Sample configuration

Hello,
I'm wondering if someone can point me to an updated Sample Configuration doc to set up the following :
Cisco 1121 ACS ver. 5.3 as Radius server
Cisco 2500 WLC serving Light AP's
Windows 2008R2 Active Directory as backend authentication server
Basically my client wants to use an AD security group to allow access to thier Wireless AP's for their user community
I "think" I have most of the pieces in place. Just a little fuzzy on the full picture. Also, to complete this config, will I need any certificates? What protocols (client) are best to use, etc?
Thank you

Hello,
I think the link below might help you out:-
https://supportforums.cisco.com/docs/DOC-21679

Similar Messages

Need a sample configuration

Folks,
I wrote a small program to parse the configuration. I am looking for a sample configuration of a Edge Router ( preferably 7200 ) having lots of configuration data including VPN , Martini Tunnel etc. I need to test my parser.
Any help will be greatly appriciated.

And....I am looking for a sample program to parse...could you help me...

Linksys WRP400 - VoIP Sample configuration guide for VoiceMeUp

Thanks to Linksys for that fine device. Few installations so far with this device and it has prooven his stability and reliability.
Note: Good T38 support and excellent QoS.
Here is a sample of configuration to VoiceMeUp
Linksys WRP400 - Sample configuration guide
[english] - [français]
Enjoy!
For more informations about VoiceMeUp VoIP services, please visit us at voicemeup.com
Message Edited by NothinElse on 08-25-2008 01:09 PM

Clearly this is too late to help you, but since this is showing up on Google and there are about a thousand views, this answer might be helpful to another.
Once you access the Voice Admin menu and provision your device for your VoIP provider, access to the Voice menu is subsequently "Locked".
Your VoiP provider's system has set a new unique password for the Voice menu once the provisioned device has synced with your providers system.
You should be able to get that password from the control panel on you VoIP account profile under "equipment" or a call to support or an e-mail request should garner the password.
The Login will be "admin" and the password provided will get you back into Voice menu system.
You will also need this password if you want to reset the Voice features back to factory defaults. Because of this system it appears that a WRP400 cannot be unlocked by merely using the reset button.

Remote access sample configuration

Hi,
i have a 3825 router with a NM-12DM (digital modem), and i want to configure remote access on it.
Can some body give me a link for a sample configuration ?
Regards

Howdy,
The following link has a great simple config that should enable you to get started:
http://www.cisco.com/en/US/customer/products/hw/routers/ps274/products_configuration_example09186a0080094691.shtml
Hope that helps.
Pls remember to rate posts.
Regards,
Paresh.

Sample configuration to simulate PSTN

Hi,
I have couple of 3725 routers with FXO & FXS modules.
Looking for sample configuration to simulate PSTN cloud.
Regards
Meer

This URL might be help you.
http://www.cisco.com/en/US/tech/tk652/tk701/technologies_configuration_example09186a008022eaa3.shtml

Sample Configuration For Ethernet over MPLS.

I am looking for a sample configuration and scenario for the Ethernet over MPLS.I would appreciate if I get some explaination with it.How the LDP is configured for the directed sessions (as per Martini draft) and the auto discovery (as per kompella draft) with respect to Ethernet over MPLS.Cam anyone help me in this ?

Here's a sample EoMPLS configuration on the PE routers:
R1:
interface Loopback0
ip address 1.1.1.1 255.255.255.255
interface Ethernet0/0.10
encapsulation dot1Q 10
! 10 = vcid must match the vcid configured on the other side
mpls l2transport route 2.2.2.2 10
R2:
interface Loopback0
ip address 2.2.2.2 255.255.255.255
interface Ethernet0/0.10
encapsulation dot1Q 10
mpls l2transport route 1.1.1.1 10
The LDP directed session will be setup automatically by the router when the xconnect statement is configured.
Cisco IOS doesn't support the Kompella Draft.
For more information, see the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122t/122t15/atomt/ftatomtb.htm
Hope this helps,

QoS Sample configuration: Catalyst 6500-E

Dear Experts,
I'm looking for sample configuration documents for configuring QoS on Sup2T with IOS 15.1 SY.
Cuold you point me to appropriate documents please.
S

Port is configurable with QoS service policy.
Unable to configure VLAN with QoS service policy.
6506E-2T#
interface Vlan112
ip address 10.112.112.1 255.255.255.0
end
6506E-2T(config)#int vlan 112
6506E-2T(config-if)#service-policy type lan-queuing input INGRESS-1P7Q2T
HQM not supported interface Vlan112MQC features are not supported for this interface
Anyone come accross this please?
platform qos vlan-based is not available in config listing.
(config)#platform qos ?
10g-only           qos pure 10G mode
aggregate-policer Named aggregate policer
marking            marking keyword
police             police keyword
protocol           protocol keyword
queueing-only      queueing-only (no QoS rewrite, no policing)
rewrite            packet qos rewrite enable/disable
service-policy     global policy map name
statistics-export qos statistics data export
Testing on 6506-E, Sup2T, IOS15.1SY.
SS

[svn:bz-trunk] 10057: Update the sample configuration to include a comment to warn people not to use debug level logging in production .

