Unity Connection 8.5 - No Diversion Header information in transfered call

We are having call failures when calls are transfered to our SIP provider from Unity Connection (AutoAttendent). We have tracked this down to Unity is sending a Refer that does not have any information regarding the number the call was transfered from. Subsequently Callmanager does not create a diversion header in the invite to the SIP provider.
The SIP provider require either a authorized number in the from header or a the same in the diversion header.
We have the rediversion headers enabled on the callmanager side of the trunk.
Does anyone have end to end SIP configuration with UCM 8.5 and Unity Connection 8.5 and can complete transfers back to the provider?
mike

I don't see any problem, just don't check the option to ignore additional input when configuring caller input on digit 1
By default CUC will give you 1500 ms to dial for any other digits before trying to route the call with whatever you dialed.
HTH
java
if this helps, please rate
www.cisco.com/go/pdihelpdesk

Similar Messages

Unity Connection - Certificate from cucm no more trusted for encrypted calls after upgrade to 10.5(1)

Hello Support Community,
i have a strange problem:
after upgrading my cucm and unity connection from 9.1 to 10.5(1) enctrypted calls are no more working.
situation 1: CUCM is down, Subscriber is up: Encrypted call to Unity Connection work correctly
situation 2: CUCM is up: Encrypted Calls to Unity Connection not working.
i get the following Info in the log for the Connection Conversion Manager:
19:35:21.053 |15865,,,MiuGeneral,25,Invalid Certificate: Received Certificate -----BEGIN CERTIFICATE-----
MIID8zCCAtugAwIBAgIQc/fBdUz1Zdh4CXhcPqGVuDANBgkqhkiG9w0BAQsFADBw
MQswCQYDVQQGEwJERTELMAkGA1UEChMCSVQxGzAZBgNVBAsTEkhlbGxnYXRlIFRl
XD0oD9d5MQ==
-----END CERTIFICATE-----
doesn't match with stored Certificate: -----BEGIN CERTIFICATE-----
MIIC2DCCAkGgAwIBAgIIJWCm4bSdt+kwDQYJKoZIhvcNAQEFBQAw
-----END CERTIFICATE-----
so where does Unity Connection cache this certificate and how can i delete/replace it?
the cert shown in the logs is the one from cucm: ("CallManager"), i recreated it through cucm os administration, now i see the same error message on unity connection for the new recreated certificate.

Actually It doesn't. It says he's on a MacBook. I don't know all the different types of Macs. I was having a ton of problems with iChat. I opened DMZ to my computer, knocked down all firewalls etc and left everything exposed, still with bad results. A few weeks ago my power supply went out on my D-Link. I bought a linksys. Since I'd left all firewalls off I figured it couldn't be the router. I power cycled everything n the netork, still no luck. Today I bought a universal Power supply and started up my D-Link Router. Everything worked perfectly. My wifes computer - a laptop running Tiger worked fine with the Linksys and did my machine before the Leopard upgrade. Now that I've got the D-Link online everythings working.
Message was edited by: graphico
Message was edited by: graphico

Cisco Unity Connection 8.6 not getting CLID information from CUCM 8.6

Hello,
Currently Running:
Cisco Unified Communications Manager 8.6.2
Cisco Unity Connection 8.6.2
Problem:
when any outside caller leaves a voicemail, the caller number information is not being sent to unity.
example, I call with my cell phone, 817.555.1234 to my Cisco 7940 phone and it shows the CLID information that i am calling with. iDivert to voice mail, Leave a message. Playback message and just the default message information from Cisco Unity.
we currently upgraded from CUCM 6.1.3 and Unity 5. before i could press 9 and get the caller information.
I have viewed the "Playback Message Settings" and selected "After Playing Each Message, Play" and selected Sender's Information. and also selected "Include Extension and Sender's ANI"
upon playing the VoiceMail after the message i get the default message "From Cisco Unity Connection Messaging System"
I also have the message relaying to my E-mail and I get the same in the subject line.
"Message from Cisco Unity Connection Messaging System (Unknown extension)"
This tends to be a big deal with the Sales team as customers will call and say "Call me back"
But any Internal Calls show the correct information, proper greeting, extension information even on the relay to e-mail.
Any help will be appreciated.
Thanks
Tim

Found another post that referenced Cisco Bug ID CSCti37610.
CUC plays message is from Unity Connection Messaging system
Symptom:Before message playback, Unity Connection plays the message is from Unity Connection Messaging System instead sender's ANI
Conditions:Problem was observed on Unity Connection cluster and appropriate services are not rebooted after changing the SMTP domain name
Workaround:
Restart the Unity Connection servers
It should have been fixed in 8.5 but we did change the SMTP domain name on 8.6 and now see the problem. Will schedule a reboot and see if the issue goes away.

