Print Cancellation Problems

I cannot cancel a print job for my C6180. I have tried several ways to cancel the job, have turned off the printer, and have unplugged the printer. Help!

valton wrote:
I cannot cancel a print job for my C6180. I have tried several ways to cancel the job, have turned off the printer, and have unplugged the printer. Help!
Turning off or unplugging the printer will not clear job in the print queue. You do not mention what operating system you are using, in most since XP it is possible to go to the printers folder, pause the print queue and then delete print jobs in the queue.
You can also cancel a job by pressing the X button on the fornt panel of the printer.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Similar Messages

PDF printer has a problem with Safari in "Reader" mode in Windows7

As shown in the image above. When I try to use the PDF printer to print out a web page in Safari "Reader" mode, the lines near the bottom of each page get squeezed like this. There is no problem with XPS printer. I guess this problem is because of some incorrect settings in Safari or the PDF printer?
My system is Windows 7 Pro. I am using Acrobat X Pro. The page I am trying to print is http://en.wikipedia.org/wiki/Electronic_band_structure. This problem only happens when the webpage is adjusted into "Reader" mode in Safari.

Many thanks for your reply!
I am sorry, I did not make my question clear. I would like to save some web pages only in "Reader" mode, because in this mode all the advertisements are filtered out and the pages look much nicer than the origional layout.
I first let Safari to active "Reader" by clicking "Reader" button.
Then I click "Print" button and select Adobe PDF as the printer.
The problem is the PDF file has something wrong (shown above), and I would like to know how to avoid this problem.

Downloaded acrobat reader 11 onto my Mac Book Pro, it can open the file but will not print. Get a message that says PDF cannot be printed, however, I forwarded it to someone else and they could print it, no problem. I called HP and spent an 1hour with the

downloaded acrobat reader 11 onto my Mac Book Pro, it can open the file but will not print. Get a message that says PDF cannot be printed, however, I forwarded it to someone else and they could print it, no problem. I called HP and spent an 1hour with them and then called Apple support and worked with them for 3 hours. No one can figure it out. Is there something wrong with this version? the pdf was created in 2004. Do I have to pay to get Acrobat?

Let me give you a slightly different perspective than everyone else here. You are using an unsecured wireless network, which means that all your network traffic is easily available for viewing by anyone else using that network. That's bad. Very bad, for you, unless you absolutely trust everyone who lives within range of this network. So stop doing it.
As to the Mac not connecting, wireless networking is simply too complex for any reasonable answer without more information. There are many possible error points, and as often as not it's the Mac that can connect and the Windows PC that cannot. Since you can't give us any information about the configuration of the neighbor's network, and can't make any changes to it, we can't do much to help you troubleshoot it.

I am having trouble printing a PDF document. Whenever I click print nothing happens but when I am printing documents from Word, Excel etc they print without a problem. I've tried printing as image but that did not work. I uninstalled Adobe Reader XI and d

I am having trouble printing a PDF document. Whenever I click print nothing happens but when I am printing documents from Word, Excel etc they print without a problem. I've tried printing as image but that did not work. I uninstalled Adobe Reader XI and downloaded Adobe Reader X instead and that still doesn't work. I have Windows 7.

Hello,
Please follow the link to troubleshoot the printing issues with Adobe Reader:- Troubleshoot PDF printing | Acrobat, Reader.
Regards,
Nakul

When I tried to print I had problems.

I got a new Macbook pro yesterday. Brilliant!
I used Time machine to transfer everything. I'm getting used to most things but
when I try to print I had problems.
I downloaded new driver but still no go.
Help please!!!
Kathy

If you haven't done so already, try resetting the printing system.
OS X Mavericks: Reset the printing system also Yosemite

Print Color Management Problem ?

I have a print color management problem I cannot solve. It reminds me of the print color management problem I had over a year ago when the compatibility conflict between LR and MAC Leopard produced horrible prints. I have Snow Leopard now and been out of the country for some months and yesterday when I tried to make some prints the same problem reemerged. So I downloaded current drivers (and ICCsfor Premium Luster) from Epson and LR 2.6 and spent a good part of the day with Martin Evening's book. I followed (I think) his instructions to make the basic print step by step but the prints still were terrible. My problem is with the color management pop up in the print settings dialog -- it says "color matching" not color management and I cannot check either "no color management " if I want LR to control the process (Kelby) or check "color sync" if I want my Epson R800 take over. I have no idea where the "color management" pop up went. I'm clueless as usual and probably omitting a step because of frustration or brain numbness. Any help would be appreciated. WJS

The settings in Lightroom are simple. and contain in the Print Job panel in the Print module. You either select manage in printer (and then select the profile in the printer drivers) or select the profile here and then turn of all colour management in the printer drivers. The second option will usually produce the best results. What you don't want is to have the profile selected in both LR and the printer drivers, so if the driver doesn't have an option to turn of colour management then you may be forced down the first route. However it would be an unusual decision for a printer manufacturer to make drivers that can't turn off colour management, so you may wish to ask how to do it to your printer manufacturer or check the printers handbook.

