Problems coonecting a BESFR41 to an existing LAN

Here is the scenario.
Mobil application that is travelling from business to business providing a service.
The applications creators used the BESFR41 as the switch inside the application vehicle to communicate with the businesses it visits.
Before any suggestions are made, I cannot change anything in the application vehicle because it is not under my control and also the driver and the business owner of the application are clueless as to how the system is actually setup. The owner used a third party to assemble 5 of these vehicles.
I am currently unable to even detect the BESFR41 MAC on the network side and the application cannot aquire the network address from my LAN, yet if I take one of my laptops out to the application vehicle and plug in to the BESFR41, I can connect to my LAN??
So far I am the only business that the vehicle cannot communicate with so the owner is not compeled to work on this any further then it works or it doesn't.
Any ideas or suggestions?
Message Edited by SMH3778 on 03-18-2009 03:38 PM

If you are trying to connect the BEFSR41 router to another LAN you should know the Default IP Address of the DHCP Enabled Device on the existing LAN...
Once you have the information, you can connect the existing LAN to either the Ethernet Port of the WAN/Internet Port on the Linksys router...How would you like to configure it...

Similar Messages

Connecting 2950 to existing LAN

I recently purchased a WS-C2950T-24 to add to my existing network. I have mirrored the configuration of other 2950 switches in other offices (with exception of name and subnet info that differs between sites). The existing LAN in this office is comprised of 4 cisco WS-C2924-XL switches. I can connect to all 4 of the 2924 switches but not to the 2950. Any known issues of talking between the two different types of switches?

Its not a good practice to enable portfast on all the interfaces. It should be done only when the connection is terminated to an end host.
I think your problem is because of the trunk between the 2924XL and the 2950. The 2924 switch supports both dot1q and ISL trunk encapsulation whereas the 2950 supports only dot1q
try this
on the 2924XL port connecting to 2950
interface fa 0/24
switchport trunk encapsulation dot1q
switchport mode trunk
on the 2950 port conencting to 2924XL
interface fa 0/24
switchport mode trunk
HTH, rate if it does
Narayan

Problem in creating new versions for existing DIR using CV01N

I am working in SAP ERP 6.0 EHP 4.0 system.
I have problem in creating new versions for existing DIR using CV01N
I create a DIR version 00 with functional location and mpd cycles. Then when i try to create a new version by copying the contents created from already created document.I change the MPD cycles in the new version and save it.
once when i display the first document created the mpdcycle specified in version 01 is copied to the 00 version.
The document is inconsistent where versioning of document doesnot work properly wrt MPDCYCLE and MP HEADER.
The problem which i found was the document identification guid remains the same for all the document versions getting created.
The same is working fine in SAP ERP6.0 EHP3.0 sytem.
Please someone help me in resolving the above issue.
Regards,
Prasad.B

There is a change in the standard code.The reason for the above problem was because of a missing Enhancemnet point in a standard function module 'CV110_DOC_CREATE_WITH_TEMPLATE'.
IS-ADEC-MPD - Enhancement to copy MPD data
ENHANCEMENT-POINT CV110_DOC_CREATE_WTEMPL_01 SPOTS ES_SAPLCV110.
+*$*$-Start: CV110_DOC_CREATE_WTEMPL_01----------------------------------------------------------$*$*+
+**ENHANCEMENT 1 ZSF_AD_MPD_SAPLCV110.    "active version**+
+*** copy MPD relevant data from templ. doc to current doc**+
+**CALL FUNCTION 'MPD02_COPY_MPD_DATA'**+
    +**EXPORTING**+
      +**is_draw = ls_draw**+
    +**TABLES**+
      +**ct_drad = lt_drad.**+
+*ENDENHANCEMENT.**$*$-End:   CV110_DOC_CREATE_WTEMPL_01----------------------------------------------------------$*$*+
Created a custom enhancement point similar to SAP ECC6.0 EHP 3.0 system.
The reason was the buffer was not getting cleared previously.After inserting the above code the DIR's are getting created withot any issues.
Regards,
Prasad.B

Creating a LAN within an existing LAN using a spare router?

My other option is to use my phone as personal hotspot and use it's internet. Would that work?

