Using Cisco Connect with 2 different Routers

I have the linkys n300 E1200 at my office and the Linksys E1000 at my home.  How do i configure Cisco Connect to work with both of these routers so i don't have any connectivity issues?

You can only have one Cisco Connect software installed on your computer. What are your challenges with the Linksys routers? Are you experiencing slow connection? Or intermittent connection? Does it occur on both routers? Since the two routers are on two different locations, we need to properly isolate this matter to know what is really causing it. 
Updating the router's firmware will help in resolving connectivity difficulties. If the wireless connection drops, you can also try adjusting the wireless channels of the router. I am using channel 9 for my EA4500 router. Make sure as well that the router is being placed on a higher location or less interference area. 
Share more details about this matter. Community users are here to help.
Help, learn and share

Similar Messages

  • Using Cisco Connect with several E1000 routeres

    I have two E1000 routeres, one at home and one at the office, and I have installed the Cisco Connect (CC) software on my laptop, and used it to congifure both devices with.
    The first time I tried to connect CC to the router at the office, it removed the settings from my home router, and accessed the E1000 ok and I could configure it without any problems via CC.
    But when I now tries to use CC to configure my home router via CC, it keeps complaining about me not beeing connected to the right router, and CC won't allow me to connect to my home router eventhough I type in the correct password etc.
    Does anybody know of a trick to use the same CC for configuring multiple E1000's ? Or how to get CC to "forget" its settings and connect to a new E1000 router?
    Thanks.

    So the concern that you said is the configuration of the Router ( E1000 ) at home.. So could please inform us the name of the ISP( Internet Service Provider )... So it all depends upon the ISP( Internet Service Provider ) setup...
    If you want to configure the router with the help of the CD so for that you need to uninstall the existing Cisco Connect Software from the computer...
    Reset the Router and power cycle the network...
    Make the following connectivity Modem ----> Router -----> Computer... Then install the Cisco Connect Software... It will help you in configuring the Router...

  • Can I use Cisco Connect if I change the default router IP address?

    I am adding my E3000 into an existing network behind a SonicWall firewall.  I am using an address scheme of 192.168.168.xxx  When I change the router address to 192.168.168.10 and disable DHCP in Cisco Connect, I am left with only being able to access the router through the web interface.  This seems pretty lame; I've read other threads on Web vs. Cisco Connect.  Is there a quick fix that will allow Cisco Connect to still find the router after I've made (just) these two changes?
    --David C

    Yes you still will be able to use the Cisco Connect software if you have changed the Routers IP address, But if you change the Router password of Wireless Security then you wont be able to use Cisco Connect software.

  • Can I use 1 computer with 2 different iTunes accounts and devices? We're afraid we're going to wipeout one library or the other if we do??

    My son got an iPhone and wanted his own iTunes account. Now his computer died, and he wants to connect to his iTunes account on my computer. When it asks to sync the computer, a message comes up and we're afraid either his or my library are going to be wiped out by trying to do this. Is it possible to use 1 computer with 2 different iTunes accounts and devices without wiping out one of the libraries? Thanks for any info.

    If the content was not originally purchased/synced to the device from your computer it will erase and replace the content from the device with that of the computer. If you have content that you want to backup you can transfer purchases http://support.apple.com/kb/ht1848 check this link out

  • Using Cisco WCS with Microsoft IAS

    Hi.
    I have two 5508 and WCS 7.0.172. I want to user Active Directory users credintals to login on ther WCS. Have a configurated NPS role on server with windows 2008 r2.
    I have read this http://zmq503o1.wordpress.com/2008/01/06/using-cisco-wcs-with-microsoft-ias/ and done the same.
    I dont't agree with "on the "Encryption" tab and clear all the checkboxes except "No encryption" - wants an encryption connection but this didn't work till in user's properites in AD permit "Reversible encryption". This is not what that I want.  Would I need to generate ssl-cert for the wcs as wroted this?http://www.cisco.com/en/US/docs/wireless/wcs/7.0MR1/configuration/guide/hard.html#wp1042471
    or doing smth else? thx

    Camera is only supported for use with CUVA. Any other application attempting to utilize the camera is not tested and is not supported.

  • Not allowed to use Cisco Connect anymore. Help?

    I recently changed my wireless password, in the advanced settings, to not match my router password. Now that I try to use Cisco Connect, it says that I can not because I changed the a password in the advanced settings. Is there anything i can do to undo this change?

    If you change the password of the router or wireless network using the setup page of the router then Cisco connect software will stop working. You can change the router password to match with Wireless network password.
    Open the setup page of the router. Go to Administration tab and change the router password.
    See if that makes Cisco connect to work. If not then I think you will need to reset the router and reconfigure it.

