SAP on Ubuntu Correct settings for etc/hosts?

Hi,
I installed the SAP test drive version on Ubuntu (VirtualBox). After starting the SAP GUI (
/home/minisap/SAPClients/SAPGUI7.20rev5/bin/guistart /H/ubuntu64/S/3242
) I get the following error:
Error: partner 'ubuntu64:3242' not reached
Sun Feb 5 14:07:26 2012
Release 720
Component NI (network interface), version 40
rc = -10, module nixxi.cpp, line 3286
Detail NiPConnect2: 127.0.0.1:3242
System Call connect
Error No 111
'Connection refused'
I guess that the settings of the file etc/hosts are not correct. After the installation of ubuntu the file contains
10.0.2.15    ubuntu64    # Added by NetworkManager
127.0.0.1    localhost.localdomain    localhost
::1    ubuntu64    localhost6.localdomain6    localhost6
127.0.1.1    ubuntu64
# The following lines are desirable for IPv6 capable hosts
::1     localhost ip6-localhost ip6-loopback
fe00::0 ip6-localnet
ff00::0 ip6-mcastprefix
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters
ff02::3 ip6-allhosts
According to the test drive readme file I have to ensure that etc/hosts contain at least the following lines:
127.0.0.1      localhost
n.n.n.n      <HOSTNAME>.<DOMAINNAME>      <HOSTNAME>
n.n.n.n      nplhost
where "n.n.n.n" is a valid IP-adress.
I tried different settings but the above mentioned error still occurs... Does anyone know the correct settings of etc/hosts or know what the problem could be?
Thanks and regards

OK, I logged on as user nnpladm and typed
startsap nplhost
ps -ef|grep sap
ps -ef|grep sap
sdb       3424     1 0 16:15 pts/1    00:00:00 /sapdb/NPL/db/pgm/vserver -sdbstarter 1002 1003 A -S 7200 -Y
sdb       3425 3424 0 16:15 pts/1    00:00:00 /sapdb/NPL/db/pgm/vserver -sdbstarter 1002 1003 A -S 7200 -Y
sdb       3428     1 0 16:15 pts/1    00:00:00 /sapdb/programs/pgm/niserver
sdb       3448     1 0 16:15 ?        00:00:00 /sapdb/NPL/db/pgm/kernel NPL -diagpipe 16
sdb       3451 3448 0 16:15 ?        00:00:02 /sapdb/NPL/db/pgm/kernel NPL -diagpipe 16
npladm    4903     1 0 16:16 ?        00:00:00 /usr/sap/NPL/SCS00/exe/sapstartsrv pf=/usr/sap/NPL/SYS/profile/START_SCS00_nplhost -D
npladm    5187     1 0 16:16 ?        00:00:00 sapstart pf=/usr/sap/NPL/SYS/profile/START_SCS00_nplhost
npladm    5209 5187 0 16:16 ?        00:00:00 ms.sapNPL_SCS00 pf=/usr/sap/NPL/SYS/profile/NPL_SCS00_nplhost
npladm    5210 5187 0 16:16 ?        00:00:00 en.sapNPL_SCS00 pf=/usr/sap/NPL/SYS/profile/NPL_SCS00_nplhost
npladm    6414     1 0 16:16 ?        00:00:00 /usr/sap/NPL/DVEBMGS42/exe/sapstartsrv pf=/usr/sap/NPL/SYS/profile/START_DVEBMGS42_nplhost -D
npladm    6700     1 0 16:17 ?        00:00:00 sapstart pf=/usr/sap/NPL/SYS/profile/START_DVEBMGS42_nplhost
npladm    6740 6700 0 16:17 ?        00:00:00 ms.sapNPL_DVEBMGS42 pf=/usr/sap/NPL/SYS/profile/NPL_DVEBMGS42_nplhost
npladm    6742 6700 0 16:17 ?        00:00:00 ig.sapNPL_DVEBMGS42 -mode=profile pf=/usr/sap/NPL/SYS/profile/NPL_DVEBMGS42_nplhost
npladm    6755 6742 0 16:17 ?        00:00:00 /usr/sap/NPL/DVEBMGS42/exe/igsmux_mt -mode=profile -restartcount=0 -wdpid=6742 pf=/usr/sap/NPL/SYS/profile/NPL_DVEBMGS42_nplhost
npladm    6756 6742 0 16:17 ?        00:00:00 /usr/sap/NPL/DVEBMGS42/exe/igspw_mt -mode=profile -no=0 -restartcount=0 -wdpid=6742 pf=/usr/sap/NPL/SYS/profile/NPL_DVEBMGS42_nplhost
npladm    6757 6742 0 16:17 ?        00:00:00 /usr/sap/NPL/DVEBMGS42/exe/igspw_mt -mode=profile -no=1 -restartcount=0 -wdpid=6742 pf=/usr/sap/NPL/SYS/profile/NPL_DVEBMGS42_nplhost
npladm    7930 1544 0 16:47 pts/1    00:00:00 grep sap
telnet ubuntu64 3242
Trying ::1...
Trying 127.0.1.1...
Trying 10.0.2.15...
telnet: Unable to connect to remote host: Connection refused