Hello,I would like to set up a personal lab environment within an existing LAN that has router(s), switches, server, etc(basically the whole deal). That LAN operates on one IP subnet 192.168.100.0/24(I'm not sure, but I think DHCP for that subnet is running on the router which is the default gateway to the Internet.)
I have a spare router here. May I plug that router into the switch under my desk that connects to the 192.168.100.0/24 LAN and configure my spare router like so that it has its own LAN behind it such as 192.168.99.0/24 or 10.1.10.0/whatever, have that router think that the 192.168.100.0/24 subnet is actually the Internet access, and have a DHCP server running on my spare router that specifically servers my subnet only, not the outside 192.168.100.0/24 network. Then I will set up my own domain controller(s), file servers,...
This topic first appeared in the Spiceworks Community

Partial page load problem when using Muse in an existing non-Muse Masterpage; how to issue a jquery

Partial page load problem when using Muse in an existing non-Muse Masterpage; how to issue a jquery args.get_isPartialLoad().
My page is loaded into a palcehold within the Ajax update panel within the current Masterpage, so page loadload doesn't occur. But if my Muse page can capture the partial pageload then I can tell jquery to run the Muse formating routine.

Jackie, I am having the same issue and agree that it obscures our site analytics.
I only have the "WebMarketing" subscription - so I cannot see how often people visit my site (unless I just dont know how to view that). Here is a screen shot of how many different locations I have and how much it affects my site visitor count based on the other locations which seem "legit" because they have more page views than visits.
I hope there is a way to fix or block this.

Problem with Jabber and file transfers WAN - LAN-Users - a solution!

Hi,
I read a lot of messages about problems with file transfers between iChat-Users, if one (or both) are behind a NAT.
I had this problem to and found an easy solution:
My situation
iChat-Server behind a Netgear ProSafe FireWall. I opened the needed Ports including Port 7777 (the Port for the iChat-proxy (proxy65).
The iChat-Server is configured to host the domain "server.ourdomain.com" (as an example).
This address can be reached from the LAN and also from the WAN-side.
From the LAN-side the DNS redirects to 192.168.1.1, from the WAN this domain redirects to our official IP-address (the WAN-IP of the FireWall).
I tried nearly all kinds of mentioned solutions, but nothing helped.
The really easy solution is: I just added our official IP to the "Hosted Domains" in the iChat-section of Server-Admin.
After that change, the transfers are made via the proxy65 of iChat-Server. The transfers are shown in the log /private/var/jabberd/log/proxy65.log.
I think, that the other posters who also have this kind of problem are working in a similar setup (domain name of server is used from the LAN AND the WAN-side with different IP-addresses (LAN-IP & WAN-IP).
This solution will only work, if the WAN-IP is a fixed address.
svenc

Until the introduction of file promises in AIR Athena, it has never been possible to drag remote files out of an AIR application.
You could refer to the http://www.adobe.com/devnet/air/flex/articles/using_file_promises.html
Hope this is helpful. Please let me know if I could help more.

Weird problem w/AX as client on existing WiFi ...

So, I recently moved to a studio attached to a house that has a wireless network and have no problems seeing the network and getting on it to get online and such. I also have an AirportExpress which I used for a wireless network at my previous home and was connected via ethernet to the DSL modem. This is a basic set up. I was able to listen to music on my stereo through AirTunes, print, browse the internet, blah, blah, blah.
Now, I know my equipment is capable of becoming a client of an existing wireless network (COX cable highspeed) using the AirportExpress because I read it in the help topics. I did everything I'm supposed to and it works partially. The problem is after setting up the AX once I can no longer make any edits by selecting the "Configure" button because I get "error reading configration file ..." messages. I can get online but can't connect via Airport Admin Utility or iTunes. iTunes lists the speaker name but has the same problem hanging when trying to connect to the AX. The only thing I was able to do is just hard reset or factory reset the AX and set it up again but every time I did I got the same problem.
Please help.

