SCE pcube-SE-MIB traffic-counters error

Hi,
On both the SCE 1010 and SCE 2020, I am seeing the following error:
#sh snmp MIB pcube-SE-MIB traffic-counters
Error - internal error: was not able to retreive Traffic-Counter information
I am running the following version:
#sh ver
System version: Version 3.6.1 Build 13
Build time: Jul 25 2010, 23:45:29 (Change-list 631208)
Software version is: Version 3.6.1 Build 13
Does anyone know why traffic-counters is returning this error when all of the other pcube-SE-MIB sub-options work?
#sh snmp MIB pcube-SE-MIB subscriber
subscribersNumIntroduced = 0
subscribersNumFree = 199999
subscribersNumIpAddrMappings = 0
subscribersNumIpAddrMappingsFree = 200000
subscribersNumIpRangeMappings = 0
subscribersNumIpRangeMappingsFree = 7972
subscribersNumVlanMappings = 0
subscribersNumVlanMappingsFree = 0
subscribersNumTpIpRanges = 0
subscribersNumTpIpRangesFree = 0
subscribersNumActive = 0
subscribersNumActivePeak = 1
subscribersNumActivePeakTime = 5 weeks, 5 days, 7 hours, 58 minutes, 16 seconds
subscribersNumUpdates = 2
subscribersCountersClearTime = 5 weeks, 5 days, 8 hours, 1 minutes, 28 seconds
subscribersNumAnonymous = 0
Regards, Brett.

Hi Brett,
Did you configure traffic-counter on SCE ?
If there is no configuration of traffic-counter, you can see this error.
Can you try to configure as following ?
SCE2000#>conf
SCE2000(config)#>interface LineCard 0
SCE2000(config if)#>traffic-counter name test count-bytes
SCE2000(config if)#>end
SCE2000#>show snmp MIB pcube-SE-MIB traffic-counters
trafficCounterIndex.1.1 = 1
trafficCounterValue.1.1 = 0
trafficCounterName.1.1 = test
trafficCounterType.1.1 = bytes
Error - internal error: was not able to retreive Traffic-Counter information
SCE2000#>
Thanks,
Keita

Similar Messages

CLI Output filter - show int counters errors

Hi,
On catalyst and Nexus, I would like to filter the lines with 0 0 0 0 0 from the "show int counters errors" result.
Result without filter :
Switch#sh int counters errors
Port        Align-Err    FCS-Err   Xmit-Err    Rcv-Err UnderSize OutDiscards
Gi1/1               0          0          0          0         0           0
Gi1/2               0          0          0          0         0           0
Gi1/3               0          0          0          0         0           0
Gi1/4               0          0          0          0         0           0
Gi1/5               0          0          0          0         0           0
Gi1/6               0          0          0          0         5500     0
Gi1/7               0          0          0          0         0           0
Gi1/8               0          0          0          0         0           6005
My expected result
Switch#sh int counters errors | exclude or grep ???
Port        Align-Err    FCS-Err   Xmit-Err    Rcv-Err UnderSize OutDiscards
Gi1/6               0          0          0          0         5500     0
Gi1/8               0          0          0          0         0           6005
Thank you for your help.
Regards.
Ju

These kind of lines are filtered:
sh int counters errors | ex 0(.*)0(.*)0(.*)0(.*)0(.*)0
Gi1/0/12            0           0           0           0          0           83
Gi2/0/20            0           0           0           0          0      5343759
Gi2/0/21            0           0           0           0          0      5343135
Gi2/0/22            0           0           0           0          0      5344382
Po2                 0           0           0           0          0          104
Thank you for your help.
Ju

SCE does not capture traffic snmp get-request

Hi,
We have SCE 2000 3.5.5.
I have a problem to capture some snmp traffic.
From a server To a router, our SCE captures traffic snmp "GET-NEXT-REQUEST". I can see these traffic in RDR (Transaction RDR and Subscriber RDR).
but, From the same server To the same router, "GET-REQUEST" doesn't.
I have checked these packets using sniffer software, and the difference of these is only "GET-NEXT-REQUEST" or "GET-REQUEST".
What could cause this situation??
Help me!

