Which type of PCMCIA slots has Portege 7220?

I've just got a Belkin USB 2.0 pcmcia card to fit in one of my pcmcia slots. This should give me 2 USB 2.0 sockets. I've put it in and my laptop is not seeing it at all. Thought it was a driver issue (I'm using XP) but now suspect that I don't have a Type II slot, It is an old laptop.
Can any one here tell me?

For USB 2.0 you for sure need CardBus slot. Portege 7220 is not old at all, it has CardBus (you would not be able to insert the card otherwise, BTW). However, if PC card slot is set to PCIC compatible (not CardBus/16 bit) the laptop would behave the way you say. Check you BIOS settings.
Hope this helps.
Regards,
Vitaly

Similar Messages

Which type of PCI slots do I have?

I want to upgrade my graphics card for gaming. I want to install a NVIDIA GeForce 8800 GT which is a PCI Express 2.0 interface. Can I put this in my MacPro? What are my options for better cards? From what I understand, which may be wrong, is I have 4 PCIe ports and 1 PCIe2 port? I can't seem to find anything in the System Profiler that says definitively.
The card I have says this under the Graphics/Displays section:
Chipset Model: NVIDIA GeForce 7300 GT
Type: Display
*Bus: PCIe*
Slot: Slot-1
PCIe Lane Width: x16
VRAM (Total): 256 MB
Vendor: NVIDIA (0x10de)
But then under PCI Cards it says:
NVIDIA GeForce 7300 GT:
Name: NVDA,Display-B
Type: display
*Bus: PCI*
Slot: Slot-1
Vendor ID: 0x10de
So I am confused because I cannot tell if the NVIDIA card is PCI or PCIe. Do I have four regular PCI slots and one PCIe slot or four PCIe slots and one PCIe2 slot? What options do I have for video cards that are 512MB or larger? I have some games that I would love to turn on all of the effects to the highest quality, Quake 4 being one of them. Thanks in advance!!

Ooops, my bad, so there are only two different options? And they are both 512MB? I don't really see anything that says 512MB of VRAM or anything for the Radeon. ATI is now owned by AMD. It seems they may just discontinue Mac support. I don't want be stuck with another unsupported card. Last time was with the VooDoo 64MB card that came out for Mac when I had a G3. 3DFX went out of business shortly after.
Quadro 4500 FX and the ATI Radeon X1900 XT? Both are 512MB, is one brand better than the other? Is there anything bigger? I have recently read a lot of reviews of the Radeon cards over heating. I would like to get something better if possible and prepare to not have to upgrade again so soon. Also nVidia has these other Quadros on this page:
http://www.nvidia.com/page/qfx_uhe.html
Are none of the others in this list compatible? They are all PCIe. Is it just because there are no drivers?

PCMCIA Slots

Please help! - I've got a ze4096ea laptop, and I need more usb ports. Answer: get a multi-port PCMCIA card.
Problem: - Just WHAT PCMCIA slots have I got in the machine? - I can't make head or tail of the specs. manual.
Have I got PCMCIA Class I, Class II, Cardbus or what?

They are Cardbus slots which just means they are capable of 32 bit data transfer. The form factor is Type II which means they are ordinary credit card thickness. Get a pcmcia/cardbus usb 2.0 card that has a power jack on it. You use one of the onboard usb ports for extra power with a usb to power jack cable. I am not even sure that your ze4000 has usb 2.0; in fact I am pretty sure it does not. I have had the best luck with the Belkin usb 2.0 card:
Belkin
This is only a 2 port card but you gain 2 high speed ports by giving up one low speed port, which is fairly useless anyway.

What wifi cards fit fully inside a (dual) PCMCIA slot?

