Operation time

Dear Gurus,
I want to set up the following process :-
A painting machine takes fixed 2 hr to get loaded with job and heated
After these fixed 2 hr only it starts to generate o/p --> pained job
I have created 2 WC for this
WC1 - M/c time =120 min=2 hr (How to keep it fixed ??)
WC2 - M/c and labour time correctly set up
Issue is that i want to keep the WC1 time fixed =2hr whatever be the order quantity. When Routing is read the scheduling of WO should take WC1 time as 2 hr and WC2 timing may vary according to the order quantity.

Shalini,
No need to maintain 2 separate work centers for this
Create only one work center with machine & labour category
In the routing assign this work center
In set up time give 120 mins
Machine time & labour time as applicable
Now only your machine time & labour time will proportionately increased with the qty
Set up time will remain constant
This is based on the formula- defined in configuration-Tcode <b>OP21</b>
Hope this is useful
Revert back if you have any further queries
Reward points if useful
Regards,
SVP
Message was edited by:
        SVP

Similar Messages

  • Operation time calculation based on partial confirmation.

    Dear FRndz,
    Pls help me out with following scenario.
    1.Am defining a task list in which am mentioning the set up time as 30 min & operation time as 10 Min per peice of finished goods.
    2.Creating a production order for 10 Pieces.
    3.Am doing partial confirmation of 5 Nos.
    At this point of time I want the system to calculate the timings appropriately for 5 peices.how do I configure it?....
    REgards,
    Srini

    Dear,
    Go to TCODE :OPK0
    This is the single screen entry for confirmation.
    Select the profile you are using & in the tab Defaults
    go to section default values & select "IMMEDIATE PROPOSAL"
    in both "quantities & services"
    It will definitely work.
    Regards,
    R.Brahmankar

  • Operating Time Machine over a remote Back to My Mac connection is a challenge -- can I do restores in Terminal?

    When operating Time Machine remotely via Back to My Mac (and by remotely, I mean from Illinois to Ohio ), seeing your remote mouse cursor is largely a no-go, even in Lion. It simply does not get displayed, with very minor, flickering exceptions.  Certainly it becomes impossible to operate the Time Machine's Finder window in any mouse-clicking way.  I can barely operate the CANCEL or RESTORE buttons, and that's if I help myself by mousing over from outside the Screen Sharing Window, and kind of estimating if I am over the button area.  Similarly, I can get the mouse to give me some approximate date in the backups progression.  But the way to select a file, I found, is through arrow-keys.  I can get to the right directory before starting the Time Machine, and I can navigate to the correct file with much delay using the arrow-keys.  In short, it's a major freaking pain, because of all the lag and invisible mouse. 
    But I was able to do what I needed, given enough pain and perseverance.
    Question:  Given the impoverished visuals for mouse operations, is there a way to do this on the command line, not through the moving galaxy syntactic sugar that just gets in the way?  Can I run the whole restore operation in Terminal?  Of course, still via Back to My Mac, because I don't know how to get to the remote iMac in any other way remotely, given that it sits behind a cable modem and a Time Capsule router with NAT.  And I don't want to set up port forwarding, if I don't have to.
    Thanks for reading, and I'll take your considered expert advice.
    -- Marek

    Well, I have now reformatted/partitioned my poor WD Elements 2TB drive about a dozen times as well as restarted my 1TB Time Capsule so many times it's no wonder it's as confused as I am! <G>
    Last night, at your suggestion, William, and in respect for your continued support, I tried creating two 1TB Mac OS Extended (Journaled) partitions on the WD external USB drive, both with GUID partition tables. Both volumes mounted to my laptop's desktop flawlessly and without issue.
    Once the external drive was connected to the Time Capsule, however, it was a crap shoot as to whether or not the drive was recognized at all, reporting a problem with the disk, or, even at one point, mounting one of the two volumes but not both. <sigh>
    I read somewhere on the Internet that you need to restart the Time Capsule for volumes on an external USB drive to be recognized.
    So I tried that. I connected the freshly partitioned/formatted disk to the Time Capsule and restarted it. This succeed in removing the issue of reporting a nameless drive with a capacity of 0MB. It then reported the drive with its correct name but would not recognize whatever volumes in whatever partitions that particular crack at it contained with the exception of the once, as I mentioned above, when only one of two volumes mounted correctly and was listed with the right name and capacity on the Time Capusule's Setup's Disk tab.
    At this point I have given up on my goal to use the external drive with Time Machine to back up my Macs or to hope I will ever be able to see its contents remotely via Back to My Mac. All I would like to do now is simply find a reason why I can't get it successfully connected and playing nice with my Time Capsule in the first place!
    Any further suggestions or advice as to what steps I might take next would be greatly appreciated.
    Thank you all.