Hi, Tom.
I have controlled that the port is 161 and these packets go through the same SCE.
I changed the service configuration as you said, but SCE didn't caputured the packets "snmp-get". I write the way that I have done.
     1.     Open "New Service Configuration"
     2.     Add 161 to "UDP ports for which flow should be opened on first packet"
     3.     "RDR Settings" - "Transaction Usage RDRs" - check "select ALL"
     4.     Apply a SCE device
     5.     command "Snmpget" from a pc
     6.     Control RDRs with tag "4042323000" --> No record from the pc
     7.     mib-browser from the same pc
     8.     Control RDRs with tag "4042323000" --> find the record from the pc
I hope i can resolve it soon.

Traffic lighting error

Hi,
I'm using OBIEE 11g to build a dashboard that makes use of traffic light conditional formatting. However, it seems that on a grid on the dashboard, some values are not generating a traffic light image despite the fact they are within the range covered by the traffic light formatting. I have applied the formatting to entire columns, not just to individual cells. Does anyone know of anything common that might be causing this error?
Thanks.

I have started OC4J_UM (it shows internall error message when i start traffic cop so it loads it).
Traffic cop did not leave messages in Appache because server did its part and i found UM Webmail Client Log and it says :
((time 10/20/2003 14:43:33.006 CEST)(compclass Webmail_Client)(compinst 0)(component Webmail_Client)(module traffic_cop.executeAction())(priority error 6)(execid 127.0.0.1:641909560.ApplicationServerThread-25:1066653813-1)(msgid <null>)(mtext ERROR: Unexpected error java.lang.NullPointerException occurred during action module processing: null))
((time 10/20/2003 14:43:33.007 CEST)(compclass Webmail_Client)(compinst 0)(component Webmail_Client)(module traffic_cop.processRequest())(priority error 6)(execid 127.0.0.1:641909560.ApplicationServerThread-25:1066653813-2)(msgid <null>)(mtext Error caught during action; checking for logout flag))

11g performance counters error on Server 2003

Environment - fresh install of 11g (11.1.0.6.0) on a fresh Server 2003 R2 box. All configuration is largely out-of-the-box.
When I start the "Oracle Counters for Windows Performance Monitor" item from the start menu, I get a dialog box error with the following:
Unable to add these counters:
\Oracle11 Sorts(0)\sorts in memory/sec
\Oracle11 Sorts(0)\sorts on disk/sec
Clicking OK to that error, Performance Monitor does come up but when I try to add a counter, there is no Oracle-related Performance Object to choose, just the standard Windows, ASP, etc. ones.
Any ideas?

Personally I'd rather use Grid Control on x86-64 Linux.
But, I was asking about the error message I'm getting in hopes that perhaps someone else has seen this to. I wasn't asking what operating system to choose for Oracle, nor what management tool is best, though I do appreciate your feedback. As for why: simple curiousity. I want to poke around to see how 11g metrics are exposed and instrumented within Windows' own management frameworks, since I run into Oracle-on-Windows quite a bit. Pushing buttons in test environments just to see what they do is how we learn the strengths and weaknesses of all these technology products.

En-Countering Error While trying to Open the Database

Hi Everybody,
Database Version:Oracle9i Enterprise Edition Release 9.2.0.4.0 - 64bit Production
Os: Solaris9
This is one of our Test Database which is running in No-Archivelog Mode and having no backup of Physical Datafiles.
Due to some Server issues the Database was Shutdown Abnormally after which when we are trying to open our DB it showing the following Error......
ORA-01172: recovery of thread 1 stuck at block 13447 of file 216
ORA-01151: use media recovery to recover block, restore backup if needed....
we are also not able to perform a media recovery since the database is running in No-Archivelog Mode....
The only way we know to bring up the Database is making the Datafile=216 offline and opening the Database...
In there any workaround in order to resolve the Block corruption of Data-File 216........Since we will be needing the data located in datafile 216.
Any help Appreciated,
Thanks & Regards,
Prosenjit Mukherjee

