[SOLVED] Loosing Wireless Connection
I am constantly loosing my wireless connection while I am trying to download something, usually I don't reach 60 MB and it's gone.
I am also loosing my connection while browsing the internet for 2-3 hours.
In both cases it reconnects after 2 minutes ,sometimes more.
I still have my IP address during these 2 minutes.
I tried different connection methods : wifi-menu, netctl, NetworkManager , manually with wpa_supplicant and dhcpcd(or dhclient) but they all lead to loosing my connection after a time.
iwconfig
enp11s0 no wireless extensions.
wlp2s0 IEEE 802.11abgn ESSID:"FRITZ!Box Gastzugang"
Mode:Managed Frequency:2.412 GHz Access Point: AccesPointX
Bit Rate=52 Mb/s Tx-Power=19 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
Link Quality=40/70 Signal level=-70 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:1698 Invalid misc:454 Missed beacon:0
lo no wireless extensions.
ip addr show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
2: enp11s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000
link/ether XX:XX:XX:XX:XX brd ff:ff:ff:ff:ff:ff
3: wlp2s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether XX:XX:XX:XX:XX brd ff:ff:ff:ff:ff:ff
inet 192.168.179.32/24 brd 192.168.179.255 scope global wlp2s0
valid_lft forever preferred_lft forever
sudo journalctl -u NetworkManager.service
-- Reboot --
Mar 15 18:05:03 Alik NetworkManager[161]: <info> NetworkManager (version 0.9.8.8) is starting...
Mar 15 18:05:03 Alik NetworkManager[161]: <info> Read config file /etc/NetworkManager/NetworkManager.conf
Mar 15 18:05:03 Alik NetworkManager[161]: <info> WEXT support is enabled
Mar 15 18:05:09 Alik NetworkManager[161]: <info> Loaded plugin keyfile: (c) 2007 - 2010 Red Hat, Inc. To report bugs please use the NetworkManager mailing list.
Mar 15 18:05:09 Alik NetworkManager[161]: keyfile: parsing Auto FRITZ!Box Gastzugang ...
Mar 15 18:05:09 Alik NetworkManager[161]: keyfile: read connection 'Auto FRITZ!Box Gastzugang'
Mar 15 18:05:09 Alik NetworkManager[161]: <info> monitoring kernel firmware directory '/lib/firmware'.
Mar 15 18:05:09 Alik NetworkManager[161]: <info> rfkill2: found WiFi radio killswitch (at /sys/devices/pci0000:00/0000:00:1c.1/0000:02:00.0/bcma0:0/ieee80211/phy0/rfkill2) (dri
Mar 15 18:05:09 Alik NetworkManager[161]: <info> rfkill0: found WiFi radio killswitch (at /sys/devices/platform/dell-laptop/rfkill/rfkill0) (platform driver dell-laptop)
Mar 15 18:05:09 Alik NetworkManager[161]: <info> WiFi hardware radio set enabled
Mar 15 18:05:09 Alik systemd[1]: Started Network Manager.
Mar 15 18:05:09 Alik NetworkManager[161]: <info> WiFi enabled by radio killswitch; enabled by state file
Mar 15 18:05:09 Alik NetworkManager[161]: <info> WWAN enabled by radio killswitch; enabled by state file
Mar 15 18:05:09 Alik NetworkManager[161]: <info> WiMAX enabled by radio killswitch; enabled by state file
Mar 15 18:05:09 Alik NetworkManager[161]: <info> Networking is enabled by state file
Mar 15 18:05:09 Alik NetworkManager[161]: <info> (wlp2s0): using nl80211 for WiFi device control
Mar 15 18:05:09 Alik NetworkManager[161]: <info> (wlp2s0): driver supports Access Point (AP) mode
Mar 15 18:05:09 Alik NetworkManager[161]: <info> (wlp2s0): new 802.11 WiFi device (driver: 'brcmsmac' ifindex: 3)
Mar 15 18:05:09 Alik NetworkManager[161]: <info> (wlp2s0): exported as /org/freedesktop/NetworkManager/Devices/0
Mar 15 18:05:09 Alik NetworkManager[161]: <info> (wlp2s0): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2]
Mar 15 18:05:09 Alik NetworkManager[161]: <info> (wlp2s0): bringing up device.
Mar 15 18:05:09 Alik NetworkManager[161]: <info> (wlp2s0): preparing device.
Mar 15 18:05:09 Alik NetworkManager[161]: <info> (wlp2s0): deactivating device (reason 'managed') [2]
Mar 15 18:05:09 Alik NetworkManager[161]: <warn> failed to allocate link cache: (-26) Protocol mismatch
Mar 15 18:05:09 Alik NetworkManager[161]: <info> (enp11s0): carrier is OFF
Mar 15 18:05:09 Alik NetworkManager[161]: <info> (enp11s0): new Ethernet device (driver: 'tg3' ifindex: 2)
Mar 15 18:05:09 Alik NetworkManager[161]: <info> (enp11s0): exported as /org/freedesktop/NetworkManager/Devices/1
Mar 15 18:05:09 Alik NetworkManager[161]: <info> (enp11s0): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2]
Mar 15 18:05:09 Alik NetworkManager[161]: <info> (enp11s0): bringing up device.
Mar 15 18:05:10 Alik NetworkManager[161]: <info> (enp11s0): preparing device.
Mar 15 18:05:10 Alik NetworkManager[161]: <info> (enp11s0): deactivating device (reason 'managed') [2]
Mar 15 18:05:10 Alik NetworkManager[161]: <info> Added default wired connection 'Wired connection 1' for /sys/devices/pci0000:00/0000:00:1c.5/0000:0b:00.0/net/enp11s0
Mar 15 18:05:10 Alik NetworkManager[161]: <warn> /sys/devices/virtual/net/lo: couldn't determine device driver; ignoring...
Mar 15 18:05:10 Alik NetworkManager[161]: <warn> /sys/devices/virtual/net/lo: couldn't determine device driver; ignoring...
Mar 15 18:05:11 Alik NetworkManager[161]: <warn> Couldn't acquire object manager proxy: Error calling StartServiceByName for org.bluez: GDBus.Error:org.freedesktop.systemd1.Loa
Mar 15 18:05:11 Alik NetworkManager[161]: <info> wpa_supplicant started
Mar 15 18:05:11 Alik NetworkManager[161]: <info> (wlp2s0) supports 4 scan SSIDs
Mar 15 18:05:11 Alik NetworkManager[161]: <warn> Trying to remove a non-existant call id.
