[Solved]Usb Pendrive not detected

Hello, I have a xfce4 desktop and when i insert my flashdrive its not detected in thunar.
I have ticked the options to "mount removable device when inserted" and "mount removable drivers when hot-plugged".
What do I have to do to see my pendrive in Thunar!.
Thanks for reading
Last edited by Jean3799 (2014-06-24 06:00:36)

Make sure gvfs is installed.
sudo pacman -S gvfs
Read in the wiki here and here.

Similar Messages

[SOLVED]Usb drive not detected in kde

not appear in the notification, but in dmesg appear
5458.314319] usb 2-3: new high-speed USB device number 4 using ehci-pci
[ 5458.508037] usb-storage 2-3:1.0: USB Mass Storage device detected
[ 5458.508098] scsi12 : usb-storage 2-3:1.0
[ 5458.508149] usbcore: registered new interface driver usb-storage
[ 5459.585989] scsi 12:0:0:0: Direct-Access USB DISK Pro PMAP PQ: 0 ANSI: 4
[ 5460.612052] sd 12:0:0:0: [sdb] 31260672 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 5460.613431] sd 12:0:0:0: [sdb] Write Protect is off
[ 5460.613434] sd 12:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 5460.614802] sd 12:0:0:0: [sdb] No Caching mode page found
[ 5460.614805] sd 12:0:0:0: [sdb] Assuming drive cache: write through
[ 5460.619671] sd 12:0:0:0: [sdb] No Caching mode page found
[ 5460.619674] sd 12:0:0:0: [sdb] Assuming drive cache: write through
[ 5460.642643] sdb: sdb1
[ 5460.649748] sd 12:0:0:0: [sdb] No Caching mode page found
[ 5460.649751] sd 12:0:0:0: [sdb] Assuming drive cache: write through
[ 5460.649753] sd 12:0:0:0: [sdb] Attached SCSI removable disk
[ 5476.956859] ath5k: ath5k_hw_get_isr: ISR: 0x00000400 IMR: 0x00000000
[ 5613.844729] usb 2-3: USB disconnect, device number 4
[ 5616.296689] usb 2-3: new high-speed USB device number 5 using ehci-pci
[ 5616.425854] usb-storage 2-3:1.0: USB Mass Storage device detected
[ 5616.425903] scsi13 : usb-storage 2-3:1.0
[ 5617.501846] scsi 13:0:0:0: Direct-Access USB DISK Pro PMAP PQ: 0 ANSI: 4
[ 5618.534031] sd 13:0:0:0: [sdb] 31260672 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 5618.535398] sd 13:0:0:0: [sdb] Write Protect is off
[ 5618.535401] sd 13:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 5618.536784] sd 13:0:0:0: [sdb] No Caching mode page found
[ 5618.536790] sd 13:0:0:0: [sdb] Assuming drive cache: write through
[ 5618.541762] sd 13:0:0:0: [sdb] No Caching mode page found
[ 5618.541765] sd 13:0:0:0: [sdb] Assuming drive cache: write through
[ 5618.564608] sdb: sdb1
[ 5618.571842] sd 13:0:0:0: [sdb] No Caching mode page found
[ 5618.571845] sd 13:0:0:0: [sdb] Assuming drive cache: write through
[ 5618.571847] sd 13:0:0:0: [sdb] Attached SCSI removable disk
uname -a
Linux tarro 3.13.5-1-ARCH #1 SMP PREEMPT Sun Feb 23 00:25:24 CET 2014 x86_64 GNU/Linux
cat /etc/group
root:x:0:root
bin:x:1:root,bin,daemon
daemon:x:2:root,bin,daemon
sys:x:3:root,bin
adm:x:4:root,daemon
tty:x:5:
disk:x:6:root,darkmind
lp:x:7:daemon,darkmind
mem:x:8:
kmem:x:9:
wheel:x:10:root,darkmind,pct
ftp:x:11:
mail:x:12:
uucp:x:14:
log:x:19:root
utmp:x:20:
locate:x:21:
rfkill:x:24:
smmsp:x:25:
http:x:33:
games:x:50:darkmind
lock:x:54:
uuidd:x:68:
dbus:x:81:
network:x:90:darkmind,pct
video:x:91:darkmind,pct
audio:x:92:darkmind,pct
optical:x:93:pct,darkmind
floppy:x:94:
storage:x:95:darkmind
scanner:x:96:pct,darkmind
power:x:98:
nobody:x:99:
users:x:100:pct
systemd-journal:x:190:
polkitd:x:102:
transmission:x:169:
avahi:x:84:
usbmux:x:140:darkmind
ntp:x:87:
mysql:x:89:
kdm:x:135:
git:x:999:
pct:x:1001:
(i'm darkmind)
somebody help?
Last edited by dunkles (2014-02-25 22:50:53)

