Replaced my ink, getting error 0xc18a0206

I replaced the ink with new HO cartridges. Ink level reads full. Otherwise all I get is the error. I hsvr reset the machine and cleaned all the contacts with distilled water and a Q-tip.
Please tell me how to correct this problem.
Machine: Photosmart C7280
OS Windows 8.1
please be aware that after spending $55.00 on an all new HP-02 ink set to get an error message and not even a test page, I am about ready to buy a Canon....

Hi,
Please try the following steps:
Without turning off the product,
Remove the cartridges from the product.
Wait until a message to insert the cartridges displays. If you do not see a message within a few minutes, skip to the next step.
NOTE:If your printer does not have a display, wait until the cartridge lights blink. If the cartridge lights do not blink within a few minutes, skip to the next step.
Disconnect the power cord from the back of the product.
Wait 60 seconds.
Reconnect the power cord. If the product does not automatically turn on, press the Power button ( ).
Reinsert the cartridges, and then close any open doors on the product.
If you receive a prompt to print a calibration page, do so.
Try printing again.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

Trying to sync selected (greyed out) contacts to my replacement 4s. Get error messages - computer not setup to sync - override or OK. OK - session could not start. How do I fix?

I have a new replacement 4s. I am trying to set it up. I hate iCloud but need it to sync my calendar to my phone. I mistakenly set it up to sync Contacts too and found out it synced ALL contacts which I do NOT want. I used to use iTunes to sync only selected contact folders (one I call Sync). Others are too sensitive to have on my phone. So I turned off "where is my iPhone", and turned off "Contacts" on iCloud. It said it would delete all my contacts on my phone the next time I sync (using iTunes). So I try to sync my Contacts using iTunes and find that under "Info" on the device tabs my only possible selection is ALL contacts with the "Selected" button greyed out. But even leaving all checked, I get the message "iTunes cannot sync information with the iPhone because syncing has been disabled on this computer (my Mac). Do you want to enable syncing?" I hit the button "Enable syncing" and I get the error message "Syncing cannot be enabled on this computer" with "Override" and "OK" my choices. If I select "OK" I get the error message "iTunes could not sync information to the iPhone (Name) because a sync session could not be started". I can sync my music and my apps but get this stupid message otherwise. What gives and I do I fix this? Thanks

Actually I can't sync anything - no music, photos, etc. And it tries to start syncing as soon as I plug in my iphone and itunes is open. It ends "sync" but hasn't done anything. I have tried deleting lockdown files (per "solution" found here). I have deleted all my backups (per other "solutions"). I have restored my iphone 2x. I have done soft boots of my iphone. My macbookpro 10.9.3. iphone 7.1.1. iTunes 11.2.2 (3).

Replace library folders getting error

When I try to replace a folder in my library by a new version of this folder, the complier show these warning:
**Warning** The linkage identifier 'com.aconma.controls.TextMenu' was already assigned to the symbol 'AconmaComponents/NumericStepper/AconmaComponents/TextMenu/textMenu', and cannot be assigned to the symbol 'AconmaComponents/TextMenu/textMenu', since linkage identifiers must be unique.
**Warning** The linkage identifier 'com.aconma.controls.Slider' was already assigned to the symbol 'AconmaComponents/NumericStepper/AconmaComponents/Slider/Slider', and cannot be assigned to the symbol 'AconmaComponents/Slider/Slider', since linkage identifiers must be unique.
**Warning** The linkage identifier 'com.aconma.controls.NumericStepper' was already assigned to the symbol 'AconmaComponents/NumericStepper/AconmaComponents/NumericStepper/NumericStepper', and cannot be assigned to the symbol 'AconmaComponents/NumericStepper/NumericStepper', since linkage identifiers must be unique.
**Warning** The linkage identifier 'com.aconma.controls.ComboBoxItem' was already assigned to the symbol 'AconmaComponents/NumericStepper/AconmaComponents/ComboBox/ComboBoxItem/ComboBoxItem', and cannot be assigned to the symbol 'AconmaComponents/ComboBox/ComboBoxItem/ComboBoxItem', since linkage identifiers must be unique.
**Warning** The linkage identifier 'com.aconma.controls.ComboBox' was already assigned to the symbol 'AconmaComponents/NumericStepper/AconmaComponents/ComboBox/ComboBox', and cannot be assigned to the symbol 'AconmaComponents/ComboBox/ComboBox', since linkage identifiers must be unique.
**Warning** The linkage identifier 'com.aconma.controls.TickBox' was already assigned to the symbol 'AconmaComponents/NumericStepper/AconmaComponents/CheckBox/TickBox/TickBox', and cannot be assigned to the symbol 'AconmaComponents/CheckBox/TickBox/TickBox', since linkage identifiers must be unique.
**Warning** The linkage identifier 'com.aconma.controls.CheckBox' was already assigned to the symbol 'AconmaComponents/NumericStepper/AconmaComponents/CheckBox/CheckBox', and cannot be assigned to the symbol 'AconmaComponents/CheckBox/CheckBox', since linkage identifiers must be unique.
I have to delete old folder and paste the new, and everything work fine
Anyone have the same issue?