Unity Connections 7.x Unable to route to Contacts from Call Handler

Unity Connection 7.x. CallManager 7.x.
My desired goal is to route from an AutoAttendant CallHandler to CallManager users that do not have VoiceMail boxes. I have created a contact with the following:
alias: myuser
first: my
last: user
display: my user
voice name: recorded
list in directory: yes
transfer enabled: yes
transfer extension: 1234
When dialing AA and pressing # to get the the directory and doing dial-by-name, I am able to route. When dialing the extension number during the greeting, I receive the following:
"I did not recognise that as a valid entry"
When selecting "Allow Transfers to Numbers Not Associated with Users or Call Handlers" from within the AA Handler and then dialing by extension, I receive the following:
"You cannot be transferred to this number"
Is there a way to dial the extension number to get to the user's device?
Regards...

Hi Phil Denton,
You are indeed going on the right track with the
"Allow Transfers to Numbers Not Associated with Users or Call Handlers"
What you're missing is the restriction table which by default doesn't allow any patterns to be dialed.
So in the System Settings go to the Restriction Tables and select the "Default System Transfer", and add a pattern that matches your internal extension or just that specific one.
Now this will permit dialing by extension to those specific patterns, one last thing you should verify is that the CSS assigned to your voicemail ports in UCM has the proper partitions to dial those extension.
HTH
Jonathan Sylvain
Message was edited by: Jonathan Sylvain My bad didn't notice original past was in 2010

Unity Connection 8.6 call transfer to non-unity extension

I have converted from Unity to Unity Connection and am looking for a solution for transferring an incoming call to a non-unity user extension.
Here is the scenario: An PSTN caller calls in and is directed to a Unity Connection Call Handler or a Subscriber greeting. In the greeting they are advised that if they know the extension they want to call, they can dial it at any time. Here is the rub, if they dial an extension for a user listed in Unity Connection, the call gets transferred to the extension. However, if the extension dialed is to an extension that is not a Unity Connection User, the attendant comes back and say the extension is not understood.
In Unity before conversion, I would make an internet user that did not have a mailbox but was listed with an extension. However, with Unity Connection, I am using LDAP integration with Microsoft AD and I don't see a method of doing the same thing.
Is anyone else doing something like this or know of a method to do it?
Thanks in advance.
Gene Keel

In the greeting check this box:
Allow Transfers to Numbers Not Associated with Users or Call Handlers
also make sure the number entered by the call is allowed in Default System Transfer restriction table.

Scripts in Unity Connection

Hi,
I have a Cisco CallManager 8.6 and a Cisco Unity Connection 8.6 on VMWare.I purchased the bundle (solution) Cisco BE 6000.
I did the integration of the Unity Connection with the CUCM via SIP (I also created a trunk SIP on CUCM to access CUC).
I would like to use the Unity Connection as AutoAttendant.
My question is this:
In Unity Connection, could I make scripts like I do in Cisco Unity Express with the CUE Editor?
I want to use the Unity Connection as AutoAttendant as follows:
- The incoming call goes to a Extension of Attendant Console. If the call is queued for 15 seconds the call is forwarded to Greeting of AutoAttendant Unity Connection saying "you will be attended shortly, please wait"
- After Greeting the call is again transfered to the Extension of Attendant Console. If the extension is available the call is answered but if the call is again queued for 15 the call is again forwarded to the Greeting of AutoAttendant Unity Connection saying "you will be attended shortly, please wait"
- After Greeting when the call is transfered to the Extension of Attendant Console.If the call continues queued for another 15 seconds the call is transfered to another Greeting of AutoAtendant Unity Connection saying "we apologize for the incovenience. Please call back in a few minutes"
In Unity Connection, could I make scripts like I do in Cisco Unity Express with the CUE Editor?
The only way I know to do this is with the CUE Editor or CCX Editor (Contact Center Express).
Is there any way to do this with the Unity Connection?
Thanks

No scripting or queueing with Unity Connection. With BE 6000, you would need to leverage UCCX.
Hailey
Please rate helpful posts!

Unity Connection Transfer calls across ICT

I am working on a system where they have a unity connection 8.6(2) server that has a system call handler configured for external voice mail access. They would like to be able to have the users call in and enter the extensions of users on a remore CUCM cluster and be routed across the Inter Cluster trunk to the remote cluster. I have the system setup to allow the caller to enter the extension of users not associated with a mailbox and I have configured the transfer rules to allow the pattern defined for the extensions. However it still fails.
Any help would be greatly appreciated.
Thanks,
Michael

Michael,
Ensure the CSS assigned of the SIP trunk (if using UCXN SIP integration) or voicemail ports (if using SCCP) has access to a partition that the route pattern pointing to remote cluster is assigned to.
HTH,
Chris

Re: Passing HTTP Header Information

I am calling a web service ( using generated client stubs)
Is it possible to share HTTP header information to this call ?
Sample code is :
SimpleTestSoap echoPort = SimpleTest_Impl().getSimpleTestSoap();
String test = echoPort.xxxxMethos();
How do I pass an array of cookies(from the request object ) to this call ?
Thanks

I am calling a web service ( using generated client stubs)
Is it possible to share HTTP header information to this call ?
Sample code is :
SimpleTestSoap echoPort = SimpleTest_Impl().getSimpleTestSoap();
String test = echoPort.xxxxMethos();
How do I pass an array of cookies(from the request object ) to this call ?
Thanks

I keep getting a message "safari cannot open page [page name with header information] because you are not connected to the internet.

