Wireless WPA Enterprice 802.1X Not working

We have problems at work. We are unable to connect any mac to the network using Wireless WPA Enterprice 802.1X. The authentification process works and I get authenticated, but I'm unable to access anything. The wired network settings work fine though.
Could anyone help out with this and share some information?

The 169 address is self-assigned, which means that your Mac isn't getting any response from the wireless device. It isn't on any sub net and pinging isn't going to happen. Are you sure that it is even really authenticating? Type in a garbage name and password.

Similar Messages

  • My wireless keyboard and mouse do not work on my All-In-One computer?

    Q.: My wireless keyboard and mouse do not work on my All-In-One computer?
    A.: If your wireless keyboard and mouse do not work even after changing the batteries, please try re-syncing them by following these steps.
    1. Make sure the computer is on, plug in the USB receiver. Push the button on the USB receiver until it flashes blue.
    2. While the receiver is still flashing, press the red connect button on the keyboard (Make sure the batteries are installed). The USB receiver should stop flashing after pressing the button on the keyboard. It may take up to 8 seconds to sync.
    3. Repeat the same process for the mouse. Push the button on the USB receiver, then press the connect button on the mouse (Make sure the mouse is on).
    Note: This applies to all MSI All-In-One computers that include the ES500W wireless keyboard and SW130 mouse.

    "This machine has an added 4 USB ports, could this be causing a problem?
    It definitely could be the source of the problem. Perhaps the PCI card was bumped loose during shipping?
    Have you tried removing the card? That's where I would start.
    Keep us posted.

  • Windows 8.1 with Hyper-V external switch - 802.1x not working in host nor guest

    Hi,
    I have Windows 8.1 with installed Hyper-V and virtual machines connected via Hyper-V Switch - External. 802.1x wired authentication is not working in host nor in guest machine (computer is not responding to switch requests). If I will change switch mode
    to Internal/Private it will start working.
    Do you have any idea how to get it working also in external mode?

    Hi,
    What is the physical network configuration in your environment? Are you using wireless or wired connection?
    We tested this issue as you described here, and the external switch is working fine.
    Have you tried to delete the created switches and recreate one, test this issue again?
    Yolanda Zhu
    TechNet Community Support

  • Wireless card seems to be not working

    Hello everyone,
    I haven't had any problems with my wireless card for my Macbook Pro since I purchased it, but something seems to be acting up now. Here's the situation...I went away for the weekend, took my laptop with me, didn't use the internet at all. Then I came back to my wireless card not working. It has a self-assigned IP address of 169.254.183.17. I did some reading on it and what people of said is that when you have this particular address your computer can't access the internet. I have power cycled both the router and modem correctly without any success.
    I have another laptop that is windows based that can connect wirelessly so I've identified that it isn't a router problem. The thing that baffles me is that I can hard wire my Macbook into the router and achieve a connection...any suggestions on what I should try next?
    Thanks in advance.
    Message was edited by: Jaden Pretzlaw

    Thanks for replying,
    I did go into advanced settings to see what was up. And the TCP/IP tab was the area that I was focusing on. Okay...I did try renewing the DHCP lease and it keeps giving me the unusable IP address. One potential problem that may be contributing to this fiasco is that I think the modem in my household is also a router (which we're just using as a modem). The modem isn't mine so I'm not sure how it was setup. I don't believe that modem is activated to give off a wireless connection. I don't know why it would be a problem because I was connecting to the router just fine before. If the windows based laptop can connect just fine, it wouldn't be the router...(just thinking out loud here).
    I was given an option by one of our IT personal at the office that I work at...he said that I could completely remove the network from my saved list and re-enter it. He also said that I would have to delete some temporary files that are saved in a hidden folder that are "preference" files for that specific network. I wasn't able to find that folder, and I did try deleting the network but it didn't seem to fix the situation. If I could simply just go back to square one, as I did when I first connected to the network I'm sure it would fix everything.
    I hope this wasn't too long to read, hopefully it gives good insight.
    Regards
    Message was edited by: Jaden Pretzlaw