ewaller wrote:I am not sure what that means. Are you expecting a pop up notification in KDE?
yes
ewaller wrote:Does Dolphin show the volumes?
not show the volumes, nothing happens when plug a usb drive
ewaller wrote:Do you have udisks installed? How about udisks2?
yes

USB devices not detected in VMware [SOLVED; Using Virtualbox instead]

I am running Arch as a host and XP on VMWare workstation 7. My primary purpose of installing XP on VMWare was to use my edit my Line6 POD (behaves as a usb sound card) and get my USB TV Tuner box to work. The big problem that I am facing is that VMWare is not detecting any USB device (not even my USB Hard Drive).
I have the usb controller installed.
Any suggestions?
Last edited by devadittya (2009-11-24 20:04:45)

I don't know vmware but with other virtual machines there is often a configuration option whether usb drives should be automatically mounted or not. Sometimes automounting also only works if the vm has the focus, i.e. is the active window.

USB Devices Not Detected and High CPU Usage

Hello, I'm using arch on a Dell 1720 laptop.
I have some weird issues involving detection of USB devices.
When the laptop is on battery and I plug in a USB mouse the power flickers on and flickers off again; nothing in the logs/dmesg.
If I then connect the AC adapter the reconnect the mouse, the same happens, except the CPU usage hits 87%+ on one core.
Running
sudo rmmod ehci_hcd
solves the problem; the CPU usage drops and the mouse gets detected.
Subsequent attempts to hotplug USB devices does nothing, no high CPU and no Power.
Rebooting the computer is the only way to use USB devices at the moment.
usb-autosuspend is disabled in laptop-mode.
uname -a:
Linux MatSalleh 2.6.39-ck #1 SMP PREEMPT Sun Jun 5 18:30:30 EDT 2011 x86_64 Intel(R) Core(TM)2 Duo CPU T7250 @ 2.00GHz GenuineIntel GNU/Linux
The same happens with the stock kernel too
My kernel line in grub:
kernel /vmlinuz26-ck root=/dev/sda3 elevator=bfq ro resume=/dev/sda2
Any ideas?
Thanks,
Chris.

lilsirecho wrote:Perhaps the USB connector is damaged, causing excess power drain suggesting that the current limiter isn't functioning.
I highly doubt it's that, it was working fine on ubuntu just days before...
tydell wrote:I had similar problem with USB pendrive, it wasn't detected and it makes high cpu usage. It was problem with ehci_hcd module
This one helps me to solve this problem
My USB devices don't even get detected, so that script won't work.
Last night I hibernated my computer after not using any USB devices, on resume, my CPU usage was 100%, removing the ehci_hcd module fixed it.
Any more ideas?
I'm tempted to build a vanilla kernel...

[SOLVED] k3b does not detect optical drive

Hello,
I am running Arch Linux x86_64 with recent updates. I have k3b 2.0.3 and when I launch it I get message that it does not detect my optical drive, and I need hal daemon. I checked, udev is running, node in dev /dev/sr0 has root.optical, my user is in optical group. How do I fix this? I want to burn BluRay disk, maybe k3b even does not support it? And is there a better tool for optical discs than k3b? I use KDE 4 so Qt tool would be nice
Last edited by adomas (2015-01-09 17:34:05)