  • Remove guest access without using 'cisco connect'

    Hi all,
    I just installed a new Linksys E3000 and was able to use "Cisco Connect" up until I decided to forgo the "Wi-Fi Protected Setup" and use manual settings.
    Well, after having done this, I can no longer use Cisco connect, and I really want to get rid of the additional "-guest" network which seems to be tagged onto my main network.  Is there anywhere via the browser-based admin that I can get rid of the guest access feature?  If there is, I can't seem to find it.
    I tried switching back to the  "Wi-Fi Protected Setup"  feature so I could go back to using connect, however it no longer seems to see my router when I try to connect to it, so this is no longer an option for me.  I'd really like to avoid reinstalling the router all over again.
    thanks for any info.

    If you have configured your Router using the Cisco Connect software, then you it secure your wireless network with an password. If you have any firewall and antivurs software on your router then it will protect your computers against worms.
    To use the FTP feature of your router you need to enable ftp login on your router, which you will find under the storage tab of your router.

  • Another "This itunes account is set up to use family sharing with a different icloud account than Apple ID "

    I saw another thread on the matter but thought I would post because the circumstances are different. Here is how it happened.
    I have had an Apple Store account for years and until recently our family has only had our one Mac and my iPhone 4. Thus any purchases we have made on the Apple App Store were made only with this account.
    We recently purchased two iPhone 5S's--one for my wife and one for my daughter. Neither had Apple IDs so first we set up my wife's iPhone and created an Apple ID for her. Next we used the Family Sharing feature to set up an account for our "under age 13" daughter.
    Because I am still waiting for my iPhone 6 Plus to arrive, and because the iPhone 4 cannot upgrade to iOS 8, and because my Apple ID is the only account with any apps that have been purchased in prior years, I set up my wife as the Family Organizer but when I set up her account, I chose the option to "share purchases from a different account" and entered the information for my Apple ID.
    My daughter is able to view my prior purchases on her iPhone, but when my wife tries to view my prior purchases, she receives the message "This iTunes account is set up to use Family Sharing with a different iCloud account than <her Apple ID>."
    I hope Apple is reading this. I would be more than willing to help them on this one as this feature is one of the main reasons I put our family on iPhones.

    I had this problem. I finally figured it out yesterday. Try this:
    On the device that is having trouble seeing purchases, go to Settings>iCloud>Family Sharing> Then tap on the user of the device you are on. Under "Family Purchases" make sure it has the AppleID of the person for that device. Mine originally had my husbands AppleID in there (he is the Organizer), but I changed it to mine. That doesn't make it so that the purchases are under me. The purchases remained under my husband, but my ID had to be in this spot for it to work.
    After that, I closed settings, then I went to Settings>iTunes and App Store> click on the AppleID and Sign Out, even if it has the right AppleID in there. Then Sign In again using the AppleID of the person on that device. Again-- even if it has the right ID in there to start, still sign out and back in.
    See if they show up. If they don't show up still, try doing a restart (hold down power button and home button until it restarts).
    They should show up by then, but if they don't, at that point, try to go into iCloud and Sign Out and back in.
    I think the key is having the right ID in "Family Purchases". I hope this works for you.

  • How do I use Home Sharing with two different apple accounts?

    How do I use Home Sharing with two different apple accounts?

    Morning Saintine,
    Thanks for using Apple Support Communities.
    Home Sharing enables you to stream or transfer music, movies, TV shows, apps, and more among up to five authorized computers in your household. To do so, you will need to Turn on Home Sharing on each computer using the same Apple ID.
    Understanding Home Sharing
    http://support.apple.com/kb/HT3819
    Hope this helps,
    Mario

  • HT4623 My iPod Touch is te 4th generation with iOS 4 only... The desktop that it used to connect with was broken and I couldn't update my iPod touch as all content is linked to the iTunes on that broken PC. What should I do?I won't erase all my music reco

    My iPod Touch is te 4th generation with iOS 4 only... The desktop that it used to connect with was broken and I couldn't update my iPod touch as all content is linked to the iTunes on that broken PC. What should I do?I don't want to erase all my music recording. (couldn't back up easily...) my dairy, my financial record made on apps...
    If I got a new Mac book pro soon, would it helps backuping everything?

    awesome121, he does not an an iCloud account. You need iOS 5 or later for iCloud and the poster said he has iOS 4.
    awesome121 wrote:
    DO you have a icloud account?

  • Using a ipod with two different computers...