  • America's top number one wireless service...does not work in Puerto Rico

    Please come back to Puerto Rico. I have been a member for over ten years. I live in Ohio  and will have to relocate to Puerto Rico.  My daughter is enrolled in college to become a school teacher in Puerto Rico. My family plan is not working well in Puerto Rico. I am paying for a family plan, (here in Ohio) and my daughter has two phones in Puerto Rico. They are not working. I had called Verizon Support, and was told that the phones must be mailed back to (Ohio)  me here in the states to be reactivated. Verizon phones cannot be activated in Puerto Rico. I prefer only Verizon, which is why I have not switched to any other provider. But, because Verizon does not have towers or businesses in Puerto Rico, even though we have 4G phones, we now have no service in Puerto Rico.   I am stuck with the choices of AT&T, T-Mobile, or Straight Talk from Wal-Mart, or the WORSE are the wireless and Internet services of Puerto Rico, Claro.. Claro has outages for DAYS and still expect full payment, regardless of how many days lost for service. Claro does not credit your account even if you had an outage for a week; you are still billed for the full month.  It is difficult to avoid this company in Puerto Rico. This is a message to CEO of Verizon...please bring your business back to Puerto Rico. When people asked my daughter what service she uses, they were excited when she said that she uses Verizon. But were disappointed when she said that her account is back in (Ohio) the states, there are no stores here. I have to send (AGAIN) two new phones activated here in the states back to Puerto Rico, so that my daughter can still use our Verizon Family Plan. There is nothing Verizon Support can do.  Once I move to Puerto Rico, there will be no one to send our phones to in (Ohio) the states to reactivate for our Verizon Family Plan. The phone service works for about three or four months, (in Ohio) than there is no service at all. Please bring America's top number wireless service back to Puerto Rico. Or Make some kind of deal with the wireless tower owners in Puerto Rico, so people that even visit Puerto Rico can use your phone service. Thank you for reading my request

    Our home line has had no dial tone for two days now.  When a repair was requested, we received a commitment of 8/8.  That timing was not sufficient.  I updated the repair request on line indicating that we needed the repair by today.  I called this morning and a recording told me that Verizon was committed to repair the phone by 8pm tonight.  Well, 9:30pm and no Verizon.  I tried calling with my cell phone and sat on the phone for over 30 minutes.  Either no one was home or it was past business hours.  In any event, here we sit with no home phone service.  We are elderly.  My husband has a heart condition.  I am grateful for our cell phones, not Verizon.  What if we had a real emergency and didn't have cell phones?  This is not customer service.  We never even received a phone call or an email as we requested on the repair status.  So sit another day or maybe more.  Frustrated in NJ.  P.S. Our experience with My Verizon is it sends you round and round and round with no real solution to your problem.  Any suggestions? Thanks.

  • Apple Wireless Keyboard - Shift + 'r' key not working. It doesn't capitalise the letter. Can someone help please. Thank you.

    Hi all,
    I am having some problem with the Apple Wireless Keyboard. It has not problem connecting to both my iPad mini / iPhone 4S.
    The problem comes when I start to type with it. All the keys are functioning will, except when I am trying to capitalise the letter 'r'.
    I tried using Shift + r. It doesn't work, regardless whether I use the left or right Shift key.
    Any someone help please. Thank you.

    If your Macbook is less than a year old, it is under warranty. A repair of of a problem of this kind would be free. So, if you have a warranty, have the problem fixed by Apple.
    If your Macbook is more than one year old, please tell us what operating system you are running, and any other information that would help understand what is going on.
    If you do get the keyboard to work for a short time, long enough to post back, please unlock the "caps lock" button.

  • Wireless FN key enable/disable not working

    Hi, I have Toshiba C660D-1F2 PSC1Ye-02N00PGR. The poor thing had a taste of water, but it survived all except the keyboard. The laptop is originaly from Austrija/Germany, but the sacend hand keyboard came from Croatia (QWERTZ with croatian extra letters). After installing all the drivers everything works but the FN keys. If I have Value Added Pack installed I get the flashcards but then the FN keys are inoperable. When I remove VAP, FN keay work all except for wireless and then I can not activate it. Please some halp or info. Thank you.

    I installed TVAP Version: 1.6.0130.640204 and everything works now .. sorry if I bothered you but before I tried all possible tvap versions for my model ad variation of it.

  • 1415 fnw printer wireless connection extremely slow or not working with OS X, works with windows

    The wireless connection to the printer is either extremely slow or not working at all on OS X Yosemite.  It shows up in the list of printers in Bonjour in Safari, and I can connect to parts of the web interface if I wait a very long time.  However, I cannot add the printer as a new printer in System Preferences even though the printer shows up.
    I have upgraded to the latest firmware.  The WiFi indicator on the printer is on, "green", and it has a reserved IP showing up in my router (ComCast).  It seems that Windows machines can printer to the printer wirelessly without a problem.
    Any help appreciated.
    Stephen
    This question was solved.
    View Solution.

