WRT310N Setup issues after firmware update and factory reset

Hi Everyone,
I recently updated my firmware to v2 on my WRT310N and found that I could no longer connect my PC to my router. Whenever I run the setup software that came with the router it goes through all the steps but errors out when it looks for the router. I think the error number I am getting is 322.
I tried to reset the router to the factory defaults, but I am still having the same issues.
When I plug my Cable modem directly into my PC I have no issues and have full internet connectivity. I have tried to navigate manually to the 192.168.1.1 to do a manual setup of the router but I can't get to the router main page.
I'm running windows XP SP3 and I had no issues up until I did the firmware upgrade. I can't think of what I am doing wrong and am stuck.
Any thoughts?

Make sure that the cable modem is connected to the Internet port of the router. Your computer should be connected to one of the 4 Ethernet ports on the router. If your computer is connected to the port 1 of the router then port 1 light on the router will lit up. Also make sure that the Power light on the router is steady and not flashing. If the power light on the router is flashing then try to reset and power cycle the router again.
Once the power light on the router is steady then check the IP address of the computer.
Go to Start >> Click Run >> Type cmd and click Ok. You will get the command prompt window opened. In the command prompt type ipconfig and hit Enter on your keyboard. You will see the IP address of your computer. The IP address of the computer will be like 192.168.1.xxx and Default gateway will be 192.168.1.1.
Now open the Internet browser and in the address bar type the number 192.168.1.1.
It will ask you to enter the User name and password for the router. Leave the user name blank and in the password type admin. It will open the Linksys router setup page.
Under the setup tab you will find Mac address Clone sub-tab. Enable the MAC addres clone and click on the button Clone my PC's MAC. Save the changes. Try to access the Internet on your main computer.
If not able to access the Internet then unplug the power cable to the router and modem. Plug in the power to the modem first. Wait for a minute and then plug in the power to the router. Try to access the Internet.
Once your main computer is able to go on line then you can change the wireless settings of the router.

Similar Messages

HP Slate 21 audio issue after KitKat update and reset

I have upgraded my HP Slate 21 from JB to KK. Now the sound quality is very bad!
I came directly from xxx.11 kernel and made factory reset but didn't get a good result. Please how can I fix this tremendous issue?

Hey @PauloTxR ,
Welcome to the HP forums.
I understand you're experiencing issues with sound quality on your Slate 21 PC.
Please review the following thread: HP Slate 21 Kit Kat OTA Update Fix for Audio Quality and LAN Connectivity.
This fix will resolve audio issues of a software nature resulting in the KitKat update. If your issue persists after applying the specific update mentioned in this thread and have done a factory reset, the issue is likely hardware related and not the result of the KitKat update.
If you have done the above and continue to have problems please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the following link to get the support number for your region: Phone Assist Worldwide.
Thanks.
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

Numerous issues after firmware updates

After installing the latest firmware updates I've noticed several issues develop. Firstly, the keyboard and mighty mouse have become less responsive. Particularly within certain applications, for example in iPhoto there is so much latency with the mouse that it is nearly impossible to scroll across an event icon so that it will display the photos within the event. Or in the few games I play the mouse scrolls with a very jerky motion.
Safari has also not been working well since the update. Certain links (java links maybe) simply no longer work. Or even within this forum, Topics are no longer displayed. I had use Camino to view these forums.
The only reason I suspect that these issues are related to the firmware updates is that all of these issues arose immediately after installing the firm ware updates.
So far I have repaired permissions and used OnyX to run all of the maintenance scripts and empty all of my caches, but no luck.
If anyone can suggest something more to try or provide any insight, that would be great.

Not only these issues, but my iMac has reverted to its original problem of having random freezes. Twice now I have had the screen completely lock while my music/video continued to play in the background, forcing me to force re-start and lose work.
I don't have a clue what Apple thought they were fixing but if anyone knows how to downgrade firmware or if it's even possible please post up!

Early 2011 Macbook external display issues after firmware update

I have a 2011 MBPro 15". After performing the firmware update in late April, I have continual issues when I connect my monitor. The screen is blank and I can move the mouse tap the keyboard etc. The display may come up for a scond and then it will close and the machine goes back to sleep. More wiggling and the process starts over.
If I raise the lid it may bing up the external display. Restarting is the only sure fix.
I also was unable to make a presentation today because the projector I was connected to would not show the MBP display.
I tried all the key combinations, detect display etc. and nothing.
Can I somehow go back to the prior firmware? Other solutions?
SMC Version (system): 1.69f1
EFI Driver Version: 01.00.521

I recently did a software update to my MacBook pro and had a similar issue, on restart it gets to the apple logo then just shuts off, after multiple hours on the phone with apple care they told me that it was coincidence that it happened at the same time as the update and it would be costly to repair as it was either something to do with display or logic board. I took my MacBook into my retail location I bought it from and was told that they have had MULTIPLE people bring in macbooks with the SAME issue (I live in a really small city so the amount of people is quite large proportion wise) and that they could fix the issue by remotely resetting the MacBook at a cost of $130-$150. Relatively cheap considering what I was fearing, but if this is a common problem related to Apples update why are we paying to fix it and why is apple support saying its something major???