So, I went ahead and messed with the Airport Express. It was sitting unplugged for about a month since the last attempt to getting it to work as a client of an existing WiFi network. You wouldn't believe it! Or maybe you would. It works now.
Here's the series of events: I plugged in the AX (my Mac was on and connected to the existing default "linksys" wifi), it started up and Mac saw the network. I opened Airport Admin, switched Airport to be connected to the AX and in Airport Admin I edited the settings for it to be a client of existing network (wasn't able to use encryption because both methods were'nt supported by the router). Left Mac alone and ate dinner, came back to Mac and saw that Airport was now connected to "linksys" but in Airport Admin it showed the AX, therefore, Airport was connecting to "linksys" via AX.
After many attempts prior, I never had that much success. Good sign. I thought maybe it was just getting online but AirTunes wouldn't work. Opened iTunes and had success with the Radio. Eureka!
All I have to say is, huh? But … it works now. That's all I care about.

Well its another 3rd gen. 8gb ipod touch problem. Apparently they don't exist and that really ticks me off because the apple packaging clearly stated it was an 8gb 3rd gen. and now i can't update it. Apple lied and now im paying for it.I better get a new1

A year or two back i dad just used up all of my money to buy a brand new ipod touch 3rd gen. 8gb. I bought it at a local sams club and i even still have the packaging that says it was an 8gb 3rd gen. But Apple lied to me because it is only an 2nd gen. I looked it up and they don't exist. Now i can't get any games or anything because of thier false advertisement and ripping us off (as you can't update from iOS 4.2.1). This also happened to many of my friends and other Apple customers throughout the U.S. It was an unopened product from Apple. Since they tricked us i hold Apple accountable. I demand a refund and anyone else in this delemma please share your story. APPLE OWES ME A REFUND.

I see that you have the same problem as guys in the sites I found.
http://apple.stackexchange.com/questions/54866
http://apple.stackexchange.com/questions/55334
http://apple.stackexchange.com/questions/55180
I think most of them manage to came out either with FULL REFUND, with 75-90% DISCOUNT for iPod 4G purchase, or FREE iPod touch 4G 8GB.
I'll tell you this, it's not Apple who lied to you, it's the misled DEALERS. I've been collecting evidences and it seems from the beginning (the time of press release) until the release of iPod 4G, Apple never stated that they intended to release iPod touch 3G in 8GB.
See this image of Apple online store back in early 2010 :
The 8GB model were only UPDATED with iOS 3 however the true NEW iPod touch at that time (Apple hadn't used the terms Generation yet) was available in larger capacity. The iPod touch 8GB wasn't RENEWED but rather RE-RELEASED with lower price as previous 8GB iPod touch were more expensive. If you still not convinced enough to believe it, well search the youtube and watch Phil Schiller's presentation in 09/2009. He shown 8GB model (he didn't say new) would only experience updated price of $199 but later on, he pushed the 8GB aside and explained the NEW larger capacity models would be granted double capacity and improved performance
Hence, I'm truthfully sorry to say that the one whom to be wronged isn't Apple but dealers themselves for false advertising. I suggest you to bring up your complain to the dealer with valid evidences because if you don't, I'm afradi you might lose your chance due to the time being.

Problems with a certain program for existing users

Hello,
We have problems with a third party software application. We have installed this software program on a terminal server (server 2003 32bit) and when we open this software with a existing user account the application crashes with the following entry in the
eventviewer:
Application Error 100
Faulting application ProTime.exe, version 4.1.0.9, faulting module msvbvm60.dll, version 6.0.97.82, fault address 0x000fd0d9.
For more information, see Help and Support Center at
http://go.microsoft.com/fwlink/events.asp.
We have checked the eventlog on the server but the only error that we see is the application error 100 when we open the program. Also we checked the rights on the program's database and folders but that doesn't help either.
The last thing we did was;
- Installing the software on a brand new virtual server with server 2003 x86 (no other software installed)
- Installing the software on a new virtual machine with server 2008 r2 x64 (no other software installed)
The strange thing is when we change something in the compatibility mode setting for example run as windows xp then we can run the program just fine but when the user logs off and log on again it doesn't work until you change something at the compatibility
mode setting (doesn't mather which setting)
When we create a new domain user then the software works properly without any settings changed.
Any idea what could cause this problem?
Thanks
With kind regards,
Lars

Hi Jesper,
Sorry for the late response. We think so, atleast the software company says it is.
We should not use the compat. mode because the application is not working on server 2003 x86, server 2003 x64, server 2008 r2.
It is just really strange. Software company has no clue how to fix this problem and they say it is caused by the active directory because when we add a new user then the application starts properly. User accounts created a long time ago are not able to start
the application.