[EDIT] I think problem is solved. Not sure how, but after reboot it works now
Thank you for you reply, Lone_Wolf
Permissions seems to be ok:
[adomas@voidbox ~]$ ls -l /dev/sr0
brw-rw---- 1 root optical 11, 0 Jan 9 21:18 /dev/sr0
[adomas@voidbox ~]$
And about dependencies I think I have what I need:
[root@voidbox adomas]# pacman -Qi k3b
Name : k3b
Version : 1:2.0.3a-1
Description : Feature-rich and easy to handle CD burning application
Architecture : x86_64
URL : http://sourceforge.net/projects/k3b/
Licenses : GPL
Groups : None
Provides : None
Depends On : kdebase-runtime libkcddb libsamplerate libmad ffmpeg taglib libmpcdec libdvdread cdrkit
libxft
Optional Deps : dvd+rw-tools: for dvd burning support [installed]
vcdimager: for vcd burning support
transcode: for advanced mpeg conversion support
emovix: for bootable multimedia cd/dvd support
cdrdao: for disk-at-once (DAO) mode support [installed]
cdparanoia: for cd ripping support
Required By : None
Optional For : None
Conflicts With : None
Replaces : None
Installed Size : 33.81 MiB
Packager : Eric Belanger <[email protected]>
Build Date : Thu 06 Nov 2014 05:21:31 AM EET
Install Date : Wed 07 Jan 2015 07:28:57 PM EET
Install Reason : Explicitly installed
Install Script : Yes
Validated By : Signature
[root@voidbox adomas]#
What else can be a problem? By the way may optical drive is external, connected via USB, if it makes any difference.
Last edited by adomas (2015-01-09 17:33:50)

[Potentially Solved] Touchpad sometimes not detected possible IRQ.