I keep getting a message "safari cannot open page [page name with header information] because you are not connected to the internet. Then I check CNN for a time stamp, and I am connected to the internet. I have reset everything suggested in other posts, ensured any other device that could be hogging bandwidth is off, the router is reset, the iPad is reset. The other devices are not having this problem, and it happens on both places I use the iPad, the university library, (getting a second degree after a change in a long time career and at home. Any insight into this issue would be appreciated.

Saing yu tried everthing provides little information to us. We do not know what you tied.
Have you tried:
- Resetting the iPod:
Reset iPod touch: Press and hold the On/Off Sleep/Wake button and the Home
button at the same time for at least ten seconds, until the Apple logo appears.
- Powering off and then back on your router- Resetting network setting: Settings>General>Reset>Reset Network Settings
The toubleshooting here:
iPhone and iPod touch: Troubleshooting Wi-Fi networks and connections
- Does you iPod conenct to other networks?
- Do other devices connect to your network?

Issue with transferring calls to VM for the correct DN Unity Connection 9.1.2

Hi all
I have been facing an issue with a Unity Connection Server v9.1.2. Every time an internal extension (assigned to VM profile and to Unity as a user) which is configured to be transferred to VM after 20 sec or so NoAN,is called , Unity treats the call as the extension of the calling party and not the called party. Furthermore , I dont know if this has any relation with the problem I am facing but when I check the voicemail port status in RTMT its seems like that regardless it is a direct call to the Unity from an extension (dial the pilot number or press the messages button on the IP phone) or a redirected call from an extension to Unity due to NoAN configuration, the Reason is Direct and the caller party number is always the extension initiated the call and not the one redirected to the Unity (second case).
I have changed the Use Last (Rather than First) Redirecting Number for Routing Incoming Call Unity parameter in the
System Settings > Advanced >Conversations -> checked and
Redirecting Diversion Header Delivery - Outbound CUCM parameter ->checked
in the SIP Trunk configuration used for the integraton of the CUCM with Unity but none of those seem to address this issue. Is there any guidelines you can give me to overcome this issue?
The servers I am using are
CUCM v9.1.2 BE
CUC v9.1.2 BE
Thank You in Advance

Hello again,
The Voice Mail Box Mask was blank before. However I tried XXXX (I use 4-digit extension for the VM pilot) but this did not seem to fix anything to the system....Same situation as before. Any more suggestions?
Thank you

Mailbox Custom Settins in Unity Connection Version 8.6?

Is there a way to get a list of all users with Mailbox Custom Settins in Unity Connection Version 8.6?

Hi Ronald,
You'll want to check out this Tool from the great suite of Unity/Unity Connection Tools
Connection User Data Dump (CUDD) Tool
The Connection User Data Dump (CUDD) is a Windows-based remote database administration tool available on the Cisco Unity Tools website. CUDD allows you to export specific information about users to a file that can be viewed or imported into another application, such as a database utility or Microsoft Excel. When the data is exported, the tool automatically creates a header row that lists the data type found in each column of the output, for ease of import into other programs.
The tool is available from the "Superb" Unity Tools site;
http://www.ciscounitytools.com/Applications/CxN/UserDataDump/UserDataDump.html
Cheers!
Rob
"Why do the best things always disappear "
- The Band

Unity Connection 8.5 Outcall notification to device too agressive?

I’ve noticed the Unity Connection 8.5 outcall notification is too aggressive. Is there a way to change the outcall parameters to wait x minutes between redials?
For example Connection called my cell phone, while I am inputting my PIN I get a second call from Connection alerting me to new messages. While I’m listening to the messages I get a third call from Connection. I noticed same problem if device is my desk 7962 phone.
Unity Connection 8x Administration Guide
http://www.cisco.com/en/US/docs/voice_ip_comm/connection/8x/administration/guide/8xcucsagpdf.pdf