DBVERIFY: Release 9.2.0.4.0 - Production on Thu Feb 26 15:37:47 2009
Copyright (c) 1982, 2002, Oracle Corporation. All rights reserved.
DBVERIFY - Verification starting : FILE = /sts/oradata/npm/sts/STPUSER10.dbf
DBVERIFY - Verification complete
Total Pages Examined : 98304
Total Pages Processed (Data) : 97673
Total Pages Failing (Data) : 0
Total Pages Processed (Index): 1
Total Pages Failing (Index): 0
Total Pages Processed (Other): 570
Total Pages Processed (Seg) : 0
Total Pages Failing (Seg) : 0
Total Pages Empty : 60
Total Pages Marked Corrupt : 0
Total Pages Influx : 0
This is the Output of the Dbverify Utility,but as i can see "Total Pages Marked Corrupt : 0"
its telling me that neither of the blocks are corrupted......
Earlier when i was trying to do a Recovery it was giving me the Following Error....
ORA-01172: recovery of thread 1 stuck at block 13447 of file 216
ORA-01151: use media recovery to recover block, restore backup if needed.........

High 802.11 MAC Counters Errors on WLC

When I log into our WLC I see a very high TX Failed, ACK Failure, RTS Failure and FCS Error Counts. Is this normal? How can I troubleshoot this problem? We have 10 LAPs that are in the same network as the managed and ap manager interfaces on the WLC. Thanks.

Quantify very high please. Truly very high error rates usually are due to multipath issues in your RF network. However, MTU size can also have an effect. If you could, please send over a list of errors from a 10 minute slice of time under normal load. This will assist us in understanding your network. Also, please include client device types and overall network environment on the RF side.

LMS 4.1 error unable to load the MIB file

when load MIB file have error unable to load the MIB file Error: can't find RFC1155-SMI
I can not find RFC1155-SMI.my Where I can find or download RFC1155-SMI.my
Thank

The following thread has RFC-1212.my in it. You can downlaod from there :
https://supportforums.cisco.com/thread/174886
Mostly all the Cisco MIB will be available @ :
ftp://ftp.cisco.com/pub/mibs/v1/ OR ftp://ftp.cisco.com/pub/mibs/v2/
The above you requested are non-cisco mib, which can be extracted either from RFC or they canbe found in some univerisites FTP or some free sites like oidview :
http://www.oidview.com/mibs/detail.html
-Thanks
Vinod

Cisco SCE 8000 rebooting

Hi!
Cisco SCE 8000 working normally while traffic through it not pass. When i connect optical links and start passing traffic throught cisco, i have a problem. SCE watchdog run software reboot with error:
2013-09-30 13:54:40 | FATAL | CPU #000 | A problem occurred in the SCE8000 Service Control Module Extended (SCM-E) slot 1 ,Please report to Cisco's customer support.
2013-09-30 13:54:40 | ERROR | CPU #000 | SE Watchdog Module: An Error occurred. Please report to Cisco's customer support
2013-09-30 13:54:40 | ERROR | CPU #000 | SE Watchdog Module: An Error occurred. Please report to Cisco's customer support
2013-09-30 13:54:41 | WARN | CPU #000 | SE Watchdog Module: A problem occurred. Please report to Cisco's customer support
2013-09-30 13:54:41 | INFO | CPU #000 | Party data base was closed.
In debug file i found:
Interrupt Received from: SimbaDPT[0].Tx[0].CTX_ISR.ECCMultiErrorInt - description: RLDRAM ECC multi bit error interrupt.
What the problem could be?

I have tried 3.7.2, 3.8.5, 4.0.0. Unfortunately, the result is the same. I think that hardware problem (RAM).

