Sup32 from CATOS to IOS

I am about to begin a conversion from CATOS to IOS. I was wondering if I could do the following:
1: Use a new flash card, and format it in an NATIVE IOS Sup720
2: Put the correct code and configuration on it
3: Put it in the Sup32 and rebooted it
Would this then allow the Sup32 to boot up using IOS and not CATOS. I know I may have to copy the configuration from the flash to NVRAM but it seems like the quickest process, instead of the 30 minutes based on CCO documentation.
Thanks

I actually just tried this and it workerd. I took a sup32 that was running CATOS. Put in a CF card that was formated in a SUP720 with the IOS image on it. Replaced the on-board CF card with the new one. The system booted and couldn't find and files. I put the boot variable in ROMMON mode and bam up and running. Just had to change the bootvar in IOS and create the new config. Much faster than doing two copies of a 76MB file.

Similar Messages

Convert Qos commands from CATOS to IOS

Hello,
i've some problems converting some Qos commands from CATos to IOS can anybody help me?
set qos drop-threshold 1q4t rx queue 1 50 60 80 100
set qos map 2q2t tx 1 1 cos 0
set qos map 1p1q4t rx 1 3 cos 4
set qos wrr 1p2q2t 50 255
set qos txq-ratio 1p2q2t 70 15 15
set qos wred 1p2q2t tx queue 1 70:100 70:100
set qos bridged-microflow-policing disable 1,50-54,100-121,500,700-702,1006-1011,1016
set qos policed-dscp-map 1:1
set qos policed-dscp-map excess-rate 0:0
set qos acl default-action ip dscp 0
set qos acl default-action ipx
set qos acl default-action mac
set qos policy-source local
set qos rsvp disable
set qos rsvp policy-timeout 30
set qos rsvp local-policy forward
!Module with GE interfaces
set port qos 3/1-16 cos 0
set port qos 3/1-16 trust trust-cos
set port qos 3/1-16 port-based
set port qos 3/1-16 policy-source local
set qos statistics export port 3/1 disable
set qos statistics export port 3/2 disable
set qos statistics export port 3/3 disable
set qos statistics export port 3/4 disable
set qos statistics export port 3/5 disable
set qos statistics export port 3/6 disable
set qos statistics export port 3/7 disable
set qos statistics export port 3/8 disable
set qos statistics export port 3/9 disable
set qos statistics export port 3/10 disable
set qos statistics export port 3/11 disable
set qos statistics export port 3/12 disable
set qos statistics export port 3/13 disable
set qos statistics export port 3/14 disable
set qos statistics export port 3/15 disable
set qos statistics export port 3/16 disable

This URL should help you:
http://www.cisco.com/warp/public/473/73.html

6509 conversion from CatOS to IOS

I am interested in hearing from those who have converted from CatOS to IOS using 6500 as primarily a LAN switch with InterVLAN routing. Are there valid reasons / advantages to running IOS over CatOS? It seems to me that the CatOS is more efficient language for configuring switch ports and the IOS is better for configuring routing. I use 6509 in the core for server farms mostly and with the integration of many IOS based switches (3750) I am considering migrating the 6509 to IOS as well.
Thanks,
Greg

Greg,
Cisco may support CATOS for a while, but I do think that they may end of life it in the future. Thats why there is a big push on the IOS over CATOS.
I feel that the IOS is equally efficient in configuring switch ports as CATOS. You can use interface range commands to configure common parameters to a range of switch ports. And the great thing about configuring switchports in IOS is that it will have the same syntax like your 3750 switches.
Here is a link that compares commands on both switches which will help a lot after migration.
http://www.cisco.com/en/US/products/hw/switches/ps700/products_tech_note09186a008010e9d5.shtml
Sankar
PS: please rate helpful posts!

Catalyst 5505 conversion from CatOS to IOS

I want to know if somebody has the CatOS to IOS conversion procedure for a Catalyst 5505.
Thank´s a lot
Jorge

The Cat 5000s always run only CATOS. Only the L3 module supports IOS.Only the sup engines on the6500 and7600 support theconversion from CATOS toIOS.

Catalyst 6509 Conversion from CatOS to IOS.

Hi,
I am converting a Cat6509 Sup720 CatOS to IOS.The switch also has a FWSM configured. During converting CatOS to IOS will the FWSM configuration be erased or affected by any means ?
Regards
Kas

there should be no affect or deletion/problems with the FWSM during your IOS conversion.
haven't seen any issues in my LAB. the conversion process has a part where the CatOS commands/config are converted to the IOS commands/config required.
you should make sure you backup the FWSM configuration and partitions before you begin.
please see the following link for the CatOS to IOS conversion tasks for the sup720:
http://www.cisco.com/en/US/products/hw/switches/ps708/products_tech_note09186a008015bfa6.shtml#conv_720

CatOS to IOS conversion without RP

We have a Cat 6509 with a WS-SUP32-GE-3B and want to convert the CatOS to IOS. We need to know if we can do the conversion, since we don't have a Route Processor implemented on the switch infrastructure. This environment consists of pure layer 2 switches with stand alone switch processors and no routing capabilities. Everything we've read shows navigating into the RP to load the new image. Would we be capable of converting to IOS in this instance?
Thanks for any help..

