Offline material is present in this export...

I have created a sequence and want to export it. When I got to File-->Export, I got a message, "Offline material is present in this export and will be encoded using the Offline Media graphic." I clicked OK and the export started. Two hours later it ended but there was no file (.mov) to be found. I don't know what offlilne material is being referenced. I have looked at each clip and can find no problem. All of the clips appera to be online. Can anyone help me to find the offending "ofline material"?

"Off line" according to some on members this forum refers to low rez files used in editing instead of original source files.
But in your case...Adobe refers to it as files that are not linked and located by the Project
Go through the project bin where you imported your source files and there is a column that will tell you which files are "off line".
You need to locate and link to them.

Similar Messages

"Offline material is present in this export and will be encoded using the offline media graphic"

This comes up every so often with my renders. I have a 28:30 minute project that is 100% complete. All the files are present locally, and nothing shows as offline or missing. I've gone through the final sequence frame by frame and NOTHING is offline or missing. But when I want to send it out to export, I get the message above in the title.
What's strage is if I ignore it, then sometimes the final render WILL have display the offline graphic even though it didn't display as such in the Premiere timeline.
Often, restarting Premiere and reopening the project irons that glitch out just fine, but I have one particular project that seems to do it every time. I've tried the "import into a new project" trick, but with no luck.
Clueless in Exportville

Hey Guys,
Anybody find a solution to this yet? I am working with Premiere Pro cs5, working with r3d footage, and am having the "offline material is present" error pop up when I try to export using adobe media encoder. Prior to that error box popping up, there is another dialogue box that says that premiere has detected that there is an update to media encoder, I am running media encoder 5.01 and tried to update it but it tells me all files are up to date.
Anyways back to the problem, there is only one shot that is affected and is rendered with the offline media image( this clip also happens to be a different colour(green or teal) than the other clips in my sequence(which are blue or greyish), not sure if this is an indication of anything. I reimported the clip, and re did the edits and then exported just that new small section to see if the error would happen again,this time however, when I did the export, instead of "queue", I just hit "export" ,and the export happened without media encoder actually opening. The file came out fine,even though I had the offline media present pop up, the video was all good. I know I changed a couple of variables in that troubleshooting, so now I am trying the entire sequence with the "export" button instead of "queue" button in the media encoder pop up box, hopefully that will help. The only downside is that it seams like it takes way longer to export this way than in the queue.
I'll report back to let you know if that helps and if I can reproduce the error with the "queue" button.
EDIT
Both exports worked, so it must have been due to the re importing and re editing of the clips, however I still get the error message "offline material is present..." I guess I'll see what happens next time I do an export. Cross my fingers.

"Offline material is present" Premiere Pro CC PluralEyes 3

Hi!
I'm new to both Premiere and to PluralEyes.
I'm editing a multicam concert video.
When trying to export it I get the message "Offline material is present in this export and will be encoded using the offline media graphic". Even though there is no red offline media gaps, and all the files in the Project 'table' are shown as online.
Could someone tell me what I did wrong with my workflow?
What I did:
Added video files into PluralEyes, synced them there, exported Final Cut Pro XML for Premiere to my desktop.
In Premiere Pro CC, imported the XML file, dragged it to the timeline to start the sequence.
Started editing, everything was fine until I decided to check how it exports. When clicked on File>Export>Media the message about the media being offline appears.
After this I imported all the video files one by one to see if it changes anything but it didn't.
HELP

I don't think you will see a red line. A red screen that says 'media offline' yes, but no red line. The clip that is off line shows up in my timeline as red, but not the multicam sequence that one would want to export, but the multicam source sequence.
I do not use PluralEyes because rather manually sync then use that - and then when Premiere CC came along, it is able to do the sync'ing by audio no problems (as long as your audio is good).
I won't be able to tell you what you did wrong with your workflow - only guess.
Guess #1 - did PluralEyes change a file name?
Guess #2 - Finall Cut Pro XML have a file name change?
I don't know, pretty lame guesses as I'm starting to draw blanks in thought because you edited and everything was fine until you go to export.
If you are in Premiere CC have you considered using its own syncronization?

Offline Material Message when trying to Export

PP CC 7.1
Win 7 Pro 64
I am trying to export a sequence and whenever I try to export it I receive the "Offline material is present..." warning dialogue. I'm well aware of what offline material is, how to relink, etc. I visually inspected every single piece of media in the project and every piece of media is online.
I exported the sequence anyway and when I played it back all of the media was in the final output file.
Is there a way in the project to search for offline content? I don't think there is but figured maybe someone else has encountered this and/or knows of a resolution.
I would like to locate the media (if any) that Premiere is saying is offline thus throwing the offline material warning.