Another TCP Reassembly Queue Issue - Help Understanding Sh IP Traffic Results

I recently started seeing the TCP Out-of-Order blurbs on my 1921/k9 routers logs. See following....
*Oct 28 06:41:32.793: %FW-4-TCP_OoO_SEG: Dropping TCP Segment: seq:-1475532578 1500 bytes is out-of-order; expected seq:2819411594. Reason: TCP reassembly queue overflow - session 192.168.10.11:58675 to 23.77.232.34:80 on zone-pair ccp-zp-in-out class ccp-protocol-http
*Oct 28 15:09:21.539: %FW-4-TCP_OoO_SEG: Dropping TCP Segment: seq:79628295 1488 bytes is out-of-order; expected seq:79600783. Reason: TCP reassembly queue overflow - session 192.168.10.25:55690 to 206.19.48.10:80 on zone-pair ccp-zp-in-out class ccp-protocol-http
*Oct 28 15:16:44.803: %FW-4-TCP_OoO_SEG: Dropping TCP Segment: seq:-1210068379 1500 bytes is out-of-order; expected seq:3084764253. Reason: TCP reassembly queue overflow - session 192.168.10.13:50591 to 107.167.193.162:80 on zone-pair ccp-zp-in-out class ccp-protocol-http
I temporarily disabled TCP Queue length logs (setting to 0) after having changed to several options including 128 and 1024 did not help. The output of Sh IP Traffic....
"Router#sh ip traffic
IP statistics:
Rcvd: 411466 total, 163659 local destination
0 format errors, 0 checksum errors, 2 bad hop count
0 unknown protocol, 1 not a gateway
0 security failures, 0 bad options, 0 with options
Opts: 0 end, 0 nop, 0 basic security, 0 loose source route
0 timestamp, 0 extended security, 0 record route
0 stream ID, 0 strict source route, 0 alert, 0 cipso, 0 ump
0 other
Frags: 0 reassembled, 0 timeouts, 0 couldn't reassemble
0 fragmented, 0 fragments, 0 couldn't fragment
Bcast: 162854 received, 415 sent
Mcast: 0 received, 0 sent
Sent: 5560 generated, 18211176 forwarded
Drop: 22 encapsulation failed, 0 unresolved, 0 no adjacency
2383 no route, 0 unicast RPF, 0 forced drop
0 options denied
Drop: 0 packets with source IP address zero
Drop: 0 packets with internal loop back IP address
0 physical broadcast
ICMP statistics:
Rcvd: 0 format errors, 0 checksum errors, 0 redirects, 0 unreachable
11 echo, 0 echo reply, 0 mask requests, 0 mask replies, 0 quench
0 parameter, 0 timestamp, 0 timestamp replies, 0 info request, 0 other
0 irdp solicitations, 0 irdp advertisements
0 time exceeded, 0 info replies
Sent: 2028 redirects, 2809 unreachable, 35 echo, 11 echo reply
0 mask requests, 0 mask replies, 0 quench, 0 timestamp, 0 timestamp replies
0 info reply, 2 time exceeded, 0 parameter problem
0 irdp solicitations, 0 irdp advertisements
BGP statistics:
Rcvd: 0 total, 0 opens, 0 notifications, 0 updates
0 keepalives, 0 route-refresh, 0 unrecognized
Sent: 0 total, 0 opens, 0 notifications, 0 updates
0 keepalives, 0 route-refresh
PIMv2 statistics: Sent/Received
Total: 0/0, 0 checksum errors, 0 format errors
Registers: 0/0 (0 non-rp, 0 non-sm-group), Register Stops: 0/0, Hellos: 0/0
Join/Prunes: 0/0, Asserts: 0/0, grafts: 0/0
Bootstraps: 0/0, Candidate_RP_Advertisements: 0/0
Queue drops: 0
State-Refresh: 0/0
IGMP statistics: Sent/Received
Total: 0/0, Format errors: 0/0, Checksum errors: 0/0
Host Queries: 0/0, Host Reports: 0/0, Host Leaves: 0/0
DVMRP: 0/0, PIM: 0/0
Queue drops: 0
TCP statistics:
Rcvd: 39 total, 0 checksum errors, 37 no port
Sent: 2 total
EIGRP-IPv4 statistics:
Rcvd: 0 total
Sent: 0 total
UDP statistics:
Rcvd: 163487 total, 0 checksum errors, 162603 no port
Sent: 695 total, 0 forwarded broadcasts
OSPF statistics:
Last clearing of OSPF traffic counters never
Rcvd: 0 total, 0 checksum errors
0 hello, 0 database desc, 0 link state req
0 link state updates, 0 link state acks
Sent: 0 total
0 hello, 0 database desc, 0 link state req
0 link state updates, 0 link state acks
ARP statistics:
Rcvd: 3651888 requests, 72 replies, 0 reverse, 0 other
Sent: 159 requests, 28560 replies (225 proxy), 0 reverse
Drop due to input queue full: 0"
Would someone be so kind as to help me understand a little about my IP Traffic and what might be going wrong? Thanks for any input. --Tim