    Hello @sscotti,
    I would like to assist you today with installing your wireless HP LaserJet Pro CM1415fnw Color Multifunction Printer on your Mac OS X 10.10 Computer. Now you indicate in your post that this printer works fine with Windows computers, and you are able to 'see' the Bonjour printer on your Mac. Therefore, the issue that you are experiencing is not network related. Rather, I do believe that you are experiencing a driver conflict on your Mac OS X 10.10 computer. Can I please have you run the steps below to resolve this issue.
    Step 1: Uninstall Drivers and Software:
    First, I'm going to have you 'clean up' your Mac OS X 10.10 computer to verify that any trace of your Laserjet printer is gone so we have a nice clean slate to work with. Please click here and when the website opens select the drop down for 'Mac OS X v10.6, OS X v10.7, OS X v10.8, and OS X v10.9' as the steps are the same for Mac OS X 10.10. Run the appropriate uninstall steps for the method in which you originally tried to install your printer: Apple Updates, or the HP Driver download.
    Once the uninstall is complete, please proceed to the next step.
    Step 2: Verify and Repair your Disk Permissions on the Mac:
    Open Macintosh HD and go to Applications
    Go to the Utilities Folder
    Open the Disk Utility
    Select the Hard Drive volume you are using (usually on the left)
    Select Verify Disk Permissions
    Once that process is done, select Repair Disk Permissions
    Step 3: Check for Apple Updates:
    Go to Apple
    Select System Preferences
    Select Software Update
    Click Update Now
    Install your available updates
    Restart your computer
    Step 4: Reinstall your Software and Drivers:
    Please click here to download the appropriate Mac OS X 10.10 drivers for your HP Laserjet printer. 
    Once the website opens select the 'download' button on the top left
    Once the download has completed, please follow the onscreen steps to reinstall your printer.
    Once the reinstall is complete, test the print and scan functions to ensure that your printer is functioning as per normal.
    Please respond to this post with the result of your troubleshooting. Should you still be experiencing issues there are additional steps I can have you run through. I look forward to hearing from you. Good luck!
    X-23
    I work on behalf of HP
    Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
    Click the "Kudos, Thumbs Up" on the right to say "Thanks" for helping!

  • Wireless keyboard connected but does not work.

    My wireless numeric keypad is connected to the iMac, but does not work.  Wireless keyboard and mouse are OK.  Tried connecting/disconnecting and restarting the Mac to no avail.  Everything was fine yesterday.  Any suggestions?

    Try a SMC reset (could help, cannot hurt):
    Intel-based Macs: Resetting the System Management Controller (SMC)
    Barry

  • Wireless Lan using WPA 2 crypt is not working under windows

    Hello,
    is it a known problem that i can not connect to my WPA2 crypted WLAN ?
    if i set up a non-cyrpted WLAN it works quite well, but not the WPA2 way.
    Is there a workaround ,bugfix or whatever, or do i have to wait for newer drivers ?
    Best regards
    fidel

    ok, problem is solved. thx again.
    the only thing was really to get a windows/microsoft
    patch for wpa2 support, which is linked in the wikipedia article.
    (only available after succesful genuince check).
    After that my crpyted wlan worked without problems
    shame on me that i havent checked that before.
    best regards
    fidel

  • First time working with 802.11n, not working properly?

    Hello,
    This is the first time I use 802.11n in my network there is only one AP1141 but the clients don't connect at 802.11n rates, instead they connect at data rates as low as 11 Mbps. At the begining they connect at 144 Mbps but immidiatly it decreases to 11 or 12.
    Many of our wireless clients in the company are Intel(R) WiFi Link 5100 AGN.
    Any comments?
    AIR-AP1141N-A-K9  
    AIR-WLC2106-K9
    6.0.182.0
    Let me know if more info needed?
    Thanks

    Hi George,
    So you suggest to keep only WPA2/AES?
    Regarding the coverage area keep in mind this is a really small 4 floor building with an AP floor floor, I installed only one AP1141 in my floor and kept the AP1131 in the other 3 floors, I might reduce the power to half since I don't need them working at full power unless I need coverage in the stairs in order to enforce roaming to IPPhones. Also, I don't want to bond channels on 2.4 because I read that as a recomendation in a Cisco's document (anyways I did not find how to do it in 2.4, wuld be a nice tip if you tell me how just in case) so 144 Mbps would be great as long as it works properly. I did not experienced these rate hoping until I enabled this AP1141.
    And yes most of the clients that reported issues are Intel (engineering team, haven't checked the rest yet).
    Regards!