  • The wait operation time out

    Dear all,
    I am facing one problem with my user pc "The wait operation time out"
    ERROR= 
    Aconnection was successfully established with the server. but then an error occurred during the pre-loging handshake. (provided , SSL providing error-0 , The wait operation time out microsoft SQL server error- 258.
    my user-pc use windows 7 and connect VPN by using "Sonic-wall" we connect successfully and get my remote server IP ping reply but when try to access remote server database that time I am getting this error
    At the same time using same network and id can connect the server from vpn and access database from other
    system.
    please help me sort it out this issue. 
    thanks 
    sajal 

    Hi Sajal,
    It is possible that remote machine(server) is up but please check whether database server is up or not.
    Please contact database administrator to know the status of database. This will help you to know the cause.
    If database is down you cannot connect it.

  • Ssh operation time out

    In my office, I have a MacBook and a Mac Pro. I tried to ssh to the Mac Pro from the Macbook and got the "operation time out" error. I am able to ssh to a Linux box from my Macbook.
    Anybody has encountered this? Thanks.

    I solved the problem.
    I should select "set access for specific services and applications" in Preferences/Security/Firewall.

  • Update operation times in routing

    hello all,
    I need to do a mass change on routing in order to update operation times.
    I'm trying to find a BAPI/function to do this but without any success.
    It's not possible to do it with call transaction CA02 because depending on the material I can have one or several operations.
    I'm currently testing function CP_BT_PLPO_READ_WITH_INDEX and CP_DI_OPR_UPDATE but without any success (..and I'm not sure if it will feed my needs).
    Any help/suggestion is welcome !
    Thanks

    If it helps you, here is the code that loads our bdc. it might help you to walk through it.
    PS, we use SM35 as opposed to call transaction for ours as we load the data from excel, and have upwards of 8000 to 10000 routings updated at one time. We let them change only the run and setup times.
    * Initial screen
        perform bdc_screen using 'SAPLCPDI' '1010'.
        perform bdc_field using 'RC271-PLNNR' data_record-plnnr.
        perform bdc_field using 'RC271-PLNAL' data_record-plnal.
        perform bdc_field using 'BDC_OKCODE' 'XALU'.
    * Next screen
        perform bdc_screen using 'SAPLCPDI' '1400'.
        perform bdc_field using 'BDC_OKCODE' 'OSEA'.
    * Next screen
        perform bdc_screen using 'SAPLCP02' '1010'.
        perform bdc_field using 'RC27H-VORNR' data_record-vornr.
        perform bdc_field using 'RC27H-ARBPL' data_record-arbpl.
        perform bdc_field using 'RC27H-WERKS' data_record-werks.
        perform bdc_field using 'BDC_OKCODE' 'ENT1'.
    * Next screen
        perform bdc_screen using 'SAPLCPDI' '1400'.
        perform bdc_field using 'RC27X-FLG_SEL(01)' 'X'.
        perform bdc_field using 'BDC_OKCODE' 'VOD1'.
    * Next screen
        perform bdc_screen using 'SAPLCPDO' '1200'.
        perform bdc_field using 'PLPOD-LAR01' 'SETUP1'.
        write data_record-vgw01 to charquan.
        perform bdc_field using 'PLPOD-VGW01' charquan.
        perform bdc_field using 'PLPOD-VGE01' data_record-vge01.
        perform bdc_field using 'PLPOD-LAR02' 'LABOR1'.
        write data_record-vgw02 to charquan.
        perform bdc_field using 'PLPOD-VGW02' charquan.
        perform bdc_field using 'PLPOD-VGE02' data_record-vge02.
        perform bdc_field using 'BDC_OKCODE' '/3'.
    * Back
        perform bdc_screen using 'SAPLCPDI' '1400'.
        perform bdc_field using 'BDC_OKCODE' '/11'.
        perform insert_bdc.

  • Dependent requirements distribution via Operations time

    Good Day SAP expert!
    Can we set up the system (Distribution key) so that Dependent requirements distribution will be based on Operations time instead of just Order start date and Order finish date and spread evenly?
    For example, my planned order starts at 23:00 on first day and ends on 23:00 the 2nd day, the dependent requirements of the component will be 4% on 1st day and 96% on 2nd day or at least round to 10% increment. Please advise.