Edit:
Potentially solved: since adding the below entries to my bootloader I have not encountered the issue, or it may be just a coincidence.
append to the boot line: i8042.nomux=1 i8042.reset
I've been experiencing an issue for the last few years which has bugged me across two different brands of laptop, but has been very hard to debug due to how random the event seems to occur.
One in every 20 or so boots, the touchpad on my laptop (Lenovo Z500) is not detected; not just by X, but by the system as a whole, it's as if it has been physically disconnected somehow.
It will take a few good reboots for the system to detect it again, and the problem disappears for another few days/weeks
One strange thing I have noticed, is that when looking at the listing of interrupts during a 'failed touchpad boot', IRQ 12, which I believe is normally the touchpad, has vanished.
I'm not very clued up on these matters so I'm not sure how to start debugging this, and working out if the issue is down to my setup of the system or not.
Any ideas on what could be causing this?
Thanks.
Output of /proc/interrupts during a working boot:
CPU0 CPU1 CPU2 CPU3
0: 23 0 0 0 IO-APIC-edge timer
1: 16 723 9 10 IO-APIC-edge i8042
8: 0 0 0 1 IO-APIC-edge rtc0
9: 299 118 10 14 IO-APIC-fasteoi acpi
12: 845 21415 146 77 IO-APIC-edge i8042
16: 461 8993 74 44 IO-APIC-fasteoi ehci_hcd:usb1
17: 0 0 0 0 IO-APIC-fasteoi ath9k
23: 2 25 5 1 IO-APIC-fasteoi ehci_hcd:usb2
41: 5 22 0 2 PCI-MSI-edge xhci_hcd
42: 1557 1065 596 500 PCI-MSI-edge ahci
43: 11 2 0 0 PCI-MSI-edge mei_me
44: 266 0 0 0 PCI-MSI-edge snd_hda_intel
46: 4 28 26 1 PCI-MSI-edge i915
NMI: 0 0 0 0 Non-maskable interrupts
LOC: 3002 12958 2572 1842 Local timer interrupts
SPU: 0 0 0 0 Spurious interrupts
PMI: 0 0 0 0 Performance monitoring interrupts
IWI: 88 170 115 197 IRQ work interrupts
RTR: 1 0 0 0 APIC ICR read retries
RES: 367 332 393 431 Rescheduling interrupts
CAL: 129 71 24 58 Function call interrupts
TLB: 99 72 157 892 TLB shootdowns
TRM: 0 0 0 0 Thermal event interrupts
THR: 0 0 0 0 Threshold APIC interrupts
MCE: 0 0 0 0 Machine check exceptions
MCP: 2 2 2 2 Machine check polls
THR: 0 0 0 0 Hypervisor callback interrupts
ERR: 0
MIS: 0
Output of /proc/interrupts during a non-working boot:
CPU0 CPU1 CPU2 CPU3
0: 23 0 0 0 IO-APIC-edge timer
1: 9 235 2 11 IO-APIC-edge i8042
8: 0 0 1 0 IO-APIC-edge rtc0
9: 217 44 24 40 IO-APIC-fasteoi acpi
16: 96 2512 38 173 IO-APIC-fasteoi ehci_hcd:usb1
17: 0 0 0 0 IO-APIC-fasteoi ath9k
23: 3 25 1 4 IO-APIC-fasteoi ehci_hcd:usb2
41: 6 23 0 1 PCI-MSI-edge xhci_hcd
42: 1445 937 649 479 PCI-MSI-edge ahci
43: 9 3 0 1 PCI-MSI-edge mei_me
45: 11 10 4 39 PCI-MSI-edge i915
46: 93 80 94 0 PCI-MSI-edge snd_hda_intel
NMI: 0 0 0 0 Non-maskable interrupts
LOC: 1251 3465 1964 692 Local timer interrupts
SPU: 0 0 0 0 Spurious interrupts
PMI: 0 0 0 0 Performance monitoring interrupts
IWI: 76 97 47 79 IRQ work interrupts
RTR: 1 0 0 0 APIC ICR read retries
RES: 349 252 190 335 Rescheduling interrupts
CAL: 110 72 30 69 Function call interrupts
TLB: 101 52 817 651 TLB shootdowns
TRM: 0 0 0 0 Thermal event interrupts
THR: 0 0 0 0 Threshold APIC interrupts
MCE: 0 0 0 0 Machine check exceptions
MCP: 2 2 2 2 Machine check polls
THR: 0 0 0 0 Hypervisor callback interrupts
ERR: 0
MIS: 0
Output of /proc/bus/input/devices during a working boot (touchpad detected at bus 0011):
I: Bus=0011 Vendor=0001 Product=0001 Version=ab41
N: Name="AT Translated Set 2 keyboard"
P: Phys=isa0060/serio0/input0
S: Sysfs=/devices/platform/i8042/serio0/input/input0
U: Uniq=
H: Handlers=kbd event0
B: PROP=0
B: EV=120013
B: KEY=402000000 3803078f800d001 feffffdfffefffff fffffffffffffffe
B: MSC=10
B: LED=7
I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button"
P: Phys=PNP0C0C/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:01/PNP0C0C:00/input/input2
U: Uniq=
H: Handlers=kbd event1
B: PROP=0
B: EV=3
B: KEY=10000000000000 0
I: Bus=0019 Vendor=0000 Product=0005 Version=0000
N: Name="Lid Switch"
P: Phys=PNP0C0D/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input3
U: Uniq=
H: Handlers=event2
B: PROP=0
B: EV=21
B: SW=1
I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button"
P: Phys=LNXPWRBN/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
U: Uniq=
H: Handlers=kbd event3
B: PROP=0
B: EV=3
B: KEY=10000000000000 0
I: Bus=0019 Vendor=0000 Product=0000 Version=0000
N: Name="Ideapad extra buttons"
P: Phys=ideapad/input0
S: Sysfs=/devices/platform/VPC2004:00/input/input5
U: Uniq=
H: Handlers=kbd rfkill event4
B: PROP=0
B: EV=13
B: KEY=1400800100c03 400000000300000 0 0
B: MSC=10
I: Bus=0010 Vendor=001f Product=0001 Version=0100
N: Name="PC Speaker"
P: Phys=isa0061/input0
S: Sysfs=/devices/platform/pcspkr/input/input7
U: Uniq=
H: Handlers=kbd event5
B: PROP=0
B: EV=40001
B: SND=6
I: Bus=0003 Vendor=13d3 Product=5170 Version=0730
N: Name="Lenovo EasyCamera"
P: Phys=usb-0000:00:14.0-4/button