Problems with creating SH Schema in exists Database 10.2.0.2

Hello ALL
I have problem with installation SH Demo Schema in exists Oracle Database 10.2.0.2 Enterprise Edition on Windows 2003 EE SP1
First I could try to configure my DB in Oracle Confuguration Assistant but I couldn't to add examles schemas there.
Then I installed Companion 10.2.0.1 with examples schemas in $ORACLE_HOME Database 10.2.0.2 and executed script sh_main.sql under SYS user.
After all SH Schema created in our DB but data exists in only two tables such as COSTS and SALES_TRANSACTIONS_EXT.
I haven't any more data in others tables.
In my log files I see follow :
SQL*Loader-500: Unable to open file (D:\oracle\DB_BI\demo\schema\sales_historydmsal_v3.ctl)
SQL*Loader-553: file not found
SQL*Loader-509: System error: The system cannot find the file specified.
SQL*Loader-500: Unable to open file (D:\oracle\DB_BI\demo\schema\sales_historydem_v3.ctl)
SQL*Loader-553: file not found
SQL*Loader-509: System error: The system cannot find the file specified.
SQL*Loader-500: Unable to open file (D:\oracle\DB_BI\demo\schema\sales_historysale_v3.ctl)
SQL*Loader-553: file not found
SQL*Loader-509: System error: The system cannot find the file specified.
and etc.
Please help me to install SH Schema in exists DB may be anybody resolved this issue.

The document you are refering to is OK, but it assumes you already have installed the demo files.
In order for the demo to be installed and working, some requirements must be met.
You must have installed DB10g Enterprise Edition, as demos such as SH require the partitioning option, available only on E.E.
Start a second installation from the companion disk, start your oracle installer, select Database Products, verify the Oracle Home details are the same as those of your Oracle Home, confirm the action and install.
At the end of the installation you must see these directories at the $ORACLE_HOME/demo/schema directory:
bus_intelligence mk_dir.sql.ouibak    mkunplug.sql   sales_history
human_resources   mk_dir.sql.ouibak.1 mkverify.sql   shipping
info_exchange     mkplug.sql           order_entry    sted_mkplug.sql.dbl
log               mksample.sql         product_media
mk_dir.sql        mksample.sql.sbs     README.txt

Problems sharing across two computers on home lan

I must be doing something basic wrong. The instructions for sharing a downloaded digital edtion sound very easy in the help manual but following those directions I am not able to share a book across two computers on my home lan.
Both computers have been authorized by my user id. When I open the menu item on Library menu/Authorize computer
I'm told the computer is authorized and my UID is shown. However when I attempt to `add' the book I get a message saying:
> This document cannot be opened on this machine.
> Please contact the site where you obtained the document
> to download another copy.
I just bought the book today not more than 2 hrs ago
The `knowledgbase' help for digital editions is completely useless and returns no hits regardless of what I type in the search field.
What else do I need to do to share a book across two home computers?

Harry
You shouldn't need anything else. The common problems (after you have gotten past the authorization) for sharing are:
- You copy over the .etd file instead of the .pdf file.
- You copy over the .pdf file from /Digital Editions/ebx_backup instead of /Digital Editions. (My best guess, given the error message).
- The file was purchased with only rights to view it on a single machine.
The not so common and more worrisome case would be if the License was not being correctly written into the file after you purchase it.
I would suggest that after verifying you are copying the correct file, you should open up a web support case, so that Bentley can track this, and help us gather all the correct information so we can figure out what is going on.
Sorry you're having problems
Jim Lester
Adobe Systems

Problem in Banking External reconcilation -already exist in Table "OMTH

Hi,
    All,
         I am getting One Problem while Banking External reconcilation for an accont.it is giving error that entry already exist in Table "OMTH".
         it happens many times,Can u tell me reason and what may be solution to not getting again this problem because it is coming many times .
Thanks In Advance

Hi
I found this Note 1062219 - Manual reconciliaton failed - primary key constraint
The note is for 2005, but I would run the queries related in the note.
Kind regards.
Agustí

Problem in using BAPI_TRLSRVAPS_SAVEMULTI to create transportation lanes

Hi,
While using BAPI_TRLSRVAPS_SAVEMULTI to create transportation lanes,bapi returns errors
1.Product transportation lane not found in database or in the tables and
2.Product <matnr> ( coming from the flat file in the program ) cannot be both product-independent and product-specific.
Please suggest solution to the problem.