SA520W Configuration Access Issues After Firmware Update

The problem I'm having is a minor one, but a problem nonetheless. I'm new to this company and took over from the previous IT guy who was let go so he's the one who set all this up. We are using a Cisco 1841 which was provided by our ISP, and it is plugged in to the WAN port on the SA520W. The SA520W has the static Wan connection info and it is what makes the connection. Initially, we were able to access the SA520W configuration page with either it's default gateway 192.168.5.1 or with the IP 204.101.24.67, which is the static IP in the Optional WAN Port settings of the SA520W. After upgrading our SA520W from 1.1.42 to 1.1.65, I am no longer able to access the router using 204.101.24.67. I can only get in using the default gateway (192.168.5.1). The Optional WAN port is not in use and never has been which confuses me - I took screenshots of all the settings before the upgrade and nothing has changed at all. I guess I'm confused as to how I was initially able to access the router using 204.101.24.67, and why it stopped working after the firmware upgrade. Does anyone have any suggestions?

I re-read your original Post; are you not using the WAN port also? Did you try and remote in from a switch attached directly to the WAN/Optional WAN port? I am asking as I have almost the exact same setup using an 1811 which is NATing the SA. I could not reach it as the one-to-one NAT on the 1811 was not set correctly. I also went through the firmware upgrade and experience the same issues you are. I had the CISCO account with WAN access, and the upgrade removed that (after a lot of scratching). However, my real problem was also the routing on the 1811. I eventually had to get the guys to do a one-one NAT and remove all ACL and rules, but that does not mean it can't be done with it either. Try reaching it with a switch or cable and see what happens.

MacBook Battery Shutdown issue after firmware update - anyone reinstalled?

Has anyone tried re-loading their OS? I have this issue too (though my battery lasts about 30 minutes) and this it powers down. I called apple (my SN starts with 8609) and told them I had a battery issue.
They were not much help - they indicated to me that I am over my 90 days for phone support and that I would have to bring my battery in to the store to have it tested. They went further to say if it is a firmware issue and not a battery that is technically software and I would be charged $50 for battery testing if it passed. And that if there was actually a battery issue they would replace under the 1 year hardware warrenty.
My dilemma now is should I try and wipe/reinstall the base OS (which I was told will undo the firmware upgrade).
I thought I would check here to see if anyone tried this before swapping battery???
I seems that the firmware update caused the problem but I am not sure if the battery is still good and the firmware is just crap or if the battery might still be ok. Has anyone wiped/re-installed the os and fixed this issue?

thats good news then in my case if its the logic board. The cpu whine has been driving me nuts(being excessively louder then most other macbooks with the whine) so I've been wanting to get the logic board replaced anyways.
Dont worry about the applecare though since we all should have it within the 1 year warenty still so all repairs should be covered.
Imo I'm considering purchasing the extended applecare protection plan if i can come up with the money( $249 is a bit steep for me) to get anouther 3 years of warrenty service expecialy with all the problems macbooks have been having.

IPhone 5 constant crashing after iOS 8.0 Update and Factory Reset!!

So...thanks Apple! You completely bricked my phone with the most recent update.
Status since 9/17....
* Performed iOS 8.0 update via iTunes on my iPhone 5.
* No issues whatsoever until Saturday 9/20 around 5pm
* Phone starts reseting incessantly about every 5-10 minutes.
* Performed hard reset. No luck.
* Uninstalled apps since update. No luck.
* Noticed upon some crashes the screen goes totally janky (maybe graphics chip failure?)
* This morning decided to run full factory reset, hoping all would be fixed.
* Resetting issues start almost immediately and are continuing.
I'm not too excited about going into the Apple store given all the iOS 8.0 issues and fan-boys buying the newest 6 (holding out for 6s if possible).
Has anyone else out there had a similar experience?
Thank you in advance,

SO, the constant reboots have stopped, but now have significant charging issues.
* % charge doesn't increase on multiple different charging cables
* hard reset doesn't solve

My time capsule isn't responding after soft, hard and factory resets... what next??

My time capsule isnt responding after I've done soft, hard and factory default resets I'm afraid Ive lost my data... what else can I try to get my time capsule to respond??