I am not at the remote site, but this is the show module for the CAT 6509:
Here's the list of modules within the chassis:
Mod Slot Ports Module-Type Model Sub Status
1 1 48 10/100/1000BaseT Ethernet WS-X6148A-GE-TX no ok
2 2 48 10/100/1000BaseT Ethernet WS-X6148A-GE-TX no ok
3 3 48 10/100/1000BaseT Ethernet WS-X6148A-GE-TX no ok
4 4 48 10/100/1000BaseT Ethernet WS-X6148A-GE-TX no ok
5 5 9 1000BaseX Supervisor WS-SUP32-GE-3B yes ok
6 6 48 10/100/1000BaseT Ethernet WS-X6148A-GE-TX no ok

CatOS to IOS Converter tool

Hi,
Does anybody have any experience of using the CatOS to IOS Converter tool on a Sup720?
Just to be clear, I'm not referring to the Configuration conversion tool but to the actual OS conversion tool. The CCO document (http://www.cisco.com/en/US/products/hw/switches/ps708/products_tech_note09186a008070f124.shtml)
indicates the tool was tested on a Sup2 only but i was wondering if it could be used with the Sup720's as well?
If not i assume everyone would suggest the manual method as the preferred method of converting from Hybrid to Native?
Thanks

Cisco Software Config. Tools for Cat6000:
http://www.cisco.com/cgi-bin/tablebuild.pl/cat6000-config-converter

Cannot send or receive yahoo mail or gmail from iPhone . installed ios 6 recently. tried rebooting the phone and deleting the email account and adding again but nothing works ! can someone suggest a solution?

cannot send or receive yahoo mail or gmail from iPhone . installed ios 6 recently. tried rebooting the phone and deleting the email account and adding again but nothing works ! can someone suggest a solution?

Not sure about yahoo, but for gmail, I done the following:
Set up using Exchange on iPhone, it'll keep prompting for password. On PC use captcha option, log in to gmail account from PC after completingg captcha option, enter password on iPhone.
See how that goes for gmail, let us know.
Hopefully someone will have fix for yahoo.

I updated my iPod touch 4th generation from the latest iOS 4 update (i think maybe iOS 4.3.5 or something like that) to iOS 5.1.1 and my Photos, Videos, contacts, music, App data, etc. was deleted. How can I all the data back?

I updated my iPod touch 4th generation from the latest iOS 4 update (i think maybe iOS 4.3.5 or something like that) to iOS 5.1.1. I updated to iOS 5.1.1 on a Windows XP Home Edition with the Service Pack 3 installed on the Windows XP (which I believe is the latest version). After updating, I unplugged my iPod from the computer. I saw that all my photos and videos were on my iPod, but there were no apps. A window popped up and told me to enter a passcode for my iPod. I entered a passcode. I then locked my iPod and entered what I thought to be the correct passcode, but my iPod remained unlocked. Desperate, I tried many passcodes with failure. After a while, my iPod became disabled for a long time. I decided to reset my iPod. After I reseted it, I chose to reset from my earlier back up. After reseting, my computer loaded on all my apps. But, when I started using my iPod, I realized all my photos, videos, music, app data (like game saves and high scores), etc. were gone! I have no idea what to do and I am very stressed about this! SOMEONE PLEASE HELP ME GET ALL MY STUFF BACK!!!!!!

Go to iTunea>Preferences>Devices and see if there is a backupright at the time you did the update. Then try restoring from that backup. If the apps are in your iTunes library, any app data will be restored to the iPod.
When restoring from an iOS 4 (or later) backup, if the device had a passcode set, iTunes will ask if you want to set a passcode (and remind you that you had protected your device with a passcode). iTunes will not ask you to set a passcode when restoring from iOS 3.x and prior backups.
Therefore, remembe the passcode that you enter this time.
It appears that if you restore from a backup, that backup is not subseqyently overwritten by the next backup.

How do I make it so iWork docs don't have to reformat from Mac to iOS

How do I make it so iWork docs don't have to reformat from Mac to iOS?
When I edit docs and spreadsheets on my Mac with OSX Mountain Lion with documents in iCloud, they have to be reformatted when I go to open them on my iPad or iPhone. This is minor annoyance but an annoyance nonetheless. Is there a way to format docs on the Mac so this does not take place?