Mar 15 18:05:11 Alik NetworkManager[161]: <info> (wlp2s0): supplicant interface state: starting -> ready
Mar 15 18:05:11 Alik NetworkManager[161]: <info> (wlp2s0): device state change: unavailable -> disconnected (reason 'supplicant-available') [20 30 42]
Mar 15 18:05:11 Alik NetworkManager[161]: <info> (wlp2s0): supplicant interface state: ready -> disconnected
Mar 15 18:05:11 Alik NetworkManager[161]: <info> (wlp2s0) supports 4 scan SSIDs
Mar 15 18:05:14 Alik NetworkManager[161]: <info> Auto-activating connection 'Auto FRITZ!Box Gastzugang'.
Mar 15 18:05:14 Alik NetworkManager[161]: <info> Activation (wlp2s0) starting connection 'Auto FRITZ!Box Gastzugang'
Mar 15 18:05:14 Alik NetworkManager[161]: <info> (wlp2s0): device state change: disconnected -> prepare (reason 'none') [30 40 0]
Mar 15 18:05:14 Alik NetworkManager[161]: <info> NetworkManager state is now CONNECTING
Mar 15 18:05:14 Alik NetworkManager[161]: <info> Activation (wlp2s0) Stage 1 of 5 (Device Prepare) scheduled...
Mar 15 18:05:14 Alik NetworkManager[161]: <info> Activation (wlp2s0) Stage 1 of 5 (Device Prepare) started...
Mar 15 18:05:14 Alik NetworkManager[161]: <info> Activation (wlp2s0) Stage 2 of 5 (Device Configure) scheduled...
Mar 15 18:05:14 Alik NetworkManager[161]: <info> Activation (wlp2s0) Stage 1 of 5 (Device Prepare) complete.
Mar 15 18:05:14 Alik NetworkManager[161]: <info> Activation (wlp2s0) Stage 2 of 5 (Device Configure) starting...
Mar 15 18:05:14 Alik NetworkManager[161]: <info> (wlp2s0): device state change: prepare -> config (reason 'none') [40 50 0]
Mar 15 18:05:14 Alik NetworkManager[161]: <info> Activation (wlp2s0/wireless): connection 'Auto FRITZ!Box Gastzugang' has security, and secrets exist. No new secrets needed.
Mar 15 18:05:14 Alik NetworkManager[161]: <info> Config: added 'ssid' value 'FRITZ!Box Gastzugang'
Mar 15 18:05:14 Alik NetworkManager[161]: <info> Config: added 'scan_ssid' value '1'
Mar 15 18:05:14 Alik NetworkManager[161]: <info> Config: added 'key_mgmt' value 'WPA-PSK'
Mar 15 18:05:14 Alik NetworkManager[161]: <info> Config: added 'psk' value '<omitted>'
Mar 15 18:05:14 Alik NetworkManager[161]: <info> Activation (wlp2s0) Stage 2 of 5 (Device Configure) complete.
Mar 15 18:05:15 Alik NetworkManager[161]: <info> Config: set interface ap_scan to 1
Mar 15 18:05:15 Alik NetworkManager[161]: <info> (wlp2s0): supplicant interface state: disconnected -> inactive
Mar 15 18:05:15 Alik NetworkManager[161]: <info> (wlp2s0): supplicant interface state: inactive -> associating
Mar 15 18:05:15 Alik NetworkManager[161]: <info> (wlp2s0): supplicant interface state: associating -> associated
Mar 15 18:05:15 Alik NetworkManager[161]: <info> (wlp2s0): supplicant interface state: associated -> 4-way handshake
Mar 15 18:05:15 Alik NetworkManager[161]: <info> (wlp2s0): supplicant interface state: 4-way handshake -> completed
Mar 15 18:05:15 Alik NetworkManager[161]: <info> Activation (wlp2s0/wireless) Stage 2 of 5 (Device Configure) successful. Connected to wireless network 'FRITZ!Box Gastzugang'.
Mar 15 18:05:15 Alik NetworkManager[161]: <info> Activation (wlp2s0) Stage 3 of 5 (IP Configure Start) scheduled.
Mar 15 18:05:15 Alik NetworkManager[161]: <info> Activation (wlp2s0) Stage 3 of 5 (IP Configure Start) started...
Mar 15 18:05:15 Alik NetworkManager[161]: <info> (wlp2s0): device state change: config -> ip-config (reason 'none') [50 70 0]
Mar 15 18:05:15 Alik NetworkManager[161]: <info> Activation (wlp2s0) Beginning DHCPv4 transaction (timeout in 45 seconds)
Mar 15 18:05:15 Alik NetworkManager[161]: <info> dhclient started with pid 321
Mar 15 18:05:15 Alik NetworkManager[161]: <info> Activation (wlp2s0) Beginning IP6 addrconf.
Mar 15 18:05:15 Alik NetworkManager[161]: <info> Activation (wlp2s0) Stage 3 of 5 (IP Configure Start) complete.
Mar 15 18:05:15 Alik dhclient[321]: Internet Systems Consortium DHCP Client 4.3.0
Mar 15 18:05:15 Alik dhclient[321]: Copyright 2004-2014 Internet Systems Consortium.
Mar 15 18:05:15 Alik dhclient[321]: All rights reserved.
Mar 15 18:05:15 Alik dhclient[321]: For info, please visit https://www.isc.org/software/dhcp/
Mar 15 18:05:15 Alik dhclient[321]:
Mar 15 18:05:15 Alik NetworkManager[161]: <info> (wlp2s0): DHCPv4 state changed nbi -> preinit
Mar 15 18:05:15 Alik dhclient[321]: Listening on LPF/wlp2s0/XX:XX:XX:XX:XX
Mar 15 18:05:15 Alik dhclient[321]: Sending on LPF/wlp2s0/XX:XX:XX:XX:XX
Mar 15 18:05:15 Alik dhclient[321]: Sending on Socket/fallback
Mar 15 18:05:15 Alik dhclient[321]: DHCPDISCOVER on wlp2s0 to 255.255.255.255 port 67 interval 6
Mar 15 18:05:16 Alik dhclient[321]: DHCPREQUEST on wlp2s0 to 255.255.255.255 port 67
Mar 15 18:05:16 Alik dhclient[321]: DHCPOFFER from 192.168.179.1
Mar 15 18:05:16 Alik dhclient[321]: DHCPACK from 192.168.179.1
Mar 15 18:05:16 Alik dhclient[321]: bound to 192.168.179.32 -- renewal in 415231 seconds.