Teh background and information (bonus funny story)
So I was poking my 9 year old laptop recently and amazingly found that via a USB wifi dongle I'd completely forgotten about for a few months, I could get wifi on said laptop, even over USB 1.1.
Then I tried to figure out how to shove the dongle inside my laptop and things kinda went south from there at about 2.7 billion miles a second.
Everything just went *flooooop* when I accidentally put the little PCB back inside the dongle the wrong way after taking it out to try and fit it inside a space inside the laptop; this wasn't problem, except I couldn't see the little blue LED. So I hastily took the board out to flip it over and I think I touched the it while doing so for the first and only fatal time...
I also tried to craft a cardboard plug to fit in the USB port on the laptop, and may have pushed the little contacts into the plastic recesses in the port a bit too much; this is unlikely to be the problem because I very carefully re-bent the contacts out again, and my flash disk works every time I plug it in, sooo... probably not that.
Anyway, now I know how to put my laptop back together again *doesn't say anything about the small collection of screws he has no idea what to do with*
Right now, my USB dongle kinda works but really sporadically; it mostly doesn't work at all. It fails anywhere between the kernel thinking the "USB cable is bad" (</quote>) to fully detecting and configuring the dongle (under either an rtl8187 or ndiswrapper-powered driver), but not letting me connect to any SSIDs. I typically have to unplug the thing and shove it back in in the previous case, or give up in the latter, which I've no idea how to get around, until it feels like connecting again (perhaps after cooling down?).
So I want to try a PCMCIA type card because...
- I can't use my flash disk without a hub right now, since the dongle would occupy the only port available (although linux does say there's a 2 port hub inside >.>).
- The port has a cute little flap over it that I don't want to remove, and it causes my USB dongle to not be able to go in properly unless I use a cable
- I'm all like jittery about the USB port possibly not working =P
I've found it impossible to find any sort of specification sheet for this box so I have no idea what kind of PCMCIA port it has, but I'd imagine type #1 if that's of any help. The laptop itself is a Toshiba Satellite 2540CDS also.
Teh point
I want to get away from the whole "vulnerable peripheral sticking out of side of laptop" thing and get a PCMCIA card that fits fully inside a laptop's PCMCIA slot, preferably without needing to use an external antenna.
I don't mind if the card takes up the space of the upper slot as well; I'm not using that one (and doubt I will soon).
I've been told that cards like this exist, but (of course) I only want one that is known to work with Linux, or at least one that should theoretically work (ie because it uses a supported chipset), and one that includes an internal antenna.
Although an antenna sticking out the side sounds like it'd look cool, so I might be okay with that once I see what it'd look like
So what do you recommend?
-dav7
Last edited by dav7 (2008-11-03 05:28:43)

Hi Steve
Well, I cant give you proper answer how you can exactly remove the PCMCIA slot.
There are many screws and in my knowledge you have to remove all covers and screw which are placed at the bottom of the unit and inside under the keyboard.
Please check this unit precise. Maybe you have overlooked some screws.
But if it impossible to remove this PCMCIA slot from the unit I recommend to ask the service partner for a detailed instruction.
Good luck
Bye

What is open firmware command to boot a Powerbook G4 from a CF card in the PCMCIA slot?

I have a Powerbook G4 Titanium with a bad motherboard that will no longer power the internal hard drive. I want to to install an OS and boot from a CF card in the PCMCIA slot. I understand this has to be done from Openfirmware, but I cannot figure out the command to do it.Does anyone know?

Charles,
Welcome to Apple Discussions.
What I've found so far is a non-Apple solution drivers.
I assume you've found the IO Xperts driver. (http://www.ioxperts.com/products/80211b_X.html)
Is there an Apple developed solution out
there for third party cards?
Not exactly. Apple uses the Broadcom chipset. Some third-party manufacturers also use the Broadcom chipset and those cards would then work with the AirPort drivers. Here is a link to a list of wireless cards that note the chipset, OS and driver.
http://home.earthlink.net/~metaphyzx/Wireless.htm
(Note: the list is dated August 2005.)
Manufacturers change their chipset so the version number of the card will make a difference. For example, the list shows that the Linksys WPC54G uses the Broadcom chipset. Well, that is true with version 1. Version 2 uses a Texas Instrument chipset and version 4 uses the Inprocomm chipset, which means these two do not work with the AirPort Driver.
I use the Linksys WPC54GS v1.0 (SpeedBooster) that uses Broadcom. It was plug 'n play.
It is hard to get an original Airport card today.
A quick search found a number of sellers, but they cost 2-to-3 times more than a third party card. (I didn't check eBay.) A third-party card also avails you to the faster option of 802.11g.
Hope this helps.

Satego X200-21D - Specifications of PCMCIA slot

Hi all,
can someone told me the specific for the PCMCIA Slot? In special I wanna know how much Volt the slot has.
3.3 V or 5 V or can the slot both of them?
Kind regards,,
Adrian

Hi twister666,
The Satego X200-21D doesnt have PCMICA slot, it has Express Card slot. This slot allows you to insert an Express Card. An Express Card module is a small, modular add-in card technology based on PCI Express and USB. The max. transmission rate at 2.5 Gbps. Both 34mm type and 54 type are supported.
But about voltage I can find no information but I think thats not important because there is a standard voltage for this specification that every card will work.