    Reden Manguerra,
    You want system to dynamicaly split the component allocation percentage depend upon the requirement dates and time remaining in shift , its not possible.
    if you have fix timings or the splits with fix percentages then you can acchive it by maintaining operation same as number of time you need split and you need to maintain same compoenet on different possitions of BOM so that you can allocate it to respective operations and in item details screen you need to maintain floats between operations.
    Check and revert back for further discussion.
    regards
    Ritesh

  • Operation time at the time of confirmation

    Hi Guru's,
    I want a report on  operation time as per routing  and  actual time of operation entered at the time of
    order confirmation . Any Tcode could you suggest where i can get operation time ( asper Routing ) and
    actual time of the operation against order . I have checked coois with different layout it is available but
    i want report on all the order number also checked in AFVC table not getting  .
    Please suggest  some Tcode / report where i can extract this .  points will be awarded for the suitable
    answers.
    expecting your reply at the earliest,
    regards,
    vimal

    Hi Guru's,
    I repeat this question because i did not get  answer and people are points oriented and answering
    the questions which are repeated no of times. Please take it serious and  this time i anticipate that
    PP guru's will revert  with solutions .
    I want a report on operation time as per routing and actual time of operation entered at the time of
    order confirmation . Any Tcode could you suggest where i can get operation time ( asper Routing ) and
    actual time of the operation against order . I have checked coois with different layout it is available but
    i want report on all the order number also checked in AFVC table not getting .
    Please suggest some Tcode / report where i can extract this . points will be awarded for the suitable
    answers.
    expecting your reply at the earliest,
    regards,
    vimal

  • Error " No working/operating time maintained in work center for scheduling"

    Hello Friends,
    When i am scheduling the planned order than in scheduling log, system throwing the error "No working/operating time maintained in work center for scheduling".
    Message no. C7014
    But in workcenter, i have attached the grouping and in interval and shift for the available capacity 1, i have maintained the shifts.
    According i can see the capacity on that workcenter in CM01.
    Same error i am getting when i am scheduling the routing and check the scheduling log.
    Regards,
    Jitendra.

    Hi
    Have u checked , to maintain the time required to perform the activity in the work-center?
    please check, i think, we have to maintain for each activity type.
    regards,
    rasika

  • Operating time error in work center

    while creating production order, i am getting the below error
    "No working/operating time maintained in work center for scheduling"

    Hi,
    Check following thing,
    1.Check whether you have maintained time in capacity tab.
    2.Check scheduling tab formulas.
    3.Check in control key whether scheduling has been activated.
    The error shows below message
    C7014 - No working/operating time maintained in work center for scheduling - C7 014
    Vendor Master (General Section)   General Material Data  
    This documentation is copyright by SAP AG.
    Diagnosis
    No operating time has been defined for the work center specified in the operation.
    System Response
    Scheduling is carried out on the basis of an operating time from 00:00 hours to 24:00 hours.
    Procedure
    Maintain the operating time in the work center.
    So maintain correct time in capacity tab
    Regards / US
    Edited by: Umashankarpmgl on Jan 20, 2012 2:58 PM

  • ORA-12535 TNS:Operation time Out and ORA-12154:TNS Could not resolve servic

    Greetings!!!
    I have installed my Oracle Database 10g & Developer Suite 10g in Windows XP Pro Machine. Oracle Application Server 10g is also installed in Windows 2003 Server machine.Both machine have different domain.When using Form Developer Suite OC4J to run my form program, i can connect to the database properly run the form perfectly.
    Problem encountered.
    When I tried to run the form using Application Server 10g(installed in Windows 2003 Server), I got an error ORA-12154:TNS Could not resolve service name when connecting to the database and I got an error ORA-12535 TNS:Operation time Out when using TNSPing. I checked both the configuration of TNSNAMES.ORA(database & Application SErver) using the same port & service name but still got the same error.
    Hope somebody can help me out there...
    Many thanks in advance.
    Regards,
    BTF

    I have seen this before with my setup, I found that I had to go into the net configuration assistant, and change my host name to the fully qualified name, example: my compuer name is computer1, I had to enter in computer1.OIT.Docfinity.com for it to take. That has always gotten me past that TNS error, just my 2 cents, hope it helps.
    keep on keeping on.

  • What is the maximum operating time of the airport and airport extreme?

    What is the maximum operating time of the airport and airport extreme? Can I leave it on for long periods of time, like never turning it off? Will it affect the performance of the said products?