Mar 15 18:05:16 Alik NetworkManager[161]: <info> (wlp2s0): DHCPv4 state changed preinit -> bound
Mar 15 18:05:16 Alik NetworkManager[161]: <info> address 192.168.179.32
Mar 15 18:05:16 Alik NetworkManager[161]: <info> prefix 24 (255.255.255.0)
Mar 15 18:05:16 Alik NetworkManager[161]: <info> gateway 192.168.179.1
Mar 15 18:05:16 Alik NetworkManager[161]: <info> nameserver '192.168.179.1'
Mar 15 18:05:16 Alik NetworkManager[161]: <info> domain name 'fritz.box'
Mar 15 18:05:16 Alik NetworkManager[161]: <info> Activation (wlp2s0) Stage 5 of 5 (IPv4 Configure Commit) scheduled...
Mar 15 18:05:16 Alik NetworkManager[161]: <info> Activation (wlp2s0) Stage 5 of 5 (IPv4 Commit) started...
Mar 15 18:05:17 Alik NetworkManager[161]: <info> (wlp2s0): device state change: ip-config -> secondaries (reason 'none') [70 90 0]
Mar 15 18:05:17 Alik NetworkManager[161]: <info> Activation (wlp2s0) Stage 5 of 5 (IPv4 Commit) complete.
Mar 15 18:05:17 Alik NetworkManager[161]: <info> (wlp2s0): device state change: secondaries -> activated (reason 'none') [90 100 0]
Mar 15 18:05:17 Alik NetworkManager[161]: <info> NetworkManager state is now CONNECTED_GLOBAL
Mar 15 18:05:17 Alik NetworkManager[161]: <info> Policy set 'Auto FRITZ!Box Gastzugang' (wlp2s0) as default for IPv4 routing and DNS.
Mar 15 18:05:17 Alik NetworkManager[161]: <info> Writing DNS information to /usr/bin/resolvconf
Mar 15 18:05:18 Alik NetworkManager[161]: <info> Activation (wlp2s0) successful, device activated.
Mar 15 18:05:18 Alik NetworkManager[161]: <info> Activation (wlp2s0) Stage 3 of 5 (IP Configure Start) starting DHCPv6 as requested by IPv6 router...
Mar 15 18:05:18 Alik NetworkManager[161]: <info> Activation (wlp2s0) Beginning DHCPv6 transaction (timeout in 45 seconds)
Mar 15 18:05:18 Alik NetworkManager[161]: <info> dhclient started with pid 380
Mar 15 18:05:18 Alik dhclient[380]: Internet Systems Consortium DHCP Client 4.3.0
Mar 15 18:05:18 Alik dhclient[380]: Copyright 2004-2014 Internet Systems Consortium.
Mar 15 18:05:18 Alik dhclient[380]: All rights reserved.
Mar 15 18:05:18 Alik dhclient[380]: For info, please visit https://www.isc.org/software/dhcp/
Mar 15 18:05:18 Alik dhclient[380]:
Mar 15 18:05:18 Alik dhclient[380]: Listening on Socket/wlp2s0
Mar 15 18:05:18 Alik dhclient[380]: Sending on Socket/wlp2s0
Mar 15 18:05:19 Alik dhclient[380]: XMT: Info-Request on wlp2s0, interval 1060ms.
Mar 15 18:05:20 Alik dhclient[380]: XMT: Info-Request on wlp2s0, interval 2120ms.
Mar 15 18:05:22 Alik dhclient[380]: XMT: Info-Request on wlp2s0, interval 4380ms.
Mar 15 18:05:26 Alik dhclient[380]: XMT: Info-Request on wlp2s0, interval 9150ms.
Mar 15 18:05:35 Alik dhclient[380]: XMT: Info-Request on wlp2s0, interval 18730ms.
Mar 15 18:05:54 Alik dhclient[380]: XMT: Info-Request on wlp2s0, interval 36040ms.
Mar 15 18:06:03 Alik NetworkManager[161]: <warn> (wlp2s0): DHCPv6 request timed out.
Mar 15 18:06:03 Alik NetworkManager[161]: <info> (wlp2s0): canceled DHCP transaction, DHCP client pid 380
Mar 15 18:06:03 Alik NetworkManager[161]: <info> Activation (wlp2s0) Stage 4 of 5 (IPv6 Configure Timeout) scheduled...
Mar 15 18:06:03 Alik NetworkManager[161]: <info> Activation (wlp2s0) Stage 4 of 5 (IPv6 Configure Timeout) started...
Mar 15 18:06:03 Alik NetworkManager[161]: <info> Activation (wlp2s0) Stage 4 of 5 (IPv6 Configure Timeout) complete.
Mar 15 18:11:47 Alik NetworkManager[161]: <warn> Connection disconnected (reason 2)
Mar 15 18:11:47 Alik NetworkManager[161]: <info> (wlp2s0): supplicant interface state: completed -> disconnected
Mar 15 18:11:47 Alik NetworkManager[161]: <info> (wlp2s0): supplicant interface state: disconnected -> scanning
Mar 15 18:11:51 Alik NetworkManager[161]: <info> (wlp2s0): supplicant interface state: scanning -> authenticating
Mar 15 18:11:51 Alik NetworkManager[161]: <info> (wlp2s0): supplicant interface state: authenticating -> associating
Mar 15 18:11:51 Alik NetworkManager[161]: <info> (wlp2s0): supplicant interface state: associating -> associated
Mar 15 18:11:51 Alik NetworkManager[161]: <info> (wlp2s0): supplicant interface state: associated -> 4-way handshake
Mar 15 18:11:51 Alik NetworkManager[161]: <info> (wlp2s0): supplicant interface state: 4-way handshake -> completed
Not surprisingly , everything works fine on Windows.
Thanks for the help
Last edited by ollen (2014-03-16 00:25:44)
first of all I stopped my NetworkManager.service and then :
sudo wpa_supplicant -Dnl80211 -iwlp2s0 -c/etc/wpa_supplicant/wpa_supplicant.conf &
Successfully initialized wpa_supplicant
wlp2s0: CTRL-EVENT-SCAN-STARTED
wlp2s0: SME: Trying to authenticate with XX:XX:XX:XX:XX (SSID='FRITZ!Box Gastzugang' freq=2412 MHz)
wlp2s0: Trying to associate with XX:XX:XX:XX:XX (SSID='FRITZ!Box Gastzugang' freq=2412 MHz)
wlp2s0: Associated with XX:XX:XX:XX:XX
wlp2s0: WPA: Key negotiation completed with XX:XX:XX:XX:XX [PTK=CCMP GTK=TKIP]
wlp2s0: CTRL-EVENT-CONNECTED - Connection to XX:XX:XX:XX:XX completed [id=0 id_str=]
and then I run
dhclient wlp2s0
but no output after this command but I get my IP address
I also ran this command
dhcpcd wlp2s0
and the output is
dhcpcd[2163]: version 6.3.1 starting
dhcpcd[2163]: DUID XX:
dhcpcd[2163]: wlp2s0: IAID XXX
dhcpcd[2163]: wlp2s0: soliciting an IPv6 router
dhcpcd[2163]: wlp2s0: rebinding lease of 192.168.179.32
dhcpcd[2163]: wlp2s0: leased 192.168.179.32 for 864000 seconds
dhcpcd[2163]: wlp2s0: adding route to 192.168.179.0/24
dhcpcd[2163]: wlp2s0: adding default route via 192.168.179.1
dhcpcd[2163]: forked to background, child pid 2558
a little bit of
journalctl -u wpa_supplicant.service
-- Reboot --
Mar 15 18:05:09 Alik systemd[1]: Starting WPA supplicant...