Similar Messages

Strange info in "Bypass Proxy Settings for These Hosts and Domains"

For my Mac Mini my Network IP Address always has a self-assigned 169.254 number that I cannot change. Strangely, this same IP number is similar to info that is in the Proxies section (of Network Settings) under "Bypass Proxy Settings for These Hosts and Domains".
No matter what I do, this info (*,local, 169.254/16) appears in my Network Settings in the Proxies section under "Bypass Proxy Settings for These Hosts and Domains". (I tried removing the info and it would cause the "Configure Proxies" selection to default to "Always Use PAC File". Had to go back and retrash all the plist files to have Proxies go back to "Configure Proxies-Manually". Still, the info (*,local, 169.254/16) continues to appear in the "Bypass Proxy Settings for These Hosts and Domains" section and my IP address is always a 169.254 number.)
Comcast cable modem via direct hardwired Ethernet works fine with my other computer, so not the modem. Also, other computer does not have any info in the "Bypass Proxy Settings for These Hosts and Domains" section.
Installed a fresh copy of OS X 11.5 on a new hard drive. Still the same problem.
I posted this issue before but only got one responder and the problem still exists. Any clues? Somebody must know about this stuff. Help please.
Thanks

When your Mac wakes up, it does not yet have an IP Addresss. It wants to send a request to a Router for an apprpriste IP address to use now. But it needs to have an IP address (like a return address) to receive any messages. So, ... wait for it,
... it (your Mac) makes one up. There are rules that ensure it is a random address, but they always start with 169.254. It is on the same subnet with any low-order 16 bits This is the "self-assigned" range of IP Addresses. This address is only good for talking on a local network segment, for things like asking for a valid IP Address from a DHCP-enabled Router.
In most cases, on most networks, the 169.254 self-assigned IP Address is replaced by a valid Local IP Address such as 192.168.xxx yyy or 10.0.xxx.yyy so quickly that you never even see the 169.254 Address.
If you do see the 169.254 Address, it can be read as "Nobody will talk to me" or "Nobody will give me an IP Address". When you have this IP Address for more than an instant, you should suspect bad cables for Ethernet connections, bad signal strength or interference for wireless, Router configuration problems, or Mac configuration problems.
Mac configuration problems are often solved by using the "Assist Me" button is System Preferences > Network and choosing to set up again.
Another diagnostic is to try using Network Utility and the Ping function, and Ping-ing the address of your Airport base Station, often 192.168.0.1 or 10.0.0.1 or similar. This will tell you if the Router is reachable, or there are cabling/wirelss signal problems.
In this case, proxies are not an issue, and are simply a distraction from the real problems.

Correct settings for HDV capture

Hi. I'm using Premiere CS5.5. I went on a few forums to get the correct settings for HDV capture.
I can record the footage fine. However I saw a few things which didn't seem right.
After capturing the HDV footage, the file was a .mpeg file. Secondly, the clip was 1 hour and 10 minutes and
it was only 11.3 GB. Does this sound right? A 55 minute .avi file is 11.6GB. I thought a HDV clip would be quite a large size file.
If this dosen't sound right, is there somewhere I could go to, to check that my settings are correct? By the way I'm filming and capturing with a Canon XHA1.
The footage is 1080i. HDV. I've exported it and it looks fine. Just want to make sure I've captured it correctly and to the best quality.
Thanks for your help.