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4:1.0/input/input9
U: Uniq=
H: Handlers=kbd event6
B: PROP=0
B: EV=3
B: KEY=100000 0 0 0
I: Bus=0001 Vendor=10ec Product=0269 Version=0001
N: Name="HDA Digital PCBeep"
P: Phys=card0/codec#0/beep0
S: Sysfs=/devices/pci0000:00/0000:00:1b.0/sound/card0/hdaudioC0D0/input8
U: Uniq=
H: Handlers=kbd event7
B: PROP=0
B: EV=40001
B: SND=6
I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH Mic"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1b.0/sound/card0/input10
U: Uniq=
H: Handlers=event8
B: PROP=0
B: EV=21
B: SW=10
I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH Headphone"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1b.0/sound/card0/input11
U: Uniq=
H: Handlers=event9
B: PROP=0
B: EV=21
B: SW=4
I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH HDMI/DP,pcm=3"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1b.0/sound/card0/input12
U: Uniq=
H: Handlers=event10
B: PROP=0
B: EV=21
B: SW=140
I: Bus=0011 Vendor=0002 Product=0007 Version=01b1
N: Name="SynPS/2 Synaptics TouchPad"
P: Phys=isa0060/serio1/input0
S: Sysfs=/devices/platform/i8042/serio1/input/input6
U: Uniq=
H: Handlers=event11 mouse0
B: PROP=5
B: EV=b
B: KEY=e520 10000 0 0 0 0
B: ABS=660800011000003
I: Bus=0019 Vendor=0000 Product=0006 Version=0000
N: Name="Video Bus"
P: Phys=LNXVIDEO/video/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:35/LNXVIDEO:00/input/input13
U: Uniq=
H: Handlers=kbd event12
B: PROP=0
B: EV=3
B: KEY=3e000b00000000 0 0 0
I: Bus=0019 Vendor=0000 Product=0006 Version=0000
N: Name="Video Bus"
P: Phys=LNXVIDEO/video/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:03/input/input14
U: Uniq=
H: Handlers=kbd event13
B: PROP=0
B: EV=3
B: KEY=3e000b00000000 0 0 0
Output of /proc/bus/input/devices during a non-working boot:
I: Bus=0011 Vendor=0001 Product=0001 Version=ab41
N: Name="AT Translated Set 2 keyboard"
P: Phys=isa0060/serio0/input0
S: Sysfs=/devices/platform/i8042/serio0/input/input2
U: Uniq=
H: Handlers=kbd event0
B: PROP=0
B: EV=120013
B: KEY=402000000 3803078f800d001 feffffdfffefffff fffffffffffffffe
B: MSC=10
B: LED=7
I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button"
P: Phys=PNP0C0C/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:01/PNP0C0C:00/input/input3
U: Uniq=
H: Handlers=kbd event1
B: PROP=0
B: EV=3
B: KEY=10000000000000 0
I: Bus=0019 Vendor=0000 Product=0005 Version=0000
N: Name="Lid Switch"
P: Phys=PNP0C0D/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input4
U: Uniq=
H: Handlers=event2
B: PROP=0
B: EV=21
B: SW=1
I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button"
P: Phys=LNXPWRBN/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
U: Uniq=
H: Handlers=kbd event3
B: PROP=0
B: EV=3
B: KEY=10000000000000 0
I: Bus=0019 Vendor=0000 Product=0000 Version=0000
N: Name="Ideapad extra buttons"
P: Phys=ideapad/input0
S: Sysfs=/devices/platform/VPC2004:00/input/input6
U: Uniq=
H: Handlers=kbd rfkill event4
B: PROP=0
B: EV=13
B: KEY=1400800100c03 400000000300000 0 0
B: MSC=10
I: Bus=0010 Vendor=001f Product=0001 Version=0100
N: Name="PC Speaker"
P: Phys=isa0061/input0
S: Sysfs=/devices/platform/pcspkr/input/input7
U: Uniq=
H: Handlers=kbd event5
B: PROP=0
B: EV=40001
B: SND=6
I: Bus=0003 Vendor=13d3 Product=5170 Version=0730
N: Name="Lenovo EasyCamera"
P: Phys=usb-0000:00:14.0-4/button
S: Sysfs=/devices/pci0000:00/0000:00:14.0/usb3/3-4/3-4:1.0/input/input8
U: Uniq=
H: Handlers=kbd event6
B: PROP=0
B: EV=3
B: KEY=100000 0 0 0
I: Bus=0019 Vendor=0000 Product=0006 Version=0000
N: Name="Video Bus"
P: Phys=LNXVIDEO/video/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:35/LNXVIDEO:00/input/input9
U: Uniq=
H: Handlers=kbd event7
B: PROP=0
B: EV=3
B: KEY=3e000b00000000 0 0 0
I: Bus=0019 Vendor=0000 Product=0006 Version=0000
N: Name="Video Bus"
P: Phys=LNXVIDEO/video/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:03/input/input10
U: Uniq=
H: Handlers=kbd event8
B: PROP=0
B: EV=3
B: KEY=3e000b00000000 0 0 0
I: Bus=0001 Vendor=10ec Product=0269 Version=0001
N: Name="HDA Digital PCBeep"
P: Phys=card0/codec#0/beep0
S: Sysfs=/devices/pci0000:00/0000:00:1b.0/sound/card0/hdaudioC0D0/input11
U: Uniq=
H: Handlers=kbd event9
B: PROP=0
B: EV=40001
B: SND=6
I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH Mic"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1b.0/sound/card0/input12
U: Uniq=
H: Handlers=event10
B: PROP=0
B: EV=21
B: SW=10
I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH Headphone"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1b.0/sound/card0/input13
U: Uniq=
H: Handlers=event11
B: PROP=0
B: EV=21
B: SW=4
I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name="HDA Intel PCH HDMI/DP,pcm=3"
P: Phys=ALSA
S: Sysfs=/devices/pci0000:00/0000:00:1b.0/sound/card0/input14
U: Uniq=
H: Handlers=event12
B: PROP=0
B: EV=21
B: SW=140
Last edited by kYd (2014-07-01 18:11:45)

