Signal in interval
Hi
I'm using NI PCI-60l40E to acquire current. I have 9 inputs which for each one I must check if the amplitude of the signal stays between [-x,x] (x is constant that I get from a .txt file for example x = 0.2) for 100 milliseconds according to the result I get a Boolean (true or false). My problem is that I can't follow the signal for 100 milliseconds because I can't extract the time from my signal which is a dynamic data and I don't want to use arrays to avoid memory saturation because I will have more inputs later.
Attachments:
stabilisation.vi 57 KB
Hi again Mike, I really appreciate your help
Well I've tried your suggestion and it works. But let me give you more details, after switching off a contact I'll have a switch bounce phenomenon which I'm supposed to measure the time that it takes and after that I must check that my waveform stays in range for 100 msec, that's why I need to extract the abscissa (from the X axis) of the point just after the bouncing of the signal and start tracking my waveform starting from that time. I've attached a photo to explain more. Thanks
Attachments:
picture 1.png 88 KB
Similar Messages
-
Config air-lap1041n-e-k9 with cisco 5500 (5508) series wireless controller. how to?
Hi!
I try to configure a Cisco 5508 Wireless controller and 25 Air-lap1041 to use as VoIP and data. I read documents, manuals, etc, but the AP doesn't charge the configuration, or not conect with the Wireless Controller, why? No Radius server present, only WPA security.howto, please...
I try to put a static ip in the LAP, with lwapp or capwap command, (LWAPP/CAPWAP ap ip address direccion mascara) and the AP returns "You should configure Domain and Name Server from controller CLI/GUI." and i can't change the name of the AP (Command is disabled).
Log from AP:
using ÿÿÿÿ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x00000184
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
PCIE1 port 1 not initialize
PCIEx: initialization done
flashfs[0]: 6 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 2369024
flashfs[0]: Bytes available: 30016000
flashfs[0]: flashfs fsck took 21 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 44:2b:03:dc:09:25
Ethernet speed is 1000 Mb - FULL duplex
Loading "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx"...###########################
File "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x4000
executing...
enet halted
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
flashfs[1]: 6 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 32126976
flashfs[1]: Bytes used: 2369024
flashfs[1]: Bytes available: 29757952
flashfs[1]: flashfs fsck took 7 seconds.
flashfs[1]: Initialization complete.
flashfs[2]: 0 files, 1 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 11999232
flashfs[2]: Bytes used: 1024
flashfs[2]: Bytes available: 11998208
flashfs[2]: flashfs fsck took 1 seconds.
flashfs[2]: Initialization complete....done Initializing flashfs.
Ethernet speed is 1000 Mb - FULL duplex
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1041N-E-K9 (PowerPC405ex) processor (revision B0) with 98294K/32
768K bytes of memory.
Processor board ID FCZ1611W414
PowerPC405ex CPU at 333Mhz, revision number 0x147E
Last reset from reload
LWAPP image version 7.0.94.21
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 44:2B:03:DC:09:25
Part Number : 73-14034-04
PCA Assembly Number : 800-34273-05
PCA Revision Number : A0
PCB Serial Number : FOC16075VZ3
Top Assembly Part Number : 800-34284-03
Top Assembly Serial Number : FCZ1611W414
Top Revision Number : A0
Product/Model Number : AIR-LAP1041N-E-K9
% Please define a domain-name first.
Press RETURN to get started!
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:09.574: *** CRASH_LOG = YES
Base Ethernet MAC address: 44:2B:03:DC:09:25
*Mar 1 00:00:09.838: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log
(contains, 1024 messages)
*Mar 1 00:00:11.848: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:11.892: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
*Mar 1 00:08:16.954: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
logging facility kern
^
% Invalid input detected at '^' marker.
*Mar 1 00:08:28.047: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Mar 1 00:08:28.049: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:09:08.282: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASS
IC_NO_INJECTOR_CONFIGURED AIR-CT5508-K9 (c464.138f.9345)
*Mar 1 00:09:08.282: -Verify the required power-injector is installed on this
port: AIR-CT5508-K9(Gig 0/0/2).
*Mar 1 00:09:08.282: -If a power-injector is installed, issue the command:"pow
er inline negotiation injector installed"
*Mar 1 00:12:19.976: %CAPWAP-5-STATIC_TO_DHCP_IP: Could not discover WLC using
static IP. Forcing AP to use DHCP.
*Mar 1 00:12:29.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:39.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:49.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:59.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:09.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
Not in Bound state.
*Mar 1 00:13:19.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:19.993: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP
. Renewing DHCP IP.
logs from wireless controller:
(Cisco Controller) >show interface summary
Interface Name Port Vlan Id IP Address Type Ap Mgr Gu
est
ap-manager 2 untagged 209.165.200.231 Dynamic Yes No
management 1 untagged 209.165.200.230 Static Yes No
service-port N/A N/A 192.168.1.157 Static No No
virtual N/A N/A 1.1.1.1 Static No No
(Cisco Controller) >
i conect with service-port ok and the management port works, i think.
AP442b.03dc.0925>ping 209.165.200.230
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 209.165.200.230, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
AP442b.03dc.0925>
Help, please!
i write in spanish:
Hola:
Tengo que configurar un cisco 5508 wireless controller con 25 air-lap1041n, para usarlo como acceso de datos y voz. ¿Cómo lo hago? He leído manuales, y seguido las instrucciones, pero el punto de acceso parace que no es capaz de cargar el perfil. No hay servidor radius, solo la configuración de una clave wpa. Alguién me puede indicar pasos, GraciasHi!
I buy a gigabit switch. I connect the service-port to gigabit switch, and laptop to gigabit switch. I used 192.168.1.x ip address (192.168.1.157 to service-port and 192.168.1.233 to wired port on laptop, well, the laptop has two ip adress, 192.168.1.233 and 209.165.200.2, and the laptop works ok. Ping to 209.165.200.230 -ip address of management interface- and ping to 209.165.200.203 -ip address for AP, is assigned by DHCP of WLC. And i connect the ap to gigabit switch, and the wlc assigns well an ip direction.
I post the run-config and sysinfo log. The gigabit switch is tp-link model tl-sg1005d, no configuration.
Before the logs, I see this message from AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Hola:
He comprado un switch gigabit. Conecto el service-port al switch gigabit y el portátil también (por cable). Uso como direcciones ip el rango 192.168.1.x (192.168.1.157 asignado al service-port y 192, 168.1.233 al portátil, bueno, el portátil tiene dos direcciones, la dicha anteriormente y la 209.165.200.2) El portátil funciona bien, hace ping al 209.165.200.230 - la ip de la management interface, y a 209.165.200.203 - ip asignada al AP por el DHCP del WLC. He conectado el AP al swtich gigabit, y el dhcp del wlc asigna correctamente una dirección ip.
Añado a continuación los resultados de los comandos "show run-config" y "show sysinfo". El switch es un TP-LINK modelo TL-S1005D, sin necesidad de configuración.
Antes de mostrar los resultados de los comandos, he visto el siguiente mensaje en el log del AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Un saludo
Antonio R.
(Cisco Controller) >show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco Wireless Controller"
PID: AIR-CT5508-K9, VID: V02, SN: FCW1608L05X
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 17 mins 45 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Network Information
RF-Network Name............................. hosp
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Fast SSID Change ........................... Disabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or to abort
AP Summary
Number of APs.................................... 0
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Location
Site Name........................................ default-group
Site Description.................................
WLAN ID Interface Network Admission Control
1 management Disabled
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority GroupName
Press Enter to continue or to abort
AP Config
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Airewave Director Configuration
Press Enter to continue or to abort
802.11a Configuration
802.11a Network.................................. Disabled
11nSupport....................................... Enabled
802.11a Low Band........................... Enabled
802.11a Mid Band........................... Enabled
802.11a High Band.......................... Enabled
802.11a Operational Rates
802.11a 6M Rate.............................. Mandatory
802.11a 9M Rate.............................. Supported
802.11a 12M Rate............................. Mandatory
802.11a 18M Rate............................. Supported
802.11a 24M Rate............................. Mandatory
802.11a 36M Rate............................. Supported
802.11a 48M Rate............................. Supported
802.11a 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
MCS 5........................................ Supported
MCS 6........................................ Supported
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Disabled
Priority 5............................... Disabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mandatory............................ Disabled
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
CFP Maximum Duration............................. 60
Default Channel.................................. 36
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Fragmentation Threshold.......................... 2346
TI Threshold..................................... -50
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC:
Voice AC - Admission control (ACM)............ Disabled
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Video AC:
Video AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
Video max RF bandwidth........................ Infinite
Video reserved roaming bandwidth.............. 0
Press Enter to continue or to abort
802.11a Advanced Configuration
Press Enter to continue or to abort
802.11a Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
TxPower Update Logging......................... Off
Default 802.11a AP performance profiles
802.11a Global Interference threshold.......... 10 %
802.11a Global noise threshold................. -70 dBm
802.11a Global RF utilization threshold........ 80 %
802.11a Global throughput threshold............ 1000000 bps
802.11a Global clients threshold............... 12 clients
Default 802.11a AP monitoring
802.11a Monitor Mode........................... enable
802.11a Monitor Mode for Mesh AP Backhaul...... disable
802.11a Monitor Channels....................... Country channels
802.11a AP Coverage Interval................... 180 seconds
802.11a AP Load Interval....................... 60 seconds
802.11a AP Noise Interval...................... 180 seconds
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
802.11a AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
Coverage Hole Detection
802.11a Coverage Hole Detection Mode........... Enabled
802.11a Coverage Voice Packet Count............ 100 packets
802.11a Coverage Voice Packet Percentage....... 50%
802.11a Coverage Voice RSSI Threshold.......... -80 dBm
802.11a Coverage Data Packet Count............. 50 packets
802.11a Coverage Data Packet Percentage........ 50%
802.11a Coverage Data RSSI Threshold........... -80 dBm
802.11a Global coverage exception level........ 25 %
802.11a Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
--More or (q)uit current module or to abort
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
DCA Sensitivity Level.......................... STARTUP (5 dB)
DCA 802.11n Channel Width...................... 20 MHz
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11a 5 GHz Auto-RF Channel List
Allowed Channel List......................... 36,40,44,48,52,56,60,64
Unused Channel List.......................... 100,104,108,112,116,120,124,
128,132,136,140
DCA Outdoor AP option.......................... Disabled
Radio RF Grouping
802.11a Group Mode............................. AUTO
--More or (q)uit current module or to abort
802.11a Group Update Interval.................. 600 seconds
802.11a Group Leader........................... c4:64:13:8f:93:40
802.11a Group Member......................... c4:64:13:8f:93:40
802.11a Last Run............................... 75 seconds ago
802.11b Configuration
802.11b Network.................................. Enabled
11gSupport....................................... Enabled
11nSupport....................................... Enabled
802.11b/g Operational Rates
802.11b/g 1M Rate............................ Mandatory
802.11b/g 2M Rate............................ Mandatory
802.11b/g 5.5M Rate.......................... Mandatory
802.11b/g 11M Rate........................... Mandatory
802.11g 6M Rate.............................. Supported
802.11g 9M Rate.............................. Supported
802.11g 12M Rate............................. Supported
802.11g 18M Rate............................. Supported
802.11g 24M Rate............................. Supported
802.11g 36M Rate............................. Supported
802.11g 48M Rate............................. Supported
802.11g 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
--More or (q)uit current module or to abort
MCS 5........................................ Supported
MCS 6........................................ Supported
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Disabled
Priority 5............................... Disabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mode................................. Disabled
--More or (q)uit current module or to abort
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 1
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Call Admission Limit ........................... 105
G711 CU Quantum ................................. 15
ED Threshold..................................... -50
Fragmentation Threshold.......................... 2346
PBCC mandatory................................... Disabled
RTS Threshold.................................... 2347
Short Preamble mandatory......................... Enabled
Short Retry Limit................................ 7
Legacy Tx Beamforming setting.................... Enabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
Faster Carrier Tracking Loop..................... Disabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Video AC - Admission control (ACM)............ Disabled
Video max RF bandwidth........................ 50
Video reserved roaming bandwidth.............. 0
802.11b Advanced Configuration
Press Enter to continue or to abort
802.11b Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
Transmit Power Update Logging.................. Off
Default 802.11b AP performance profiles
802.11b Global Interference threshold.......... 10 %
802.11b Global noise threshold................. -70 dBm
802.11b Global RF utilization threshold........ 80 %
802.11b Global throughput threshold............ 1000000 bps
802.11b Global clients threshold............... 12 clients
Default 802.11b AP monitoring
802.11b Monitor Mode........................... enable
802.11b Monitor Channels....................... Country channels
802.11b AP Coverage Interval................... 180 seconds
802.11b AP Load Interval....................... 60 seconds
802.11b AP Noise Interval...................... 180 seconds
802.11b AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
Coverage Hole Detection
802.11b Coverage Hole Detection Mode........... Enabled
802.11b Coverage Voice Packet Count............ 100 packets
802.11b Coverage Voice Packet Percentage....... 50%
802.11b Coverage Voice RSSI Threshold.......... -80 dBm
802.11b Coverage Data Packet Count............. 50 packets
802.11b Coverage Data Packet Percentage........ 50%
802.11b Coverage Data RSSI Threshold........... -80 dBm