I was referred to this page by a link in the NewBlueFX support forum (http://support.newbluefx.com/newbluefx/topics/titler_pro_2_premiere_cc_on_windows_7_titles _ok_on_timeline_but_show_up_as_media_offline_in_render?utm_content=reply_link&utm_medium=e mail&utm_source=reply_notification&reply%5bid%5d=14012934#reply_140129340).
I think there is a confusion / conflict in advice here. The thread starts with the tile including "Media Offline" messages and farther below that in the proposed resolutions - a suggestion is promoted to resolve "Media Pending" messages - and as far as I am aware these are different and show in different places..?
"Media Offline" messages as put forward to be the issue are happening for me at the export to Media Encoder initiation. Inspecting all content within the project - nothing is listed as offline or missing and certainly opening the project no media is pending.
I am not a seasoned pro - and am in my first year with PP - so please don't skin me alive if I have this wrong...

Media Encoder Offline Material (that is present) and constant conforming in each PP CC open.

Hello everyone,
I have a project with several sequence that I have been working for a long time (multicam basically)
Every time I try to render/encode any of the sequence the Media encoder is giving me a:
"Offline material is present in this export and will be encoded using the Offline Media graphic"
And of course thats not useful at all
Exporting the sequence, manually without the media encoder, give me a good result.
I tried with Premiere Pro CC v7.2.2 and CC 2014, and the behavior is the same.
I also tried to offline the media and link it back again, and the issue stays.
All the media is on a local hard drive (not USB/network)
Another weird behavior, is that every time I open this project, the conforming task starts all over again (also in both PP CC versions). I also, attempted the "Save cache close to the source…" setup, but the results is the same. It conforms every time I open the project (I can see the cache files created in the file system)
This conforming takes a lot of time and is a pain in the ***.
Any recommendation on how to troubleshoot this?
I need to create the final videos soon, and doing it manually (without Media Encoder) is insane (probably a week).
Regards,

Hi guys,
As there was no reply here, I tried to open a case with Adobe, but the guy from the support chat had no idea.
I was in there 2 h, and it only asked:
"where do you have all the media files saved?"
"Ok. Are they linked?"
This was actually answered on the initial problem description.
and after the last question, it just to rapidly close the chat session, and leave me with no answer.
Can anyone point me out how should I address this problem?
Whats the best way to get support from adobe (I'm a CC user)
Regards,

How do I find the "Offline Media" or otherwise fix this?

When I try to encode a particular 30 minute timeline (I have successfully encoded other shorter timelines for Blu-ray before, in between, and after getting errors on this timeline) I get this error message - "Offline material is present in this export and will be encoded using the Offline Media graphic". I have spent hours going through the timeline frame by frame and cannot find any "offline material." As far as I can tell nothing is offline.
Presumably, Premiere Pro "knows" what is offline. Is there any way to get Premiere Pro to indicate to me WHAT it "believes" is offline and WHERE on the timeline it believes that material is?
Yesterday, even though this error appeared, I successfully encoded this timeline for DVD. It encoded fine and a frame by frame examination of the encoded video by two people did not find any sign of "the Offline Media graphic" or any sound problem.
I decided the error message was itself an error and have spent nearly all day yesterday and today trying to encode the timeline for Blu-Ray. I have tried the unmodified AME presets "H.264 Blu-ray" and "MPEG2 Blu-ray". Both generate the same error message -- "Error compiling file. Unknown error."
I have tried to EXPORT it directly from Premiere Pro and from an AME QUEUE. The result are exactly the same either way.
The encode appears to proceed normally, but after about
I am working on a 2 x 2.4 Ghz Quad-Core Intel Xeon MAC running with a OSx (10.8.5) with 28 GB of 1066 MHz DDR3 RAM. It has an nVidia graphics card, but at the moment I can't get this box to show me which one, so I will send this message now and update that bit of info if someone requires it.

WELL... that was weird. Thank you all for your advise, but it seems I was mislead by Premiere Pro, so I must apologize for unintentionally misleading you.
I STILL get the error message - "Offline material is present in this export and will be encoded using the Offline Media graphic".
And after following the advice I got from Michael MTT and checking every single one of the dozen of offline clips in the project... I know absolutely that there is not a single offline clip in the timeline I'm working on and that the error message is indeed a mistake by Premiere Pro.
But the solution to the "Error compiling file. Unknown error." message turned out to be truly weird. It was generated by a corrupted video effect (color correction) on a 2 second clip.
As I mentioned, I also work on an Avid system and when a timeline on the Avid has this sort of problem I do a "video mixdown" which PP calls "nesting". Based on the success of that procedure I decided to try nesting all the video tracks in this troublesome PP timeline. That turned the render line above of the timeline entirely RED. So I did a RENDER ALL (is that what it's called?) and about a quarter of the way through the timeline, up popped "Error compiling file. Unknown error." The rendered line was green up to a point and then red. Finally, I had a place to look and what I discovered when I did was that when I played through that part of the timeline it was holding the previous graphic as a still through the clip with the corrupted effect on it, but the criminal clip was not being played. I dug around, found the corrupted effect, which was the third of three identical color corrections applied to that clip. I deleted it and POP the everything displayed and rendered and encoded perfectly.
Thanks again all.