Hi gav989,
welcome to the forums. Please have a look at our forum etiquette, esp. at the "Pasting Pictures and Code" section.
The image you posted is too big, but only slightly, so I leave it there for now. You may want to look at these screenshot posting rules as well.

Pendrive not detecting and not showing files/folders after injecting pendrive into PC !

sir, tell me where i can solve problem of detecting of FLASH DRIVE USB3.0 of model no:v210w that have been purchased from nagpur and currently not detecting and may have so many VIRUSES in that PENdrive. suggest service center to retieve data of PENDRIVE

johnboy922,
Which region did you call into The call center for North and South America is here in Stillwater, OK. While there are some varied accents around here from southern to northern, this OKIE has never had any trouble understanding them.
Daniel

Hp Pavilion DV4-1235ee No sound & Usb port not detecting.

In my laptop Hp Pavilion dv4-1235ee there is no sound coming from the internal speakers. If I connect external speaker its works fine. Usb port is not detecting now. any help will be appreciated.

What is the current Operating system on your notebook? I suspect we have issue with internal speaker on hand...but would like to reinstall the Audio Driver and check...
Again for the USB, we can try and install Chipset driver and check...
Although I am an HP employee, I am speaking for myself and not for HP.
Make it easier for other people to find solutions, by marking my answer with 'Accept as Solution', if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"

Hp 16 gb pendrive not detected in car stereo system.

hi sir,
i have purchase hp pendrive 16 gb it is working in computer but not detected by the car stereo system please provide the solution.

There could be a couple of reasons why its not working for your car stereo.
Look up the manual for your stereo. Several have a size limit as to what they will accept.
Example: It will read up to an 8 GB drive.
Also make sure you have the right music file type it will read.
Usually, Stereos will read FAT32 and not NTFS. Make sure you have it formated correctly.
Worst case scenario I have seen is that some model stereos will not read every brand USB drive.
The manufacturer may have a list of approved drives.
Hope it helps.

[Solved] Hard Disk not detected

Currently i am using 4 hard drives and out of which 2 hard drives are detected and 2 are not. The fasinating thing is that in BIOS all the 4 hard drivers are detected and using a live cd i can access all the 4 drives without any prob. All the 4 drivers are working properly in windows7. It's just in arch linux 2 of my drives are not detected.
Recently i have upgraded my system from kernel 3.6.9 to 3.6.10
the drives are SATA drives. they are connected directly to the motheboard using SATA cables. the live cd i used was Ubuntu. I checked in /sys/block/ and with lsblk. In both of them i can see 2 drives sda and sdb.
Even check the dmesg, but there was nothing related to sdc or sdd. even on boot there were no errors.
They are NTFS formatted and always the 2 same disks are detected.
pls guide me as i am really freaked off due to this prob.
Last edited by creative2innovative (2012-12-26 05:37:55)

ewaller wrote:
How about rebooting, and then posting the output of dmesg. It will be long, so be sure to use BBCode 'code' tags. Alternately, install wgetpaste; pipe the output of dmesg through wgetpaste, and post the link wgetpaste provides here.
Edit: Never mind I see you updated with solved while I was posting. But what is the solution?
Thanks ewaller for the reply The prob was that, the capacity of my SMPS ( power unit ) was not sufficient to run 4 HDD + printer + 2 TB external drive. So this was the main reason. When i disconnected the printer and the external drive again all the 4 HDD were detected in my arch machine