  • 802.11n not working.....6hrs of frustration!!!!!!!!!!!

    I've spent basically all day yesterday on the phone with Apple tech support and even took my unit to an Apple store with no conclusion yet. Here's the deal...
    I have a PC laptop (Windows XP SP2, non wireless)....D-Link cable modem running to my 802.11n base station.....then my base station running to my PC laptop. I get service fine on the laptop. In the same room (10 feet away) is my Powermac G5 (OSX 10.4.8 and all current software updates) with a airport card. I'm in an appt building so I know my airport card is working because I'm picking up other networks from other tenents. I have a green light on the base station but I can't connect for the life of me on my G5. I even connected the modem/base station to my mac and it recognizes it through the airport utility and I was able to name it and give it a password but even directly connected to my G5 my wireless card isn't picking up the signal..........PLEASE HELP!!!!!! Forgot to add....I took the base station to the apple store and it worked there! Do you think it's the D-Link modem?

    The Airport Extreme defaults to a 10.1.1.x address.
    Most PC-Based Wireless hubs distribute 192.168.1.x
    addresses. Set your Airport Extreme to redistribute
    192.168.1.x addresses, and you will be able to
    connect.
    MacBook T2700
    2gHz, 12GB, 160G Windows XP Pro Dual
    Boot with latest OSX
    ummm...no..that should not matter at all

  • HP Laserjet 1010 & Wireless printing via Airport USB - Not working in SL

    Hi There,
    After just upgrading to Snow Leopard on my MacBook I tried printing wirelessly to my HP Printer, but no luck!
    Printer: HP Laserjet 1010
    Connected via: Airport with USB cable
    Snow Leopard recognises the printer and is fine to print when the printer is connected directly to the MacBook via USB cable, but:
    When I set up wireless printing, it finds the printer (via Bonjour) but simply will not print. The print monitor gets to 24% or so of the file processed and then just stops & fails.
    Everything was fine under 10.5 Leopard. It seems it should work, but no printing occurs! Any ideas?
    Many thanks,
    Paul

    I had a similar-sounding problem with my HP1012.
    The fix:
    a. power-cycled the Airport Extreme.
    b. Updated firmware.
    c. Select Print in an application.
    For an extended discussion of what I did see here - some of this may help:
    http://discussions.apple.com/thread.jspa?threadID=2142906&tstart=60
    Actually, at this point I have two printers connected: Airport Extreme ->USB powered hub ->2 printers. One is the HP1012, the other is an HP 4300 series inkjet. Took sometime to get it right, the first hub I tried apparently was not powered enough. In that vein, one earlier thread (a response to one of my posts) pointed out the possibility that the AE -> printer USB connection might not be adequately powered, and to try using an intermediate hub. Assuming your AE is performing properly in all other respects, don't rule out a cable or other printer connection issue even if the setup was working properly before.
    stan

  • [SOLVED]wlan0 connects to wireless network, but internet does not work

    I have a Compaq Presario A900 laptop just installed Arch on it, went through the wireless Wiki and also checked this thread: http://bbs.archlinux.org/viewtopic.php?id=65467 (similar issue but I don't use any proxy). It has Broadcom card, 4311 Rev 02. I tried both the b43-firmware and broadcom-wl AUR packages and b43 works with my card.
    I have tried with the shell to connect but "iwlist wlan0 scan" always returns no results. (Yes, I did try ifconfig eth0 down first as well before bringing wlan0 up). So I have tried wicd and it worked to connect me to my wireless network which uses WPA, and signal shows ~80% strength, however ping google.ca, nothing works as far as connected to the net.
    Any output I should show I will if I have forgotten, thanks very much for your help!
    Last edited by colbert (2009-05-27 00:40:48)

    Thanks for your help hokasch, however it was a result of needing to reboot and have proper daemon in rc.conf, and it has been working great last few days Thanks!

  • Macbook CD2 802.11n not working

    I have a macbook (cd2) and it wont connect as a 802.11n to my linksys router that has 802.11n. i can get the Atheros ar5008 to connect as N while in my mac partition, but i cant get it to connect while i am in XP. i tried reinstalling the latest driver, and deleting all the "preferred networks," but it's not working

    Boot Camp Beta 1.2: Windows XP (SP2) unable to connect to 802.11n wireless router or AirPort Extreme (802.11n) Base Station
    Relevant previous discussion.
    iFelix

Maybe you are looking for