As for classes, the problem is probably that you're duplicating a component of some sort to try to change the behavior or appearance and Flash is warning you that you pasted a duplicate. Breaking apart the error:
**Warning**
The linkage identifier
'com.aconma.controls.TextMenu'
was already assigned to the symbol
'AconmaComponents/NumericStepper/AconmaComponents/TextMenu/textMenu',
and cannot be assigned to the symbol
'AconmaComponents/TextMenu/textMenu',
since linkage identifiers must be unique.
Sometimes it just helps to break it out.
If you go in the folder "AconmaComponents/NumericStepper/AconmaComponents/TextMenu" and find the library item named "textMenu", right-click on it, select properties and look in Advanced (select the "Advanced" rolldown if it's not already open). You should see "Export for Actionscript" checked off. You should also see in the "Class" input below the class: com.aconma.controls.TextMenu
Now if you do the same steps but this time to the library element in the folder "AconmaComponents/TextMenu/"
library item "textMenu", you should see the same class name: com.aconma.controls.TextMenu
That's bad. Each linkage ID is based on the class name, and they must all be unique.
You have to remove the duplicate (either of the 2 folders mentioned) to remove that one warning. You'll need to continue deleting the other repeated elements to get rid of the rest of the warnings. Once you have no warnings left it should work. However any references in your project to what you just deleted won't show up.
If you want to customize that specific component multiple times it should follow the standard component skinning model but you'll need to refer to their documentation to verify that. You'll need to only include the TextMenu component (and all the others) a single time in your project and then assign different skins to change anything about them.

I keep getting a "Print Cartridge Error" even after replacing both ink carts in my psc2410

I keep getting a "Print Cartridge Error" on my psc 2410. I replaced both ink cartiridges and cannot clear the error. Any ideas?

After playing with it, I now get only a 'check color cartirdge' message. I've pulled it out, checked the contacts and put it back in several times to no avail...

Error 'INK CARTRIDGE ERROR REPLACE CARTRIDGE' on EPSON Stylus Pro 9700

I have removed the printhead and clean it with a cleaning solution. I have already done it 2 or 3 times before and had no issues but this time I am getting this error message 'INK CARTRIDGE ERROR REPLACE CARTRIDGE' with all the cartridges flashing on the front panel. If I remove any one cartridge and turn the printer on it recognize all the other cartridges apart from the one I have removed and ask me to installed the missing cartridge. After installing the missing cartridge I get the same error again.
Any help will be much appreciated.
This topic first appeared in the Spiceworks Community

Update or reinstall the EPSON software.

Everytime I change ink cartridges, I get error message stating "REFER TO PRINTER DOCUMENTATION"

EVERYTIME I CHANGE INK CARTRIDGES, I GET AN ERROR MESSAGE STATING REFER TO PRINTER DOCUMENTATION. I HAVE UNPLUGGED AND TURNED EVERYTHING OFF AND TRIED SEVERAL TIMES.

Hello enicole87,
Welcome to the HP Forums.
I see that you are having some issues when replacing the ink cartridges with an error message.
So I can better assist you, please respond with your printers Model Number.
How Do I Find My Model Number?
Write be back when you have time and I will be happy to help.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

I have problems with my printer says the ink system failure error 0xc18a0206 what do I have new cart

I have problems with my printer says the ink system failure error 0xc18a0206 what do I have new cart. Printer is Hp Photosmart c5180

This article should help resolve the error you are getting:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03081973&cc=us&dlc=en&lc=en
Give the steps a try and let us know if it helps.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

After soak test update, I get error messages repeatedly. The majority are "unfortunately, messaging has stopped", but you can replace messaging with "android os", or any other process, as it happens with more than just messaging. I have had numerous peopl

After soak test update, I get error messages repeatedly. The majority are "unfortunately, messaging has stopped", but you can replace messaging with "android os", or any other process, as it happens with more than just messaging. I have had numerous people call and ask why I didn't reply to their texts...and I look, but have not received any new texts. YES, I have restarted phone. I have cleared data as well as cache on all apps. I have downloaded the vzw messaging app, which seems silly, since it happens with several different processes and apps, but all to no avail. I am missing texts from my employer, from my family. This did happen, but rarely, before this "soak test". It is now Kitkat version 19.6.3.obake_verizon.en.US. THIS is when I started having problems...like 50 times a day kind of problems! I have seen hundreds of posts all over the internet over the past 3 days. Does no one know how to fix this??? Shouldn't there be a way to revert phone to a pre-update state? and no, hard reset did NOT work!!!! I have been with verizon for well over 15 years, but I have not upgraded my lines and will not in July either. This is ridiculous. It's not like my games aren't working, it is my messaging and "android os"...my lifeline at work!

kristinaf333,
Oh no, I am sorry to hear your messages are not working since the software update. I greatlly appreciate doing all that troubleshooting to try and get the messaging application back in business. I know how much I rely on my messages so I can understand the urgency to get this resolved. Have you had a resolution ticket opened since you started experiencing issues with your messages? Does this happen with all contacts or just some? Please provide additional information to ensure we get to the bottom of this for you.
KarenC_VZW
Follow us on Twitter @VZWSupport

My iPad2 Apple logo (the blue box with a capital A) was deleted in error. I would like to know how to replace it or get it back. Thanks so much . . .