The HDV format was advanced by Sony and others to use the same miniDV tapes used for SD. In fact, your Canon XHAI can record and play either without changing the tape transport speed.
Your observation in relative file sizes is due to the fact that HDV is highly compressed (MPEG), whereas, SD (AVI) is not as highly compressed. This is one of the reasons folks (such as Harm) don't consider HDV to be an edit format, but just a delivery format.
Note that what Harm was saying is symantics--you capture an analog source through a capture card that digitizes it. When you transfer a image file from HDV or SD, it is already digitized, so a bit-to-bit transfer occurs.

What are the correct settings for the Canon 5D mark II in FCP 7 ?

I am shooting full HD at 23s97 fps.. tried making a preset for the Canon but when I import fils FCP always wants to change to appropriate settings for this file type but doesn't tell me what that is...
(latest firmware installed)
Please, can someone provide all the correct settings for me?
And also, why doesn't the camera show up on the desktop/in the menus when attached to the mac? I have ro use EOS utility every time I want to get anything off of the camera... and FCP doesn't see it either. That's just not right - FCP MUST recognise my camera!! : (
Please help - I don't want to start editing until I have the right settings for this footage.
Thanks
Jim

Welcome to the Boards
Not sure what you mean with the following, looks like a word dropped?
I have ro use EOS utility every time I want to get anything off of the camera...
Anyway, some more specs on your system could help point where the issue is. With the new Plug-In by Canon you can Log & Transfer from the Flash Card (not sure how you connected the camera.) Alternatively you could just drag the files in (but make sure to keep all files such as THM in case you use Log and Transfer later.)
Generally it is best to transcode to Pro Res to be able to work with the files in Final Cut. (Log & Transfer should do that, or using Compressor/Mpeg Streamclip.)
It (Final Cut) is probably changing the timeline to match the codec, or depending on your last preset used, just switching things around. In other words if you were editing in DV and had a set up for that, new sequences would default to that and if you try to ad anything else you will get the message.
Take a look at the search over there -> to look for the Canon 5D threads for some more info.
What I would do is just pull one of the clips in to start and look at what the sequence settings are aftr Final Cut changes them for you - they should be fine generally, though you will want to change Codecs to Pro Res.
I like just batch conversion of all my clips from the 5D Markk II and then work from there. (I do not hook up the camera to the computer, just use a card reader.)

Which are the correct settings for gmail in MacBookPro

I want to use mac mail to access my gmail. Can I ? instead of going directly to web to access my gmail.? Which are the correct settings for the incoming and outgoing servers ?

Hi,
Yes. You can absolutely access your Gmail account from within either Mail or Microsoft Outlook for Mac. Make sure, that you have enabled POP/IMAP in your Gmail settings, then follow the instructions here: http://mail.google.com/support/bin/answer.py?hl=en&answer=180188 if you wish to access your account via POP3 instead of IMAP, change the incoming mail server to pop.gmail.com
Regards,
Gábor

Correct settings for DVD

Hi
I wish to know which are the correct settings for making a new project in imovie and then what to do for getting the best quality on DVD. (I use still pictures and video clips with music, transitions and effects)
Thank you so much.

ola
the correct format depends on the format your camera (PAL or NTSC - 4:3 or 16:9) meaning the project format should meet the camera format. pleas note that that format changes in iMovie/iDVD are effective only for new projects and cannot change existing ones. the dvd quality settings depend on the length of your movie and can be set in iDVD under preferences.
my movies are never longer than 30 min. so i set it to faster encoding and check background encoding ... i also tried with best quality once but frankly i can't see the difference
buona suerte & viva la mela

HT1277 i have all the correct settings for my e mail but i can't send for some reason it keeps taking my outgoing server offline

i have all the correct settings for my e mail but i can't send for some reason it keeps taking my outgoing server offline can anyone help

If you can receive mail and your connection to your ISP is otherwise working, but cannot send mail, then your SMTP settings are incorrect; the SMTP server port is wrong, your SSL setting is wrong, or the username or password credentials don't match what the ISP has, or your attempted accesses are being blocked or your ISP SMTP server is offline.
And in general, don't use port 25 for your outbound mail, unless your ISP specifically requires that; these days, that port is best left to communications between mail servers and (usually) not used by any mail clients.