With Queue Length set to 1024:
Router>show ip inspect statistics
Interfaces configured for inspection 4294967294
Session creations since subsystem startup or last reset 0
Current session counts (estab/half-open/terminating) [0:0:0]
Maxever session counts (estab/half-open/terminating) [0:0:0]
Last session created never
Last statistic reset never
Last session creation rate 0
Maxever session creation rate 0
Last half-open session total 0
TCP reassembly statistics
received 0 packets out-of-order; dropped 0
peak memory usage 0 KB; current usage: 0 KB
peak queue length 0

No display of error message log in dialog box

Dear MM Experts,
During enter incoming invoice (MIRO), when we click simulate after entering all necessary data, all error & warning messages are displayed in a dialog box if there is red traffic light. In our case despite red traffic light error messages are not displayed as shown in below screen shot. Only warning messages are displayed & document canu2019t be posted. Please let me know if anyone has encountered such behavior & knows the solution. We just want to see the error messages in dialog boxes so that necessary data can be entered and document can be posted.
Additional information: 1. No GR needs to be done, 2. GR based IV is unchecked in PO, 3. No validation is active for the company code,
Thanks & regards,
Avinash

Hi,
Thanks for your response.
Our problem is not to post a particular invoice doument, the main problem is that error log is not displayed in MIRO. For example if balance is not zero then this error should be displayed in error log dialog box, which is not happening due to which we are not able to post any invoice document as error is not known to the user. Please let me know if any suggestions.
Additional information: We have deactivated all validations & BADis. We also tried to compare with other systems where error log is displayed properly however our ABAP consultant could not find any difference. Any Input on how to compare is also welcome.
Thanks & best regards,
Avinash

Error Code: -2147024891 (Access is denied)

Hi
I've just installed a new SCOM 2007 R2 server and I added some servers to it, but only in all the Windows 2008 servers that have Exchange 2007 SP3 I can not install the SCOM agent, even if I try to manually install the agent, raise this error and
the installation rolls back, this is the screen:
I tried to follow this link to solve the problem:
http://social.technet.microsoft.com/Forums/sqlserver/en-US/44192faa-12cc-4bd7-9605-0d9ae1444f37/scom-2007-r2-error-25211-failed-to-install-performance-counters-error-code-2147024891-access?forum=operationsmanagergeneral
But when I try to rebuild the counters with lodctr /r, but I have the response "Error: Unable to rebuild performance counter setting from system backup store, error code is 5", the most rare is that
I used the domain admin user and the local admin user, so I don't know what permission it's necessary to install or rebuild the counters.
No one process is using the counters, so may be the problem could be permissions, but this is not sense to me cause I'm using the highest privileges account in the domain...