Scrap Sales GL , which type of cost centers need to assign in OKB9

Dear Seniors,
G L account : Scrap Sales:
For this GL a/c , cost element created with Cost element category u201C11u201D (Revenues).
Now in OKB9   i want to make assignments:
With each b.area and cost centers.
Now my doubt is :
In OKB9 which type of cost center I need to assign from the below.
1.Cost center should be with
Cost cntr category u201CFu201D (Production)
Or
2.Cost center category u201DVu201D (Sales)
and another doubts is , in Cost center -control tab: Actual revenues check box, should i select or not in any case.
Please clarify my doubt.
Thanks in Adv

Hi,
As scrap sales are revenue to the company, undernoted things to be noted here :
1. The cost element category is V - Sales and the control indicator actual revenues box to be unticked.
     The posting will be statistical for revenue elements.
2. The revenue recognition has to be equally done in VKOA for the account assignment of this account.
3. You can create a seperate order type for scrap sales and a sales pricing procedure in SD.
4. Check whether the scraps are defined to capture Tax Collected at Source, if so, you have to define
     condition types for them too.
5. If the material itself is defined as scrap material then in Material master the Profit Center would have
     been assigned and to capture the revenue assign the scrap sales revenue in VKOA.
Best Regards,
Sadashivan

PowerBook G3 (PDQ) - Startup disk and PCMCIA slot problem

Hello
I have encountered a problem with my powerbook G3 (PDQ model)
Once when I had to configure my microphone, I saw that there was "Zoomed video" present in the list of audio inputs.
I thought this was a glitch, and inserted my SD card reader into the lower PCMCIA slot. Then my display got messed up.
The slot insertion doesn't seem to work right too, it resists much more than the top slot does.
It didn't react to anything except Fn-Shift-Ctrl-Power, which is Reset.
It happens in both OS9 and 10.2.
Photo: http://instagr.am/p/NtWNH/
Once I was able to insert it right so it wouldn't mess up, and i used the reader in the lower slot as usual.
When I ejected it, the card didn't pop out as usual and it was hard to pull out, and the screen was messed up as well.
The second problem is that when I start the "Startup Disk" control panel in OS9, the PowerBook hangs for no particular reason, also reacting to Reset only.
Maybe there is a bootloader I can install so I'd choose the OS I want before actually booting anything?
Could these problems be related to each other, or a dead battery? Maybe to the incorrectly set clock (however doesn't seem so)? Or related to using an Apple DVD drive?
Thanks,
~ Vladislav Korotnev

No it hasn't. What kind of battery does it use?
The power battery is dead as well (not charging nor powering the pb)

Which type of HDMI cable?

i have Hp pavillion dv6-6121tx laptop and i want it to connect with my TV through HDMI cable.Which type of cable should i buy 1.3B or 1.4B or they just don't matter?please tell me

Please see this Wikipedia article entitled "HDMI" for a comparision of the different revision numbers. For most applications, it doesn't matter if you use v1.3b or 1.4b.... But getting the newest revision gives you the flexibility to use the latest and greatest if you choose to.
Please send KUDOs
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Which types of external hard drives works with T400?

Hi Thank you for reading my post.
Can someone please let me know which types of external hard drives works with a T400?
eSata, USB or firewire?
Which model and brand you suggest for a 1TB drive?
Thanks

USB 2.0 is the connection that is natively supported on the T400, no eSATA or Firewire port i think, you can get these ports by buying an expansion card for the card slot (i think it is the expresscard one) on the T400.
Regarding a 1TB drive, most of the large drive manufacturers have one out, but i suggest you unless you need the large capacity, i would stick with a smaller drives like 750 gig or 500 gig since the cost gigabyte is lower. Also i would stay away for storing all your important files solely in these drive, because if these things start to fail it would be on a moment's notice, you probably won't even have time to backup the files, before the harddrive gives up on you.

Please help me my phone which is nokia c6 01 has p...

please help me my phone which is nokia c6 01 has problems of USB.when it is on i see a message on screen which is : connect USB cable to device and when i press ok the moved away and the message also back to the sreen please help me

Hi bigbow,
Welcome to Nokia discussions board!
In order to fix this issue, I advise you to perform a soft reset: type *#7780# on your phone's keypad. The default lock code is 12345. If the issue persists, perform a hard reset. First of all, back up your data using Nokia Suite. Once your data is fully backed up, type *#7370# on the keypad.
Let us know how you get on and feel free to post any other questions you may have.
Regards,
astra2025
Press the 'Accept Solution' icon if I have solved your problem, Kudos my post if my advice has helped you!