What are the correct settings for my WRT54GS for using remote access on a Windows Home Server?

I can not remotely access my Windows Home Server from outside. What are the correct settings for my WRT54GS?

I have opened ports 80, 443,and 4125 to PCP. The router address is http://192.168.1.1, my address is 221.40.138.170.
Thank you.

DNS settings for virtual host 10.6 server

We have just gone through a rebranding exercise, i.e. the company name has changed from 'mycompany' to our 'ourcompany'.
For various reasons we have decided to not rename our complete setup, but rather add a virtual host for our mail server including a second primary DNS zone for the new domain 'ourcompany'.
We are hosting our website externally, however since we added the second primary DNS zone incl. an A record (www) pointing to our external website hosts IP for 'ourcompany', workstations on our LAN can no longer access the website.
Running DIG for 'www.ourcompany.com.au' results in the correct A record IP address being shown, but it is still not showing in any browser – we also made sure we emptied our caches.
Although we thought this should work relatively easily, we are now totally confused as to the additional primary zones general settings... currently we allow zone transfer and provide an entry in the nameserver section.
Any ideas as to what might be going on here would be greatly appreciated.

Mr. Hoffman,
Than you very much for your reply - unfortunately, despite studying and testing your advice (incl. wesbite) we seem to not get much further.
Please find our comments inserted below...
MrHoffman wrote:
FWIW, both mycompany.com.au and ourcompany.com.au are real and registered domains; I'll presume they're not the domains you're migrating from or to. Accordingly, I'll use example.org for your old stuff, and example.com for your new stuff; the example domains are RFC-reserved for this usage.
Correct we are not using my bad example domains.
Each host should have one A record (and one AAAA record, if you have IPv6 active), and one of the more common errors in these migrations is setting up an A record for each new domain that might arrive; each host has one A (and possibly one AAAA) record, and that's the canonical name for that host. Externally, that'll probably be the latest name in any sequence (such as www.example.com), and all previous names (including www.example.org) will have CNAME entries.
To clarify do you mean the following: internally we should not have more than one A record for each host... i.e. one for example.org and one for example.com and presumably any other subdomains should be CNAME records?
2. externally we should change the A record for www.example.org to a CNAME record and create a new A record for www.example.com;
Internally (and here's why having a different domain inside is handy) use one of the old names; use example.org, for instance. This means you can use the public DNS services for the external web sites and resources; your internal DNS servers receive the requests for example.com hosts and go "duh, lemme ask somebody else for that", and that somebody else is the (public) DNS server your external DNS services for example.com hosts.
Exactly what we had initially done - basically we (naively) thought we could get away with only relying on external DNS translations... however that resulted in mail clients on our LAN loosing their connection every 5-10 minutes, thus we decided to setup another primary DNS zone which fixed that problem but created the other.
Please also note we have created a subdomain admin.example.com which properly resolves to the CMS backend - btw. from within this backend you can then preview the any page on the regular website with their non www. URLs.
Since the current setup resolves to the correct IP address I wonder if it could be a problem with the .htaccess rewrite rules the web developer has setup to remove the www. ... or is this too far fetched?
The usual trigger for not reaching the external A (or AAAA) records is either a stale cache on the particular client (for translations inside the Time To Live (TTL) values for the old DNS translations, or pending a local cache flush on each client), or (and this is more common) confusion over authoritative DNS servers; you have your internal DNS configured as authoritative for the new www.example.com domain, and also authoritative for the old www.example.org domain, and your external DNS is also authoritative for (probably) both domains. Internal requests get as far as the internal server, and get an authoritative translation (possibly being "no such host"), and don't go any further.
Safari & Firefox present with 'Server not found' errors.
So we are still stuck thus any further advice would be much appreciated.