Hi Alexis
Thanks for the tip, but did not work, the run as administrator was done before, and the error 5 still is raising... :(
When I ran lodctr /r (with "Run As Administrator") in the application Event Viewer raise this about LoadPerf:
3001: The performance counter name string value in the registry is not formatted correctly. The malformed string is 2182. The first DWORD in the Data section contains the index value
to the malformed string while the second and third DWORDs in the Data section contain the last valid index values.
System
- Provider
   [ Name] Microsoft-Windows-LoadPerf
   [ Guid] {122EE297-BB47-41AE-B265-1CA8D1886D40}
   [ EventSourceName] LoadPerf
- EventID 3001
   [ Qualifiers] 49152
   Version 0
   Level 2
   Task 0
   Opcode 0
   Keywords 0x80000000000000
- TimeCreated
   [ SystemTime] 2013-12-22T01:36:13.000Z
   EventRecordID 193126
   Correlation
- Execution
   [ ProcessID] 0
   [ ThreadID] 0
   Channel Application
   Computer HT02.domain.com
   Security
- UserData
- EventXML
   param1 2182
   binaryDataSize 16
   binaryData 860800003607000037070000C3010000
When I try to install manually the agent (amd64\MOMAgent.msi), this events raise:3001,3013, 3009 and repeat 3001, 3013 and 3009, all them about Loadperf too:
3001: The performance counter name string value in the registry is not formatted correctly. The malformed string is 2182. The first DWORD in the Data section contains the index value
to the malformed string while the second and third DWORDs in the Data section contain the last valid index values.
System
- Provider
   [ Name] Microsoft-Windows-LoadPerf
   [ Guid] {122EE297-BB47-41AE-B265-1CA8D1886D40}
   [ EventSourceName] LoadPerf
   - EventID 3001
   [ Qualifiers] 49152
    Version 0
    Level 2
    Task 0
    Opcode 0
    Keywords 0x80000000000000
   - TimeCreated
   [ SystemTime] 2013-12-22T01:20:37.000Z
    EventRecordID 193110
    Correlation
   - Execution
   [ ProcessID] 0
   [ ThreadID] 0
    Channel Application
    Computer HT02.domain.com
    Security
- UserData
- EventXML
   param1 2182
    binaryDataSize 16
    binaryData 860800003607000037070000C3010000
3013: Unable to update the performance counter strings defined for the 009 language ID. The first DWORD in the Data section contains the error code.
System
- Provider
   [ Name] Microsoft-Windows-LoadPerf
   [ Guid] {122EE297-BB47-41AE-B265-1CA8D1886D40}
   [ EventSourceName] LoadPerf
- EventID 3013
   [ Qualifiers] 49152
   Version 0
   Level 2
   Task 0
   Opcode 0
   Keywords 0x80000000000000
- TimeCreated
[ SystemTime] 2013-12-22T01:20:37.000Z
   EventRecordID 193111
   Correlation
- Execution
[ ProcessID] 0
[ ThreadID] 0
   Channel Application
   Computer HT02.domain.com
   Security
- UserData
- EventXML
   param1 009
   binaryDataSize 8
   binaryData 050000006F0D0000
3009: Installing the performance counter strings for service HealthService (HealthService) failed. The first DWORD in the Data section contains the error code.
System
- Provider
   [ Name] Microsoft-Windows-LoadPerf
   [ Guid] {122EE297-BB47-41AE-B265-1CA8D1886D40}
   [ EventSourceName] LoadPerf
- EventID 3009
   [ Qualifiers] 49152
   Version 0
   Level 2
   Task 0
   Opcode 0
   Keywords 0x80000000000000
- TimeCreated
   [ SystemTime] 2013-12-22T01:20:37.000Z
   EventRecordID 193112
   Correlation
- Execution
   [ ProcessID] 0
   [ ThreadID] 0
   Channel Application
   Computer HT02.domain.com
   Security
- UserData
- EventXML
   param1 HealthService
   param2 HealthService
   binaryDataSize 8
   binaryData 05000000F1120000
And finally 10005: -- -2147024891 (Access is denied.).
System
- Provider
   [ Name] MsiInstaller
- EventID 10005
   [ Qualifiers] 0
   Level 2
   Task 0
   Keywords 0x80000000000000
- TimeCreated
   [ SystemTime] 2013-12-22T01:20:53.000Z
   EventRecordID 193116
   Channel Application
   Computer HT02.Domain.com
- Security
   [ UserID] S-1-5-21-2805081708-1522538877-527695900-1142023
- EventData
   Product: System Center Operations Manager 2007 R2 Agent -- Error 25211.Failed to install performance counters.. Error Code: -2147024891 (Access is denied.).
   (NULL)
   (NULL)
   (NULL)
   (NULL)
   7B32353039373737302D324231462D343946362D414239442D3143373038423936323632417D
Binary data:
In Words
0000: 3035327B 37373739 42322D30 342D4631
0008: 2D364639 44394241 3743312D 39423830
0010: 32363236 7D41
In Bytes
0000: 7B 32 35 30 39 37 37 37   {2509777
0008: 30 2D 32 42 31 46 2D 34   0-2B1F-4
0010: 39 46 36 2D 41 42 39 44   9F6-AB9D
0018: 2D 31 43 37 30 38 42 39   -1C708B9
0020: 36 32 36 32 41 7D         6262A}