802.11b Global coverage exception level........ 25 %
802.11b Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
DCA Sensitivity Level: ...................... STARTUP (5 dB)
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11b Auto-RF Allowed Channel List........... 1,6,11
Auto-RF Unused Channel List.................... 2,3,4,5,7,8,9,10,12,13
Radio RF Grouping
802.11b Group Mode............................. AUTO
802.11b Group Update Interval.................. 600 seconds
802.11b Group Leader........................... c4:64:13:8f:93:40
802.11b Group Member......................... c4:64:13:8f:93:40
802.11b Last Run............................... 213 seconds ago
Mobility Configuration
Symmetric Mobility Tunneling (current) .......... Enabled
Symmetric Mobility Tunneling (after reboot) ..... Enabled
Mobility Protocol Port........................... 16666
Default Mobility Domain.......................... hosp
Multicast Mode .................................. Disabled
Mobility Domain ID for 802.11r................... 0x97e2
Mobility Keepalive Interval...................... 10
Mobility Keepalive Count......................... 3
Mobility Group Members Configured................ 1
Mobility Control Message DSCP Value.............. 0
Controllers configured in the Mobility Group
MAC Address IP Address Group Name Multicast
IP Status
c4:64:13:8f:93:40 209.165.200.230 hosp 0.0.0.0
Up
Advanced Configuration
Probe request filtering.......................... Enabled
Probes fwd to controller per client per radio.... 0
Probe request rate-limiting interval............. 500 msec
EAP-Identity-Request Timeout (seconds)........... 30
EAP-Identity-Request Max Retries................. 2
EAP Key-Index for Dynamic WEP.................... 0
EAP Max-Login Ignore Identity Response........... enable
EAP-Request Timeout (seconds).................... 30
EAP-Request Max Retries.......................... 2
EAPOL-Key Timeout (milliseconds)................. 1000
EAPOL-Key Max Retries............................ 2
dot11-padding.................................... Disabled
Authentication Response Timeout (seconds)........ 10
Rogue Entry Timeout (seconds).................... 1200
AP Heart Beat Timeout (seconds).................. 30
AP Discovery Timeout (seconds)................... 10
AP Local mode Fast Heartbeat (seconds)........... disable
AP Hreap mode Fast Heartbeat (seconds)........... disable
AP Primary Discovery Timeout (seconds)........... 120
AP Primed Join Timeout (seconds)................. 0
Packet Forwarding watchdog timer (seconds)....... 240 (enable)
Location Configuration
RFID Tag data Collection......................... Enabled
RFID timeout.................................... 1200 seconds
RFID mobility.................................... Oui:00:14:7e : Vendor:pango S
tate:Disabled
Interface Configuration
Interface Name................................... management
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 209.165.200.230
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 209.165.200.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 192.168.1.1
VLAN............................................. untagged
Quarantine-vlan.................................. 0
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. 209.165.200.230
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
Interface Name................................... service-port
MAC Address...................................... c4:64:13:8f:93:41
IP Address....................................... 192.168.1.157
IP Netmask....................................... 255.255.255.0
DHCP Option 82................................... Disabled
DHCP Protocol.................................... Disabled
AP Manager....................................... No
Guest Interface.................................. No
Interface Name................................... virtual
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 1.1.1.1
DHCP Option 82................................... Disabled
Virtual DNS Host Name............................ Disabled
AP Manager....................................... No
Guest Interface.................................. No
WLAN Configuration
WLAN Identifier.................................. 1
Profile Name..................................... HOSP3C
Network Name (SSID).............................. HOSP3C
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
NAC-State...................................... Disabled
Quarantine VLAN................................ 0
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
WLAN ACL......................................... unconfigured
DHCP Server...................................... 209.165.200.230
DHCP Address Assignment Required................. Enabled
Quality of Service............................... Platinum (voice)
Scan Defer Priority.............................. 5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
IPv6 Support..................................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... 802.11b and 802.11g only
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Disabled
Accounting.................................... Disabled
Dynamic Interface............................. Disabled
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Enabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Disabled
PSK..................................... Enabled
CCKM.................................... Disabled
FT(802.11r)............................. Disabled
FT-PSK(802.11r)......................... Disabled
FT Reassociation Timeout......................... 20
FT Over-The-Air mode............................. Enabled
FT Over-The-Ds mode.............................. Enabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
H-REAP Local Switching........................ Disabled
H-REAP Learn IP Address....................... Enabled
Infrastructure MFP protection................. Enabled
Client MFP.................................... Optional
Tkip MIC Countermeasure Hold-down Timer....... 60
Call Snooping.................................... Disabled
Band Select...................................... Enabled
Load Balancing................................... Enabled
Mobility Anchor List
WLAN ID IP Address Status
Press Enter to continue or to abort
Press Enter to continue or to abort
ACL Configuration
Press Enter to continue or to abort
CPU ACL Configuration
CPU Acl Name................................ NOT CONFIGURED
Wireless Traffic............................ Disabled
Wired Traffic............................... Disabled
RADIUS Configuration
Vendor Id Backward Compatibility................. Disabled
Call Station Id Case............................. lower
Call Station Id Type............................. IP Address
Aggressive Failover.............................. Enabled
Keywrap.......................................... Disabled
Fallback Test:
Test Mode.................................... Off
Probe User Name.............................. cisco-probe
Interval (in seconds)........................ 300
MAC Delimiter for Authentication Messages........ hyphen
MAC Delimiter for Accounting Messages............ hyphen
Authentication Servers
Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
Accounting Servers
Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
--More or (q)uit current module or to abort
TACACS Configuration
Authentication Servers
Idx Server Address Port State Tout
Authorization Servers
Idx Server Address Port State Tout
Accounting Servers
Idx Server Address Port State Tout
LDAP Configuration
Press Enter to continue or to abort
Local EAP Configuration
User credentials database search order:
Primary ..................................... Local DB
Timer:
Active timeout .............................. 300
Configured EAP profiles:
EAP Method configuration:
EAP-FAST:
Server key ................................
TTL for the PAC ........................... 10
Anonymous provision allowed ............... Yes
Authority ID .............................. 436973636f00000000000000000000
00
Authority Information ..................... Cisco A-ID
Press Enter to continue or to abort
HREAP Group Summary
HREAP Group Summary: Count: 0
Group Name # Aps
Press Enter to continue or to abort
HREAP Group Detail
Press Enter to continue or to abort
Route Info
Number of Routes................................. 0
Destination Network Netmask Gateway
Press Enter to continue or to abort
Qos Queue Length Info
Platinum queue length............................ 100
Gold queue length................................ 75
Silver queue length.............................. 50
Bronze queue length.............................. 25
Press Enter to continue or to abort
Mac Filter Info
Press Enter to continue or to abort
Authorization List
Authorize MIC APs against AAA ................... disabled
Authorize LSC APs against Auth-List ............. disabled
Allow APs with MIC - Manufactured Installed C.... disabled
Allow APs with SSC - Self-Signed Certificate..... disabled
Allow APs with LSC - Locally Significant Cert.... disabled
Load Balancing Info
Aggressive Load Balancing........................ Disabled
Aggressive Load Balancing Window................. 5 clients
Aggressive Load Balancing Denial Count........... 3
Statistics
Total Denied Count............................... 0 clients
Total Denial Sent................................ 0 messages
Exceeded Denial Max Limit Count.................. 0 times
None 5G Candidate Count.......................... 0 times
None 2.4G Candidate Count........................ 0 times
Press Enter to continue or to abort
Dhcp Scope Info
Scope: PUNTOSAP
Enabled.......................................... Yes
Lease Time....................................... 86400 (1 day )
Pool Start....................................... 209.165.200.201
Pool End......................................... 209.165.200.229
Network.......................................... 209.165.200.0
Netmask.......................................... 255.255.255.0
Default Routers.................................. 0.0.0.0 0.0.0.0 0.0.0.0
DNS Domain.......................................
DNS.............................................. 0.0.0.0 0.0.0.0 0.0.0.0
Netbios Name Servers............................. 0.0.0.0 0.0.0.0 0.0.0.0
Press Enter to continue or to abort
Exclusion List ConfigurationUnable to retrieve exclusion-list entry
Press Enter to continue or to abort
CDP Configuration
Press Enter to continue or to abort
Country Channels Configuration
Configured Country............................. ES - Spain
KEY: * = Channel is legal in this country and may be configured manually.
A = Channel is the Auto-RF default in this country.
. = Channel is not legal in this country.
C = Channel has been configured for use by Auto-RF.
x = Channel is available to be configured for use by Auto-RF.
(-,-) = (indoor, outdoor) regulatory doamin allowed by this country.
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11bg :
Channels : 1 1 1 1 1
: 1 2 3 4 5 6 7 8 9 0 1 2 3 4
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E ,-E ): A * * * * A * * * * A * * .
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11a : 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Channels : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6
: 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E ,-E ): . A . A . A . A A A A A * * * * * * * * * * * . . . . .
Press Enter to continue or to abort
WPS Configuration Summary
Auto-Immune
Auto-Immune.................................... Disabled
Client Exclusion Policy
Excessive 802.11-association failures.......... Enabled
Excessive 802.11-authentication failures....... Enabled
Excessive 802.1x-authentication................ Enabled
IP-theft....................................... Enabled
Excessive Web authentication failure........... Enabled
Signature Policy
Signature Processing........................... Enabled
Press Enter to continue or to abort
Custom Web Configuration
Radius Authentication Method..................... PAP
Cisco Logo....................................... Enabled
CustomLogo....................................... None
Custom Title..................................... None
Custom Message................................... None
Custom Redirect URL.............................. None
Web Authentication Type.......................... Internal Default
External Web Authentication URL.................. None
Configuration Per Profile:
Rogue AP Configuration
Rogue Location Discovery Protocol................ Disabled
Rogue on wire Auto-Contain....................... Disabled
Rogue using our SSID Auto-Contain................ Disabled
Valid client on rogue AP Auto-Contain............ Disabled
Rogue AP timeout................................. 1200
MAC Address Classification # APs # Clients Last Heard
Adhoc Rogue Configuration
Detect and report Ad-Hoc Networks................ Enabled
Auto-Contain Ad-Hoc Networks..................... Disabled
Client MAC Address Adhoc BSSID State # APs Last Heard
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
--More-- or (q)uit
MAC Address State # APs Last Heard
Ignore List Configuration
MAC Address
Rogue Rule Configuration
Priority Rule Name State Type Match Hit Count
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 41 mins 2 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +39 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
(Cisco Controller) >
The AP log
AP442b.03dc.0925>
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Selected MWAR 'CISCO-CAPWAP-CONTROLLER
'(index 0).
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Go join a capwap controller
logging facility kern
^
% Invalid input detected at '^' marker.
logging facility kern
^
% Invalid input detected at '^' marker.
*Apr 19 23:10:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:19.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Apr 19 23:10:20.200: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:20.201: %CAPWAP-5-SENDJOIN: sending Join Request to 209.165.200.23
0
*Apr 19 23:10:20.201: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
*Apr 19 23:10:20.354: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Apr 19 23:10:20.355: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 209
.165.200.230:5246
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.412: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
not established -
Guest wireless in 7.0.98 hitting the splash page
I have set up Guest wireless before with my own customized splash screen for local authentication on version 5.xx on a 4404 controller.
I have the same task again but this time with a 2201 controller and the latest ios.
Try as hard as I can i cannot get a guest wireless user to hit the splash page where it gives the certificate warning or past that to the login box.
Is there some subtle difference in the set up with 7.0.98. I did notice that when setting up the DHCP scope for the 7.0.98 i had to use the DHCP server IP as the managment interface. On my last try with 5.x I used the 192.168.80.1 address (the guest WLAN) So there is a difference right there.
Anyway the clients get an IP address so no issue there but i cannot get the cert warning up let alone the splash page. Eveidently there is a tick box I am missing. I wouldnt mide but having done this a few times before I am really stumped. I have wiped the config and started again going through my old notes step by step plus digging out the cisco documentation.
If there any debugging I can stick on please let me know.
Thanks,
NeilThank you :-) Hopefully I have captured everything you need.
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.06.27 09:22:56 =~=~=~=~=~=~=~=~=~=~=~=
(Cisco Controller) >show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco Wireless Controller"
PID: AIR-WLC2112-K9, VID: V05, SN: JMX1520Z02W
Burned-in MAC Address............................ 64:00:F1:91:76:40
Press Enter to continue or to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.98.0
RTOS Version..................................... 7.0.98.0
Bootloader Version............................... 4.0.191.0
Emergency Image Version.......................... 7.0.98.0
Build Type....................................... DATA + WPS
System Name...................................... GB-LON-WLC1
System Location.................................. London GHO
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.828
IP Address....................................... 10.y.y.22
System Up Time................................... 2 days 20 hrs 45 mins 31 secs
System Timezone Location.........................