My iPad2 Apple logo (the blue box with a capital A) was deleted in error. I would like to know how to replace it or get it back. Thanks so much . . .

Do you mean the App Store app on your iPad ? If you do then it can't be deleted, but you might have hidden it via Settings > General > Restrictions > Installing Apps 'off' - if that is 'off' then turn it back 'on' and the app should show on one of your iPad's home screens again

I am trying to re-install Creative Suite 5.5 Design Standard on my Widows 7 Professional computer after I had to replace the hard drive. I keep getting error message and I get "Exit Code 15: Media DB Sync failed". I have run C Cleaner with same results. H

I am trying to re-install Creative Suite 5.5 Design Standard on my Widows 7 Professional computer after I had to replace the hard drive. I keep getting error message and I get "Exit Code 15: Media DB Sync failed". I have run C Cleaner with same results. Have Disabled UAC and Startup items and Services with no success. Please help - frustrated to no end. Can someone help me?

make sure you're using the adobe cleaner, not crap cleaner, Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6
copy the installation files to a desktop folder and install from there.

Hi, I have a HP f380 all in one printer. I have installed new black ink cartridge and get error.

Hi, I have a HP f380 all in one printer. I have installed new black ink cartridge and get error stating please insert black ink cartridge.
Please Help

Make sure it is a genuine HP cartridge. Take it out and clean the contact on the cartridge and in the printer. Try again.
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

Getting errors in replacing already packaged file

Hi Jim,
I am getting errors while replacing already packaged file. I have changed action as replace and already passed resource id into the package xml but it is saying that duplicate src.
Please help me in this case.
Best,
Mangal

This solved a problem I have been working on for days.....
Where is this kind of gems documented?
Am I missing some resources?
Best
Jon H.

When restored replacement phone I get an error come up saying error (-50)

when I restored my replacement phone I get a message restore error (-50) can anybody help

Try Recovery Mode.

TS1538 hi i updated my iphone 4 with itunes and now i cannot use my phone as i keep getting error 16 after trying to restore my phone....i cannot afford to replace ..can any body help me...the phone is out of warrenty so apple do not want to know....pleas

hi i updated my iphone 4 with itunes and now i cannot use my phone as i keep getting error 16 after trying to restore my phone....i cannot afford to replace ..can any body help me...the phone is out of warrenty so apple do not want to know....please any help

https://discussions.apple.com/message/23100453#23100453
more hits from the search
https://www.google.dk/search?q=restore+itphone+error+16&oq=restore+itphone+error +16&aqs=chrome..69i57j0l5.11485j0j7&sourceid=chrome&espv=210&es_sm=93&ie=UTF-8

Im getting errors when i do a mem test on my hp a6000f.....ive replaced the ram and still get errors

im getting errors on mem test, Ive replaced the ram, still get errors. How do I disable the L2 cache....on hp a6000f, I dont see anywhere to do it while im in the BIOS/ CMOS setup
I get error code : BIOME-1

Here is what you should do to trouble shoot your problem.
Open up the composition that is giving you problems
Your error message tells you that you are having problems with the Shatter effect so select the layer with the shatter effect and turn the effect off
Try a ram preview
If the ram preview is successful add a solid to your comp
Copy your shatter effect and paste it to the new solid you created
Turn off all other layers
Try a ram preview
If the ram preview crashes go back to step 6 and reset shatter and try again
If the ram preview is successful start adding the properties from your original shatter effect until you get a crash.
If the ram preview works the first time you try step 6 then there is something wrong with the combination of shatter and the original layer it was applied to so remove shatter from that layer, pre-compose that layer moving all attributes to the new layer then paste the working shatter from the solid to the pre-comp, turn off the solid and try another ram preview.
Do you kind of get the procedure here. When something is causing a crash first isolate that problem, try it on something simple, then try different things until you can reproduce the crash. Make sure you are saving copies of your project so you can easily go back.
If you can't figure out what settings in Shatter are causing the crash then we need to know everything there is to know about your composition and see a screenshot or the project file. If it is the footage that is causing the crash then you need to transcode, recompress, or in some other way change the format of the footage. There is nothing we can surmise from the details you have given us that give us any clue why shatter is crashing. It usually does not. I can't think of the last time it caused a crash for me. The only possible thing I can think of that would be causing a crash is that the number of particles is causing your system to run out of memory.

Replaced my ink, getting error 0xc18a0206

Similar Messages

Maybe you are looking for