Hi Jason,
These timers can be changed via the User or User Template pages
User Templates New Notification Device
Revised November 16, 2010
Table 3-21 User Template New Notification Device Page
Field Description
Notification Device Type
Select a type of notification device from the list.
Display Name
Enter a descriptive name for the notification device.
Phone Number
(Applicable only to phone and pager notification devices.) Enter the phone number, including trunk access code, of the selected device. Use digits 0 through 9 and the following dialing characters in the phone number:
•, (comma) to insert a one-second pause.
•# and * to correspond to the # and * keys on the phone.
Users can change this number by phone.
Extra Digits
(Applicable only to phone and pager notification devices.) Enter any extra digits that Cisco Unity Connection dials after the phone number. The effect of the extra digits depends on the selected device. For pagers, the extra digits are shown on the pager display.
For example, the extra digits could be used to include a callback number when sending notifications to numeric pager devices. Extra digits can also be used to reach an extension, where the notification is configured to dial a public 800 access number and the extra digits would be sent at the opening greeting in order to reach the target extension.
Duration to Wait Before Dialing Extra Digits
(Applicable only to phone and pager notification devices.) Cisco Unity Connection can wait a specified number of seconds before dialing the digits in Extra Digits. Use this option if the automatic call progress detection is not reliable (for example, when phone lines are noisy or when ringing patterns are unusual).
Rings to Wait
(Applicable only to phone and pager notification devices.) Enter the number of times that Cisco Unity Connection allows the user phone to ring before ending the attempt. The setting must be at least 3 rings. Enter a higher number to give a user more time to get to the phone.
Default setting: 4 rings.
Busy Retry Limit
(Applicable only to phone and pager notification devices.) Indicates the number of times that Cisco Unity Connection tries to reach a user number that is busy. Select a higher number to reach someone who uses the phone frequently.
Default setting: 4 times.
Busy Retry Interval
(Applicable only to phone and pager notification devices.) Indicates the number of minutes that Cisco Unity Connection waits between attempts to reach a user number that is busy. Select a higher number to reach someone who has long phone conversations.
Default setting: 5 minutes.
RNA Retry Limit
(Applicable only to phone and pager notification devices.) Indicates the number of times that Cisco Unity Connection tries to reach a user who does not answer the phone. Select a higher number to reach someone who steps away from the phone briefly. Select a lower number to avoid disturbing others.
Default setting: 4 times.
RNA Retry Interval
(Applicable only to phone and pager notification devices.) Indicates the number of minutes that Cisco Unity Connection waits between attempts to reach a user who does not answer the phone. Select a higher number to reach a user who is away from the phone for long periods of time.
Default setting: 15 minutes.
Retries After Successful Attempt
(Applicable only to pager notification devices.) Indicates the number of times that Cisco Unity Connection calls the pager device after the first successful call to the device while the message that triggered the notification is still marked new. Use this setting in conjunction with the Retry Interval After Successful Attempt setting if users need additional reminders of new messages, or if users sometimes do not receive notifications even though the first call to the pager is successful.
If set to a value greater than 0 (zero), Connection makes periodic calls based on the Retry Interval After Successful Attempt until the user checks the message or the retry limit is reached. For example, if Retries After Successful Attempt is set to 2 and Retry Interval After Successful Attempt is set to 15, and the user receives a new message at noon, Connection will call the pager device at noon. If that call is answered, but the user does not check the message before 12:15 pm, Connection calls the pager device again at 12:15 pm. If the user does not check the message before 12:30 pm, Connection calls the pager device a second time at 12:30 pm.
Note This setting generates a series of notifications that is separate from the series that is generated if you enable the Repeat Notification If There Are Still New Messages setting on the Edit Notification Device page. To avoid confusing the user with multiple repeating notifications, we recommend that you use either the Retries After Successful Attempt setting or the Repeat Notification If There Are Still New Messages setting, but not both.
Enter a value between 0 and 100. A value of 0 (zero) means that Connection does not retry the notification after the first successful call to the pager.
Default setting: 0.
Retry Interval After Successful Attempt
(Applicable only to pager notification devices.) Indicates the interval at which Cisco Unity Connection retries calling the pager device after the first successful call to the device if Retries After Successful Attempt is set to a value greater than 0 (zero) and the user has not yet checked the message. Use this setting in conjunction with the Retries After Successful Attempt setting if users need additional reminders of new messages, or if users sometimes do not receive notifications even though the first call to the pager is successful.