Configured Country............................... GB - United Kingdom
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +48 C
--More or (q)uit current module or to abort
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 2
Number of Active Clients......................... 0
Burned-in MAC Address............................ 64:00:F1:91:76:40
Press Enter to continue or to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Press Enter to continue or to abort
Network Information
RF-Network Name............................. lon
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
Secure Shell (ssh).......................... Enable
Telnet...................................... Enable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Multicast Address : 239.0.1.1
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
--More or (q)uit current module or to abort
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Fast SSID Change ........................... Disabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE
1 Normal Forw Enable Auto 100 Full Up Enable N/A
2 Normal Disa Enable Auto Auto Down Enable N/A
3 Normal Disa Enable Auto Auto Down Enable N/A
4 Normal Disa Enable Auto Auto Down Enable N/A
5 Normal Disa Enable Auto Auto Down Enable N/A
6 Normal Disa Enable Auto Auto Down Enable N/A
7 Normal Disa Enable Auto Auto Down Enable Enable (Power Off)
8 Normal Disa Enable Auto Auto Down Enable Enable (Power Off)
Press Enter to continue or to abort
AP Summary
Number of APs.................................... 1
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
londonap1 2 AIR-LAP1131G-E-K9 00:21:d8:48:2b:96 London GHO 1 GB 1
Press Enter to continue or to abort
AP Location
Site Name........................................ GUEST
Site Description................................. GUEST - WebAuth - London
WLAN ID Interface Network Admission Control
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Site Name........................................ default-group
Site Description.................................
WLAN ID Interface Network Admission Control
1 london-vlan10 Disabled
2 london-guest Disabled
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
GB-LONdon 2 AIR-LAP1131G-E-K9 00:21:d8:48:2b:96 London GHO 1 GB 1
--More or (q)uit current module or to abort
Press Enter to continue or to abort
AP Config
Cisco AP Identifier.............................. 8
Cisco AP Name.................................... Gb-london
Country code..................................... GB - United Kingdom
Regulatory Domain allowed by Country............. 802.11bg:-E 802.11a:-E
AP Country code.................................. GB - United Kingdom
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:48:2b:96
IP Address Configuration......................... DHCP
IP Address....................................... 10.y.y.12
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.y.y.1
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Enabled
Ssh State........................................ Disabled
Cisco AP Location................................ London
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................ London
Primary Cisco Switch IP Address.................. 10.y.y.22
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or to abort
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.98.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131G-E-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA
--More or (q)uit current module or to abort
Reset Button..................................... Enabled
AP Serial Number................................. FCW1244V0FQ
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 2 days, 10 h 19 m 12 s
AP LWAPP Up Time................................. 0 days, 00 h 32 m 36 s
Join Date and Time............................... Mon Jun 27 07:50:18 2011
Join Taken Time.................................. 0 days, 00 h 00 m 31 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
--More or (q)uit current module or to abort
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:23:5e:4a:f9:b0
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ GB
--More or (q)uit current module or to abort
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 13
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 6
Tx Power Level 1 .......................... 14 dBm
Tx Power Level 2 .......................... 11 dBm
Tx Power Level 3 .......................... 8 dBm
Tx Power Level 4 .......................... 5 dBm
Tx Power Level 5 .......................... 2 dBm
Tx Power Level 6 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
--More or (q)uit current module or to abort
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11,12,
......................................... 13
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
--More or (q)uit current module or to abort
CleanAir Management Information
CleanAir Capable......................... No
AP does not have the 802.11a radio.
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Airewave Director Configuration
Number Of Slots.................................. 2
AP Name.......................................... londonap1
MAC Address...................................... 00:21:d8:48:2b:96
Slot ID........................................ 0
Radio Type..................................... RADIO_TYPE_80211b/g
Sub-band Type.................................. All
Noise Information
Noise Profile................................ PASSED
Channel 1.................................... -91 dBm
Channel 2.................................... -88 dBm
Channel 3.................................... -88 dBm
Channel 4.................................... -86 dBm
Channel 5.................................... -86 dBm
Channel 6.................................... -87 dBm
Channel 7.................................... -84 dBm
Channel 8.................................... -88 dBm
Channel 9.................................... -90 dBm
Channel 10................................... -85 dBm
Channel 11................................... -83 dBm
Channel 12................................... -89 dBm
Channel 13................................... -89 dBm
Interference Information
--More or (q)uit current module or to abort
Interference Profile......................... PASSED
Channel 1.................................... -63 dBm @ 1 % busy
Channel 2.................................... -128 dBm @ 0 % busy
Channel 3.................................... -63 dBm @ 2 % busy
Channel 4.................................... -46 dBm @ 8 % busy
Channel 5.................................... -44 dBm @ 2 % busy
Channel 6.................................... -64 dBm @ 1 % busy
Channel 7.................................... -46 dBm @ 4 % busy
Channel 8.................................... -128 dBm @ 0 % busy
Channel 9.................................... -70 dBm @ 4 % busy
Channel 10................................... -128 dBm @ 0 % busy
Channel 11................................... -65 dBm @ 14 % busy
Channel 12................................... -128 dBm @ 0 % busy
Channel 13................................... -128 dBm @ 0 % busy
Load Information
Load Profile................................. PASSED
Receive Utilization.......................... 0 %
Transmit Utilization......................... 9 %
Channel Utilization.......................... 14 %
Attached Clients............................. 0 clients
Coverage Information
Coverage Profile............................. PASSED
Failed Clients............................... 0 clients
--More or (q)uit current module or to abort
Client Signal Strengths
RSSI -100 dbm................................ 0 clients
RSSI -92 dbm................................ 0 clients
RSSI -84 dbm................................ 0 clients
RSSI -76 dbm................................ 0 clients
RSSI -68 dbm................................ 0 clients
RSSI -60 dbm................................ 0 clients
RSSI -52 dbm................................ 0 clients
Client Signal To Noise Ratios
SNR 0 dB.................................. 0 clients
SNR 5 dB.................................. 0 clients
SNR 10 dB.................................. 0 clients
SNR 15 dB.................................. 0 clients
SNR 20 dB.................................. 0 clients
SNR 25 dB.................................. 0 clients
SNR 30 dB.................................. 0 clients
SNR 35 dB.................................. 0 clients
SNR 40 dB.................................. 0 clients
SNR 45 dB.................................. 0 clients
Nearby APs
Radar Information
Channel Assignment Information
Current Channel Average Energy............... unknown
--More or (q)uit current module or to abort
Previous Channel Average Energy.............. unknown
Channel Change Count......................... 0
Last Channel Change Time..................... Mon Jun 27 07:50:15 2011
Recommended Best Channel..................... 1
RF Parameter Recommendations
Power Level.................................. 1
RTS/CTS Threshold............................ 2347
Fragmentation Tnreshold...................... 2346
Antenna Pattern.............................. 0
Persistent Interference Devices
Classtype Channel DC (%%) RSSI (dBm) Last Update Time
All third party trademarks are the property of their respective owners.
AP does not have the 802.11a radio.
Press Enter to continue or to abort
Press Enter to continue or to abort
802.11a Configuration
802.11a Network.................................. Enabled
11nSupport....................................... Enabled
802.11a Low Band........................... Enabled
802.11a Mid Band........................... Enabled
802.11a High Band.......................... Enabled
802.11a Operational Rates
802.11a 6M Rate.............................. Mandatory
802.11a 9M Rate.............................. Supported
802.11a 12M Rate............................. Mandatory
802.11a 18M Rate............................. Supported
802.11a 24M Rate............................. Mandatory
802.11a 36M Rate............................. Supported
802.11a 48M Rate............................. Supported
802.11a 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
MCS 5........................................ Supported
MCS 6........................................ Supported
--More or (q)uit current module or to abort
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Enabled
Priority 5............................... Enabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Guard Interval .............................. Any
Beacon Interval.................................. 100
CF Pollable mandatory............................ Disabled
CF Poll Request mandatory........................ Disabled
--More or (q)uit current module or to abort
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 36
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Fragmentation Threshold.......................... 2346
TI Threshold..................................... -50
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admission Control (CAC) configuration
Voice AC:
Voice AC - Admission control (ACM)............ Disabled
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Voice max limit on number of call............. 0
CAC SIP-Voice configuration
SIP Codec Type ............................... CODEC_TYPE_G711
--More or (q)uit current module or to abort
SIP call bandwidth ........................... 64
SIP call bandwith sample-size ................ 20
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Video AC:
Video AC - Admission control (ACM)............ Disabled
Video max RF bandwidth........................ Infinite
Video reserved roaming bandwidth.............. 0
Best-effort AC - Admission control (ACM)...... Disabled
Background AC - Admission control (ACM)....... Disabled
Press Enter to continue or to abort
802.11a Advanced Configuration
AP Name MAC Address Admin State Operation State Channel TxPower
Press Enter to continue or to abort
802.11a Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
TxPower Update Logging......................... Off
Default 802.11a AP performance profiles
802.11a Global Interference threshold.......... 10 %
802.11a Global noise threshold................. -70 dBm
802.11a Global RF utilization threshold........ 80 %
802.11a Global throughput threshold............ 1000000 bps
802.11a Global clients threshold............... 12 clients
Default 802.11a AP monitoring
802.11a Monitor Mode........................... enable
802.11a Monitor Mode for Mesh AP Backhaul...... disable
802.11a Monitor Channels....................... Country channels
802.11a AP Coverage Interval................... 180 seconds
802.11a AP Load Interval....................... 60 seconds
802.11a AP Noise Interval...................... 180 seconds
--More or (q)uit current module or to abort
802.11a AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -100 dBm
Max Transmit Power............................. 100 dBm
Transmit Power Update Contribution............. SNI..
Transmit Power Assignment Leader............... GB-LON-WLC1 (10.y.y.22)
Last Run....................................... 116 seconds ago
Coverage Hole Detection
802.11a Coverage Hole Detection Mode........... Enabled
802.11a Coverage Voice Packet Count............ 100 packets
802.11a Coverage Voice Packet Percentage....... 50%
802.11a Coverage Voice RSSI Threshold.......... -80 dBm
802.11a Coverage Data Packet Count............. 50 packets
802.11a Coverage Data Packet Percentage........ 50%
802.11a Coverage Data RSSI Threshold........... -80 dBm
802.11a Global coverage exception level........ 25 %
802.11a Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
--More or (q)uit current module or to abort
Channel Update Interval........................ 600 seconds
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI..
CleanAir Event-driven RRM option............... Disabled
CleanAir Event-driven RRM sensitivity.......... Medium
Channel Assignment Leader...................... GB-LON-WLC1 (10.y.y.22)
Last Run....................................... 116 seconds ago
DCA Sensitivity Level.......................... MEDIUM (15 dB)
DCA 802.11n Channel Width...................... 20 MHz
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11a 5 GHz Auto-RF Channel List
Allowed Channel List......................... 36,40,44,48,52,56,60,64
Unused Channel List.......................... 100,104,108,112,116,120,124,
128,132,136,140
DCA Outdoor AP option.......................... Disabled
--More or (q)uit current module or to abort
Radio RF Grouping
802.11a Group Mode............................. AUTO
802.11a Group Update Interval.................. 600 seconds
802.11a Group Leader........................... GB-LON-WLC1 (10.44.64.22)
802.11a Group Member......................... GB-LON-WLC1 (10.44.64.22)
802.11a Last Run............................... 116 seconds ago
802.11a CleanAir Configuration
Clean Air Solution............................... Disabled
Air Quality Settings:
Air Quality Reporting........................ Enabled
Air Quality Reporting Period (min)........... 15
Air Quality Alarms........................... Enabled
Air Quality Alarm Threshold.................. 35
Interference Device Settings:
Interference Device Reporting................ Enabled
Interference Device Types:
TDD Transmitter.......................... Enabled
Jammer................................... Enabled
Continuous Transmitter................... Enabled
DECT-like Phone.......................... Enabled
Video Camera............................. Enabled
WiFi Inverted............................ Enabled
--More or (q)uit current module or to abort
WiFi Invalid Channel..................... Enabled
SuperAG.................................. Enabled
Canopy................................... Enabled
WiMax Mobile............................. Enabled
WiMax Fixed.............................. Enabled
Interference Device Alarms................... Enabled
Interference Device Types Triggering Alarms:
TDD Transmitter.......................... Disabled
Jammer................................... Enabled
Continuous Transmitter................... Disabled
DECT-like Phone.......................... Disabled
Video Camera............................. Disabled
WiFi Inverted............................ Enabled
WiFi Invalid Channel..................... Enabled
SuperAG.................................. Disabled
Canopy................................... Disabled
WiMax Mobile............................. Disabled
WiMax Fixed.............................. Disabled
Additional Clean Air Settings:
CleanAir Event-driven RRM State.............. Disabled
CleanAir Driven RRM Sensitivity.............. Medium
CleanAir Persistent Devices state............ Disabled
--More or (q)uit current module or to abort
802.11a CleanAir AirQuality Summary
AQ = Air Quality
DFS = Dynamic Frequency Selection
AP Name Channel Avg AQ Min AQ Interferers DFS
Press Enter to continue or to abort
802.11b Configuration
802.11b Network.................................. Enabled
11gSupport....................................... Enabled
11nSupport....................................... Enabled
802.11b/g Operational Rates
802.11b/g 1M Rate............................ Mandatory
802.11b/g 2M Rate............................ Mandatory
802.11b/g 5.5M Rate.......................... Mandatory
802.11b/g 11M Rate........................... Mandatory
802.11g 6M Rate.............................. Supported
802.11g 9M Rate.............................. Supported
802.11g 12M Rate............................. Supported
802.11g 18M Rate............................. Supported
802.11g 24M Rate............................. Supported
802.11g 36M Rate............................. Supported
802.11g 48M Rate............................. Supported
802.11g 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
--More or (q)uit current module or to abort
MCS 5........................................ Supported
MCS 6........................................ Supported
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Enabled
Priority 5............................... Enabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Guard Interval .............................. Any
Beacon Interval.................................. 100
--More or (q)uit current module or to abort
CF Pollable mode................................. Disabled
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 1
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Call Admission Limit ........................... 105
G711 CU Quantum ................................. 15
ED Threshold..................................... -50
Fragmentation Threshold.......................... 2346
PBCC mandatory................................... Disabled
RTS Threshold.................................... 2347
Short Preamble mandatory......................... Enabled
Short Retry Limit................................ 7
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
Faster Carrier Tracking Loop..................... Disabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admission Control (CAC) configuration
--More or (q)uit current module or to abort
Voice AC - Admission control (ACM)............ Disabled
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Voice max limit on number of call............. 0
CAC SIP-Voice configuration
SIP Codec Type ............................... CODEC_TYPE_G711
SIP call bandwidth: .......................... 64
SIP call bandwidth sample-size ............... 20
Video AC - Admission control (ACM)............ Disabled
Video max RF bandwidth........................ 50
Video reserved roaming bandwidth.............. 0
Best-effort AC - Admission control (ACM)...... Disabled
Background AC - Admission control (ACM)....... Disabled
Press Enter to continue or to abort
802.11b Advanced Configuration
AP Name MAC Address Admin State Operation State Channel TxPower
londonap1 00:23:5e:4a:f9:b0 ENABLED UP 1* 1(*)
Press Enter to continue or to abort
802.11b Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
Transmit Power Update Logging.................. Off
Default 802.11b AP performance profiles
802.11b Global Interference threshold.......... 10 %
802.11b Global noise threshold................. -70 dBm
802.11b Global RF utilization threshold........ 80 %
802.11b Global throughput threshold............ 1000000 bps
802.11b Global clients threshold............... 12 clients
Default 802.11b AP monitoring
802.11b Monitor Mode........................... enable
802.11b Monitor Channels....................... Country channels
802.11b AP Coverage Interval................... 180 seconds
802.11b AP Load Interval....................... 60 seconds
802.11b AP Noise Interval...................... 180 seconds
802.11b AP Signal Strength Interval............ 60 seconds
--More or (q)uit current module or to abort
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -100 dBm
Max Transmit Power............................. 100 dBm
Transmit Power Update Contribution............. SNI..