I used to print my photos in my hp psc 2210 printer without any problem. Now it gets stuck towards

I used to print photos in my HP psc 2210 printer without any problem including the 8X11 enlarged photos, but now it gets caught at the end of the printing resulting in shortened images. Does it have to do with the thickness of the photo paper? It was able to do it before. Are there any adjustments to be made?
HMC

Hi,
It looks like you've tried some of the troubleshooting steps listed in this document, but there are a few more to try first. Click on the + besides the XP section and follow the steps in order. See if this helps, if it doesn't I'll look for some more.
Printer Prints Blank Sheets
Say Thanks by clicking the Kudos Star in the post that helped you. Please mark the post that solves your problem as Accepted Solution.
I am employed by HP

HP color laserjet 2600n windows 7 printer not installed problem with spooler.

My computer will not recognize my printers. Nothing new was installed, just all of a sudden, they were gone . Have installed new drivers, and had a very knowledgeable person look at it-nothing. Very frustrating. Have a program that has been on it from the beginning and now it won't work (quark). Don't know where to turn. Am doing a windows defender scan for viruses as we speak. Help!!!!!

Could be a lot of reasons. First try to print a supplies status page- If that prints with color on it, you have a driver problem.

Hp LaserJet Printer 1300 Installation Problem

I have Hp Laser Jet 1300 Printer want to plug it with Dell an Thosiba laptop. I have orignal drivers cd with it but, During Installation, its stop and gives error that Unable to install Printer.

Please check the operating system compatibility with your product and try to perform installation with latest drivers:
http://h20566.www2.hp.com/portal/site/hpsc/public/psi/swdHome/?cc=us&cc=us&lang=en&lang=en&sp4ts.oid...
Please mark the post that solves your problem as Accepted Solution
Click the 'Kudos Thumbs Up' if this was helpful. Thank You!
(Although I am an HP employee, I am speaking for myself and not for HP)

I have HP LaserJet Pro M1536dnf Multifunction Printer and my problem with eprint "Not Connected"

i use eprint but after day show in site massage state Not Connected
to solve this problem turn off printer or hp web services and tern on and it work
but same problem after some hour show not connected
how can printer connected all time ?

Hey sfareg,
One thing you need to check is if your internet connection is intermittent. If it is not, you can follow these steps to give the printer a better connection.
1. Find your printer's IP address by printing a network configuration page.
2. Type you IP address into the address bar of your web browser.
3. Click on the network tab at the top of the page.
4. Look at the left hand side and click IPv4 under wireless.
5. Change the IP settings to Manual.
6. Enter the printer's IP address, your subnet mask, and your routers IP address or default gateway in the spaces.
7. Set the Preferred DNS to 8.8.8.8.
8. Set the Alternate DNS to 8.8.4.4.
9. Click apply.(You may need to refresh the page if it says processing for longer than a min and click apply again.)
The printer should have a better connection now.
Although I am an HP employee, I am speaking for myself and not for HP.
If I have resolved your issue, feel free to provide Kudos and make sure you mark this thread as solution provided.

HP LaserJet Pro M1217nfw Multifunction Printer scaner driver problem in windows 7

I have a HP LaserJet Pro M1217nfw Multifunction Printer. Printer is ok but Scaner has problem in Windows 7 scaner driver is deleted when i try to scan it show the error " Scaner not communicate " I have to reinstall driver after few minitus again same problem . Pls advise me what is the best solution for that

Hi KrunalPatel,
I'll paste a link to a troubleshooting document below - from what I've read, it has the best chance at fixing your scanner errors, as it has the most steps to try
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c02917811
Please let me know how it goes
*** If my reply was helpful, please click on the "Kudos Thumbs-Up" on the right, as a way to say "Thanks!".
If this reply also fixed your issue - please click the "Accept as Solution" button, so that others can find the same answer. ***

Unable to communicate with printer; ad hoc problem: Photosmart 6510

I'm running windows 7 pro and I recently installed the aforementioned printer. Please help. 'HP-setup-73 Photosmart 6510,' the name of the printer, is recognized and able to be connected to in my network wireless connections. Firewalls have been disabled and Installation and network config is already set - at least to my knowledge. But when trying to print something, an error window pops up saying: "Unable to communicate with printer...If you installed this printer by IP address, please update the IP address..." That error message could be irrelavant; Perhaps it's a setting adjustment on the printer side. I don't know, that's why I'm asking. what should I do to fix this problem?