Enter a value between 0 and 100 minutes. A value of 0 (zero) means that Connection makes additional retries as soon as a port is available to dial the device.
Default setting: 1 minute.
Phone System
(Applicable to phone and pager notification devices only.) Select the phone system that the notification device uses.
Prompt for User ID on Notifications
(Applicable only to phone notification devices.) Indicate whether Cisco Unity Connection should prompt the user to enter a user ID. The user is always asked for a PIN. Users may prefer not to enter a user ID in order to shorten the time that it takes to sign in.
Note Use this setting with caution and only if the phone is never answered by anyone other than the user.
SMPP Provider
(Applicable only to SMS notification devices.) Select the applicable SMPP provider.
To
(Applicable only to SMTP and SMS notification devices.) Depending on whether you are setting up message notification for a text-compatible mobile phone or pager, or for SMS (SMPP) devices:
•For SMTP text message notifications, enter the email address of the user text pager, text-compatible mobile phone, or another email account (such as a home email address).
•For SMS (SMPP) text message notifications, enter the phone number of the SMS-compatible device. The format and the number that you enter depends on the SMPP Provider. The provider may require that you include international country codes, beginning with a plus sign and followed by the country code, area, city, or trunk code, and then the number for the device (for example, +12065551234). Do not start with a zero or the international dialing prefix. Do not include spaces, dashes, parentheses or other punctuation.
Up to 128 characters can be entered in this field.
From
(Applicable only to SMTP and SMS notification devices.) For text-compatible mobile phones or pagers, enter the phone number that the user calls to check messages, or enter alphanumeric text (as applicable) in this field. The From phone number appears in the last line of any SMTP notification. A user can press the Return Call button on many text-compatible mobile phones to dial the phone number. The mobile phone must support automatic callback in order to use this feature.
For SMS (SMPP) devices, what you enter in this field depends on the SMPP Provider:
•If the SMPP Provider requires a "source address" for the server sending the message, enter the IP address for the Cisco Unity Connection server.
•If the SMPP Provider does not require a "source address," enter the number that the user calls to check messages. The format and the number that you enter depends on the SMPP Provider. The provider may require that you include international country codes, beginning with a plus sign and followed by the country code, area, city, or trunk code, and then the number for the device (for example, +12065551234). Do not start with a zero or the international dialing prefix. Do not include spaces, dashes, parentheses or other punctuation.
Note Consider that some SMPP Providers replace the number that you enter in the From field with their own phone number. For an alternative method of including a call back number, try entering the number that the user calls to check messages in the Message Text field.
Up to 40 characters can be entered in this field.
Message Header
(Applicable only to SMTP notification devices.) Enter any text you want Connection to put into the header of the notification message. For example, you might enter a legal disclaimer that you want to be sent with every notification message.
Message Text
(Applicable only to SMTP and SMS notification devices.) Enter the text message that the user wants to receive in a text notification. For example, you might enter "Urgent message for Technical Support" for a user who is on call for the technical support department. Every time a message arrives that matches the criteria selected in the message notification settings, Cisco Unity Connection sends the text you enter here.
Note To include a call back number, try entering the number that the user calls to check messages within the message text (for example, enter the number in this format: tel:2065551212).
Up to 160 characters can be entered in this field. (For SMS devices, depending on the character set you configure Connection to use, it is possible that messages that are shorter than 160 characters may be truncated.)
Message Footer
(Applicable only to SMTP notification devices.) Enter any text you want Connection to put into the footer of the notification message. For example, you might enter a legal disclaimer that you want to be sent with every notification message.
Include Message Information in Message Text
(Applicable only to SMTP and SMS notification devices.) Check this check box to include information about the new message in the text string that is sent to the notification device. This information can include caller name and caller ID (if available); the type of message (voice, email, fax); the time that the message was received; and, if the message was marked private or urgent, an indication of this status.
Include Message Count in Message Text
(Applicable only to SMTP and SMS notification devices.) Check this check box if you want the notification to include a count of the number of new messages in the mailbox.
Include a Link to Cisco PCA in Message Text
(Applicable only to SMTP notification devices.) Check this check box to include a link to the Cisco Personal Communications Assistant in the text string that is sent to the SMTP notification device.
http://www.cisco.com/en/US/docs/voice_ip_comm/connection/8x/gui_reference/guide/8xcucgrg030.html#wp1082329
Cheers!
Rob