Cannot install drivers. No Intel(R) Adapters are present in this computer

Cannot install drivers. No Intel(R) Adapters are present in this computer
Cannot install drivers. No Intel(R) Adapters are present in this computer
Reads the error message I purchased an RaLink USB Wireless adapter IEEE 802.11 b installed in an XP Pro system, an Intel D925XEBC2 MB with A P4 CPU 3.80 GHZ
I have 4 gigs of RAM installed but it reads only 2.87 RAM on system properties
I installed the RaLink Drivers and the Ralink interface. I get a strong signal and see that the wifi is there but cannot connect. The 1394 Net adaptor #2 is showing as is the USA wireless card
I was asked to install the PIN which I assumed meant the network security but my keyboard will only input numbers not the letters, otherwise the keyboard operates properly on notepad but not on the RaLink software
Under other devices it shows both the Ethernet controller and the Network controller with a question mark "?".
I have tried uninstalling and starting the computer several times but they will not install correctly.
The windows interface shows no wi fi system at all. After going back and forth now both windows and the RaLink interface shows no wifi system.
When I went to https://downloadcenter.intel.com/detail_desc.aspx?agr=Y&DwnldID=18717 and downloaded the 32 bit file and tried to install it I got the error.

Hi there,
you're in the wrong forum, but I'll try to guide you.
(a better forum for your question would likely be this:
http://social.answers.microsoft.com/en-us/windows/forum/networking?tab=Threads )
Your RALink wireless adaptor is not manufactured by Intel, that's why Intel driver download won't help you.
You need to go here (RALink is now Mediatek) to get the drivers for your adaptor
http://www.mediatek.com/en/downloads/
Good luck! :)
Don
(Please take a moment to "Vote as Helpful" and/or "Mark as Answer", where applicable.
This helps the community, keeps the forums tidy, and recognises useful contributions. Thanks!)

About 1 year ago, I can not access the App Store. The message that appears is: "One Moment Please. Connecting to the iTunes Store. Loading ... I've tried all the aids presented in this and other forums and nothing solves. iTunes connects normaly...

About 1 year ago, I can not access the App Store. The message that appears is: "One Moment Please. Connecting to the iTunes Store. Loading ... " I've tried all the aids presented in this and other forums and nothing solves. iTunes connects normaly...

Your profile indicates your Mac is running v10.7.2
If that is correct, updating your system software may help.
Click Software Update from the Apple menu.
Restart your Mac after updates are installed then try the App Store.
If you can't update that way, there's a workaround.
Install the OS X Lion Update 10.7.5 (Client Combo)
Then restart your Mac and try the App Store.
messaged edited by: cs

E.     They are getting material from customers. This while receipt will be non

Hi Friends,
                   1. They are getting material from customers. This while receipt will be non valuated. But they want to avail CENVAT on this.
                    2. In some times, Supplies from customer are delayed.So they are adjusting this against their stock.and after recieving, they are taking back their stock.how this can be mapped?.

Hi JPAnnett
I can investigate what has happened for you.
Send me an email using the contact the mods link in my profile you will find it in the section 'About Me'.
Thanks
Stuart
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry that we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

How to export an eloqua report to a (ftp) server and schedule this export

I would like to export an eloqua report to a (ftp) server and schedule this export. I want to pick this report up by another tool like Qlikview.
Liesbeth

if it is something to do with having report admin rights is there a way to still export report data without these admin rights? is it possible to just export report data as activity data in the normal import/export section within the setup menu? is there a problem using filezilla client and oracle eloqua together for this?

The table tablename is not present in this descriptor.