Mar 15 18:05:11 Alik systemd[1]: Started WPA supplicant.
Mar 15 19:53:19 Alik wpa_supplicant[289]: Successfully initialized wpa_supplicant
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: Reject scan trigger since one is already pending
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: SME: Trying to authenticate with XX:XX:XX:XX:XX (SSID='FRITZ!Box Gastzugang' freq=2412 MHz)
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: Trying to associate with XX:XX:XX:XX:XX (SSID='FRITZ!Box Gastzugang' freq=2412 MHz)
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: Associated with XX:XX:XX:XX:XX
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: WPA: Key negotiation completed with XX:XX:XX:XX:XX [PTK=CCMP GTK=TKIP]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-CONNECTED - Connection to XX:XX:XX:XX:XX completed [id=0 id_str=]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: WPA: Group rekeying completed with XX:XX:XX:XX:XX [GTK=TKIP]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: WPA: Group rekeying completed with XX:XX:XX:XX:XX [GTK=TKIP]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: WPA: Group rekeying completed with XX:XX:XX:XX:XX [GTK=TKIP]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: WPA: Group rekeying completed with XX:XX:XX:XX:XX [GTK=TKIP]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: WPA: Group rekeying completed with XX:XX:XX:XX:XX [GTK=TKIP]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: WPA: Group rekeying completed with XX:XX:XX:XX:XX [GTK=TKIP]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: WPA: Group rekeying completed with XX:XX:XX:XX:XX [GTK=TKIP]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-DISCONNECTED bssid=XX:XX:XX:XX:XX reason=2
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: SME: Trying to authenticate with XX:XX:XX:XX:XX (SSID='FRITZ!Box Gastzugang' freq=2412 MHz)
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: Trying to associate with XX:XX:XX:XX:XX (SSID='FRITZ!Box Gastzugang' freq=2412 MHz)
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: Associated with XX:XX:XX:XX:XX
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: WPA: Key negotiation completed with XX:XX:XX:XX:XX [PTK=CCMP GTK=TKIP]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-CONNECTED - Connection to XX:XX:XX:XX:XX completed [id=0 id_str=]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: WPA: Group rekeying completed with XX:XX:XX:XX:XX [GTK=TKIP]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: WPA: Group rekeying completed with XX:XX:XX:XX:XX [GTK=TKIP]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: WPA: Group rekeying completed with XX:XX:XX:XX:XX [GTK=TKIP]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: WPA: Group rekeying completed with XX:XX:XX:XX:XX [GTK=TKIP]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: WPA: Group rekeying completed with XX:XX:XX:XX:XX [GTK=TKIP]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: WPA: Group rekeying completed with XX:XX:XX:XX:XX [GTK=TKIP]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: WPA: Group rekeying completed with XX:XX:XX:XX:XX [GTK=TKIP]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: WPA: Group rekeying completed with XX:XX:XX:XX:XX [GTK=TKIP]
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: WPA: Group rekeying completed with XX:XX:XX:XX:XX [GTK=TKIP]
Mar 15 19:53:19 Alik wpa_supplicant[289]: rfkill: WLAN hard blocked
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-DISCONNECTED bssid=XX:XX:XX:XX:XX reason=3 locally_generated=1
Mar 15 19:53:19 Alik wpa_supplicant[289]: rfkill: WLAN hard blocked
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: Reject scan trigger since one is already pending
Mar 15 19:53:19 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:54:39 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:54:39 Alik wpa_supplicant[289]: wlp2s0: SME: Trying to authenticate with XX:XX:XX:XX:XX (SSID='FRITZ!Box Gastzugang' freq=2412 MHz)
Mar 15 19:54:39 Alik wpa_supplicant[289]: wlp2s0: SME: Authentication request to the driver failed
Mar 15 19:54:39 Alik wpa_supplicant[289]: wlp2s0: No network configuration found for the current AP
Mar 15 19:54:39 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-DISCONNECTED bssid=XX:XX:XX:XX:XX reason=3 locally_generated=1
Mar 15 19:54:39 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:54:39 Alik wpa_supplicant[289]: wlp2s0: SME: Trying to authenticate with XX:XX:XX:XX:XX (SSID='FRITZ!Box Gastzugang' freq=2412 MHz)
Mar 15 19:54:39 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:54:39 Alik wpa_supplicant[289]: wlp2s0: Trying to associate with XX:XX:XX:XX:XX (SSID='FRITZ!Box Gastzugang' freq=2412 MHz)
Mar 15 19:54:39 Alik wpa_supplicant[289]: wlp2s0: Associated with XX:XX:XX:XX:XX
Mar 15 19:54:39 Alik wpa_supplicant[289]: wlp2s0: WPA: Invalid EAPOL-Key MIC when using TPTK - ignoring TPTK
Mar 15 19:54:39 Alik wpa_supplicant[289]: wlp2s0: WPA: Could not verify EAPOL-Key MIC - dropping packet
Mar 15 19:54:39 Alik wpa_supplicant[289]: wlp2s0: Authentication with XX:XX:XX:XX:XX timed out.
Mar 15 19:54:39 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-DISCONNECTED bssid=XX:XX:XX:XX:XX reason=3 locally_generated=1
Mar 15 19:54:39 Alik wpa_supplicant[289]: wlp2s0: WPA: 4-Way Handshake failed - pre-shared key may be incorrect
Mar 15 19:54:39 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="FRITZ!Box Gastzugang" auth_failures=1 duration=10
Mar 15 19:54:40 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="FRITZ!Box Gastzugang" auth_failures=2 duration=20
Mar 15 19:54:40 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:54:40 Alik wpa_supplicant[289]: wlp2s0: Reject scan trigger since one is already pending
Mar 15 19:54:40 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Mar 15 19:54:40 Alik wpa_supplicant[289]: wlp2s0: No network configuration found for the current AP
Mar 15 19:54:40 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-DISCONNECTED bssid=XX:XX:XX:XX:XX reason=3 locally_generated=1
Mar 15 19:54:40 Alik wpa_supplicant[289]: wlp2s0: CTRL-EVENT-SCAN-STARTED
Last edited by ollen (2014-03-16 00:17:44)
Similar Messages
-
Officejet 6700 looses wireless connection to MAC
My 6700 keeps loosing it connection with my mac which is running 10.10.4 and the fault seems to have occurred at the time this ios update installed. I have had the mac just over a year and its all worked fine until the 10.10.4 update. I have tried re-booting the airport extreme, the mac, deleting the printer and re-installing none of which resolves the problem fully. If I re-boot the printer it will be found and I can print, but if the next job is more than 10 mins later the mac looses the printer again and will not find it. The same fault also seem present with my ipad retine display model running ios 8.4, again this has been working well for nearly two years. HELP please
Yes distance/signal strength maters greatly for wireless.