Revision: 10057
Author:   [email protected]
Date:     2009-09-08 10:58:36 -0700 (Tue, 08 Sep 2009)
Log Message:
Update the sample configuration to include a comment to warn people not to use debug level logging in production.
Modified Paths:
    blazeds/trunk/resources/config/services-config.xml

Remember that Arch Arm is a different distribution, but we try to bend the rules and provide limited support for them. This may or may not be unique to Arch Arm, so you might try asking on their forums as well.

Sample configuration of using (MSTP) feature on 3560

Hi,
I have 3560 switch running PVST, performing purely as layer 2 vlans, I already reached 120 vlans so I will be running out of spantree soon.
I would like to have a sample configuration of using (MST) feature to map multiple vlans to a single vlan to minimize my maximum spantree per vlan usage.
Any sample config would be highly appreciated.
thanks,

Hi Friend,
Have a look at this
Switch(config)# spanning-tree mst configuration
Switch(config-mst)# instance 1 vlan 10-20
Switch(config-mst)# name region1
Switch(config-mst)# revision 1
But I will recommend you to go through the complete link below to get full idea of MST before implementing in your network.
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat3560/12225see/scg/swmstp.htm#wp1017196
HTH,if yes please rate the post
Ankur

Sample Configuration vor PRI (E1) and MICA Modem

Where can I find a Sample Configuration
for a Cisco 3640 with PRI (E1) and a
MICA Modem Card. (Has to work with Dialer Interface)
(I just found a Configuration for PRI (T1) and MICA Modem)

The configuratioj for a T1 or E1 is almost the same, except for E1 parameters:
controller E1 0
framing crc4
linecode hdb3
clock source line primary
pri-group timeslots 1-31
controller E1 1
framing crc4
linecode hdb3
clock source line secondary
pri-group timeslots 1-31
interface serial0:15
isdn incoming-voice modem
dialer rotary-group 1
interface serial1:15
isdn incoming-voice modem
dialer rotary-group 1
interface loopback0
ip address 172.16.254.254 255.255.255.0
interface ethernet0
ip address 172.16.1.1 255.255.255.0
!The following block of commands configures DDR for all the ISDN PRI interfaces
!configured above. The dialer-group and dialer rotary-group commands tie the
!interface configuration blocks to the DDR configuration.
interface dialer1
ip unnumbered loopback0
encapsulation ppp
peer default ip address pool default
ip local pool default 172.16.254.1 172.16.254.60
dialer in-band
dialer-group 1
dialer idle-timeout 3600
ppp multilink
ppp authentication chap pap default

Please gives sample configure VPN site to site on ASA 5512-x v.9.1!

Dear All,
Could you gave sample configer ASA 5512-x v.9.1 for VPN site to Site, i use to configure on ASA 5510 V.8.2 but on ver 9.1 i never configure.
my is use that i dont know to how to configure nonat.
i saw some configration as in the attach file they just to show configure VPN but we did not see nonot on command.
http://www.cisco.com/en/US/docs/security/asa/asa91/configuration/vpn/vpn_site2site.html
Best Regards,
HK

Hi,
The new configuration format for NAT0 / NAT Exemption / Identity NAT is the following
object network SOURCE-NETWORK
subnet
object network DESTINATION-NETWORK
subnet
nat (inside,outside) source static SOURCE-NETWORK SOURCE-NETWORK destination static DESTINATION-NETWORK DESTINATION-NETWORK
In the above
SOURCE-NETWORK contains the network on your side of the network
DESTINATION-NETWORK contains the network on the remote side of the L2L VPN
The NAT configuration presumes that you are using interfaces with the name of "inside" and "outside"
The reason you see 2 of each "object" in the NAT configuration is that there is no NAT performed for them. You would have option to do NAT for both source and destination but in this case we dont want that.
Depending how many source and destination networks we are talking about, this might need some modifying.
Hopefully this helps
- Jouni