Transmit Power Assignment Leader............... GB-LON-WLC1 (10.44.64.22)
Last Run....................................... 530 seconds ago
Coverage Hole Detection
802.11b Coverage Hole Detection Mode........... Enabled
802.11b Coverage Voice Packet Count............ 100 packets
802.11b Coverage Voice Packet Percentage....... 50%
802.11b Coverage Voice RSSI Threshold.......... -80 dBm
802.11b Coverage Data Packet Count............. 50 packets
802.11b Coverage Data Packet Percentage........ 50%
802.11b Coverage Data RSSI Threshold........... -80 dBm
802.11b Global coverage exception level........ 25 %
802.11b Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
Channel Update Interval........................ 600 seconds
--More or (q)uit current module or to abort
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI..
CleanAir Event-driven RRM option............... Disabled
CleanAir Event-driven RRM sensitivity.......... Medium
Channel Assignment Leader...................... GB-LON-WLC1 (10.44.64.22)
Last Run....................................... 530 seconds ago
DCA Sensitivity Level: ...................... MEDIUM (10 dB)
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... 0 days, 00 h 33 m 07 s
Average...................................... 0 days, 00 h 33 m 07 s
Maximum...................................... 0 days, 00 h 33 m 07 s
802.11b Auto-RF Allowed Channel List........... 1,6,11
Auto-RF Unused Channel List.................... 2,3,4,5,7,8,9,10,12,13
Radio RF Grouping
802.11b Group Mode............................. AUTO
802.11b Group Update Interval.................. 600 seconds
802.11b Group Leader........................... GB-LON-WLC1 (10.44.64.22)
--More or (q)uit current module or to abort
802.11b Group Member......................... GB-LON-WLC1 (10.44.64.22)
802.11b Last Run............................... 530 seconds ago
802.11a CleanAir Configuration
Clean Air Solution............................... Disabled
Air Quality Settings:
Air Quality Reporting........................ Enabled
Air Quality Reporting Period (min)........... 15
Air Quality Alarms........................... Enabled
Air Quality Alarm Threshold.................. 35
Interference Device Settings:
Interference Device Reporting................ Enabled
Interference Device Types:
Bluetooth Link........................... Enabled
Microwave Oven........................... Enabled
802.11 FH................................ Enabled
Bluetooth Discovery...................... Enabled
TDD Transmitter.......................... Enabled
Jammer................................... Enabled
Continuous Transmitter................... Enabled
DECT-like Phone.......................... Enabled
Video Camera............................. Enabled
802.15.4................................. Enabled
--More or (q)uit current module or to abort
WiFi Inverted............................ Enabled
WiFi Invalid Channel..................... Enabled
SuperAG.................................. Enabled
Canopy................................... Enabled
Xbox..................................... Enabled
WiMax Mobile............................. Enabled
WiMax Fixed.............................. Enabled
Interference Device Alarms................... Enabled
Interference Device Types Triggering Alarms:
Bluetooth Link........................... Disabled
Microwave Oven........................... Disabled
802.11 FH................................ Disabled
Bluetooth Discovery...................... Disabled
TDD Transmitter.......................... Disabled
Jammer................................... Enabled
Continuous Transmitter................... Disabled
DECT-like Phone.......................... Disabled
Video Camera............................. Disabled
802.15.4................................. Disabled
WiFi Inverted............................ Enabled
WiFi Invalid Channel..................... Enabled
SuperAG.................................. Disabled
Canopy................................... Disabled
--More or (q)uit current module or to abort
Xbox..................................... Disabled
WiMax Mobile............................. Disabled
WiMax Fixed.............................. Disabled
Additional Clean Air Settings:
CleanAir Event-driven RRM State.............. Disabled
CleanAir Driven RRM Sensitivity.............. Medium
CleanAir Persistent Devices state............ Disabled
802.11a CleanAir AirQuality Summary
AQ = Air Quality
DFS = Dynamic Frequency Selection
AP Name Channel Avg AQ Min AQ Interferers DFS
Press Enter to continue or to abort
q
Mobility Configuration
Symmetric Mobility Tunneling (current) .......... Enabled
Symmetric Mobility Tunneling (after reboot) ..... Enabled
Mobility Protocol Port........................... 16666
Default Mobility Domain.......................... lon
Multicast Mode .................................. Disabled
Mobility Domain ID for 802.11r................... 0x209c
Mobility Keepalive Interval...................... 10
Mobility Keepalive Count......................... 3
Mobility Group Members Configured................ 1
Mobility Control Message DSCP Value.............. 0
Controllers configured in the Mobility Group
MAC Address IP Address Group Name Multicast IP Status
64:00:f1:91:76:40 10.44.64.22 lon 0.0.0.0 Up
Press Enter to continue or to abort
Advanced Configuration
Probe request filtering.......................... Enabled
Probes fwd to controller per client per radio.... 2
Probe request rate-limiting interval............. 500 msec
Aggregate Probe request interval................. 500 msec
EAP-Identity-Request Timeout (seconds)........... 30
EAP-Identity-Request Max Retries................. 2
EAP Key-Index for Dynamic WEP.................... 0
EAP Max-Login Ignore Identity Response........... enable
EAP-Request Timeout (seconds).................... 30
EAP-Request Max Retries.......................... 2
EAPOL-Key Timeout (milliseconds)................. 1000
EAPOL-Key Max Retries............................ 2
dot11-padding.................................... Disabled
Press Enter to continue or to abort
Location Configuration
RFID Tag data Collection......................... Enabled
RFID timeout.................................... 1200 seconds
RFID mobility.................................... Oui:00:14:7e : Vendor:pango State:Disabled
Press Enter to continue or to abort
Interface Configuration
Interface Name................................... ap-manager
MAC Address...................................... 64:00:f1:91:76:40
IP Address....................................... 10.y.y.23
IP Netmask....................................... 255.255.254.0
IP Gateway....................................... 10.y.y.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. untagged
Physical Port.................................... 1
Primary DHCP Server.............................. 10.y.y.19
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
Interface Name................................... guest
MAC Address...................................... 64:00:f1:91:76:40
IP Address....................................... 192.168.x.1
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 192.168.x.2
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. 80
Quarantine-vlan.................................. 0
Physical Port.................................... 1
Primary DHCP Server.............................. Unconfigured
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... No
Guest Interface.................................. No
Interface Name................................... london-vlan10
MAC Address...................................... 64:00:f1:91:76:40
IP Address....................................... 10.x.x.149
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 10.x.x.20
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. 10
Quarantine-vlan.................................. 0
Physical Port.................................... 1
Primary DHCP Server.............................. 10.44.64.19
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... No
Guest Interface.................................. No
Interface Name................................... management
MAC Address...................................... 64:00:f1:91:76:40
IP Address....................................... 10.y.y.22
IP Netmask....................................... 255.255.254.0
IP Gateway....................................... 10.y.y.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. untagged
Quarantine-vlan.................................. 0
Physical Port.................................... 1
Primary DHCP Server.............................. 10.y.y.19
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... No
Guest Interface.................................. No
Interface Name................................... virtual
MAC Address...................................... 64:00:f1:91:76:40
IP Address....................................... 1.1.1.1
DHCP Option 82................................... Disabled
Virtual DNS Host Name............................ Disabled
AP Manager....................................... No
Guest Interface.................................. No
Press Enter to continue or to abort
WLAN Configuration
WLAN Identifier.................................. 1
Profile Name..................................... corporate
Network Name (SSID).............................. corporate
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
NAC-State...................................... Disabled
Quarantine VLAN................................ 0
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ london-vlan10
WLAN ACL......................................... unconfigured
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
--More or (q)uit current module or to abort
WLAN Configuration
WLAN Identifier.................................. 2
Profile Name..................................... Guest
Network Name (SSID).............................. GUEST
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
NAC-State...................................... Disabled
Quarantine VLAN................................ 0
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
CHD per WLAN..................................... Disabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ Guest-network
WLAN ACL......................................... unconfigured
DHCP Server...................................... 10.44.64.22
DHCP Address Assignment Required................. Enabled
--More or (q)uit current module or to abort
Quality of Service............................... Silver (best effort)
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
IPv6 Support..................................... Disabled
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Disabled
Accounting.................................... Disabled
Dynamic Interface............................. Disabled
Local EAP Authentication......................... Disabled
Security
--More or (q)uit current module or to abort
802.11 Authentication:........................ Open System
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Enabled
ACL............................................. Unconfigured
Web Authentication server precedence:
1............................................... local
2............................................... radius
3............................................... ldap
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
H-REAP Local Switching........................ Disabled
H-REAP Learn IP Address....................... Enabled
Client MFP.................................... Optional but inactive (WPA2 not configured)
Tkip MIC Countermeasure Hold-down Timer....... 60
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
--More or (q)uit current module or to abort
Mobility Anchor List
WLAN ID IP Address Status
Press Enter to continue or to abort
Press Enter to continue or to abort
ACL Configuration
Press Enter to continue or to abort
CPU ACL Configuration
CPU Acl Name................................ NOT CONFIGURED
Wireless Traffic............................ Disabled
Wired Traffic............................... Disabled
Press Enter to continue or to abort
RADIUS Configuration
Vendor Id Backward Compatibility................. Disabled
Call Station Id Case............................. lower
Call Station Id Type............................. IP Address
Aggressive Failover.............................. Enabled
Keywrap.......................................... Disabled
Fallback Test:
Test Mode.................................... Off
Probe User Name.............................. cisco-probe
Interval (in seconds)........................ 300
MAC Delimite -
1602i AP cannot connect to CT2504 Controller
Hi all,
I have a CT2504 with
Software Version
7.5.102.0
Field Recovery Image Version
System Name
Cisco_a5:d
I also have a 1602i AP with the software 15.2.4-JA1
The AP is trying to connect to the controller, but fails. I get the following log:
*Sep 25 16:58:33.035: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Sep 25 16:58:33.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.0.250 peer_port: 5246
*Sep 25 16:58:33.483: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.0.250 peer_port: 5246
*Sep 25 16:58:33.483: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.0.250
*Sep 25 16:58:33.483: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination
*Sep 25 16:58:33.483: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process m
essage type 10 state 5.