Hello, I'm using JDev & TopLink 9.0.3. I get the following descriptor errors. I'm not sure what they mean or how to resolve it. I re-mapped the Advisor descriptor, but with same results. Thanks.
EXCEPTION [TOPLINK-93] (TopLink - 9.0.3 (Build 423)): oracle.toplink.exceptions.DescriptorException
EXCEPTION DESCRIPTION: The table [advsr_demographics] is not present in this descriptor.
DESCRIPTOR: Descriptor(com.diyh.model.javabeans.Advisor --> [DatabaseTable(party), DatabaseTable(advisor)])
EXCEPTION [TOPLINK-41] (TopLink - 9.0.3 (Build 423)): oracle.toplink.exceptions.DescriptorException
EXCEPTION DESCRIPTION: A non-read-only mapping must be defined for the sequence number field.
DESCRIPTOR: Descriptor(com.diyh.model.javabeans.Advisor --> [DatabaseTable(party), DatabaseTable(advisor)])

I figured it out. My Table Reference in the parent descriptor was reversed. I removed it and created another reference with the source from the parent descriptor and the target from the child descriptor.

CMNS support is not present in this image

Hi,
We are using a C1721 router to connect a X25 line to an ethernet port. We need to enable CMNS and we get the following error:
GDM_Cisco#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
GDM_Cisco(config)#interface fastethernet0
GDM_Cisco(config-if)#cmns enable
CMNS support is not present in this image
This is the device information:
GDM_Cisco>show hardware
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-ADVSECURITYK9-M), Version 12.3(15), RELEASE SOFTW
ARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Tue 24-May-05 21:33 by ssearch
Image text-base: 0x8000816C, data-base: 0x81012AF4
ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
ROM: C1700 Software (C1700-ADVSECURITYK9-M), Version 12.3(15), RELEASE SOFTWARE
(fc3)
Any help would be useful.
Regards,
Fernando L

Dear sir, you should throw cisco from the top of the mountain !
ilker

Latitude e7450 - Repeating Keys/Debouncing Issue is present in this model too

Not sure how to get attention to this, as I do not think Dell is aware of this problem since this model was only released a month ago. The repeating keys/debouncing issue described here , is present in this new model Latitude e7450 in both bios A00 and A01. Please make this bug known, so that Dell is able to fix it in a bios update!

So, I also found and posted in this thread about the issue with the E7450
and basically that is the aggregation of all the posts on this repeating keys/debouncing issue on ALL affected models. Honestly as a developer, I'm pretty shocked at how bad Dell support really is. I've been lucky enough to never have any hardware issues until now...
They chose to have a forum for their customer service, fine; that works with many other companies. But they should have at least split the forums into laptop series,by model number, have a bug tracker and paid more than 1 guy to relay issues to the engineering team.. This is ridiculous and utter chaos reading through these threads and it is enough to make me question buying a high priced Dell ever again. Like many people I went with Dell Latitude after Lenovo created that awful macbook-like clickable touchpad, but it looks like their 2015 models are bringing back hardware left/right click buttons again so that might be my next purchase.

I am getting this certificate error: The security certificate presented by this website is not secure. .

I have installed the https certificate and I get this error when browsing to my server using https: I can get to the server in FireFox but not in IE. I tried disabling add-ons, compatibility mode, but it did not help. There is not an option
to continue on to the site, only option is to close the session.
We are running IE11, the server I am trying to reach is running on VMWare. We have all recommended updates installed.
There is a problem with this website’s security certificate.
The security certificate presented by this website is not secure.
<id id="securityCert2">Security certificate problems may indicate an attempt to fool you or intercept any data you send to the server.</id>
We recommend that you close this webpage and do not continue to this website.
Thank you

Hello Dean Wainwright,
Do you mean after installing the certificate, you still can’t visit the website?
Please refer to the following blog to install the certificate to Trusted Root Certification Authorities and then check if the issue still exists.
http://blogs.technet.com/b/sbs/archive/2007/04/10/installing-a-self-signed-certificate-as-a-trusted-root-ca-in-windows-vista.aspx
Best regards,
Fangzhou CHEN
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

No material group assigned to this value

Hello, I am trying to add new value to a purchasing organization in extended attributes about product categories.
When I add new value system throws an error message: "No material group assigned to this value", this material group is created in R/3 backend but not in SRM. How can I transport this value to SRM? Only 3 values not all data about material groups.
Thanks in advance
Rosa Rodríguez

Hello, I have this in the transactions that you mentioned:
r3ar2
Request Name: ESN
Adapter Object: DNL_CUST_PROD1
RequestType: Request: Objects could be loaded from R/3 backend / CRM DB
Use One with mark
Table: T023T
FieldName: MATKL
I/E: I Inlusive defined set/array
Opt: BT
Low and High: range of material groups that I want to replicate.
I put in transaction R3ar4 the request name and when I check on transaction r3ar3 this transaction is running and take long time .... I think there is a problem because are only 3 product categories
What can I do to check if the system failed or something similar?
Thanks
Rosa Rodríguez

Offline material is present in this export...

Similar Messages

Maybe you are looking for