Get one of these...
http://eshop.macsales.com/item/NewerTech/MXP2802NU2C/
A 10' USB extension cable...
http://eshop.macsales.com/item/Micro%20Accessories/USB2AA120MF/
And place it high in the Den as close to the source as possible, or near openings where the source is more direct. -
Color Laserjet Pro 100 (M175NW) looses wireless connection
Hi,
the printer goes offline from the local wlan after working ok 12 to 24 hrs.
symptoms:
* wireless LED on the printer blinking after waking the printer with the ok button
* wireless status page: not connected
* wireless status page: no wireless lans are found (minimum four others are active)
* wireless status page: always 69-71 disconnects (link quality is good, distance from router 5m)
* wireless lan switched off-on from printer panel: wireless led stays off, no blinking
my tests:
* no difference with/without power save mode
* no difference using router from TP-Link or Arcadyan
* no difference using no/standard/long group key interval on the router
* no difference using only ip4/all services on the printer
* no difference enabling/disabling ip6 on the printer
* no difference printing/not printing during 24 hrs
* no difference using channel 1/7 on the wlan (no other networks on these channels)
workaround:
printer off - on, everthing back to normal, but I am not happy with that
My settings
* printer firmware new: Version:20120806
* static ip
* wpa2-personal aes
* windows vista all patches installed
* current hp printer driver
* wlan settings transferred via usb during standard install
my guess:
buggy firmware or defective network card in the printer
Any ideas? Device is on warranty...Printer does not maintain wireless connection.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02817031&tmp_task=solveCategory&cc=us&dlc=en&la...
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired! -
[SOLVED] No wireless connection with linux-3.2.2-1
After upgrading to linux-3.2.2-1, my wireless connection stopped working. It "connects", but I can't get an IP address through dhcp. Assigning an IP manually doesn't do the trick, I can't even reach the router through ping.
Downgrading to 3.2.1-2 fixes the issue.
I suspect this may be a regression but I couldn't find any information or reports of other people having the same problem anywhere.
I should note that I can establish a working connection when running the new kernel by using an external USB wireless device, so this probably has to do with the modules/drivers of my network card (?).
This is the ouput of some commands when running the new kernel (wlan1 is the device mentioned avobe):
$ ifconfig -a
eth0: flags=4098<BROADCAST,MULTICAST> mtu 1500 metric 1
ether 40:61:86:18:60:2d txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 43 base 0x2000
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 16436 metric 1
inet 127.0.0.1 netmask 255.0.0.0
loop txqueuelen 0 (Local Loopback)
RX packets 22 bytes 1420 (1.3 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 22 bytes 1420 (1.3 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 metric 1
ether 1c:4b:d6:5c:47:dd txqueuelen 1000 (Ethernet)
RX packets 59 bytes 18759 (18.3 KiB)
RX errors 0 dropped 4 overruns 0 frame 0
TX packets 3 bytes 1161 (1.1 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 metric 1
ether d8:5d:4c:8f:49:43 txqueuelen 1000 (Ethernet)
RX packets 449 bytes 144928 (141.5 KiB)
RX errors 0 dropped 8 overruns 0 frame 0
TX packets 9 bytes 1551 (1.5 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
$ lspci
00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 12)
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 12)
00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06)
00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06)
00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06)
00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06)
00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06)
00:1c.3 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 4 (rev 06)
00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06)
00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6)
00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06)
00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 06)
00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06)
00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06)
05:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)
06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02)
3f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02)
3f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02)
3f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02)
3f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02)
3f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02)
3f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02)
$ lsmod
Module Size Used by
uvcvideo 64311 0
videodev 82101 1 uvcvideo
ath9k_htc 56902 0
v4l2_compat_ioctl32 8316 1 videodev
media 10597 2 videodev,uvcvideo
arc4 1410 4
ath9k 87343 0
ath9k_common 2096 2 ath9k,ath9k_htc
ath9k_hw 347282 3 ath9k_common,ath9k,ath9k_htc
ath 14802 4 ath9k_hw,ath9k_common,ath9k,ath9k_htc
mac80211 228367 2 ath9k,ath9k_htc
joydev 9895 0
cfg80211 172260 4 mac80211,ath,ath9k,ath9k_htc
rfkill 15498 1 cfg80211
i2c_i801 8187 0
snd_hda_codec_hdmi 24121 1
snd_hda_codec_realtek 194997 1
snd_hda_intel 23343 0
snd_hda_codec 89160 3 snd_hda_intel,snd_hda_codec_realtek,snd_hda_codec_hdmi
snd_hwdep 6389 1 snd_hda_codec
snd_pcm 74780 3 snd_hda_codec,snd_hda_intel,snd_hda_codec_hdmi
snd_page_alloc 7153 2 snd_pcm,snd_hda_intel
snd_timer 19544 1 snd_pcm
r8169 49040 0
iTCO_wdt 11885 0
snd 59214 7 snd_timer,snd_pcm,snd_hwdep,snd_hda_codec,snd_hda_intel,snd_hda_codec_realtek,snd_hda_codec_hdmi
mii 4059 1 r8169
fan 2426 0
processor 25582 0
battery 6453 0
thermal 7799 0
ac 2344 0
evdev 9530 4
mei 32414 0
intel_ips 11213 0
wmi 8475 0
iTCO_vendor_support 1961 1 iTCO_wdt
psmouse 61311 0
pcspkr 1819 0
serio_raw 4429 0
soundcore 6210 1 snd
vboxnetflt 17159 0
vboxdrv 1790690 1 vboxnetflt
ext4 417116 1
crc16 1359 1 ext4
jbd2 71243 1 ext4
mbcache 5881 1 ext4
usb_storage 44519 2
sr_mod 14951 0
cdrom 36681 1 sr_mod
sd_mod 28307 3
ahci 20037 0
libahci 19559 1 ahci
libata 166654 2 libahci,ahci
scsi_mod 133443 4 libata,sd_mod,sr_mod,usb_storage
ehci_hcd 40698 0
usbcore 146241 5 ehci_hcd,usb_storage,ath9k_htc,uvcvideo
usb_common 954 1 usbcore
i915 418631 7
video 11164 1 i915
button 4470 1 i915
i2c_algo_bit 5263 1 i915
drm_kms_helper 26137 1 i915
drm 188362 3 drm_kms_helper,i915
i2c_core 20492 6 drm,drm_kms_helper,i2c_algo_bit,i915,i2c_i801,videodev
intel_agp 10904 1 i915
intel_gtt 14519 3 intel_agp,i915
Thanks in advance.