Anyone have the correct settings for iCloud in Outlook 2011 with OS X 10.7.2 ?

I have tried setting up iCloud in my outlook 2011 on my iMac. I get an error "[AUTHENTICATION FAILED] Authentication failed] Your username/password or security settings may be incorrect.
I have tried several posted settings, for example:
Incoming Server: imap.mail.me.com
Checked Use SSL
Port 993
Outgoing server: smtp.mail.me.com
Checked Overrise default port
Checked Use SSL
Port 587
I have also tried adding p99- in front of both server names, still didn't work.
Anyone have a solution?

Julian Wright wrote:
Here are Microsoft's own instructions for setting up iCloud email in Outlook for Mac:
http://support.microsoft.com/kb/2648915
Just an FYI Julian, Unfortunately in that document MicroSoft have given the Mobile Me server addresses so it doesn't work with iCloud.
If you substitute iCloud server addresses (imap.mail.me.com etc) these instructions work.

Best/correct settings for MSI865PE-LS Bios Vs1.7

I just update bios to Vs 1.7 on my MSI 865PE-LS MB
I would like the best performance settings to run at optimal speed
memory I am using
Dynamic Overclocking: ?
Performance Mode: ?
CPU Ratio Selection: Locked
DRAM Frequency: ?
Spread Spectrum: Disabled
Adjust CPU Bus Clock (Mhz): ?
DDR Clock (Mhz): ?
Adjust AGP/PCI Clock (Mhz): ?
CPU Vcore Adjust: No
CPU VCore: ?
DDR Power Voltage: ?
AGP Power Voltage:?
DRAM Size 1024 MBytes
DRAM Frequency ?
FSB:DRAM ?
CAS# Latency ?
RAS# to CAS# ?
RAS# Precharge ?
Cycle Time (TRAS) ?
# of memory modules 2

Quote
Originally posted by Into Eternity
Dynamic Overclocking: Captain
Performance Mode: Fast
CPU Ratio Selection: Locked
DRAM Frequency: 400
Spread Spectrum: Disabled
Adjust CPU Bus Clock (Mhz): 200/disabled
DDR Clock (Mhz): 400
Adjust AGP/PCI Clock (Mhz): 66/33 default
CPU Vcore Adjust: disabled
CPU VCore: 1.550
DDR Power Voltage: 2.7
AGP Power Voltage:1.5
DRAM Size 1024 MBytes
DRAM Frequency by speed
FSB:DRAM by speed
CAS# Latency by speed
RAS# to CAS# by speed
RAS# Precharge by speed
Cycle Time (TRAS) by speed
# of memory modules 2 - slot 1 and 3
Of course you should try turbo and ultra turbo and faster D.O.T. settings, but I'm taking a guess as to what would work best for you with stability and performance balanced. Post your results or any problems.
thanks (Into Eternity ) your motherboard is different to mine most of the settings would be the same except my bios doesnt have performance mode /IE captain etc
little more info the MSI 865PE-LS setting would still good

Correct settings for your phone

During the last week I have spent many hours trying various settings. I then found a site where you pay £1 and they send the settings to you. It worked very well. I just had to fill in online the details of my phone, its service provider and if it was on a contract or PAYG. No doubt there are several companies who do this. I used "configuremyphone.com" They send the settings on a text to your phone and give you a pin number to use which then moves the settings in the text to the correct locations in your phone.

It probably reset the access point for the browser.
First make sure that the access points are ordered correctly in your internet destinations and also check that "Internet" is the default destination.
Then, from within the browser, check the settings and make sure that it uses "default" as its access point. It will then attempt to connect via the WLAN and, if it's not available, go for the packet data service.
Was this post helpful? If so, please click on the white "Kudos!" star below. Thank you!