Phone USB disconnect not detected

On my one PC, PC Suite does not detect when I disconnect my E51 phone from the USB cable in PC Sync mode.
This one happens on this specific PC, so it must be a setup problem there.
I am running PC suite 6.85.14.1 on WinXP SP2 patched up to date. No problem on another box with same motherboard and software using the same phone.
If I connect in data transfer mode, I use the "safely remove hardware" function of WinXP before I disconnect and all is fine. This is not available in PC Suite mode.
If I unplug the cable from the phone in PC suite mode, PC Suite does not detect that the phone is disconnected, no matter how long I wait.
After this, the whole USB system seems to be confused. No other USB devices are detected when plugged into any other USB port. After reboot all is fine again.
I guess this is a Windows problem rather than a PC suite problem.
Any idea what is going wrong and how to correct this?

i had other similar problem with usb devices, maybe when we use more usb devices could be a conflict on system, does exist a tool that clean up all old usb connection?
bye.

Pendrive not detecting

i have purchased and usb flash drive last 15 days ago from Grant road and it was working properly but all of a sudden it is not showing on my laptop & in disk management its showing no Media pls help me out...

Subani,
You will want to try the pen drive on another computer to test with.
If the drive is still not detected on any other computer, then it is a bad drive and needs to be replaced.
Let me know what you find.
Thanks.

X220: external USB keyboard not detected in BIOS

Hi!
I use an external USB keyboard attached to the port replicator of my X220. When Windows is booted the keyboard works without any problems. But I cannot use the keyboard pre-boot, e.g. to enter the HDD password after starting up, to configure the BIOS, etc.
I tried all USB ports both of the port replicator and the X220. The keyboard is still not detected by the BIOS (Version 1.20) and there are no BIOS options to enable "USB keyboard support".
Has anyone experienced similar problems? Are there any solutions to get the keyboard detected by the BIOS?
Thank you for your support!

@beastiesoft and earthartja,
If I am not mistaken, we are discussing this on the T series thread. Check here.
http://forums.lenovo.com/t5/T400-T500-and-newer-T-series/T420-Not-recognizing-keyboard-before-OS-loa...
@someotherguy,
Drop you an email on this.
//JameZ
Check out the Community Knowledge Base for hints and tips.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
X240 | 8GB RAM | 512GB Samsung SSD

USB Port not detecting device

My usb port on the side of the pc both are not detecting any device. How to fix it?

A good place to start troubleshooting is this HP document, Troubleshooting USB Connections (Windows 7).
If you don't have Windows 7 or if you have further problems, please to provide more information when you post again. The more information you provide, the more likely it is that you'll find someone here to help you.
Welcome to the forum,
GeorgeFN
GeorgeFN
I work on behalf of HP.

[FINALLY SOLVED] "Audio device not detected by EAX Console/Speaker Setting Panel" Prob

PROBLEM: A message pops up saying "The audio device supported by this application is not detected" when clicking on any Creative Utilities like EAX Console or the Speakers Control Panel.
SOLUTION: After 6 hours of trying out all solution advices/attempts for the problem above, I figured that there are only 2 ways to get rid of this issue.
[color="#ff0000"]st way: Kill your whole system, by doing format C:
[color="#800000">2nd way: Follow this advice from Shag:
[color="#800000">?
[color="#800000">An installation error causes this problem which in the first instance is addressed by ensuring that you have disabled the onboard audio. If this does not work in the second instance you will need to uninstall the card as follows:
() Uninstall software and drivers either, through control panel or the installation CD
(2) Move the card to PCI slot 3 (if not already there) [VERY IMPORTANT]
[color="#800000">?
[color="#800000">(3) Manually remove registry entries as follows:
. Delete the files from "\Creative".
2. Delete the following registry node from the registry
- HKLM\Software\Creative Tech\Software Installed
- HKLM\SOFTWARE\Microsoft\Windows\CurrentVersion\Uni nstall\5CDDF96A-BC34-4D72-9ABA-EFFF0C39977
(4) Reinstall the software and drivers.
Eventually I'd like to recommend the Creative Team to put this solution in the FAQ, since I counted at least 20 members in this forum, having the same problem without getting to a solution.
Cheers,
Diabolius

BTW just in case people search for the error message in German:
in German the pop up says:
"Das von dieser Anwendung unterst?tzte Audioger?t wurde nicht gefunden"

[Solved]Usb Pendrive not detected

Similar Messages

Maybe you are looking for