I cannot start the "SQL Server Reporting Services (SCE)" service

Attempts to run any of the Windows Computer Reports fail with an error:
Date: 10/29/2008 10:19:30 AM
Application: System Center Essentials
Application Version: 6.0.1251.0
Severity: Error
Message: Cannot initialize report.
Microsoft.Reporting.WinForms.ReportServerException: The Report Server Windows service 'ReportServer$SCE' is not running. The service must be running to use Report Server. (rsReportServerServiceUnavailable)
   at Microsoft.Reporting.WinForms.ServerReport.GetExecutionInfo()
   at Microsoft.Reporting.WinForms.ServerReport.GetParameters()
   at Microsoft.EnterpriseManagement.Mom.Internal.UI.Reporting.Parameters.ReportParameterBlock.Initialize(ServerReport serverReport)
   at Microsoft.EnterpriseManagement.Mom.Internal.UI.Console.ReportForm.SetReportJob(Object sender, ConsoleJobEventArgs args)
My attempts to start the "SQL Server Reporting Services (SCE)" service fail with an error:
Could not start the SQL Server Reporting Service (SCE) service on Local Computer.
Error 1053: The service did not respond to the start or control request in a timely fashion.
The application log in the event viewer has hundreds of instances of Event ID 107:
Event Type: Error
Event Source: Report Server (SCE)
Event Category: Management
Event ID: 107
Date:  10/29/2008
Time:  10:36:25 AM
User:  N/A
Computer: DC
Description:
Report Server (SCE) cannot connect to the report server database. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Please help.

Thanks for the link to the Reporting Services forum. I found the fix in this thread:
https://forums.microsoft.com/MSDN/ShowPost.aspx?PostID=3644545&SiteID=1
I had to create a registry key and reboot:
1.
Click Start, click Run, type regedit, and then click OK.
2.
Locate and then click the following registry subkey:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control
3.
In the right pane, locate the ServicesPipeTimeout entry.
Note If the ServicesPipeTimeout entry does not exist, you must create it. To do this, follow these steps:
a.
On the Edit menu, point to New, and then click DWORD Value.
b.
Type ServicesPipeTimeout, and then press ENTER.
4.
Right-click ServicesPipeTimeout, and then click Modify.
5.
Click Decimal, type 60000, and then click OK.
This value represents the time in milliseconds before a service times out.
6.
Restart the computer.
After the reboot, the service was running. Thanks for your help with this.

Output Error Counts

Hello, I'm seeing the same number of output errors across multiple ports on one of our Nexus pairs. Each port has the same vlan in common and I'm wondering if there is any way to narrow down exactly where these errors are starting. From what I've read it's most likely a bad packet since many if not all of the 'show interface counters errors' are zeroed out. Would a sniffer be needed? If so what exactly would I be searching for? Many thanks!