Sample configuration needed for MessageIDExtractor Axis handler

Hi there,
I am trying to configure the MessageIDExtractor Axis handler (java:com.sap.aii.axis.soap.MessageIDExtractor) in a SOAP Sender CC. However, the sample provided in de Axis FAQ is not enough to complete the configuration.
I want to take the value of a SOAP Header element in the payload, and reuse that as PI Message ID.
The path to the ID will be somthing like; "anamespace:A_SOAP_Header/AId"
Many thanks,
Roberto

>
yzanagi wrote:
> ....
> The instruction in the FAQ note is actually straightforward if you are familiar with the xpath notation.
>
> If it's not working, can you provide how you set these parameters and how your SOAP envelope exactly looks?
>
+
# Can I extract some ID value from the SOAP envelope and use it as the message ID?+
You can use the com.sap.aii.axis.soap.MessageIDExtrator handler to extract some ID value from the SOAP envelope and use it as the message ID. This handler can extract an ID string value (i.e., the 36-character GUID string) from the SOAP envelope and set it to the request or response message ID property in the message context. The ID string must be contained within some XML element. See a configuration for extracting the ID from WS-Addressing's MessageID element. {quote)
Hi,
Thanks for your reply;
I'm familiar with xpath however the FAQ does not mention the use of xpath anywhere. Please see above an extract of the FAQ regarding the MessageIDExtractor;
The provided example of the module configuration looks like this:
Module Key | Parameter Name | Parameter Value
id | handler.type | java.com.sap.aii.axis.soap.MessageIDExtractor
xireq | handler.type | java.com.sap.aii.axis.xi.XI30InboundHandler
sap | module.pivot | true
xires | handler.type | java.com.sap.aii.axis.xi.XI30InboundHandler
When you observe this configuration you notice that there's only one entry for the MessageIDExtractor. How will the handler know which XML field to pick from the incoming SOAP envelope? I think the example is missing some additional parameters where you can provide the xpath query.
Can you clarify?
Many thanks,
Roberto
Edited by: Roberto Viana on Nov 5, 2010 9:00 AM
Edited by: Roberto Viana on Nov 5, 2010 9:06 AM

ACE 4710 Application Acceleration Optimization Sample Configuration

Is the sample acceleration/optimization configuration sample in the Cisco 4700 Series Application Control Engine Appliance Application Acceleration and Optimization Configuration Guide Software Version A3(1.0)August 2008 (starting on page 1-7 of document) a valid/recommended configuration sample for acceleration/optimization, or do other Cisco validated design guides exist for the 4710 (acceleration/optimization)?

A great resource is the Solution Reference Network Design guides. Here's a link to the Application Engine design guides.
http://www.cisco.com/en/US/partner/netsol/ns751/networking_solutions_sub_program_home.html
Hope it helps.

Link of Sample Configuration of APs in Design Zone

Hi,
I'm trying to find a document in Design Zone about configuring a Wireless AP and I wasn't able to find it. Can someone provide a link?
I have a good experience configuring switches, routers and firewalls in CLI and this is the first that I have my hands on APs (1240 AG).
Thanks in advance.

Hi
Here is the link where you can check on the configuration guide for the access point you have.
http://www.cisco.com/en/US/partner/products/ps6521/prod_configuration_examples_list.html
http://www.cisco.com/en/US/partner/docs/wireless/access_point/12.4_10b_JA/configuration/guide/scg12410b.html
If you let me know what you want to achieve with the AP, I could try to provide you to steps to configure the AP as needed.
As basic information remember that the access points are layer 2 devices . To be able to configure the unit you need that the unit gets an IP address from the DHCP server on the network and you access the AP via the GUI or CLI using the IP address the DHCP server gave it or if not you can also configure an static IP address on the unit using the console port and assign the required IP address to the BVI1 interface.

Need Sample Configuration in ACS 4.2

I need configuration of ACS 4.2 for logging domain users into Network Devices.

What is the current status of your deployment? Have you already integrated ACS 4.2 with AD/domain? If yes, are you able to fetch the active directory groups in group mapping section.
If you still need to integrate ACS with AD, please broswe the below listed post and download the word document to review.
https://supportforums.cisco.com/message/4076705#4076705
Once done, try and login to your network devices via domain username and password. In case it doesn't work, please go to reports and activities > failed attempts.
Let us know how it goes.
~BR
Jatin Katyal
**Do rate helpful posts**

Sample configuration

Similar Messages

Maybe you are looking for