Unity Connection Voice Mail Only- NO MWI template

I am deploying a site with 8,000 mailboxes. 4,000 of those users are voice mail only without a telephone and will NOT require MWI.
I can manually remove the MWI setting from each mailbox, but I am looking at either a BATCH CSV setting or a TEMPLATE that I can turn OFF mwi when creating the users.
Any ideas?
TIA

Hi there,
This setting change is available via Bulk Edit
Bulk Edit> Messages> Disable MWI functionality for this user
Bulk Edit changed in 8.x from where it was accessed in 7.x.
Here's a clip that speaks to how this is run now. You first search and select all
the users you want to change and then choose Bulk Edit;
To Edit User Account Information in Bulk Edit Mode (some editing from original > this example
is for Caller Input settings but you'll see the point)
Step 1 In Cisco Unity Connection Administration, on the Search Users page, check the applicable user check boxes, and select Bulk Edit.
If the user accounts that you want to edit in bulk do not all appear on one Search page, check all applicable check boxes on the first page, then go to the next page and check all applicable check boxes, and so on, until you have selected all applicable users. Then select Bulk Edit.
Step 2 On the Edit Caller Input page, change settings as applicable.
Note The Status message at the top of the Edit Caller Input page tells you how many user accounts are being edited. Also note that the page is populated only with the fields that you are allowed to edit in bulk mode, and that the fields available for edit also depend on whether all of the user accounts reside on the local server.
Step 3 If applicable, set the Bulk Edit Task Scheduling Fields to schedule the Bulk Edit operation for a later date and/or time.
Step 4 Select Submit.
Step 5 If applicable, continue to change settings for these user accounts on the related pages available from the Edit menu. As you make changes on each page, select Submit before going on to the next page to make additional changes.
http://www.cisco.com/en/US/docs/voice_ip_comm/connection/8x/user_mac/guide/8xcucmac090.html#wp1049545
Try a couple of test users first to come up with the exact plan.
If you prefer you can also use Bulk Edit via .csv
As a test here I tried the Bulk Edit and chose;
User with Voicemail > Users referenced in this CSV file > Next
This then allowed me to browse to an existing "basic" .csv that I had
used to create a test user recently when playing with BAT. In this .csv
I had one user named Bob Uncle with DN/ext 5126. So when I used this method
the Bulk Edit tool (smart puppy ) selected only Bob Uncle for my edit choices
and I was able to change the Disable MWI functionality for this user
Again, please try manipulating some test users to perfect
your methodology.
I have attached the test .csv I used
Cheers!
Rob
Attachments: buncletest Mailboxes.csv.zip (255 bytes)
"Show a little faith, there's magic in the night" - Springsteen

Unity Connection 8.6.2 report error and issues

Hello,
I found some other hits on this error and tried the workarounds (restarting tomcat, and report data harvester) but am still getting "Unable to find any report data based on parameter(s)" for a certain timeframe on multiple reports when I know activity occurred in that timeframe.
User Phone login report, Outcall Billing Detail Report, others.
CUC version is 8.6.2.20000-2
Problem is during this timeframe someone dialed into system and changed the transfer extensions to various LD numbers throughout an entire day and the reports aren't showing these outcalls. Call Manager CDR data show the calls being placed from Unity VM ports and the Unity Conversation Manager traces I grabbed for the timeframe show the calls to those numbers to. I'm just trying to match up with a report and figure out if there is some other log or trace file I can look to determine for sure the caller logged in to the voicemail box and changed the transfer extension on it. (guessed the voicemaill password). The failed log in report doesn't even show the failed login attempt in output from traces below. The transfer extension dest addr was different on the transfers on this same mailbox. Have locked down the system since but want to get better grip on this with the reports and traces.
I looked over the CUC 8.6.2 SU1 and SU2 release notes and not seeing any resolved bugs for these matters either.
Here are some samples lines from Conversation Manager traces:
00:32:46.399 HDR|02/04/2013 ,Significant
00:32:46.399 |9744,PhoneSystem-1-001,E68CA6DB3CAE4118BE9F9612BD3540A9,Arbiter,-1,Incoming Call [callerID='' callerName='' calledID='555123' redirectingID='555123' lastRedirectingID='555123' reason=4=FwdNoAnswer lastReason=8=FwdUncond] port=PhoneSystem-1-001 portsInUse=1 ansPortsFree=23 callGuid=E68CA6DB3CAE4118BE9F9612BD3540A9
00:33:55.006 |9744,PhoneSystem-1-001,E68CA6DB3CAE4118BE9F9612BD3540A9,MiuGeneral,25,Enter CAvMiuCall::TransferEx destAddr='715551231234' type=2=Release maxRings=4 mediaSwitch='00a499fa-a193-45b0-a153-564a64019eb8'
00:33:58.955 |9744,PhoneSystem-1-001,E68CA6DB3CAE4118BE9F9612BD3540A9,MiuGeneral,25,Exit CAvMiuCall::TransferEx=0x00000000=S_OK
00:34:37.090 |9832,PhoneSystem-1-001,9DB394E443A3419FA0020BC9D1A92806,Arbiter,-1,Incoming Call [callerID='' callerName='' calledID='555123' redirectingID='555123' lastRedirectingID='555123' reason=4=FwdNoAnswer lastReason=8=FwdUncond] port=PhoneSystem-1-001 portsInUse=1 ansPortsFree=23 callGuid=9DB394E443A3419FA0020BC9D1A92806
00:34:50.403 |9832,PhoneSystem-1-001,9DB394E443A3419FA0020BC9D1A92806,CDL,11,CCsCdlImsAccess::AuthenticateSubscriber: Cannot authenticate user: JOESMITH IMS Result Code: 1 on line 108 of file CdlIms/src/CsCdlImsAccess.cpp: Error: 0x80046505 Description: E_CDL_SP_EXEC_FAILURE
00:34:50.403 |9832,PhoneSystem-1-001,9DB394E443A3419FA0020BC9D1A92806,CDE,3,Authentication Failed for Subscriber 555123 (Src/CsCallSubscriber.cpp 2969)
00:34:50.404 |9832,PhoneSystem-1-001,9DB394E443A3419FA0020BC9D1A92806,-1,-1,An invalid password entered when trying to log into a user mailbox. Details - [].
00:36:29.331 |9832,PhoneSystem-1-001,9DB394E443A3419FA0020BC9D1A92806,MiuGeneral,25,Enter CAvMiuCall::TransferEx destAddr='715551231234' type=2=Release maxRings=4 mediaSwitch='00a499fa-a193-45b0-a153-564a64019eb8'
00:36:33.484 |9832,PhoneSystem-1-001,9DB394E443A3419FA0020BC9D1A92806,MiuGeneral,25,Exit CAvMiuCall::TransferEx=0x00000000=S_OK
00:44:53.444 |9743,PhoneSystem-1-001,FEB6975B82284F37A161CD66ECBA61C6,Arbiter,-1,Incoming Call [callerID='' callerName='' calledID='555123' redirectingID='555123' lastRedirectingID='555123' reason=4=FwdNoAnswer lastReason=8=FwdUncond] port=PhoneSystem-1-001 portsInUse=1 ansPortsFree=23 callGuid=FEB6975B82284F37A161CD66ECBA61C6
00:45:20.019 |9743,PhoneSystem-1-001,FEB6975B82284F37A161CD66ECBA61C6,MiuGeneral,25,Enter CAvMiuCall::TransferEx destAddr='715551231234' type=2=Release maxRings=4 mediaSwitch='00a499fa-a193-45b0-a153-564a64019eb8'
00:45:24.121 |9743,PhoneSystem-1-001,FEB6975B82284F37A161CD66ECBA61C6,MiuGeneral,25,Exit CAvMiuCall::TransferEx=0x00000000=S_OK
Thanks