    Apple does not include an "Off" button on the AirPorts since they assume that you will leave it on all the time, like you would a modem.
    If you are going to be gone for a week or two, it might make sense to power everything off during that time.
    Otherwise, leaving the device(s) "On" actually results in less stress on the device that constantly turning it "Off" and "On". In other words, odds are the device will last longer if you leave it "On" most of the time.
    Apple does not publish a life expectancy for the devices, but 5-7 years...on average....for a modem or router is about right....my opinion here.

  • Confirmation operation time to be displaysd when it comes in betwn holidys

    i am doing one confirmation ( co11n )  which started on saturday 17:30 pm but the wrkcenter timings are
    9:00 am to
    18:00 pm  but the operation time is of 4 hours 0:30min on saturday and remainig balance on monday with 3hr
    30 min done but in my confirmation  startdate is on saturday ( 23/05/2009 ) , 24/05/2009 is sunday and end
    on 25/05/2009  but my client want time required to complete the operation i want to get only 4 hours but when
    i see the difference between start and end it is showing sunday also to get 4 hrs where can i see the time
    completed operation in the report.
    regards,
    muralidhar.t

    Hi Muralidhar,
    You can get the deatils from the COOIS report.
    Choose Operations - Standard Layout, then change the layout and add columns Activity 1 to Conf., its unit. Similiarily add other activities too (as many you are confirming in CO11N).
    In the CO11N screen, enter the actual setup, processing times etc, you will get the actual values in COOIS then. Then you wont require to subtract the start date and time from finish to get the operation time details. Moreover these values are only for start and finish times not the operation time or activity time.
    Your operation started on saturday and ended on sunday, but actual operation time will be shown in activity time entered during confirmation.
    Hope that helps.
    Regards,
    Rohit
    Edited by: Rohit Chauhan on May 27, 2009 9:13 AM

  • Operation time in master reciepe

    Dear all,
    Where can we mentain operation time in in master reciepe.
    Please help
    San

    Hi San,
    In Master Recipe you can not maintain Activity times at Operation Level.It can be assigned at Phase Level Only.
    Regards,
    Dhaval

  • Scheduling and workcenter operation time

    HI.
    What is the effect of the capactity operation time of workcenter on scheduling of an activity ?
    BR

    Hi,
    if your work center A  is having time from 8 to 4 then available hrs in one day - 8hr ( if you are utilizing 100%)
    if your work load is 100 hrs  then it will schedule as per available hr in work center ( 100/8  + non working -days).
    for 2nd work center B if you dont mention time  that means sytem considering available hrs in one day - 24 hrs
    if you mention same work load  i.e. 100 hrs, sytem will schedule as per available hrs in One day for that work center (100/24+non working -days).
    definitly scheduling will be different  and dates will be different.
    Venkatesh

  • Sockets - BufferedReader.read() operation time-out

    Hi all,
    I'm facing some problems to receive data over socket connection from a PC. I send data via BufferedWriter, but I have time-out error (IOException: Operation timed-out) and I can't see why it happens.
    Here is part of my code:
    StringBuffer strBuffer = new StringBuffer();
              int charRead;
              File xmlFile = null;
              FileWriter fw = null;
              try{
                   if(s != null){
                        bufReader = new BufferedReader(new InputStreamReader(s.getInputStream()));
                   xmlFile = new File(fileName);
                   if(xmlFile.exists())
                        xmlFile.delete();
                        xmlFile.createNewFile();
                        fw = new FileWriter(xmlFile);     
                   }else{
                        connect();
                   //while((line = bufReader.readLine()) != null)
                   while((charRead = bufReader.read()) > -1)
                        strBuffer.append((char)charRead );
                   bufReader.close();          
                   String writeString = strBuffer.substring(4);
                   if(fw == null){
                        setErroSocket(true);
                        setMsgErroSocket("I/O Error: Erro recebendo dados via Socket");
                   fw.write(writeString);
                   fw.flush();
              }catch(IOException ioE){
                   setErroSocket(true);
                   setMsgErroSocket("I/O Error: " + ioE.getMessage());
              return xmlFile;
    If nore detailed information is need, please ask me.
    Thanks for any help !

    Hi,
    I believe I found where was the problem. I was a bit confused with setSoTimeout(), because I thought it set the limit of time for read bytes, but in fact it controls the limit of time that conection is off. Looking a little deeper in my code I saw that bytes are read, but the exception occurs the same way.
    I just need to change some things because I need a permanent client socket on-line because I'll need constantly comunication with a server application (Delphi) running on a PC. I believe that I must start with changing my ClientSocket class into a Thread.
    Thanks for your help !

Maybe you are looking for