Last edited by Ideka (2012-02-02 21:23:38)Ideka wrote:I suspect this may be a regression but I couldn't find any information or reports of other people having the same problem anywhere.
You must not have searched very long then, because you've missed not one, but two threads:
https://bbs.archlinux.org/viewtopic.php?id=134374
https://bbs.archlinux.org/viewtopic.php?id=134580 -
When I'm on the internet using the airport, I loose my connection all the time. The I don't loose the internet, it just like freezes and eventually it will come back and the action I have tried to get it to do, like go to another page or link etc. it will have done. I can still use the computer itself just not the internet. Crazy huh?
I have checked in troubleshooting and gone through the manual. I'm not finding an answer. I've checked with my Internet Service Provider, it's not them. Everyone else in my household is staying connected just fine. Is my airport card just going out and I'm out of luck until I replace it? I'm hoping maybe there is an upgrade or something that might help. If you have a suggestion please let me know.
ThanksSolution may be found if you search in the "More Like This" section over in the right column.
-
[Solved] No wireless connection after reboot.
I installed through a wireless connection. I installed inside of VirtualBox, and I installed wireless_tools, wpa_supplicant, and wpa_actiond dialog. So I had wireless internet on the live cd, but not after the install. Is there some driver that I am missing? Is there some VirtualBox special feature I am missing?
lspci | grep -i net = intel corporation 82540em gigabit ethernet controller
I don't think I need to install any additional firmware for this driver.
iwconfig = enp0s3 no wireless extensions
lo no wireless extensions
I tried adding manually loading iwl3945 and iwl4965, one of which I think is my driver.
Any help would be appreciated. Thanks.
The fix was typing "systemctl enable dhcpcd".
Last edited by SCLegend (2013-02-05 19:44:47)Ideka wrote:I suspect this may be a regression but I couldn't find any information or reports of other people having the same problem anywhere.
You must not have searched very long then, because you've missed not one, but two threads:
https://bbs.archlinux.org/viewtopic.php?id=134374
https://bbs.archlinux.org/viewtopic.php?id=134580 -
[SOLVED] unstable wireless connection
Hi,
Wireless connection has some troubles. I don't get connection drops or anything in everyting.log mentioning errors with wlan. I tried wicd, Networkmanager and netcfg - but alas - no better results in any of them. The problem is that when checking mail, upgrading packages, ... sometimes connection cannot be made. Most of the time, running the same program immediately a second time, won't give this error. Less error-tolerant programs just crash/quit with an error-message.
Errors are like (in Dutch, I tried an English translation after ***):
Herleiden van v3.lscache4.c.bigcache.googleapis.com... mislukt: Naam of dienst is niet bekend. *** Failed to resolve from ... Name or service unknown.
wget: kan host-adres '‘v3.lscache4.c.bigcache.googleapis.com’' niet herleiden *** Cannot resolve host-addres
I've on the same laptop Sabayon and Ubuntu running where those problems do not occur.
Wireless/ lspci:
03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)
lsmod:
Module Size Used by
aes_x86_64 7508 1
cryptd 8309 0
aes_generic 26138 1 aes_x86_64
joydev 9927 0
snd_hda_codec_hdmi 24240 1
snd_hda_codec_conexant 46938 1
asus_laptop 17142 0
snd_hda_intel 23631 1
arc4 1410 2
snd_hda_codec 92950 3 snd_hda_intel,snd_hda_codec_conexant,snd_hda_codec_hdmi
snd_hwdep 6389 1 snd_hda_codec
snd_pcm 74812 3 snd_hda_codec,snd_hda_intel,snd_hda_codec_hdmi
snd_page_alloc 7153 2 snd_pcm,snd_hda_intel
snd_timer 19544 1 snd_pcm
snd 59858 9 snd_timer,snd_pcm,snd_hwdep,snd_hda_codec,snd_hda_intel,snd_hda_codec_conexant,snd_hda_codec_hdmi
ath9k 92940 0
soundcore 6210 1 snd
jmb38x_ms 8417 0
serio_raw 4653 0
ath9k_common 2096 1 ath9k
jme 35085 0
ath9k_hw 358828 2 ath9k_common,ath9k
ath 15393 3 ath9k_hw,ath9k_common,ath9k
mei 32568 0
sdhci_pci 10568 0
psmouse 69904 0
input_polldev 2914 1 asus_laptop
memstick 6974 1 jmb38x_ms
mac80211 396060 1 ath9k
sdhci 23438 1 sdhci_pci
iTCO_wdt 12941 0
mii 4091 1 jme
iTCO_vendor_support 1961 1 iTCO_wdt
cfg80211 176921 3 mac80211,ath,ath9k
i2c_i801 8187 0
mmc_core 82804 2 sdhci,sdhci_pci
i2c_core 20524 1 i2c_i801
evdev 9626 7
sparse_keymap 3120 1 asus_laptop
thermal 7799 0
rfkill 15530 2 cfg80211,asus_laptop
button 4470 0
battery 6453 0
ac 2344 0
video 11164 0
intel_agp 10904 0
intel_gtt 14519 1 intel_agp
cpufreq_powersave 990 0
acpi_cpufreq 5877 1
mperf 1275 1 acpi_cpufreq
processor 25981 1 acpi_cpufreq
ext4 425832 3
crc16 1359 1 ext4
jbd2 71939 1 ext4
mbcache 5881 1 ext4
sd_mod 28371 5
sr_mod 15047 0
cdrom 36489 1 sr_mod
ahci 20133 4
libahci 19487 1 ahci
libata 167582 2 libahci,ahci
scsi_mod 134028 3 libata,sr_mod,sd_mod
ehci_hcd 43864 0
usbcore 146465 2 ehci_hcd
usb_common 954 1 usbcore
Can you help to pinpoint the problem and try to find a solution?