Hello ebergquist,
As advised we could try to run a report before an upgrade was performed to verify if it will pull the information, which in the event it does we would be matching the bug, therefore access the CUC CLI and type the following command: file get install *
You will be required to have an SFTP available for the file transfer and port 22 open on the sftp client.
Once you receive the files you would need to check system-history.log, below is an example.
=======================================
Product Name -    Cisco Unity Connection
Product Version - 8.5.1.12900-7
Kernel Image -    2.6.9-89.0.20.EL
=======================================
02/24/2013 13:35:02 | root: Boot 8.5.1.12900-7 Start
02/24/2013 16:03:45 | root: Install 8.5.1.12900-7 Success
Once you check the time stamp and date of the upgrade try to gather a report for a time range before the upgrade was performed, even though they might be overwritten, there still could be a possibility that it succeeds.
If this bug is not the issue then you might want to take into consideration:
1. Make sure that the service ReportDB is [STARTED] in the output of the command: utils service list.
2. If you have Digital Networking on your server make sure there is no stalled replication. Go to RTMT (Real Time Monitoring Tool)> Syslogs> Select on the dropdown your server> Doble click on Application logs> CiscoSyslog. You can then do a manual search or sort with the filter option:
Severity: Error
App ID: CuReplicator
Hit apply. Below is an example:
Date: Feb 19 08:01:15
Machine Name: LAB1111
Severity: Error
App ID: CuReplicator
Message: : 1151681: LAB1111.corpnet2.com: Feb 19 2013 08:01:11.662 UTC : UC_UCEVNT-3-EvtReplicatorStalledReceiveReplication %[ClusterID=][NodeID=LAB1111]: Detected stalled replication receiving from location LAB1111. Waiting for missing USN 2222. This situation may indicate network connectivity problems.
3.Make sure that replication is working properly in the cluster. You can check them via the following commands: showcuc cluster status    and   utils dbreplcation runtimestate
For the TransferEx that you state changed to ceros -> TransferEx=0x00000000=S_OK , this is just a hexadecimal value that is returned stating that the transfer that took place during the call was successful, in this case the actual transfer was to the following destination -> TransferEx destAddr='715551231234', and was during a call to ->calledID='555123' , this does not have to do with the actual change of a transfer number performed by a user.
Those traces won't be enough you will have to additionally set: ConvSub, level 3   and CDE, level 16 so that you may see output in the traces as the example posted in the previous thread.
Traces would be the path to follow in order to verify the user that changed the transfer rule, as this is as i understand the goal your pursuing.
However if it is of any help, another way to get on hold of the numbers that were updated on the Transfer Rule is to use the User Data Dump tool, this information reflects changes regardless of whether it was done via TUI (Telephone User Interface) or GUI (Graphic User Interface). For more information on the tool go to:
http://ciscounitytools.com/Applications/CxN/UserDataDump/Help/UserDataDump.htm
Traces are extensive to be reviewed if done manually, however you can do a text search with a tool as Notepad ++ to look for keywords as "NewTransferNumber =" or "CDE,16,Transfer allowed", once you find this you check the call GUIDwhich is the reference number of the call and that exists during the entire length of the call, whether it is while a person is leaving a voicemail or the user is accessing his/her's inbox. This would speed up your search.
So as explained in the first thread you would then do another text search returning all possible matches with that callGUID.
Now if you get to the very beginning of the call you would see something like:
Line 13712: 18:58:05.156 |24720,CCIE-1-001,0C9C97BDF5F444F0B535D231C32DDCB4,Arbiter,-1,Incoming Call [callerID='2199' callerName='' calledID='6789' redirectingID='' lastRedirectingID='' reason=1=DirectlastReason=1024=Unknown] port=CCIE-1-001 portsInUse=1 ansPortsFree=1callGuid=0C9C97BDF5F444F0B535D231C32DDCB4
In this example you see my test user callerID='2199' calling the Pilot number 6789 which is the voicemail button
calledID='6789, and the what type of call is it whether Forward or Direct, when logging to voicemail you are going to see Direct which is going to match the Direct Routing Rules and send the call to the attempt sign in conversation.
The other approach is a rule out method between the Audit traces and the User Data Dump tool.
So let's say you have a baseline document that states all of the Transfer numbers for all users.
If the User Data Dump reflects a different number and the Audit logs do not show any change, starting from the time the baseline was created and the point of time where the number was changed, then you could deduce the change was done via TUI (Telephone User Interface). Unfortunately you wouldn't be able to tell who did the change in this case.
Nevertheless, remember that a user may have for example an Alternate Extension so the change might not necessarily be done from the office phone: "Alternate extensions can make calling Cisco Unity Connection from an alternate device—such as a mobile phone, a home phone, or a phone at another work site—more convenient. When you specify the phone number for an alternative extension, Connection handles all calls from that number in the same way that it handles calls from a primary extension (assuming that ANI or caller ID is passed along to Connection from the phone system). This means that Connection associates the alternate phone number with the user account, and when a call comes from that number, Connection prompts the user to enter a PIN and sign in."
Best regards,
David Rojas
Cisco TAC Support Engineer, Unity
Email: [email protected]
Phone: 1-407- 241-2965 ext 6406
Mon, Wed, and Fri 12:00 pm to 9:00 pm ET, Tue and Thu 8:00 am to 5:00pm ET
Cisco Worldwide Contact link is below for further reference.
http://www.cisco.com/en/US/support/tsd_cisco_worldwide_contacts.html