Pismo PCMCIA Slot

I am trying to figure out if the problem I am having with my Pismo's PCMCIA slot is a slot failure or an incompatible PC Card. I am using a compact flash adapter that works in my powerbook g4 but in the pismo it just causes the finder in os9 to crash. in osx nothing happens at all and in both cases the apple system profiler shows nothing in the slot. also, when i boot from the os9 install cd it asks if i want to initialize it and then it fails. I have tried another pc card that reads memory sticks and it also doesn't work. Is the pismo finnky with pc cards? the airport card works, is that on the same bus? none of the pins are bent in the slot, it just seems like nothing is wrong.
thanks for your help guys.
Jeff

Jeff,
Before replacing any parts, I would try a little more troubleshooting.
Try a FireWire or USB PC card in the Pismo.
In 9.x and FireWire PC card, you already have the FireWire Enabler and FireWire Support extensions, but you will need to add the FireWire CardBus Enabler in the Extensions folder. You can get one here:
http://www.versiontracker.com/dyn/moreinfo/macos/10842
In 9.x and USB PC card, you already have two necessary extensions, USB Device Extension and USB Software Locator, but you need three additional USB extensions for the USB PC card:
USB Mass Storage Extension
USB Mass Storage Support
USB Support
You can easily get these three extensions here:
http://eshop.macsales.com/tech/ftp/usb/usbextensions.sit
Expand the .sit file and just drag the three extensions to the System Folder icon or drop them in the Extensions folder. These are the five extensions:
USB Support v1.4.1
USB Software Locator v1.5.6
USB Device Extension v1.5.6
USB Mass Storage Support v2.0.4
USB Mass Storage Extension v2.0.4
In 10.x and FireWire PC card, all necessary software is present.
In 10.x and USB PC card, all necessary software is present. BUT, if you do not have a USB PC card with the correct USB chipset/controller, it will not work properly.
There is another limitation with PC cards...they do not supply sufficient bus power to run anything but the lowest powered devices, e.g. mouse on USB PC card. I have read that a USB PC card will mount a USB flash memory card.
My suggestion is this for the least amount of work: Beg/borrow a USB card and use in 9.x only after adding the necessary extension. See if the card shows up in the System Profiler; test a mouse; your iPod should also work; a USB HD should also work if it has its own power supply. You can also test a FireWire PC card in 10.x without adding any software. If you have a FireWire HD with its own power supply or a FireWire CD or DVD burner, it should work.

Since downloading OS X Yosemite I have been having issues with Netflix. Video slows down which causes the audio to go out of sync. Netflix plays ok on ipad which makes me think it's the software which is the issue. Has anyone else had this issue?

Since downloading OS X Yosemite I have been having issues with Netflix. Video slows down which causes the audio to go out of sync. Netflix plays ok on ipad which makes me think it's the software which is the issue. Has anyone else had this issue?

Try this:
Go to System Preferences - Bluetooth. Delete the keyboard from the list of devices by pressing the "-" button. Take the batteries out of the keyboard and reinsert them. In Bluetooth Preferences press the '+" button to add the new device. If the keyboard begins to pair, click the word "pair" and type in the passcode. Press return. The keyboard is now paired.
If the mouse is not pairing, try this: shut down the computer completely, unplug any USB mice, then turn off the power to the bluetooth mouse. ONce the computer starts up again, wait for the pop-up looking for a mouse. Turn on the power to the bluetooth mouse. It should work normally now.

No expense type for estimated costs has been defined

Hi SAP guru,
My client wanna check budget from travel request. Check budget through Funds Management already available when post travel expense before posting to FI however they need on the travel request.
I read the documentation, it could be happen when approval the travel request. The problem is travel request used the activity, and try to enter the estimated cost as value.
When we enter the estimated cost, system refused with error message:
No expense type for estimated costs has been defined. Cannot save
Message no. PTRA_WEB_INTERFACE174
How to link the expense type to estimated cost?
or how is the scenario in order we can check budget from travel request?
any kind help will be appreciate,
dewi

Hello Dewi,
If you have the funds management active, you need to go to
maintainance view V_T706B1 and create an expense type for which
you choose out of the 'special use' drop down box the value
'estimated cost, no reimbursement'.
Background: When saving a travle request we build up a commitment
for the estimated cost. This is new functionality.
Regards,
Raynard

Portege 7220 and windows 98. Black screen during installation

Hi,
I am facing the following problem when I am trying to install win98 on the above machine Portege 7220 (/PIII650/64/12/13t/M), on its docking station ...
I boot from a diskete and I access the cd rom (e:\) in order to run windows 98SE setup. After I type e:\setup.exe I get a black screen and the computer freezes. However I can install windows NT or 2000 on the this machine, and moreover the windows 98SE cd runs ok on other computers, i.e. no black screen!!!!
Any idea what is wrong?
Thanks in advance,
Bar

Hi Bar
Please don`t be mad on me but I must ask you something. Do you use Win98SE full version or just update CD for Win98?
It can be that your CD is scratched! So please try another CD again or another OS like W2k!

Which type of PCMCIA slots has Portege 7220?

Similar Messages

Maybe you are looking for