Thanks in advance,
david
Edit: solution: Disabling ipv6
Last edited by davidbe (2012-04-23 18:15:21)The thing is, I cannot run it when it happens, because it is not a disconnection. It is more like small hickups. Fault-tolerant applications won't give an error. But using wget/curl might fail 1, 2 or three consecutive times, but can succeed flawlessly a 4th time. :-/
ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000
link/ether e0:cb:4e:f6:77:9e brd ff:ff:ff:ff:ff:ff
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 1c:4b:d6:5b:c0:a8 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.10/24 brd 192.168.1.255 scope global wlan0
inet6 fe80::1e4b:d6ff:fe5b:c0a8/64 scope link
valid_lft forever preferred_lft forever
ip route
default via 192.168.1.1 dev wlan0 metric 303
192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.10 metric 303
iwconfig
lo no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:"Mobistar-3a40"
Mode:Managed Frequency:2.437 GHz Access Point: 5C:33:8E:BF:B3:60
Bit Rate=65 Mb/s Tx-Power=15 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=56/70 Signal level=-54 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:24 Missed beacon:0
eth0 no wireless extensions.
cat /etc/resolv.conf
domain home
nameserver 192.168.1.1
ping www.google.com -c 10
PING www.google.com (173.194.66.104) 56(84) bytes of data.
64 bytes from we-in-f104.1e100.net (173.194.66.104): icmp_req=1 ttl=48 time=23.6 ms
64 bytes from we-in-f104.1e100.net (173.194.66.104): icmp_req=2 ttl=47 time=23.8 ms
64 bytes from we-in-f104.1e100.net (173.194.66.104): icmp_req=3 ttl=48 time=24.4 ms
64 bytes from we-in-f104.1e100.net (173.194.66.104): icmp_req=4 ttl=47 time=23.9 ms
64 bytes from we-in-f104.1e100.net (173.194.66.104): icmp_req=5 ttl=47 time=25.0 ms
64 bytes from we-in-f104.1e100.net (173.194.66.104): icmp_req=6 ttl=47 time=26.2 ms
64 bytes from we-in-f104.1e100.net (173.194.66.104): icmp_req=7 ttl=48 time=26.0 ms
64 bytes from we-in-f104.1e100.net (173.194.66.104): icmp_req=8 ttl=47 time=25.4 ms
64 bytes from we-in-f104.1e100.net (173.194.66.104): icmp_req=9 ttl=47 time=25.0 ms
64 bytes from we-in-f104.1e100.net (173.194.66.104): icmp_req=10 ttl=48 time=24.3 ms
--- www.google.com ping statistics ---
10 packets transmitted, 10 received, 0% packet loss, time 9013ms
rtt min/avg/max/mdev = 23.607/24.796/26.204/0.885 ms
ping 8.8.8.8 -c 10
PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
64 bytes from 8.8.8.8: icmp_req=1 ttl=50 time=27.0 ms
64 bytes from 8.8.8.8: icmp_req=2 ttl=50 time=27.2 ms
64 bytes from 8.8.8.8: icmp_req=3 ttl=50 time=26.7 ms
64 bytes from 8.8.8.8: icmp_req=4 ttl=50 time=26.9 ms
64 bytes from 8.8.8.8: icmp_req=5 ttl=50 time=27.3 ms
64 bytes from 8.8.8.8: icmp_req=6 ttl=50 time=27.1 ms
64 bytes from 8.8.8.8: icmp_req=7 ttl=50 time=28.2 ms
64 bytes from 8.8.8.8: icmp_req=8 ttl=50 time=27.1 ms
64 bytes from 8.8.8.8: icmp_req=9 ttl=50 time=27.7 ms
64 bytes from 8.8.8.8: icmp_req=10 ttl=50 time=27.1 ms
--- 8.8.8.8 ping statistics ---
10 packets transmitted, 10 received, 0% packet loss, time 9012ms
rtt min/avg/max/mdev = 26.795/27.299/28.266/0.407 ms -
Loose wireless connection with security turned on
I am able to get a wireless connection when the wireless network has no security enabled. But when the security is turned on - using WEP or WPA (TKIP) - I can no longer get a connection. The error message says that the password is not correct (however it is).
Of note: I have another G4 (aluminum 1.33 GHz) running the same version of OS X that does not have a problem connecting with the security turned on.
I have the same problem at home or with other wireless networks that require passwords.
At home I have a linksys wireless router.
Thanks!
1 GHz PowerPC G4 Mac OS X (10.4.8)i have a very similar situation to yours... my airport cannont get an IP address from any wireless network with security enabled. if it is completely open, it will lock in and get an IP address and everything is fine, but with ANY kind of security enabled, it wont get an IP and gives me the standard "169...." addresses. If i turn off security on a given base station, the machine will suddenly get an IP address, so I know this is a problem with the machine and not the router as other wifi devices connect to the router fine.
I've tried using standard WEP, WPA, and also MAC-address security and i get the same problem across all of them. Ive tried this with about 5 different routers, 3 linksys, 1 netgear and one dLink. -
My MacBook Pro looses connection after 15-30minutes unless within 2-3ft. of my AirPort Express. My G-4 stays connected just fine. My son's less than one year old MacBook stays connected. My old, old HP (7+ years) stays connected. I have Comcast but I'm not sure of the "product". My network is high speed cable with an Ambit modem and AirPort Express. My MacBook Pro does hold a signal unless it is within 2-3 of the AirPort and this is true in other locations such as my work (not sure of the router since it's a public school building) and my friend's house (Belkin router). Here is a list of things I have done so far to try to remedy the situation:
Per Apple Store Genius:
removed all wireless devices (phones, etc.) still no solution
checked for hardware issues
Per Apple Support:
changed channels
run utility and repair disks
uninstalled the operating system (wiped the hard drive clean) and reinstalled OS 10.5.6
Tried myself:
turned on Interference Robustness
All of this has has little impact/effect on holding the connection. Apple Support can no longer help. Apple Genius says they have done all they can or will do telling me it's interference. I bought my machine in 2006 and did not have this issue until Wed. 4/8/09. I am wondering why interference just on the newest Mac and why suddenly. Most importantly, how to solve?
Can anyone advise?First, if you are not referring to a unibody MacBook Pro, you should post in the following forum, as you will be able to receive better suggestions.
http://discussions.apple.com/forum.jspa?forumID=1149
Second, can you try a different Internet connection in a different location? If it works there, the problem is not with your MacBook Pro.
Good luck! -
Two desktop computers - one constantly looses wireless connection
Hi,
I have a Linksys Wireless-G Broadband Router with Speedbooster (model WRT54GS) for use with a cable modem. I have two Dell Desktops, both with Linksys Wireless-G PCI with SpeedBooster Cards. One desktop works perfect with the network, the other constantly loses its connection. Signal strength on both are good, both computers are relatively new (the one with problems is ~ 1 yr old). I either have to 'repair' the connection or reboot. It will stay connected for various lengths of time (sometimes a minute, sometimes 10 minutes!). If i click on the 'Wireless Network Connection' icon, it will often show 'Connected' to my network, but the button in the corner shows 'Connect' (shouldn't it say 'Disconnect?).