Hello KatTreeRain,
And welcome to Apple Discussions!
Change the music video's *Media Type* to Video. To do this, right->click on the music video and choose *Get Info* and then head over to the Options tab. There you will see the *Media Type* option with a drop down list. This will move the music video to your Videos/Movies.
B-rock

Can I use an iTunes gift card to order a photo book from iPhoto for iOS?

Can I use an iTunes gift card to order a photo book from iPhoto for iOS?

no - credit card or debit card only unless they have recently changed their policy
LN

I downgrad my iphone from ios5 to ios 4.3.3 and after restoring the ios 4.3.3 i fixed all itunes error but after that my i phone screen turned off and the apple logo didnt shows up any more what ever i did my iphone model 4 gsm

i downgrad my iphone from ios5 to ios 4.3.3 and after restoring the ios 4.3.3 i fixed all itunes error but after that my i phone screen turned off and the apple logo didnt shows up any more what ever i did my iphone model 4 gsm and fyi i try all the ways to turn it on but it didnt sucsses

roaminggnome
thanks for helping but i didnt know that is the downgrade is forbidden and i ask for help and u didnt help me so i just want to thank u for telling me that is the downgrade is forbidden >>> but now i didnt have i phone any more so thank u so much again >>>>

Just upgraded iPhone 4 from 4.2 ios to 6.1.3 ios now can't connect to internet

I just updated my friend's iPhone 4 from 4.2 ios to 6.1.3 ios -- she had not updated it since she purchased it. The uploads installed fine but now she can't access safari/internet and can't send pictures via text message. She is strictly 3g with no wireless access at her home. Could this be caused by the software upgrade? If not, how/where do I start looking for the problem.
Any help will be greatly appreciated.
chuswysly♥

Hi chuswysly,
If your friend if having trouble connecting to her cellular network, the steps below might help:
iPhone: Troubleshooting a cellular data connection
Resolution
Follow the instructions below for assistance with troubleshooting cellular data issues on your iPhone. After performing each step, please test to see if the issue is resolved.
Toggle cellular data off and then on again on the iPhone: Tap Settings > General > Cellular.
Restart your iPhone.
Check for a carrier settings update.
Update your iPhone.
Remove the SIM Card and reinsert it. Allow the iPhone to reaquire the network.
If your SIM card has SIM PIN enabled, try toggling it off: Tap Settings > Phone > SIM PIN.
Try another location. If a different location works, but the original location still does not, contact your carrier to report the issue.
Reset network settings: Tap Settings > General > Reset > Reset Network Settings.
Restore the iPhone as new.
Contact your carrier to verify that the iPhone is properly set up on the account with the appropriate, current data plan. If you are traveling internationally, you may need to turn data roaming on: Tap Settings > General > Cellular. Check with your carrier first to understand the cost of international data roaming. Also, see this article.
Note: If your carrier does not appear in this list, verify with your carrier that you are using the correct cellular data settings.
If none of the above steps resolves the issue, contact your carrier, make an appointment at an Apple Retail Store, or contact AppleCare to troubleshoot further.
Hope this helps ...
- Judy

Replacement iphone - trying to restore from backup, but iOS v 6 running and won't update from recent backup

Replacement iphone - trying to restore from backup, but iOS v 6 running and won't update from recent backup. How do I ensure I get all my photos etc onto new phone?
Thanks

If you're old phone that was repalced was a higher version of iOS, it wont be able to restore. Update your iPhone to the lastest iOS 7.0.4 and try to restore it then.

How to open Adobe Reader file from another native IOS application?

There is an existing thread, but I want to re-open it because I think this is an important feature that we need badly. I was wondering if there is any plan to add this feature so we can open PDFs directly into Adobe from the web / other apps.
How to open Adobe Reader file from another native IOS application?
Basically, we just want to use a custom URL scheme to open a specific document in the App. Currently, this only opens the app but does not load the file.
APB

Not to hijack the conversation but I can explain why this would be useful for both the above case and another.
What I believe Pavel is talking about is setting up a "URL Scheme" for the Adobe Acrobat iOS application so that you can easily open a PDF specifically in Adobe Acrobat iOS from other native applications and even from web applications opened within Safari. This is particularly useful if your application requires some of the specific features in Adobe Reader iOS to grant them the best experience possible and you want to encourage this.
Another case: If you're using Adobe Livecycle's document security modules (that encrypts PDF files so that Adobe Acrobat must "phone home" to decrypt and view the document), these PDF's can only be viewed inside the Adobe Acrobat application and appear as blank in most other PDF readers. Having a URL scheme allows your application utilising this functionality to have a 1 click step to view the PDF rather than the current non-user friendly process:
- Within Safari, touch the PDF link (appears as blank in the default Safari PDF reader, which in itself is confusing)
- Touch "Open in..."
- Touch "Adobe Acrobat"
We have an immediate need for this functionality for the example above. I can resubmit it in a separate post if necessary.

Sup32 from CATOS to IOS

Similar Messages

Maybe you are looking for