O2 UK
Thanks,

After reset "All network settings" a several times, it seems working but few hours later it 's been gone back to troubles again.
Is this related to iOS5 or O2?
I've contacted the network carrier several times but no-one yet get back to me.
Any ideas, please helps.
Re: iOS5 updated and all incoming calls going straight to voicemail

My iPhone 4 won't take incoming calls. Everytime someone phones me it goes straight to voice mail. What's gone wrong?

For some reason my iPhone 4 won't take incoming calls and everytime someone phones me it goes straight to voicemail what's gone wrong??

Look at the AT&T VVM User Guide for help setting up your visual voice mail.
If you still have problems, contact AT&T Customer Service at 1-800-331-0500 and ask them to check that your account is provisioned for an iPhone 4.

Linksys Phone Adapter PAP2 question

Can i connect two Linksys Phone Adapter PAP2 to one linksys router without creating any networking issues ?

chojna wrote:
Can i connect two Linksys Phone Adapter PAP2 to one linksys router without creating any networking issues ?
Yes you can connect them. Each will get a different local ip address and the router is supposed to keep the port numbers straight. It is easy to change the sip port numbers on one of the PAP2 adapters and to also change the RTP port range on that adapter. Then you don't have to worry that the router can't keep those port numbers separated and you more or less have to make this change if for some reason you need to forward the port numbers in the router.
Message Edited by hw on 12-28-2009 08:49 AM

My iphone battery level more than 50% but if any incoming call or message, my phone going off. How can i repair my battery?

My iphone battery level more than 50% but if any incoming call or message, my phone going off. How can i repair my battery?

i Had a simular issue years ago with my blackberry on ATT. As it turned out, my SIM had some issues. I would head over to your carrier and get a free sim replacement. It could be a phone or SW issue, but the Sim is my first guess give my experience

Alerts only working half the time, phone only rings half the time on incoming calls,settings all ok

my alerts for text messages, vip emails and voicemail are only sounding half the time and same with phone ringing on incoming calls...have checked settings, all are ok, have powered phone down and back up..any suggestions why i dont get alerts and phone ring all the time?

You can use http://support.apple.com/kb/ts5180. if that does not work you have to do repair.

Possible Bug !? Incoming FXO Call Reboots all the phones !

System is simple enough.
3xSPA303G phones. 2xFXO trunk. 1xSIP trunk.
Nothing else !
Incoming call from FXO line goes to extension 101, she starts to talk than after a few seconds, the voice goes away. When she hangs up, all the phones reboot. Reason of reboot shows "SIP triggered" on all phones. This happens all the time and everytime there is a call from FXO.
Also when there is an incoming call from the FXO line and is forwarded to again ext 101, but Extention 100 <grpick> the call, there is no problem !
Logs are attached.
This problem is killing us. Someone please help !
Anyone ?
Cisco ?

Hi Dogus,
Could you please contact the Small Business Support Center at the phone number listed (Please pick the appropriate phone number in your region) in the link attached? One of our engineers should be able to assist you with this issue.
http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
Best regards,
Wendy Yang

PAP-2T, make incoming calls ring in both phones/Lines?

I have a PAP-2T. On this device I have connected two different phones, one connected to Line 1 and the other to Line 2. I have one SIP account with my provider. My provider has configured my account so that I can make two concurrent outgoing calls. My Lines are configured as the following;
Line 1:
Proxy: xxxx.sipserver.xxxx.xx
Outbound Proxy: <blank>
Register: Yes
Register Expires: 3600
Use Outbound Proxy: No
Use OB Proxy In Dialog: No
Make Call Without Reg: No
Ans Call Without Reg: No
Line 2:
Proxy: <blank>
Outbound Proxy: xxxx.sipserver.xxxx.xx
Register: No
Register Expires: 3600
Use Outbound Proxy: Yes
Use OB Proxy In Dialog: Yes
Make Call Without Reg: Yes
Ans Call Without Reg: No
Now, when I receive an incoming call, the phone connected to Line 1 rings. If I configure Line 2 like this,, Ans Call Without Reg: Yes,, the phone on Line 2 rings but not the one on Line 1.
My question is,, can I make both phones ring when I receive an incoming call?
If so, how do I configure the ATA to make that happen?