Try to user APO Loader Excel and fill the data you are filling for BAPI "BAPI_TRLSRVAPS_SAVEMULTI" and see whether it works or not ?
Alternately you can fetch the data from APO to Excel using the get option of the "APO Loader Excel"
Please reward points if this helps to you.

Problem verifying if a given URL exists

Hi,
I have migrated from Java 1.2.2 to 1.3 (Windows NT version), and a big problem has arosen.
I used to verify if a given URL existed with this piece of code:
try {
URL url = new URL(path);
url.openStream();
} catch (Exceptions ....) {}
But right now, I get sometimes a "FileNotFoundException" when the file DOES EXIST.
Is this possible? It only occurs sometimes. Why?
I also tried this, but this piece of code never throws an exception:
URLConnection conn = url.openConnection();
conn.connect();
Thanks.

I had the same problem and solved it with this:
public boolean exists(URL url) {
try {
    HttpURLConnection con = (HttpURLConnection)url.openConnection();
    con.connect();
    int responseCode = con.getResponseCode();
    con.disconnect();
    return responseCode == HttpURLConnection.HTTP_NOT_FOUND;
catch (IOException e) {
    e.printStackTrace();
    return false;
}The code comes from these threads:
http://forum.java.sun.com/thread.jsp?forum=31&thread=206582
http://forum.java.sun.com/thread.jsp?forum=31&thread=249739

Problem while reconfiguring OIM 11g with existing Database

Hello,
I had some issues with my OIM 11g instance, so i reconfigured it by deleting user_projects folder,before deleting i took backup of config folder as i wanted to
configure with existing database.
Following steps were performed for reconfiguring OIM11g:-
1)Ran config.sh from <Middleware>/Oracle_IDM1/common/bin
2) Copied .xldatabasekey file to newly created domain
3)Ran config.sh from <Middleware>/Oracle_IDM1/bin
Then tried to start AdminServer, it showed status as running but with errors like
java.lang.NoClassDefFoundError: Could not initialize class oracle.dfw.impl.common.TempFileManager
at oracle.dfw.spi.portable.PortableDiagnosticsFrameworkProvider.init(PortableDiagnosticsFrameworkProvider.java:120)
Then tried to start OIM server , it showed status as running but with error as
oracle.iam.platform.utils.OIMAppInitializationException:
OIM application intialization failed because of the following reasons:
Password for .xldatabasekey is not seeded in CSF.
Then i tried to cofigure domain again & this time i didnt select Oracle Identity Manager from Select domain source & checked AdminServer & it was running without any errors, but when i select Oracle Identity Manager from Select domain source then i get above problems.
Can anyone provide pointers about how to resolve this issue .
Thank-You
Rahul Shah

Dear Rahul,
I got the same errors:
./admin/IDMDomain/mserver/IDMDomain/servers/wls_oim1/logs/wls_oim1.log
####<Jan 27, 2013 10:58:09 PM CET> <Error> <Deployer> <server02> <wls_oim1> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <aa66ef4907f1903f:4c6a3b0:13c7e03232f:-8000-0000000000000003> <1359323889050> <BEA-149205> <Failed to initialize the application 'oim [Version=11.1.1.3.0]' due to error oracle.iam.platform.utils.OIMAppInitializationException:
OIM application intialization failed because of the following reasons:
oim-config.xml was not found in MDS Repository.
oracle.iam.platform.utils.OIMAppInitializationException:
OIM application intialization failed because of the following reasons:
oim-config.xml was not found in MDS Repository.could you explain, how did you sort out it, please? For example point 2 did you create one more domain?
Best regards,
Lain

Problems coonecting a BESFR41 to an existing LAN

Similar Messages

Maybe you are looking for