Correct settings for SWOP proof

Hi,
I need to export a pdf of an ad created in InDesign and have a "SWOP-certified color proof "
printed. A vendor told me I can just export the pdf as "High quality print." Another vendor tells me
I need to export the pdf with the correct SWOP settings. I'm guessing he's right?
I attached images of my current settings. Am I doing this right?
Thanks so much!
1)
2)
3)

ola
the correct format depends on the format your camera (PAL or NTSC - 4:3 or 16:9) meaning the project format should meet the camera format. pleas note that that format changes in iMovie/iDVD are effective only for new projects and cannot change existing ones. the dvd quality settings depend on the length of your movie and can be set in iDVD under preferences.
my movies are never longer than 30 min. so i set it to faster encoding and check background encoding ... i also tried with best quality once but frankly i can't see the difference
buona suerte & viva la mela

Correct settings for using varDisplayTopic Title and varTopicTitle

Say I have a module 20 screens long (CP4 by the way) with four topics. The template I'm using was set up by someone else, but had the $$varDisplayTopicTitle$$ and the $$varTopicTitle$$ already defined.
Titles are assigned TopicTitle01 through TopicTitle04 in the Project>Actions, along with varDispalyTopicTitle.
Correct me if I'm wrong, but the first page of my first topic shold be set to:
Label: Topic01 Page01
On slide enter: Assign
Assign: varTopicTitle01
with: Understanding Our Products
For the pages following topic 01, what should my settings should be? Do I need to label every page (e.g., Topic 01 Page 02, Topic 01 Page 03) after the first Topic page? Do I use Execute Advanced Action and Set Topic Title for the pages to follow. Or do I use the Assign again?
Much thanks in advance!
JT

Hello,
OK, now it is very clear, thanks to the screenshots.
From your first screenshot, I deduct that you already created the 3 extra user variables you do need: varTopicTitle11, varTopicTitle12 and varTopicTitle13. And I think you gave them as values the complete title of each topic.
How do I wish that Captivate 5 were already there, this kind of actions is so much easier to create there (I'm not an Adobe employee, be sure, just happy to have been a tester for this new version).
Will try to explain step by step: you'll have to add 3 more conditions to your already long action SetTopicTitle. They are quite similar to all the (10) others, so for Topic11 it will be:
Check if cpInfoCurrentSlideLabel contains Topic11
Begin
varDisplayTopicTitle = varTopicTitle11
End
Nothing is needed as Else statement.
Do not know if you ever wrote such an action? The interface is a bit 'clumsy' (explains my sigh about CP5). After choosing the action, scroll to the end after the last statement:
select 'Add statement'
use the space bar to open the dropdown-list, for the first action, choose Condition
after 'Check if' select 'Select variable', use the space bar to open the dropdown-list, choose varDisplayTopicTitle
select 'is equal to', use the space bar to open the dropdown-list, choose contains
double-click (or space bar) to choose variable out of choice between variable and value
open the dropdown list with variables (space bar) and choose varTopicTitle11
You can leave the rest as it is. Repeat the same steps for the two other Topics.
Since you are using the same advanced action on each start of Topic, there you'll have nothing to change.
Hope this helps?
Lilybiri

Final cut won't export the correct settings for MXF videos

I have final cut 10.2 and compressor 4.2. My video footage is DSLR media shot at 1920x1080 at 29.97 in Mpeg format. I create an NTSC timeline that is 29.97 and 1080P and I can import and edit with this no problem. My issue is i want to export as 1080i29.97 XDCAM HD 422 50 Mbps in MXF format.(their is a preset for this in compressor) What i get is an mxf file that is 720x576 at 25 FPS and the picture is squished. I added the destination through Final cut to compressor and selected the preset i want. I also checked the preset and the settings are correct. You can see from the picture below.
However when i select this destination from Finalcut 10 it shows in the settings that it is 1080i and also 720x576 on the same page! You can see from the image below that the title of the destination is "1080i29.97 XDCAM HD 422 50 Mbps" and below that it says 1080i, 8ch 24bit mono tracks. But at the bottom of this menu it says 720 x 576 | 25 fps!
if i export as a master file this does not happen, even if i choose XD CamEX 50Mbps. Any help is appreciated. Not sure what is going on. Thanks

What player are you using for playback?
Did you update the Pro Video codecs?
My export is showing this
and the output shows this

SAP on Ubuntu Correct settings for etc/hosts?

Similar Messages

Maybe you are looking for