*Sep 25 16:58:33.483: %CAPWAP-3-ERRORLOG: Failed to handle capwap control messag
e from controller
*Sep 25 16:58:33.483: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap pac
ket from 192.168.0.250
*Sep 25 16:58:51.611: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceed
., 1)x(UNKNOWN_MESSAGE_TYPE (5)
*Sep 25 16:58:51.611: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Sep 25 16:58:51.611: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192
.168.0.250:5246
*Sep 25 16:58:51.655: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led sta
te 255
*Sep 25 16:58:51.675: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to a
dministratively down
*Sep 25 16:58:51.675: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to a
dministratively down
*Sep 25 16:58:51.687: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 25 16:58:51.727: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 25 16:58:52.675: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to down
*Sep 25 16:58:52.723: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to do
wn
*Sep 25 16:58:52.731: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to r
eset
*Sep 25 16:58:53.715: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to up
*Sep 25 16:58:53.723: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
1, changed state to down
*Sep 25 16:58:53.767: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 25 16:58:53.775: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to do
wn
*Sep 25 16:58:53.783: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to r
eset
*Sep 25 16:58:54.767: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
1, changed state to up
*Sep 25 16:58:54.775: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to down
*Sep 25 16:58:54.811: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 25 16:58:55.811: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to up
This repeats without success. Any help would be appreciated.I only have the second port connected to the switch. It is also the management port. I don't have a lot of info about the interfaces, so do not know if this is the best option. Run-config is as follows:
System Inventory
NAME: "Chassis" , DESCR: "Cisco 2500 Series Wireless LAN Controller"
PID: AIR-CT2504-K9, VID: V01, SN: PSZ172304B8
Burned-in MAC Address............................ 10:F3:11:A5:DD:20
Maximum number of APs supported.................. 5
Press Enter to continue or to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.5.102.0
Bootloader Version............................... 1.0.18
Field Recovery Image Version..................... 7.4.1.30
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... Cisco_a5:dd:24
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.0.250
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 42 mins 36 secs
System Timezone Location......................... (GMT +2:00) Jerusalem
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... TR - Turkey
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +31 C
External Temperature............................. +36 C
Fan Status....................................... 4200 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................ 10:F3:11:A5:DD:20
Maximum number of APs supported.................. 5
Redundancy Information
Redundancy Mode ................................. SSO DISABLED
Local State...................................... ACTIVE
Peer State....................................... N/A
Unit............................................. Primary
Unit ID.......................................... 10:F3:11:A5:DD:20
Redunadancy State................................ N/A
Mobility MAC..................................... 10:F3:11:A5:DD:20
Redundancy Management IP Address................. 0.0.0.0
Peer Redundancy Management IP Address............ 0.0.0.0
Redundancy Port IP Address....................... 0.0.0.0
Peer Redundancy Port IP Address.................. 169.254.0.0
AP Bundle Information
Primary AP Image Size
ap1g1 10776
ap1g2 10116
ap3g1 10156
ap3g2 11276
ap801 7444
ap802 8848
c1130 5092
c1140 10008
c1250 7184
c1520 8288
c602i 3756
Secondary AP Image Size
ap3g1 5792
ap801 5192
ap802 5232
c1100 3084
c1130 4964
c1140 4992
c1200 3364
c1240 4812
c1250 5504
c1310 3136
c1520 6404
c3201 4324
c602i 3716
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features
case-check.................................... Enabled
consecutive-check............................. Enabled
default-check................................. Enabled
username-check................................ Enabled
position-check................................ Disabled
case-digit-check.............................. Disabled
Min. Password length.......................... 3
Min. Upper case chars......................... 0
Min. Lower case chars......................... 0
Min. Digits chars............................. 0
Min. Special chars............................ 0
Mgmt User
Password Lifetime [days]...................... 0
Password Lockout.............................. Disabled
Lockout Attempts.............................. 0
Lockout Timeout [mins]........................ 0
SNMPv3 User
Password Lifetime [days]...................... 0
Password Lockout.............................. Disabled
Lockout Attempts.............................. 3
Lockout Timeout [mins]........................ 5
Network Information
RF-Network Name............................. cont
Web Mode.................................... Enable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Disable
Secure Web Mode RC4 Cipher Preference....... Disable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
IPv4 AP Multicast/Broadcast Mode............ Multicast Address : 0.0.0.0
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
MLD snooping................................ Disabled
MLD timeout................................. 60 seconds
MLD query interval.......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth CMCC Support ...................... Disabled
Web Auth Redirect Ports .................... 80,2
Web Auth Proxy Redirect ................... Disable
Web Auth Captive-Bypass .................. Disable
Web Auth Secure Web ....................... Enable
Fast SSID Change ........................... Disabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
CCX-lite status ............................ Disable
oeap-600 dual-rlan-ports ................... Disable
oeap-600 local-network ..................... Enable
oeap-600 Split Tunneling (Printers)......... Disable
WebPortal Online Client .................... 0
mDNS snooping............................... Disabled
mDNS Query Interval......................... 15 minutes
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE
1 Normal Disa Enable Auto Auto Down Enable N/A
2 Normal Forw Enable Auto 1000 Full Up Enable N/A
3 Normal Disa Enable Auto Auto Down Enable Enable (Power Off)
4 Normal Disa Enable Auto Auto Down Enable Enable (Power Off
AP Summary
Number of APs.................................... 0
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location
Country IP Address Clients
AP Tcp-Mss-Adjust Info
AP Name TCP State MSS Size
AP Location
Total Number of AP Groups........................ 0
Site Name........................................ default-group
Site Description.................................
NAS-identifier................................... Cisco_a5:dd:24
AP Operating Class............................... Not-configured
RF Profile
2.4 GHz band.....................................
5 GHz band.......................................
WLAN ID Interface Network Admission Control Radio Pol
icy
1 management Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority
RF Profile
Number of RF Profiles............................ 0
Out Of Box State................................. Disabled
RF Profile Name Band Description
11n-client-only Applied
802.11a Configuration
802.11a Network.................................. Enabled
11acSupport...................................... Enabled
11nSupport....................................... Enabled
802.11a Low Band........................... Enabled
802.11a Mid Band........................... Enabled
802.11a High Band.......................... Enabled
802.11a Operational Rates
802.11a 6M Rate.............................. Mandatory
802.11a 9M Rate.............................. Supported
802.11a 12M Rate............................. Mandatory
802.11a 18M Rate............................. Supported
802.11a 24M Rate............................. Mandatory
802.11a 36M Rate............................. Supported
802.11a 48M Rate............................. Supported
802.11a 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
MCS 5........................................ Supported
MCS 6........................................ Supported
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
MCS 16....................................... Supported
MCS 17....................................... Supported
MCS 18....................................... Supported
MCS 19....................................... Supported
MCS 20....................................... Supported
MCS 21....................................... Supported
MCS 22....................................... Supported
MCS 23....................................... Supported
802.11ac MCS Settings:
Nss=1: MCS 0-9 .............................. Supported
Nss=2: MCS 0-9 .............................. Supported
Nss=3: MCS 0-9 .............................. Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Enabled
Priority 5............................... Enabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Aggregation scheduler.................... Enabled
Frame Burst.............................. Automatic
Realtime Timeout..................... 10
A-MSDU Tx:
Priority 0............................... Enabled
Priority 1............................... Enabled
Priority 2............................... Enabled
Priority 3............................... Enabled
Priority 4............................... Enabled
Priority 5............................... Enabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Rifs Rx ..................................... Enabled
Guard Interval .............................. Any
Beacon Interval.................................. 100
CF Pollable mandatory............................ Disabled
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 36
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Fragmentation Threshold.......................... 2346
RSSI Low Check................................... Disabled
RSSI Threshold................................... -80
TI Threshold..................................... -50
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
dfs-peakdetect................................... Enabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admission Control (CAC) configuration
Voice AC:
Voice AC - Admission control (ACM)............ Disabled
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice CAC Method ............................. Load-Based
Voice tspec inactivity timeout................ Disabled
CAC SIP-Voice configuration
SIP based CAC ................................ Disabled
SIP Codec Type ............................... CODEC_TYPE_G711
SIP call bandwidth ........................... 64
SIP call bandwith sample-size ................ 20
Video AC:
Video AC - Admission control (ACM)............ Disabled
Video max RF bandwidth........................ Infinite
Video reserved roaming bandwidth.............. 0
Video load-based CAC mode..................... Disabled
Video CAC Method ............................. Static
CAC SIP-Video Configuration
SIP based CAC ................................ Disabled
Best-effort AC - Admission control (ACM)...... Disabled
Background AC - Admission control (ACM)....... Disabled
Maximum Number of Clients per AP Radio........... 200
802.11a Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
TxPower Update Logging......................... Off
Default 802.11a AP performance profiles
802.11a Global Interference threshold.......... 10 %
802.11a Global noise threshold................. -70 dBm
802.11a Global RF utilization threshold........ 80 %
802.11a Global throughput threshold............ 1000000 bps
802.11a Global clients threshold............... 12 clients
Default 802.11a AP monitoring
802.11a Monitor Mode........................... enable
802.11a Monitor Mode for Mesh AP Backhaul...... disable
802.11a Monitor Channels....................... Country channels
802.11a RRM Neighbor Discover Type............. Transparent
802.11a AP Coverage Interval................... 180 seconds
802.11a AP Load Interval....................... 60 seconds
802.11a AP Noise Interval...................... 180 seconds
802.11a AP Signal Strength Interval............ 60 seconds
802.11a AP Neighbor Report Interval............ 180 seconds
802.11a AP Interference Report Interval........ 120 seconds
Leader Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Update Contribution
Noise........................................ Enable
Interference................................. Enable
Load......................................... Disable
Device Aware................................. Disable
Transmit Power Assignment Leader............... Cisco_a5:dd:24 (192.168.0.250)
Last Run....................................... 361 seconds ago
Last Run Time.................................. 0 seconds
TPC Mode....................................... Version 1
TPCv2 Target RSSI.............................. -67 dBm
TPCv2 VoWLAN Guide RSSI........................ -67.0 dBm
TPCv2 SOP...................................... -85.0 dBm
TPCv2 Default Client Ant Gain.................. 0.0 dBi
TPCv2 Path Loss Decay Factor................... 3.6
TPCv2 Search Intensity......................... 10 Iterations
AP Name Channel TxPower Allowed Power Levels
Coverage Hole Detection
802.11a Coverage Hole Detection Mode........... Enabled
802.11a Coverage Voice Packet Count............ 100 packets
802.11a Coverage Voice Packet Percentage....... 50%
802.11a Coverage Voice RSSI Threshold.......... -80 dBm
802.11a Coverage Data Packet Count............. 50 packets
802.11a Coverage Data Packet Percentage........ 50%
802.11a Coverage Data RSSI Threshold........... -80 dBm
802.11a Global coverage exception level........ 25 %
802.11a Global client minimum exception lev.... 3 clients
Leader Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Update Contribution
Noise........................................ Enable
Noise........................................ Enable
Load......................................... Disable
Device Aware................................. Disable
CleanAir Event-driven RRM option............... Disabled
CleanAir Event-driven RRM sensitivity.......... Medium
Channel Assignment Leader...................... Cisco_a5:dd:24 (192.168.0.250)
Last Run....................................... 361 seconds ago
Last Run Time.................................. 0 seconds
DCA Sensitivity Level.......................... STARTUP (5 dB)
DCA 802.11n/ac Channel Width................... 20 MHz
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11a 5 GHz Auto-RF Channel List
Allowed Channel List......................... 36,40,44,48,52,56,60,64
Unused Channel List.......................... 100,104,108,112,116,120,124,
128,132,136,140
DCA Outdoor AP option.......................... Disabled
802.11a Radio RF Grouping
RF Group Name.................................. cont
RF Protocol Version(MIN)....................... 30(30)
RF Packet Header Version....................... 2
Group Role(Mode)............................... LEADER(AUTO)
Group State.................................... Idle
Group Update Interval.......................... 600 seconds
Group Leader................................... Cisco_a5:dd:24 (192.168.0.250)
Group Member
................................. Cisco_a5:dd:24 (192.168.0.250)
Maximum/Current number of Group Member......... 20/1
Maximum/Current number of AP................... 500/0
Last Run....................................... 361 seconds ago
802.11a CleanAir Configuration
Clean Air Solution............................... Disabled
Air Quality Settings:
Air Quality Reporting........................ Enabled
Air Quality Reporting Period (min)........... 15
Air Quality Alarms........................... Enabled
Air Quality Alarm Threshold................ 35
Unclassified Interference.................. Disabled
Unclassified Severity Threshold............ 20
Interference Device Settings:
Interference Device Reporting................ Enabled
Interference Device Types:
TDD Transmitter.......................... Enabled
Jammer................................... Enabled
Continuous Transmitter................... Enabled
DECT-like Phone.......................... Enabled
Video Camera............................. Enabled
WiFi Inverted............................ Enabled
WiFi Invalid Channel..................... Enabled
SuperAG.................................. Enabled
Canopy................................... Enabled
WiMax Mobile............................. Enabled
WiMax Fixed.............................. Enabled
Interference Device Alarms................... Enabled
Interference Device Types Triggering Alarms:
TDD Transmitter.......................... Disabled
Jammer................................... Enabled
Continuous Transmitter................... Disabled
DECT-like Phone.......................... Disabled
Video Camera............................. Disabled
WiFi Inverted............................ Enabled
WiFi Invalid Channel..................... Enabled
SuperAG.................................. Disabled
Canopy................................... Disabled
WiMax Mobile............................. Disabled
WiMax Fixed.............................. Disabled
Additional Clean Air Settings:
CleanAir ED-RRM State........................ Disabled
CleanAir ED-RRM Sensitivity.................. Medium
CleanAir ED-RRM Custom Threshold............. 50
CleanAir Persistent Devices state............ Disabled
CleanAir Persistent Device Propagation....... Disabled
802.11a CleanAir AirQuality Summary
AQ = Air Quality
DFS = Dynamic Frequency Selection
AP Name Channel Avg AQ Min AQ Interferers DFS
802.11b Configuration
802.11b Network.................................. Enabled
11gSupport....................................... Enabled
11nSupport....................................... Enabled
802.11b/g Operational Rates
802.11b/g 1M Rate............................ Mandatory
802.11b/g 2M Rate............................ Mandatory
802.11b/g 5.5M Rate.......................... Mandatory
802.11b/g 11M Rate........................... Mandatory
802.11g 6M Rate.............................. Supported
802.11g 9M Rate.............................. Supported
802.11g 12M Rate............................. Supported
802.11g 18M Rate............................. Supported
802.11g 24M Rate............................. Supported
802.11g 36M Rate............................. Supported
802.11g 48M Rate............................. Supported
802.11g 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