Any help is appreciated!
ThanksSurely, the router is working since one wireless pc is working already. You could focus more on the adapter. Since it has been a year already, you could try to update the driver of your nonworking adapter.
-
4200v2 looses wireless connection after 24hrs
Hello All
I upgraded my Linksys from 160n router to 4200V2 router. I configured 3 wireless Linksys webcams and they work fine. After 24hrs they i cannnot connect the via HTTP and webcames IP addresses disapear from the DHCP client table. If reboot the webcames the it works fine for next 24hrs. I did not make any modification to any settings and the setting looks just like i had on the 160N router. Any help/suggestions please??You could have tried the following settings as well:
A] With the help of Cisco Connect Software (if at all you have installed the router with the help of this software)
1] Open the software and go to the option which says "Router Settings"
2] Then click on the option which says "Advanced Settings" which will take you to the router's configuration page.
3] Lower the MTU (Maximum Transmission Unit) from 1500 to 1400 or less (usually found on your router's main/ basic setup page). Here is the link for determining and setting up the correct MTU size: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=fbf8e8564632422eaa8ea80bf9dcba64_386.xml&pid=80&re...
B] If you haven't installed Cisco Connect then you can log on to the router's user interface using it's default IP address in the browser which is 192.168.1.1 and type in 'admin' as the password leaving the user name field blank. This will take you to the router's web interface and then follow steps as mentioned above to make the changes.
Then check the connectivity status… -
Looses wireless connection all the time.
Hi
I have a problem with my macbook pro, it looses its internet connection all the time. I don't know why since it's quite close to it's modem and other laptops that's more far away works fine. Any idea?
Best regards FrankenstenDoes the router have the latest firmware? What happens when you are at a hotspot or a Starbucks?
-
Wireless connectivity issues with Macbook Pro and At&t service HELP!!!!!
I have three Computers two PC's and one Macbook Pro( the latest model).My desktop PC is used by ethernet, my girls laptop is used wirelessly and finally my MBP was being used wirelessly.
I started off with only the two PCs and my internet connection never had a problem and I was doing everything from: on the internet to downloading.
Before I bought my MBP I had also switched from internet and phone bundle to just internet from At&t service. So when I got my first MBP I notice that I was loosing wireless connection with both my girls pc laptop and my MBP so i thought it was because I had just switched service, though they send out a service technician and we came to a conclusion that it was the MBP. (I was loosing signal via wireless and ethernet). So we tried to see if both my girls laptop(wireless) and my PC desktop (ethernet) would run into the same issue which it did not.(MBP was turned off)
So I decided to go my nearest Apple store and let them know what was going on. So I told them what was going on and they said It must be the airport card, and they ended up changing it. When I get home I discover that not only I am having the same issue but other issues too. I went back they ran some diagnostic and they said it was defective and they gave me a new one few days later.
So in the mean time that I waited for my new one to arrive I used my PC desktop and my girl kept using her laptop and guess what no issue what so ever for one whole week. Now I receive my new MBP(they bumped the specs a little), went home set it up and still the same issue though I dont have the issue when Im using via ethernet. Just a view minutes ago I tried removing the ethernet and using the airport/wireless and within a few minutes I lost the signal.
I have the gateway 2WIRE model(2701HG-B) modem/router.
Is there something wrong? what do I have to do to make this work?Hi Guys, I bough my Mac almost two years ago. All this time I have experienced the same issue. There are tons of discussions re this issue in the internet. Unfortunately, Apple has done nothing to fix it. I have tried a lot of different options, but they work no longer then 1-2 days. The official fix - does not exist so far. It is quit strange, isn't? I can share my experience: if you go to AirPort Utility - Manual Setup - Wireless and then change Channel, it could help you till the moment you restart your computer; next time you need to repeat it again. It takes 2 minutes. Not sure that it would work for you but you could give it a try. Well, not the best option. Anyway Apple must fix it asap! Hello Apple, do you hear us? Good luck.
-
Wireless connection loss on my imac and not on my macbook pro
i have an imac with software 10,4,11 and since a certain time every time my imac go in sleep, re-waking up he loses wireless connection for a few seconds so internet blocks, i hav also a macbook pro, same connection same software and no problem at all. who can help me how to solve my wireless connection problem
If it's an encrypted connection, One thing that can work, try this, please ignore the exact symptoms and connection and Hardware types, it's worked for many others than the stated...
http://docs.info.apple.com/article.html?artnum=304482 -
Why do I loose my wireless connection?
Can someone tell me why I loose my wireless connection from my laptop when I go to make a phone call with my phone?
Solved!
Go to Solution.Your phone is probably on the 2.4Ghz frequency which is the same frequency wireless routers operate on. Try changing the channel on the router to one that is far enough away from the phone's frequency so they don't interfere with each other.
To change the channel on the router:
In Internet Explorer, type 192.168.1.1 into the address bar
On the login page that comes up, type admin for the username and password1 for the password (ignore the dots)
Click Change Wireless Settings under Quick Links in the My Router column of the front page.
Under option 3. Channel, select a number from 1 - 11 then click Apply at the bottom of the page.
Click Apply again to save the changes if it asks.
It is pretty much trial and error in determining which channel will be furthest from your phone's frequency, and you might even not find a channel that keeps your wireless connection up every time your on the phone. I had the same problem with my own cordless phone and a linksys router that I ended up having to purchase a new phone in the 5.8Ghz range to keep my connection. With that said, I hope you have better luck then me with this situation.
Brennoko
Verizon Telecom
Fiber Solutions Center
Notice: Content posted by Verizon employees is meant to be informational and does not supercede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or Plan.
Maybe you are looking for
-
How could be possible to deliver Mac Pro without a keyboard?
I've ordered my Mac Pro in Bulgaria from the local Apple reseller - http://www.bbs.bg/ but when they delivered my Mac I've found that there isn't keyboard. There is a mouse, software, manuals, cables, but the keyboard is missing. Peter Penkov, Busine
-
I am trying to make it clearer, I use a scxi-1161 and two of its relay channels to operate an MOV. I want to be able to apply power to two different pins on the MOV using two seperate relay channels.. but I want to be able to have it automatically cy
-
I lost my keycode and can`t reset my iphone 4
please, i can not reset my iphone because i lost the key code
-
Okay so I'm trying to update my iPhone 3GS but when I click the "Download and Install" button I get the error message "The iTunes update server could not be contacted. Please check you Internet connection, or try again later" I've already made sure t
-
Can I add Adobe Captivate to an existing Creative Cloud Subscription?
and if so, how much additional? Thanks! Kim