Hi gbzheng,
I think I need a little clarification for your request to better answer your question. Are you trying to count both rising and falling edges in a specific time period, or are you just trying to count the falling edges (errors) in a specific time period?
DAQmx Shipping Examples
If you need deterministic timing using an external clock, I would recommend using the Counter – Count Edges (Continuous Clock) example.
If you do not need the deterministic timing, you could just use the software timed Counter – Count Edges example.
For either example you will need to create a constant (or control) for the edge input on the DAQmx Create Virtual Channel.vi. You will need to specify Falling as the edge type because rising is the default value.
Sam B.
Applications Engineer
National Instruments

Too large frames/Outdiscards errors

Hi !
We have a problem with switch connected to an IBM Chassis (model : WS-CBS3012-IBM-I).
Several links seem to flap from time to time and we have dropped packets (Outdiscards) :
XXX#show interfaces counters errors
Port        Align-Err     FCS-Err    Xmit-Err     Rcv-Err UnderSize OutDiscards
Gi0/7               0           0           0           0          0        43983
XXX#show controllers ethernet-controller gigabitEthernet 0/7
     Transmit GigabitEthernet0/7              Receive
   2584788113 Bytes                        971769475 Bytes
   2128747524 Unicast frames              2142250737 Unicast frames
     10109338 Multicast frames                  7644 Multicast frames
     11694673 Broadcast frames                  1660 Broadcast frames
            0 Too old frames               991831483 Unicast bytes
            0 Deferred frames                 726180 Multicast bytes
            0 MTU exceeded frames             106240 Broadcast bytes
            0 1 collision frames                   0 Alignment errors
            0 2 collision frames                   0 FCS errors
            0 3 collision frames                   0 Oversize frames
            0 4 collision frames                   0 Undersize frames
            0 5 collision frames                   0 Collision fragments
            0 6 collision frames
            0 7 collision frames                   0 Minimum size frames
            0 8 collision frames           208582465 65 to 127 byte frames
            0 9 collision frames           286273443 128 to 255 byte frames
            0 10 collision frames           15408397 256 to 511 byte frames
            0 11 collision frames           12313490 512 to 1023 byte frames
            0 12 collision frames           10599137 1024 to 1518 byte frames
            0 13 collision frames                  0 Overrun frames
            0 14 collision frames                  0 Pause frames
            0 15 collision frames
            0 Excessive collisions                 0 Symbol error frames
            0 Late collisions                      0 Invalid frames, too large
            0 VLAN discard frames         1609083109 Valid frames, too large
            0 Excess defer frames                  0 Invalid frames, too small
       320523 64 byte frames                       0 Valid frames, too small
    396763728 127 byte frames
      6601722 255 byte frames                      0 Too old frames
     28139208 511 byte frames                      0 Valid oversize frames
      4064656 1023 byte frames                     0 System FCS error frames
    285633065 1518 byte frames                     0 RxPortFifoFull drop frame
   1429028633 Too large frames
            0 Good (1 coll) frames
            0 Good (>1 coll) frames
The interface is Full-1000 and is configured :
interface GigabitEthernet0/7
description "SRV-001-PRD-VM1 - VMNic0"
switchport trunk allowed vlan 11,12,99
switchport mode trunk
link state group 1 downstream
end
For the "too large frames", I have already read the post : https://supportforums.cisco.com/discussion/11034901/too-large-frames-what-does-mean-performance, so, I think it's not serious.
But I don't know why some packets are dropped because the configuration seems good ...
Can you help me please ?
Thank you in advance !

87752686 Valid frames, too large
This is nothing. You get this counters if the port(s) is/are configured as Dot1Q Trunking.
There is nothing to be worried about.

SCE pcube-SE-MIB traffic-counters error

Similar Messages

Maybe you are looking for