MCS 5........................................ Supported
MCS 6........................................ Supported
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
MCS 16....................................... Supported
MCS 17....................................... Supported
MCS 18....................................... Supported
MCS 19....................................... Supported
MCS 20....................................... Supported
MCS 21....................................... Supported
MCS 22....................................... Supported
MCS 23....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Enabled
Priority 5............................... Enabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Aggregation scheduler.................... Enabled
Realtime Timeout..................... 10
A-MSDU Tx:
Priority 0............................... Enabled
Priority 1............................... Enabled
Priority 2............................... Enabled
Priority 3............................... Enabled
Priority 4............................... Enabled
Priority 5............................... Enabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Rifs Rx ..................................... Enabled
Guard Interval .............................. Any
Beacon Interval.................................. 100
CF Pollable mode................................. Disabled
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 1
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
RSSI Low Check................................... Disabled
RSSI Threshold................................... -80
Call Admission Limit ........................... 105
G711 CU Quantum ................................. 15
ED Threshold..................................... -50
Fragmentation Threshold.......................... 2346
PBCC mandatory................................... Disabled
RTS Threshold.................................... 2347
Short Preamble mandatory......................... Enabled
Short Retry Limit................................ 7
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
Faster Carrier Tracking Loop..................... Disabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admission Control (CAC) configuration
Voice AC - Admission control (ACM)............ Disabled
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice CAC Method.............................. Load-Based
Voice tspec inactivity timeout................ Disabled
CAC SIP-Voice configuration
SIP based CAC ................................ Disabled
SIP Codec Type ............................... CODEC_TYPE_G711
SIP call bandwidth: .......................... 64
SIP call bandwidth sample-size ............... 20
Video AC - Admission control (ACM)............ Disabled
Video max RF bandwidth........................ Infinite
Video reserved roaming bandwidth.............. 0
Video load-based CAC mode..................... Disabled
Video CAC Method ............................. Static
CAC SIP-Video configuration
SIP based CAC ................................ Disabled
Best-effort AC - Admission control (ACM)...... Disabled
Background AC - Admission control (ACM)....... Disabled
Maximum Number of Clients per AP................. 200
802.11b Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
Transmit Power Update Logging.................. Off
Default 802.11b AP performance profiles
802.11b Global Interference threshold.......... 10 %
802.11b Global noise threshold................. -70 dBm
802.11b Global RF utilization threshold........ 80 %
802.11b Global throughput threshold............ 1000000 bps
802.11b Global clients threshold............... 12 clients
Default 802.11b AP monitoring
802.11b Monitor Mode........................... enable
802.11b Monitor Channels....................... Country channels
802.11b RRM Neighbor Discovery Type............ Transparent
802.11b AP Coverage Interval................... 180 seconds
802.11b AP Load Interval....................... 60 seconds
802.11b AP Noise Interval...................... 180 seconds
802.11b AP Signal Strength Interval............ 60 seconds
802.11b AP Neighbor Report Interval............ 180 seconds
802.11b AP Interference Report Interval........ 120 seconds
Leader Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Update Contribution
Noise........................................ Enable
Interference................................. Enable
Load......................................... Disable
Device Aware................................. Disable
Transmit Power Assignment Leader............... Cisco_a5:dd:24 (192.168.0.250)
Last Run....................................... 490 seconds ago
Last Run Time.................................. 0 seconds
TPC Mode....................................... Version 1
TPCv2 Target RSSI.............................. -67 dBm
TPCv2 VoWLAN Guide RSSI........................ -67.0 dBm
TPCv2 SOP...................................... -85.0 dBm
TPCv2 Default Client Ant Gain.................. 0.0 dBi
TPCv2 Path Loss Decay Factor................... 3.6
TPCv2 Search Intensity......................... 10 Iterations
AP Name Channel TxPower Allowed Power Levels
Coverage Hole Detection
802.11b Coverage Hole Detection Mode........... Enabled
802.11b Coverage Voice Packet Count............ 100 packets
802.11b Coverage Voice Packet Percentage....... 50%
802.11b Coverage Voice RSSI Threshold.......... -80 dBm
802.11b Coverage Data Packet Count............. 50 packets
802.11b Coverage Data Packet Percentage........ 50%
802.11b Coverage Data RSSI Threshold........... -80 dBm
802.11b Global coverage exception level........ 25 %
802.11b Global client minimum exception lev.... 3 clients
Leader Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Update Contribution
Noise........................................ Enable
Interference................................. Enable
Load......................................... Disable
Device Aware................................. Disable
CleanAir Event-driven RRM option............... Disabled
CleanAir Event-driven RRM sensitivity.......... Medium
Channel Assignment Leader...................... Cisco_a5:dd:24 (192.168.0.250)
Last Run....................................... 523 seconds ago
Last Run Time.................................. 0 seconds
DCA Sensitivity Level: ...................... STARTUP (5 dB)
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11b Auto-RF Allowed Channel List........... 1,5,9,13
Auto-RF Unused Channel List.................... 2,3,4,6,7,8,10,11,12
802.11b Radio RF Grouping
RF Group Name.................................. cont
RF Protocol Version(MIN)....................... 30(30)
RF Packet Header Version....................... 2
Group Role(Mode)............................... LEADER(AUTO)
Group State.................................... Idle
Group Update Interval.......................... 600 seconds
Group Leader................................... Cisco_a5:dd:24 (192.168.0.250)
Group Member
................................. Cisco_a5:dd:24 (192.168.0.250)
Maximum/Current number of Group Member......... 20/1
Maximum/Current number of AP................... 500/0
Last Run....................................... 523 seconds ago
802.11b CleanAir Configuration
Clean Air Solution............................... Disabled
Air Quality Settings:
Air Quality Reporting........................ Enabled
Air Quality Reporting Period (min)........... 15
Air Quality Alarms........................... Enabled
Air Quality Alarm Threshold................ 35
Unclassified Interference.................. Disabled
Unclassified Severity Threshold............ 20
Interference Device Settings:
Interference Device Reporting................ Enabled
Interference Device Types:
Bluetooth Link........................... Enabled
Microwave Oven........................... Enabled
802.11 FH................................ Enabled
Bluetooth Discovery...................... Enabled
TDD Transmitter.......................... Enabled
Jammer................................... Enabled
Continuous Transmitter................... Enabled
DECT-like Phone.......................... Enabled
Video Camera............................. Enabled
802.15.4................................. Enabled
WiFi Inverted............................ Enabled
WiFi Invalid Channel..................... Enabled
SuperAG.................................. Enabled
Canopy................................... Enabled
Microsoft Device......................... Enabled
WiMax Mobile............................. Enabled
WiMax Fixed.............................. Enabled
Interference Device Alarms................... Enabled
Interference Device Types Triggering Alarms:
Bluetooth Link........................... Disabled
Microwave Oven........................... Disabled
802.11 FH................................ Disabled
Bluetooth Discovery...................... Disabled
TDD Transmitter.......................... Disabled
Jammer................................... Enabled
Continuous Transmitter................... Disabled
DECT-like Phone.......................... Disabled
Video Camera............................. Disabled
802.15.4................................. Disabled
WiFi Inverted............................ Enabled
WiFi Invalid Channel..................... Enabled
SuperAG.................................. Disabled
Canopy................................... Disabled
Microsoft Device......................... Disabled
WiMax Mobile............................. Disabled
WiMax Fixed.............................. Disabled
Additional Clean Air Settings:
CleanAir ED-RRM State........................ Disabled
CleanAir ED-RRM Sensitivity.................. Medium
CleanAir ED-RRM Custom Threshold............. 50
CleanAir Persistent Devices state............ Disabled
CleanAir Persistent Device Propagation....... Disabled
802.11a CleanAir AirQuality Summary
AQ = Air Quality
DFS = Dynamic Frequency Selection
AP Name Channel Avg AQ Min AQ Interferers DFS
Mobility Configuration
Mobility Protocol Port........................... 16666
Default Mobility Domain.......................... cont
Multicast Mode .................................. Disabled
Mobility Domain ID for 802.11r................... 0xe3e
Mobility Keepalive Interval...................... 10
Mobility Keepalive Count......................... 3
Mobility Group Members Configured................ 1
Mobility Control Message DSCP Value.............. 0
Controllers configured in the Mobility Group
MAC Address IP Address Group Name
Multicast IP Status
10:f3:11:a5:dd:20 192.168.0.250 cont
0.0.0.0 Up
Mobility Hash Configuration
Default Mobility Domain.......................... cont
IP Address Hash Key
Self Signed Certificate details
SSC Hash validation.............................. Enabled.
SSC device certificate not present.
Mobility Foreign Map Configuration
WLAN ID Foreign Mac Address Interface
Advanced Configuration
Probe request filtering.......................... Enabled
Probes fwd to controller per client per radio.... 2
Probe request rate-limiting interval............. 500 msec
Aggregate Probe request interval................. 0 msec
Increased backoff parameters for probe respon.... Disabled
EAP-Identity-Request Timeout (seconds)........... 30
EAP-Identity-Request Max Retries................. 2
EAP Key-Index for Dynamic WEP.................... 0
EAP Max-Login Ignore Identity Response........... enable
EAP-Request Timeout (seconds).................... 30
EAP-Request Max Retries.......................... 2
EAPOL-Key Timeout (milliseconds)................. 1000
EAPOL-Key Max Retries............................ 2
EAP-Broadcast Key Interval....................... 3600
Fastpath Packet Capture.......................... disable
Fastpath Fast Cache Control...................... enable
Fastpath Fast Testmode........................... 0x0
dot11-padding.................................... Disabled
Advanced Hotspot Commands
ANQP 4-way state................................. Disabled
GARP Broadcast state: ........................... Enabled
GAS request rate limit .......................... Disabled
ANQP comeback delay in TUs(TU=1024usec).......... 50
Location Configuration
RFID Tag data Collection......................... Enabled
RFID timeout.................................... 1200 seconds
RFID mobility....................................
Interface Configuration
Interface Name................................... ap-management1
MAC Address...................................... 10:f3:11:a5:dd:24
IP Address....................................... 192.168.0.251
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 192.168.0.7
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. untagged
NAS-Identifier................................... Cisco_a5:dd:24
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
DHCP Proxy Mode.................................. Global
Primary DHCP Server.............................. 192.168.0.7
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
IPv4 ACL......................................... Unconfigured
IPv6 ACL......................................... Unconfigured
mDNS Profile Name................................ Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
L2 Multicast..................................... Enabled
Interface Name................................... ap-management3
MAC Address...................................... 10:f3:11:a5:dd:26
IP Address....................................... 192.168.0.253
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 192.168.0.7
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. untagged
NAS-Identifier................................... Cisco_a5:dd:24
Active Physical Port............................. 3
Primary Physical Port............................ 3
Backup Physical Port............................. Unconfigured
DHCP Proxy Mode.................................. Global
Primary DHCP Server.............................. 192.168.0.7
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
IPv4 ACL......................................... Unconfigured
IPv6 ACL......................................... Unconfigured
mDNS Profile Name................................ Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
L2 Multicast..................................... Enabled
Interface Name................................... ap-management4
MAC Address...................................... 10:f3:11:a5:dd:27
IP Address....................................... 192.168.0.254
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 192.168.0.7
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. untagged
NAS-Identifier................................... Cisco_a5:dd:24
Active Physical Port............................. 4
Primary Physical Port............................ 4
Backup Physical Port............................. Unconfigured
DHCP Proxy Mode.................................. Global
Primary DHCP Server.............................. 192.168.0.7
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
IPv4 ACL......................................... Unconfigured
IPv6 ACL......................................... Unconfigured
mDNS Profile Name................................ Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
L2 Multicast..................................... Enabled
Interface Name................................... management
MAC Address...................................... 10:f3:11:a5:dd:20
IP Address....................................... 192.168.0.250
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 192.168.0.7
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. untagged
Quarantine-vlan.................................. 0
Active Physical Port............................. 2
Primary Physical Port............................ 2
Backup Physical Port............................. Unconfigured
DHCP Proxy Mode.................................. Global
Primary DHCP Server.............................. 192.168.0.7
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
IPv4 ACL......................................... Unconfigured
IPv6 ACL......................................... Unconfigured
mDNS Profile Name................................ Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
L2 Multicast..................................... Disabled
Interface Name................................... virtual
MAC Address...................................... 10:f3:11:a5:dd:20
IP Address....................................... 1.1.1.1
Virtual DNS Host Name............................ Disabled
AP Manager....................................... No
Guest Interface.................................. No
Interface Group Configuration
WLAN Configuration
WLAN Identifier.................................. 1
Profile Name..................................... kisan
Network Name (SSID).............................. kisan
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
Client Profiling Status
Radius Profiling ............................ Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Local Profiling ............................. Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
User Idle Timeout................................ Disabled
Sleep Client..................................... disable
Sleep Client Timeout............................. 12 hours
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... Cisco_a5:dd:24
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
WLAN Layer2 ACL.................................. unconfigured
mDNS Status...................................... Enabled
mDNS Profile Name................................ default-mdns-profile
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Global Servers
Accounting.................................... Global Servers
Interim Update............................. Disabled
Framed IPv6 Acct AVP ...................... Prefix
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Disabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Enabled
PSK..................................... Disabled
CCKM.................................... Disabled
FT-1X(802.11r).......................... Disabled
FT-PSK(802.11r)......................... Disabled
PMF-1X(802.11w)......................... Disabled
PMF-PSK(802.11w)........................ Disabled
FT Reassociation Timeout................... 20
FT Over-The-DS mode........................ Enabled
GTK Randomization.......................... Disabled
SKC Cache Support.......................... Disabled
CCKM TSF Tolerance......................... 1000
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Disabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
flexconnect PPPoE pass-through................ Disabled
flexconnect local-switching IP-source-guar.... Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexCo -
MPLS TE Link Protection with FRR
Hi Sir,
Due to inconsistent result during my customer UAT TE link FRR. All the 3 PEs (C7609) link are connected in triangular (three different POPs). From PE-to-PE it's interconnected via DWDM devices. In this scenario, how can we know what type of mechanism is being used to detect GE link failure?