    I just bought a new laptop and had to download itunes again but when i hook up my ipod it tells me that that ipod is already synced with another computer (my main desktop comp.). Is there a way to use my ipod with two different computers, or can you just use one computer at a time?
    thanks!
    Dell Inspiron 1505   Windows XP  

    You can use more than one computer, but you'll have to load your iPod MANUALLY if you do, otherwise it will keep erasing things to match the library it's hooked up to.
    http://docs.info.apple.com/article.html?artnum=304711

  • Using Cisco Connect

    I am trying to change the password on my Guest Account but am having no luck.  I do not have a key and when I click on the Cisco Connect icon it tells me ....
    "The router password or wireless settings have been changed using advanced settings.  This applies the changes directly to the router and you can no longer use Cisco Connect."
    Inserting the set up CD get me nowhere as it thinks the router was set up on another PC.  Not the case.  So, what do I need to do to move forward?  Is there a logical reason as to why this activity is not part of the router interface?  Is there a plan to change this debacle?

    Found out that I must reset the router and start from scratch to get into guest account settings.  I just can't believe Cisco would set up a product this way.  Oh well.  You pays your money and takes your chance......

  • "this itunes account is set up to use family sharing with a different iCloud account"

    I set up an iCloud family. Until now, everyone had their own iCloud account, and we had a separate iTunes ID (not an iCloud e-mail address) that all of our purchases were made under.
    So, I set up that Apple ID as the master account and added everyone's personal iCloud accounts as members.
    Then, I went into iTunes prefs and logged in as my iCloud account.
    When I go to the App store and go to Purchased, it says:
    "this itunes account is set up to use family sharing with a different iCloud account than <my iTunes Apple ID>." Then there is a Learn More link that takes me to my iCloud and shows my family group with the same Apple ID as the organizer.
    Does anyone have any idea what happened to cause it to think that I am not in the same family group?
    Thanks.

    Update...I now notice:
    Going to: App Store>Updates>Purchases:
    1)  The message “This iTunes account is set up to use family sharing with a different iCloud account other than <her iCloud ID>...”  Is now showing up on my iPhone and can no longer see any of my purchases or hers. 
    2) The same message above is now showing on my iPad mini (it didn’t before).  But, I can still see both hers and my purchases on my iPad mini. 
    3) The message "This iTunes account is set up to use family sharing with a different iCloud account other than <my iCloud ID>…” still showing on her iPhone and she still can’t see her or my purchases.
    iTunes Family Sharing still works fine.
    Note: If I Go to Settings>iTunes & App Store then log out of my Apple ID, then go to App Store>Updates>Purchases and log into my Apple ID from there, My purchases show up (not hers). I then toggle between Updates and Purchases and the message pops up and unable to see any purchases, again.  Same thing happens when I do it to her phone except her purchases show up (not mine).
    I emailed this update to Apple...waiting for a reply.

  • Receiving emails about a newly set up itunes account that does not belong to me (although has my name). The address used in connection with it seems to be in California and the person likes Justin Bieber - what's going on here?

    Hi. I am receiving emails about a newly set up itunes account that does not belong to me (although has my name). The address used in connection with it seems to be in California and the person likes Justin Bieber (as I now have a receipt for that purchase). It states that it is billed to store credit. (a) I don't want to receive this person's information and (b) I certainly don't want to somehow be charged for it (although it appears, thus far, that I have not been). What's going on?

    i didn't read a lot of your 2nd paragraph, but it seems like the password is the issue, right?
    do a true clean install
    reboot your machine and hold down command+option+r, you should see a spinning globe - if you don't see the globe or anything that reads internet recovery, shut down and try again
    at menu, chose disk utility and once there, find your HD on the left side, select the physical name and erase it as mac journaled
    exit disk utlity
    at menu, choose install OSX
    this time, when it asks for a password just hit continue, it will let you complete without a password
    you should be able to get into your laptop, now figure out what password you'll be able to use with your kb issue

  • Manually managing E3000 / not using cisco connect software

    ok  now i have totally by pass the cisco connect  software, and manually managing my e3000 / updating the firmware manually  and i have the ssid disabled due to people trying to connect to our router all the time and our router is password protected (wpa/aes) i need to know if manually managing the network is a good idea or not i've manage other linksys routers in the network page, i am finally able to connect and i get my full download speed 10MB/Second  now  before i was getting 5MB/second and upload speed is at a good 1MB/second before i was getting 0.3MB/second are these good speeds or what i dont know i've also ran a few test - both the hdtv & xbox on at the same time running the same item (netflix's ) both at the same speed 

    For better wireless connection, use WPA2 with AES security.
    I think disabling the SSID broadcast will make any difference.
    You can also try changing the advanced wireless settings on the router.
    Connect the computer to the router with the Ethernet cable. Open the setup page of the router and go to Wireless tab. Click on Advanced wireless settings sub tab. Change the Beacon interval to 75, RTS and Fragmentation threshold to 2304. Save the settings.
    Click on Setup tab and change the MTU size to 1365.Save the settings and power cycle the router.
    Now observer the wireless connection and see if that makes any difference.
    Also make sure that your router is running on latest firmware.

Maybe you are looking for