ERROR WHILE FORWARDING VOICE MESSAGE FROM NOTES VIEWMAIL TO ANOTHER VOICEMAIL USER IN UNITY CONNECTION

Hello All,
I am facing problem while replying/forwarding or sending a NEW Voice Message from ViewMail integrated with IBM LOTUS Notes 8.5 to the other Voice Mail User Configured in Cisco Unity Connection.The ViewMail Version is 8.0.2 for IBM LOTUS Notes.UC version is 8.x
I have attached the file that displays the error.
From the view mail inbox if i "Right Click" any email and the "Click ON Forward" I am able to forward the Voice Message from the ViewMail to the IBM LOTUS Domino user [ that is forwarding it to EMAIL Account ], but if I try to forward it to unity user is gives "Failure Delivery".
Now when I double click the individual voice mail message in ViewMail account and then click on "Forward/reply/NewMemo" icon available on the individual voice message window that I have opened ,I get an error as stated below
"The remote name could not be resolved error in Notes ViewMail 10.0.0.152e_vmws_gen_property_not_found "
where 10.0.0.152 is the IP-Address of my Unity Connection Server.
Also just for the information I am able to Login into Cisco PCA for alll the users and able to view the Inbox.
I am able to forward the VoiceMessages between Unity Connection users via CISCO PCA without facing any issue.
A Quick Help will be much appreciated .......... :-)
Hasan Jafri

Hello Craig,
After spending sometime on troubleshooting , just for testing purpose I created two new Unity Connection Voice Mail User and configured VMN [VoiceMail for Notes] account on the same lotus Notes.
Interestingly this time I was able to use Reply & Reply to All option to send the Voice Message via VMN. {WORKING JUST FINE,NO PROBLEM WHAT SO EVER ]
But still I am NOT able to use Forward option to send the Voice Messages via VMN.
REPLY WITH HISTORY & REPLY TO ALL WITH HISTORY options are also not working.
This is error that I am getting
"Error in QueryServe in CoreUCClasses 213 at line 336:Vmws:The remote server returned an error:(403) Forbidden
I HAVE CREATED VIDEO RECORDING FOR THIS ERROR & WORKING PART OF THE CONFIG TO GIVE YOU A BETTER IDEA OF THE PROBLEM.
Its 7 MB Recording. I hope you can easily Download.
Also important point is that i don't see any previous error that was accuring during my earlier testing.
Thanks & Regards,
Hasan Jafri

Unity Connection 8.5 - No Diversion Header information in transfered call

Similar Messages

Maybe you are looking for