From my understanding, the router can issues thru' an IGP advertisement or an RSVP message.
Need to clarify with your expertise on ip rsvp configuration below, whether can use in our environment and to improve the link detection or not?
# ip rsvp signaling refresh interval ... (default 20ms; 10-30,000ms)
# ip rsvp signaling hello interface
# ip rsvp signaling refresh misses (default 4)
# ip rsvp signaling hello dcsp
If not, what is the alternative or leave it default with FRR configuration as below;
interface Tunnel1
description *** Primary TE Tunnel to SKBMPLS1GW ***
ip unnumbered Loopback0
tag-switching ip
tunnel destination 172.18.255.3
tunnel mode mpls traffic-eng
tunnel mpls traffic-eng autoroute announce
tunnel mpls traffic-eng priority 1 1
tunnel mpls traffic-eng path-option 1 explicit name path1_SKBMPLS1GW
tunnel mpls traffic-eng path-option 2 dynamic
tunnel mpls traffic-eng record-route
tunnel mpls traffic-eng fast-reroute
TQUse the RSVP timers for fast TE Tunnel re-optimization, that is when your existing tunnel fails, then doing a state timeout and signalling a fresh LSP on a different path to the tail end.
FRR will depend on the Link failure and the moment a link falure is detected it switches to the pre-configured backup tunnel, as it cannot wait till the Tunnel re-optimization happens as it has to provide the healing in sub 50ms. And the sub 50 ms value cannot be achieved relying only on Tunnel Re-Optimization. So RSVP is used to signal that the specific primary Tunnel requires protection in the RSVP path messages.
So you can keep you current FRR configuration to what it is right now, and changing the default RSVP timers wont help you to achieve or reduce the FRR healover times (close to 50ms).
The kickin of FRR would depend on the interface status when it goes down, which is dependent on LOS to be received from your DWDM device. And this will happen much faster than the RSVP hello misses.
HTH-Cheers,
Swaroop
For Reference:
http://www.cisco.com/en/US/products/ps6922/products_feature_guide09186a008027dbda.html -
Channel utilization - show ap auto-rf 802.11b
Question on the command "show ap auto-rf 802.11b <ap_name>". What is the period of time that is measured for:
Channel Utilization.......................... 64 %
I am seeing high channel util. on certain AP's, but standing directly below the AP w/ spectrum analyzer, I see much lower util.%:
Basically, wondering if the measurement is from the exact time I launch the command, or if it's over say a 10 sec. period?
WLCCA shows highest Rx neighbor @ -71
complete output of the command:
(WiSM-slot8-1) >show ap auto-rf 802.11b ap-bhs-400-2
Number Of Slots.................................. 2
AP Name.......................................... ap-bhs-400-2
MAC Address...................................... 50:57:a8:d6:7d:6d
Slot ID........................................ 0
Radio Type..................................... RADIO_TYPE_80211b/g
Sub-band Type.................................. All
Noise Information
Noise Profile................................ PASSED
Channel 1.................................... -88 dBm
Channel 2.................................... -89 dBm
Channel 3.................................... -91 dBm
Channel 4.................................... -94 dBm
Channel 5.................................... -93 dBm
Channel 6.................................... -93 dBm
Channel 7.................................... -90 dBm
Channel 8.................................... -87 dBm
Channel 9.................................... -94 dBm
Channel 10................................... -92 dBm
Channel 11................................... -92 dBm
Interference Information
Interference Profile......................... PASSED
Channel 1.................................... -128 dBm @ 0 % busy
Channel 2.................................... -128 dBm @ 0 % busy
Channel 3.................................... -128 dBm @ 0 % busy
Channel 4.................................... -128 dBm @ 0 % busy
Channel 5.................................... -128 dBm @ 0 % busy
Channel 6.................................... -128 dBm @ 0 % busy
Channel 7.................................... -128 dBm @ 0 % busy
Channel 8.................................... -128 dBm @ 0 % busy
Channel 9.................................... -128 dBm @ 0 % busy
Channel 10................................... -128 dBm @ 0 % busy
Channel 11................................... -128 dBm @ 0 % busy
Load Information
Load Profile................................. PASSED
Receive Utilization.......................... 0 %
Transmit Utilization......................... 1 %
Channel Utilization.......................... 65 %
Attached Clients............................. 0 clients
Coverage Information
Coverage Profile............................. PASSED
Failed Clients............................... 0 clients
Client Signal Strengths
RSSI -100 dbm................................ 0 clients
RSSI -92 dbm................................ 0 clients
RSSI -84 dbm................................ 0 clients
RSSI -76 dbm................................ 0 clients
RSSI -68 dbm................................ 0 clients
RSSI -60 dbm................................ 0 clients
RSSI -52 dbm................................ 0 clients
Client Signal To Noise Ratios
SNR 0 dB.................................. 0 clients
SNR 5 dB.................................. 0 clients
SNR 10 dB.................................. 0 clients
SNR 15 dB.................................. 0 clients
SNR 20 dB.................................. 0 clients
SNR 25 dB.................................. 0 clients
SNR 30 dB.................................. 0 clients
SNR 35 dB.................................. 0 clients
SNR 40 dB.................................. 0 clients
SNR 45 dB.................................. 0 clients
Nearby APs
AP 00:0f:90:5e:2a:d0 slot 0.................. -73 dBm on 11 (10.252.1.2)
AP 00:13:5f:56:e0:90 slot 0.................. -88 dBm on 11 (10.252.1.4)
AP 00:13:5f:57:00:70 slot 0.................. -79 dBm on 1 (10.252.1.4)
AP 00:16:9c:91:64:e0 slot 0.................. -43 dBm on 11 (10.252.1.2)
AP 00:17:0f:db:2e:70 slot 0.................. -87 dBm on 1 (10.252.1.2)
AP 00:17:df:35:43:90 slot 0.................. -90 dBm on 1 (10.252.1.10)
AP 00:21:d8:d5:a2:40 slot 0.................. -91 dBm on 1 (10.252.1.12)
AP 00:21:d8:d5:a8:90 slot 0.................. -91 dBm on 1 (10.252.1.12)
AP 00:21:d8:d5:a8:c0 slot 0.................. -91 dBm on 11 (10.252.1.12)
AP 00:21:d8:d5:ac:80 slot 0.................. -92 dBm on 1 (10.252.1.12)
AP a4:56:30:5d:b0:a0 slot 0.................. -89 dBm on 11 (10.252.1.12)
AP b4:e9:b0:b3:c8:70 slot 0.................. -91 dBm on 11 (10.252.1.18)
Radar Information
Channel Assignment Information
Current Channel Average Energy............... -76 dBm
Previous Channel Average Energy.............. -57 dBm
Channel Change Count......................... 3
Last Channel Change Time..................... Wed Jul 17 22:27:37 2013
Recommended Best Channel..................... 1
RF Parameter Recommendations
Power Level.................................. 1
RTS/CTS Threshold............................ 2347
Fragmentation Threshold...................... 2346
Antenna Pattern.............................. 0
Persistent Interference Devices
Class Type Channel DC (%%) RSSI (dBm) Last Update Time
All third party trademarks are the property of their respective owners.
These are lined down a hallway (about 50' from ea. other). Looks to me like they are set for too high Tx and crowding chan. 1. I'll figure out the reason for that.
show advanced 802.11b txpower:
ap-bhs-400-1 *1 *1/7 (22 dBm) [22/19/16/13/10/7/4/4]
ap-bhs-400-2 *1 *1/7 (22 dBm) [22/19/16/13/10/7/4/4]
ap-bhs-400-3 *11 *1/8 (23 dBm) [23/20/17/14/11/8/5/2]
ap-bhs-400-4 *1 *1/7 (22 dBm) [22/19/16/13/10/7/4/4]
ap-bhs-400-5 *11 *7/8 ( 5 dBm) [23/20/17/14/11/8/5/2]
ap-bhs-400-6 *1 *1/7 (22 dBm) [22/19/16/13/10/7/4/4]
ap-bhs-451-1 *6 *7/8 ( 5 dBm) [23/20/17/14/11/8/5/2]Cool thx. Guessing "Load Interval". Looks like 60 seconds is the answer. Including output here for others...
show advanced 802.11b monitor
Default 802.11b AP monitoring
802.11b Monitor Mode........................... enable
802.11b Monitor Channels....................... Country channels
802.11b RRM Neighbor Discovery Type............ Transparent
802.11b AP Coverage Interval................... 180 seconds
802.11b AP Load Interval....................... 60 seconds
802.11b AP Noise Interval...................... 180 seconds
802.11b AP Signal Strength Interval............ 60 seconds
802.11b AP Neighbor Report Interval............ 180 seconds
802.11b AP Interference Report Interval........ 120 seconds -
Two signals on two outputs with specific time interval
I cant manage with following:
Have NI-6251 card. Trying to sent two step-signals on two outputs with
specific time interval, say 1 to 10 ms with 1us accuracy.
How can I start?
Thanks!Hi Anonymous,
What do you mean by step-signals? Do you mean a signal that steps up the voltage over time, a step function signal that is zero until a certain time then goes to 1, or a pulse train?
In the meantime you can find examples for getting started in the NI Example Finder by selecting Help » Find Examples
When that opens you can limit the examples to ones that are compatible with your hardware. In the bottom left corner select your hardware and check the Limit results to hardware box.
Browse to Hardware Input and Output » DAQmx » Digital Generation or Generating Digital Pulses.
Best Regards,
Bryan H. -
Min/ Max interval data storage
OK, so what I am trying to do is scan 2 voltages at 3K, temporarily write that data to a file or buffer, read the min and max values, and log those to a file once per minute. I'm at the point where I can scan and display the data, but really don't know where to go next. Any thoughts or ideas would be much appreciated. Thanks
Attachments:
NI-6343-2CH VDC min-max.vi 45 KBYou only need a single loop. You can use the "elapsed time" express VI to signal when time has elapsed, and simply use a case structure to append the averages to the data before writing (in the false case just wire the current data across). You should also open the file before the loop, append inside the loop, and only close the file once the loop completes. You can use the min&max ptbypt VI to keep track of the min and max for each interval or just keep track of it using a shift register.
LabVIEW Champion . Do more with less code and in less time . -
New router WRT160N, but still same poor signal!!
Hi all,
Been having issues with my wireless signal being poor and/or intermitent. I won't pretend to be computer literate, but I asked a Techie friend about this, and he suggested that I but a new router with the "N" signal.
My desktop signal is fine, but i have 3 laptops, and can be 30 feet away and get a fair/poor signal. When I go into the bedroom, which is upstairs, and in the furthest distance away from the router, the signal gets even weaker.
My Techie tried everything to bump up the signal, trying all channels, and even moved the router around the room. No luck!!
My house isn't made of steel, so there is no logical explanation for this... is there?
Please help me, and remember...I'm not real swarthy with the computer jargon,
thanks very muchTry to change the Wireless Settings on your Router as mentioned below, i think it will improve the wireless signal strength on your computers.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
- Here select manual configuration...Wireless Network mode should be mixed...
- Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbors network...
- Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WPA, For Encryption, select TKIP...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone and remember the key.
NOTE : Passphrase should be more that 8 characters...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75,Change the Fragmentation Threshold to 2304,Change the RTS Threshold to 2304 and Click on Save Settings...
Now see if you can locate your Wireless Network and attempt to connect... -
Hi!
I have a continuous sample data acquistion VI created. I collected an ECG signal from electrodes connected to an ELVIS unit. Once I viewed my signal, I am curious to determine the heart rate. I need to know how I can find the R-R interval, as well as the time over than span, so I can roughly determine the heart rate, continuously. Each time a new ECG wave occurs, the heart rate should be modified automatically. Some algorithm is required.