Print a Wireless Network Test from the front of the printer (probably the Network or Wireless menu). Does it indicate that your printer is connected to your network?
If so, go to Start > All Programs > Hewlett-Packard > [your printer model] > Update IP address.
If you want a more permanent solution after doing this (so you will not have to do it again), set a static IP address for the printer:
- Print a Network Config Page from the front of the printer. Note the printer's IP address.
- Type that IP address into a browser to reveal the printer's internal settings.
- Choose the Networking tab, then Wireless along the left side, then the IPv4 tab.
- On this screen you want to set a Manual IP. You need to set an IP address outside the range that the router automatically sets (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') to 250
- Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
- Enter your router's IP (on the Network Config Page) for the gateway.
- Enter 8.8.8.8 for the first DNS and 8.8.4.4 for the second DNS.
- Click 'Apply'.
Now, shut down the router and printer, start the router, wait, then start the printer.
After this you may need to redo 'Add a Printer' using the new IP address.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Hp officejet all in one printer 4500 G510n problem downloading software and driver

When i download the software and drivers for the officejet 4500, G510n, and attemp to extract the file it will not open indicating that the file is corrupt. I have tried it numerous times using both my AOL browser and Internet Explorer. Any suggestions Thank You.
This question was solved.
View Solution.

Hi @salsan,
Welcome to the HP Forums!
I understand that you are having a problem with downloading the driver for your HP Officejet 4500 printer on Windows XP. I am happy to look into this issue for you!
When you finish the download, it should show how big the file size is. Does it show that the file is 224.69M after it is finished downloadng? Perhaps, it is stopping the download before it finishes. I would recommend trying another browser such as Firefox or Google Chrome.
What version of Windows XP are you are using? If you do not know the Operating System you are using, please visit this website. Whatsmyos. Is it 32-bit or 64-bit? Is the Windows Version on My Computer 32-bit or 64-bit?
Thank you for posting, and hope to hear from you soon!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Print Paper Size Problem after Mavericks Upgrade

I migrated my Apps, Data and System Settings from a Macbook running OSX Lion to a new Macbook Pro running Mavericks.
The problem I now have is that the application 'Family Tree Maker 2' cannot get the paper size right. No matter which Paper size I select, it is shown as half size in the Application Print Preview screen and this error carries through to actual printing.
so A4 210 by 297 mm displays as 5.8 x 4.1 inches (which is Half Size).
The problem is significant because the application formats it's output to fit into half of the available space.
I have unsuccessfully tried;
- removing and reinstalling the Application.
- Adding my Brother Laser printer with the latest Mavericks compatible driver.
- Resetting the printing system.
- Repairing disk permissions
- Adding a new User Account
- Deleting plists associated with com.ancestry
iWork Pages is working correctly.
I have raised this with ancestry.com however it appears that I am the only person that has experienced this problem.
Any suggestions would be appreciated.

Problem is worse than that. Whilst the Paper is shown as half size, the family tree diagram boxes are produced twice as wide as they should be.
If I select A4 Paper, a diagram that would fit on one page is now spread across two.
If I select A3 Paper, the preview indicates the paper size as A4 8.3 x 5.8 inches however the diagram size and position on the paper are unchanged and I just get loads of white space around the outside of the diagram.
It does sound like an Application problem but it is still working fine on my old OSX Lion machine. Something has happened in the migration.

Printing/creating PDF problems with Mac OS 10.6.4 and word v.X

In my job at university I use Word 2003 (version 10) in my new iMac. Since I updated to MacOS 10.6.4 I have problems with the printing menu. That means that I can not print or convert to PDF or even generate a preview. When trying to print or obtain a preview, word freezes and I have to force quit. When trying to generate a pdf file it does, but the generated file is unreadable (it says is damaged) and word freezes again. I have played with the preferences, change user and it didn't help. I checked the Font Book and indeed they were many duplicated fonts. I sorted them out, but the problem persists. With very short files it works, but with longer ones word invariably crashes when trying to print or make a pdf. I took one long .doc file and I copied into my laptop (MacBook pro, 2008) that was running 10.6.3. I printed it and converted to pdf; no problems at all. Then, for the sake of knowledge, I updated the system to 10.4.6 and then I couldn't print or create a pdf with the very same file, so it seems that certainly the update is reponsible. So now I know cause but I can not print from any of my computers. To me convert to pdf is an important functionality so I would appreciate any help. I have some ideas: reinstall Office 2003? reinstall 10.6 from the disk (and not update)? use Time Machine to restore the system as it was before the update?
I didn't detect problems in Office 2004, or any other programs in my macs. Unfortunately, I need Office 2003 for compatibility with some other software. Thanks in advance!

I updated my MBP to 10.6.4 last night and today I was printing fine from Word 2008 (v12.2.5). I haven't used Office vX since Tiger so I cannot comment on its stability with the latest update. But I suggest that if you haven't done so already, try opening Disk Utility and running Repair Disk Permissions on the 10.6.4 partition. Once this has completed I also suggest that you reset the printing system, restart your Mac and then add your printer queues again.
*How to Reset the Printing System*
1. Open System Preferences > Print & Fax
2. Move your mouse over the Printers list
3. Hold down the Control button and click the mouse (or right click if supported).
4. Click "Reset printing system ..."
5. Restart your Mac

Print Cancellati​on Problems

Similar Messages

Maybe you are looking for

Print Cancellation Problems