Cat2k1 what kind of probs do you hve with your phones ?
- assume it's a DECT phone, try to change the ring voltage to 75V and ring waveform to trapezoid - this works better with problematic DECT phones
- assume you're having an old analog phones, make sure the PAP2T's Line1 socket is only connected via 2wire interconnect cable (4wire cable on Line1 plus certain analog phones is a trouble-maker)
- assume you use multiple analog phones on one line, you may consider increase the FXS power from 3 to let's say 5
- assume you're having an old analog phone, it's ability to ring (if all the SIP comm works OK) is also affected by the FXS port impedance which must (shall) fit the phone's one.
====
On the other hand, shall you have problems with SIP communication between PAP2T an SIP operator, you shall enable NAT traversal and NAT keeplalive for the first on PAP2T settings
Message Edited by Scorpio-cz on 12-24-2008 10:50 PM

What happened to the "DECLINE" button for incoming calls? All I get is Remind Me, Message and Slide to Answer. Where is the RED DECLINE button?

iOS7...incoming calls missing RED Decline button? Where did it go? All I get is Remind Me, Message....and Slide to Answer on the bottom.

@gkovach - Have you tried resetting your phone, Hold both Home and Power buttons down until the Apple logo appears and wait for phone to reset itself.
If this doesn't help you can try resetting all settings, Settings => General => Reset => Reset All Settings. You won't lose any apps, data, music, photos, etc. But you will have to go back in and reset all the setting that you changed from the factory defaults.

Lync 2010 Incoming calls are all Anonymous - RCC CUPS

We currently have an integration with Lync 2010 and a Cisco Cups.
Call control and presence are working fine, however it seems the Incoming Caller ID is not being passed to Lync. We can see the caller id on the Phone, but receive "Anonymous Caller is Calling you" on the Lync Toast.
Any ideas what I can check to troubleshoot this?

Hi,
Please make sure you have the normalization rule which converts the user's telephone number field from AD into the E.164 format.
Kent Huang
TechNet Community Support

HT201401 Incomming calls always on speaker phone mode. How do I change to normal phone mode?

When answering phone for incomming calls, the phone is always in speaker phone mode. How do I return the phone to normal phone mode?

Check Settings>General>Accessibility>Incoming Calls (in the Physical & Motor section). Make sure this is set to Default.

My Iphone isn't getting any incoming calls at all. what should i do?

So today i found out my my Iphone 4 has stopped be able to get incoming calls. the id doesn't pop up when someone calls me, my phone doesn't ring and theres no missed calls either. what can i do to fix this?

Contact your phone carrier. See if they can resolve the issue.

HT4061 my iphone has stopped ringing out and no incoming calls but all mobile services and i messages working

my iphone 4s has stopped outgoing calls, stopped incoming calls also normal text messages, i can get mobile internet viber, watapp and facebook and twitter , can anyone tell me what is wrong?

Something is wrong in the provisioning of your account, or your carrier has a local outage. Either way, contact your carrier.

Separate Recents into incoming and outgoing calls like all other phones!

please allow me to view only incoming or only outgoing calls
add a filter
create separate lists
whatever it takes
no more apologists please
this is a simple, reasonable change
won't break current users
will please many

FYI - this is a user to user help forum only. These discussions are provided and moderated by Apple, and certainly there are some Apple employees who peruse these discussions on occasion, but each post and thread here is not read by a moderator or by any Apple employee.
If you want to ensure that your feedback is at least forwarded to and read by the appropriate Apple personnel but with no guarantee that your request will be implemented by Apple anytime soon if ever, you should use this link instead.
http://www.apple.com/feedback/iphone.html

No incoming calls at all Linksys phone adapter SPA2102

Similar Messages

Maybe you are looking for