Thanks!Hello bmeecg,
Welcome to the NI forums! If I understand your question correctly, you wish to calculate the instantaneous heart rate from your ECG (the inverse of your R-R interval). I would recommend using the Peak Detection vi (Functions Palette»Signal Processing»Signal Operation) to determine the location of the R wave (since it is the largest magnitude, you could set a threshold above your P and T waves so that it only picks up the R wave). The calculation for time is in the detailed help for the Peak Detection vi (Ctrl+H»Hover over the VI»Detailed Help).
I also found this forum which has a VI that reads an ECG and then does a lot of analysis. Maybe this would help you out as well.
And just FYI, the Counter/Timer forum is oriented toward our counter/timer boards (e.g. the PCI-6602), the Multifunction DAQ forum probably would have more of the type of people that could help with this issue.
However, please post back here if you have more questions about this.
Neal M.Applications Engineering National Instruments www.ni.com/support -
Generated Pulse waveform is distorted when I deliver the signal to the output port in the DAQmx
Problem: Generated Pulse waveform is distorted when I deliver the signal to the output port in the DAQmx.
Environment: Windows XP sp3 (32bit), Visual Studio 2010 sp1, NI-Measurement Studio 2010
Device: NI - DAQmx PCI 6251
Analog Input: 1.00MS/s multi-channel (aggregate)
Analog Output: 2 Channel 2.00MS/s
Reference Example: AO_ContGenVoltageWfm_IntClk / AI_ContAcqVoltageSamples_IntClk
Generated Pulse:
1) AO0 = Square Waveform /0-5V / 8KHz / 0.5㎲/sample / sample 50% Duty
2) AO1 = Square Waveform /0-5V / 8KHz / 0.5㎲/sample / (Reverse Image)
Description: I’d like to deliver the waveform stream satisfied with specified constraints to the 2 channel output port in the DAQmx. To verify accuracy of the generated waveform, I did an electrical wiring from the Analog output channel (2 channels) to the Analog Input channel (2 channels) in DAQmx. As a result of this experiment, I could get a result which has signal distortion. Since the waveform has to satisfy with both high frequency (8KHz) and very short moment interval time (△t = 0.5㎲/sample) between samples, I cannot handle some parameters of the function in the referenced VC++ example. Following formulas shows an approach to deliver the generate pulse waveform to output port satisfied with constraints.
Analog Output Channel
Frequency = 8,000 cycles/sec (constraint)
Sample per Buffer = 2,000,000 = 2*106 samples/buffer
Cycles per Buffer = 80,000 cycles/buffer
Sample per Channel = 1,000,000 = 1*106 samples/channel
Sample Rate = Frequency * (Sample per Buffer / Cycle per Buffer)
= 8,000 * (2*106 / 80,000) = 2*106 samples / sec
△t = 1 sec / 2*106 samples / sec
= 0.5 * 10-6 sec/sample (constraint)
Buffer Cycle = Sample Rate / Sample per Channel
= (2*106 samples / sec) / (1*106 samples/channel)
= 2 channel / sec
Analog Input Channel
Sample per Channel = 1,000,000 = 1*106 samples/channel
Sample Rate = 1 MS/s * (2 Channel) = 5 * 105 Samples / Sec
Program Code
AO_ContGenVoltageWfm_IntClk / AI_ContAcqVoltageSamples_IntClk (VC++ Example)
Result: The proposed approach was implemented in the experiment environment (VS2010, MStudio2010). As shown in Figure 1, we could get the unsatisfied result. Although I intended to make a ‘square’ pulse wave, the result looks like ‘trapezoid’ pulse wave (Figure.1). However, there is other result which was undertaken with different parameter condition. It looks like the square shape not the trapezoid shape.
Please let me know what the conditions make the problem of signal distortion. (AO0 = Green line / AO1 = Red line)
[Figure. 1] Frequency 8000 Hz / Cycle per Buffer = 8000 Result
[Figure. 2] Frequency 1000 Hz / Cycle per Buffer = 1000 Result
Questions: Please let me know following questions.
1) Is it possible to deliver the generated pulse wave satisfied with constraints (f= 8KHz), △t = 0.5㎲/sample) to the output port without distortion using PXI 6251?
(Is it possible to solve the problem, if I use the LabView or MAX?)
2) Are there some mistakes in the proposed approach? (H/W or S/W program)
3) What is the meaning of the Cycle per Buffer?, It could effect to the result?Hi Brett Burger,
Thanks for your reply. For your information, I have set the sampling rate as 10000 as for the sound format, I have set the bits per sample as 16 bit, the rate as 11025 and the sound quality as mono. I tried using your method by changing the sampling rate as 8K but still my program encounter the same problem.
I wish to also create a button that is able to generate a preformatted report that contains VI documentation, data the VI returns, and report properties, such as the author, company, and number of pages only when I click on the button. I have created this in my program, but I am not sure why is it not working. Can you help troubleshoot my program. Or do you have any samples to provide me. Hope to hear from you soon.
Many thanks.
Regards,
min
Attachments:
Heart Sounds1.vi 971 KB -
Hello,
I am using Analogue module PXI 6713 A[5] pin in PXI
chassis 1044, to generate a Glitch( amplitude 1.2V with a depth of 0.5V) on a DC signal. The glitch on the DC signal
through A[5] pin is achieved in the following way.
Method 1: (Please refer Glitch_2ms.JPG and VMON_Ramp.vi
files)
1) Start generating the DC signal from 1.2V.
2) Once it reaches the 1.2V start decreasing the voltages
in steps of 0.1V until it reaches 0.5V.
3) Once it reaches 0.5V start increasing the voltages in
steps of 0.1V until it reaches 1.2V.
Repeat steps 1 , 2 and 3 ...
This way I am able to achieve the glitch width of 2ms
with a decrease of 0.1V /interval. But I would like to achieve the glitch of
width 1us or 10us. I followed below steps to generate the minimum glitch width.
Method 2: (Please refer Glitch_180us.JPG and
VMON_Ramp_debug.vi files)
1) Start generating 1.2V DC signal.
2) Immediately generate 0.5V DC signal.
Repeat steps 1 and 2.
But the glitch width I could able to achieve is only
180us which doesn’t meet my requirement of 1us.
The Labview source code for both the
methods are attached.
Could you please give your inputs in order to achieve the
glitch width of 1us order.
Thanks.
Sincerely,
Srinath.
[email protected]
816 728 2134
281 274 2988.
Attachments:
2ms_180us.JPG 75 KB
VMON_Ramp.vi 30 KB
VMON_Ramp_debug.vi 26 KBI believe I understand what you're trying to do. You cards maximum sample speed for single channel analog output is 1MS/s. This means that 1/1MS/s = 0.000001s/S is the minimum interval between samples that you can write. This is precisely 1 microsecond minimum dt. As a result, trying to write a glitch at 1microsecond means that it will be instantaneous and not ramped (there is no room to ramp because it would have to happen in the interval between 2 samples). Also, are you trying to make the clitch 2microseconds wide (1 down and 1 up)? That is reasonable as you can have 1 sample of down time at .5V and the rest up at 1.2V. Otherwise you're working on too small of a time scale (.5 microseconds down and .5 up is too small of an interval for the maximum sample speed of the card).
Also, if you're trying to do regenerative output (meaning you load a set number of samples to the card), you're going to have to make sure that the FIFO size (which is somewhere around 16k samples) is big enough to give you the appropriate interval upon which you want to re-trigger the glitch. In the case of that cards FIFO size this is a very small (16ms) interval. Is that a small enough interval for retriggering? You can also do it in non-regenerative mode which would allow you more control, however you'll need to be very careful about underflow issues. See the example in labview about continuous non-regenerative internal clock analog generation for an example of how to do this (should be in Hardware Input and Output->DAQmx->Analog Generation). If your "configurable time period" is smaller than around 16ms, you'll want to do things nonregeneratively. There may be a way to do it with some sort of complex triggering system, but I don't think the card is going to be capable of that, I think non-regenerative software methods are the only way to accomplish it on a larger time interval.
You may also (if this seems to daunting) wish to be put in touch with an alliance member who might be able to help you get the code written. It will cost a little, but if this will take a sizable chunk of your time it may be worth it. -
Periodic signal loss on DCT700 digital adapter
Our kitchen TV is connected to the FiOS ONT via a basic digital adapter (Motorola DCT700/US). On some TV channels, the sound disappears and the picture freezes for up to a few seconds at regular intervals.
The problem affects only channels 11 through 25, as far as I can tell (I didn't try every single one!). It occurs at the top of every minute, at the instant when the on-screen clock display rolls over to the next minute. Sometimes the event lasts for only a second or so, in which case the sound resumes and the picture unfreezes after the interruption. If the signal loss persists for longer, I get a gray screen with a message that "the channel is having technical difficulties" before the program resumes. Either way, it's very annoying.
If I'm watching the same channel via the SD set-top box in the living room, or via either of the CableCards in the TiVo DVR, there is no interruption of sound or picture.
The DCT700 was installed and activated by the Verizon rep as part of my FiOS installation two weeks ago. I don't recall the problem showing up when he performed his final checkup before leaving, but it's possible we chose channels outside the range mentioned above and/or weren't watching the TV during the fairly short time interval during which the problem occurs.
I tried disconnecting the power adapter from the DCT700 for about a minute, but the problem was still present after the DCT700 restarted.DukeDog wrote:
I pulled the plug and re-plugged all 3 adapters and none of them show a channel number. Very odd. And none of the of the manuals even reference the problem to find out how to correct it.
Do you have any idea why I'm not getting channels like CNN? Am I supposed to be getting channels like CNN?
The "trick" of unplugging should resolve the channel display issue (it only shows up for a short period in the bottom left of the TV screen immediately after changing channels).
As Matcarl said, if you are not getting all the SD channels you are subscribed to you need to contact Verizon as the boxes have apparently not been provisioned correctly.
If a forum member gives an answer you like, give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem. -
LinkSys e3000: Poor wireless signal
Hi,
I have configured a new LinkSys e3000 as as wireless router in our house.
I have left the configuration as default (only secured it and turned on the DHCP server).
I have only turned on the 2,4 GHz network ( because the 5GH had an even shorter range).
Everything works and all my devices can connect to the router and access the internet.
However i find the singnal strenght of the router to be very poor.
Already in the next room it drops to 60%. And in some rooms on the 1st floor the signal drops completly.
This happens not even 20m away from the router in an ordinary "family house".
Is there a setting somewhere which could increase the signal strength ?
I noticed that the router has no antenna, can one be bought and attached so the signal increases ?
The firmware version is 1.0.02 and i found a newer ony on your web 1.0.03. Would it help to upgrade to it ?
Any onther ideas how to improve the signal strength ?
Thank you in advance
HynekThere are built in antennas for this router.
Connect the computer to the router and open the setup page of the router.
Go to the wireless tab and change the Wireless channel to 11. Save the settings.
Click on Advanced wireless settings sub tab. Change the Beacon interval to 75, RTS threshold to 2307 and fragmentation threshold to 2306. Save the settings.
See if that helps you.
You can also try to upgrade the firmware on your router.
Connect the computer with the Ethernet cable to the router. Download the latest firmware from Linksys website and save it on your computer. Open the setup page of the router. Click on Administration tab and go to Firmware upgrade sub tab. Browse the firmware file that you have already downloaded and upgrade it on your router.
After upgrading the firmware on the router, it is recommended that you should reset the router and reconfigure it. Press and hold the reset button on the router for 30 seconds. Release the reset button and wait for 10 seconds. Power cycle the router and reconfigure it. -
Re: WRT350N ----- Very poor Wireless signal strength from my router
I have a WRT350N router. I had it for a year now. In the begining the Wireless Signal strenth was good.
I used to get 4-5 bars in my bed room which is about 10 meters from the router.
Now I have my laptop sitting 1 feet away from the router and I get only 1 bar.
I upgraded my firmware. I rebooted my router a few times still no luck.
Current Firmware Version: v1.04.4 build 003 Jul. 14, 2008
Can any one tell me whats the problem. More importantly can some one help me resolve this problem.
Thanks
SunnyAs you upgraded the router's firmware,I would suggest you to reset the router for 30 seconds and reconfigure it from the scratch, as it is advisable to reset the router after upgrading the router's firmware.
On the router's setup page,Under Wireless tab..Give unique name in the Wireless Network Name (SSID). Change the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz... Under the Advance Wireless tab,change the Beacon Interval to 75 and click on save settings.... Now,check.
Maybe you are looking for
-
Client interface methods in application module editor get unselected
Hello everybody, I have a problem with my application module client interface. Every time I edit source of application module methods that are exposed as a client interface, they get unselected in application module editor (they are not exposed anymo
-
Network bridge problems linking wwan0 and eth0 [SOLVED]
Hi There, I have just got working a 3G modem which appears as device wwan0. I am trying to link this interface to my wired ethernet eth0. wwan0 seems to work fine with network manager, getting a IP address via dhcp works just fine and I can use the i
-
What is 'acceptable' disk space
Hello - I have already posted on FCP and DVDSP boards, because I am having a problem with programs running to a certain point, and it was suggested to me that my available disk space might be an issue. I have an iMac G5, Mac OS X (10.4.10), that came
-
How do I get an *older* version of Firefox (5?)
-
How do I iWork from DVD on my macbook air?
I just bought a new MacBook Air and I would like to install iWork 09. I have the Family Pack iWork DVD. Since I don't have a DVD drive, I tried to transfer the iWork folder from a back up of my old computer and it did not work. What is the easiest w