What is the front LED doing?
If it is solid amber the drive is dead.. there is no way to recover the Gen2 drive unless you remove it and pass it to data recovery specialist along with your wallet, credit card and bank account.
TC is not designed as a file server so I just hope you were not saving your itunes or iphoto store on it without a backup.
If it is flashing amber.. plug it into a computer by ethernet in complete isolation from the network.
Use the old airport utility if you actually are running Lion as per your profile.
How to load 5.6 into later Lion & ML
1. Download 5.6 for Lion.
http://support.apple.com/kb/DL1482
Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
Leave the package open on the desktop so you can see the file. AirportUtility56.pkg
2. Download and install unpkg.
http://www.timdoug.com/unpkg/
Run unpkg on the desktop.. If your Mac refuses to run the software, because it wasn’t downloaded from the Apple store, go to security in preferences and allow other software to work.. this is limitation of trade methinks. You can set back later if you like.
Now drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. in finder, open the new directory, drill down.. applications, utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
You cannot uninstall version 6 (now 6.3 if you updated) so don't try.. and you cannot or should not run them both at the same time.. although I have had no problems when doing so.

Updated and factory reset macbookpro, how to recover lost videos from the application "front row"

Desperately need an answer, every response is appreciated.

What do you mean you factory reset it?
If you erased & reinstalled the OS then I'm afraid to tell you that those items are gone.
A data recovery company may be able to recover files but it could be difficult or impossible depending on the disk type & how it was setup.
You need to avoid writing any new data to a disk that will be recovered from to stand the best chance of finding deleted files. Power off the Mac & leave it off until you have decided on a course of action.
Don't you have any backups at all?

LaserJet 1102W lost connection to network after firmware update and can't reconnect.

I have used the LaserJet 1102W on my Wifii network for some time. I use MacOSX 10.7 on one laptop and OSX 10.8 on my new Retina Macbook Pro. I updated the firmware to get access to ePrint and lost wirless connections. I have tried many times to reestablish network connection as instructed thru System Preferences and continue to get the response that my Wep Key is invalid. I have many items using the Wep key including apple tv, phone, ipad and it is the correct wep key. My network is Wep 128. Is there some way I'm suppose to split the key between the 4 available wep key spaces? My router is a Linksys WRT320N, Mac Book Air running 10.7.4, Mac Book Pro running 10.8.2. I have been trying to setup the network wireless with the Mac Book Air. I can print with both computers via USB.

I updated a P1102w that we have here to firmware version 20120814 and haven't had any problems with it. I set a static IP and set the DNS to a preferred of 8.8.8.8 and an alternate of 8.8.4.4, and haven't had a problem with anything from a Windows system. I ran into a problem printing from Safari on a Mac running OS 10.8, but that was the only program with the problem. I even turned the printer off and back on several times to make sure the IP settings would stick, and they have. If you've done that and are still having problems, try power cycling your entire network. I'll link a document that will help to get the printer on the network steadily below. If you are still in warranty, HP may replace the printer at no cost to you. I'll link the information to get in touch with them below. The link will take you to a form to fill out. Once you fill it out and it is processed, it will give you the printers warranty information, a case number, and the phone number to call.
Printer Does Not Maintain Wireless Connection:
http://goo.gl/YoJ7g
HP Technical Support Case Call Form:
http://goo.gl/w7Hgh
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Stacks issue after firmware update 1.2, won't fan anymore only grid.

This issue was resolved when I updated to the 10.5.2 Leopard OS but now that I've updated the firmware with the most recent update yesterday the stacks function in the dock went back to just being able to show the grid format and when I choose the list format it comes up in a standard list (menu) view not the nice new fan view.
Has anyone else had this issue yet? Has anyone been able to fix it? I can see from the install log that there were errors and it looks like they were specifically with the dock/stacks portion but I'm not code savvy enough to know how to fix them.
Any help or suggestions would be greatly appreciated.

Well, at the risk of insulting your level of expertise - is your Dock on the side instead of the bottom? There's no fan available with side-docked Docks, either in function or the popup menu.
If that's not the case, try trashing the Dock's plist and see if that makes it behave.
Please keep in mind we see many, many beginners or otherwise naive users asking questions which have simple answers, and no insult is intended when a suggestion is made that you've already tried; it's hard to assess a writer's knowledge level. When your original post said "and when I choose the list format it comes up in a standard list (menu) view not the nice new fan view" it made it hard to determine your level for 2 reasons: You referred to the "new fan view" which is not new in 10.5.2, the upgrade you said you just installed, and if you "chose the list format" why would you expect it to show you a fan view? That's probably why Bruce told you to select "fan view". It was probably just a less-than-perfect sentence on your part, but you might be able to see, in retrospect, that it sounded a little newbie-ish.
Bruce tried to help you and we can only hope that your reaction does not make him hesitate to help someone else lest he get snapped at again!

N8 - Picture Browser Issue After Firmware Update

Since I´ve updated to PR1.1 I have a lot of tearing and blurriness when I see my pics at max zoom in the phone´s own pic browser.
Pics viewed in my PC are just fine.
I´ve tried to reinstall the FW 2 times already, but the problem remains.
Details from my FW version:
PR1.1 013.016.C11.01
Language: 013.016.34.01
PC: 0599221

I also have the same problem. I have two Bluetooth headsets, Nokia BH-101 and Sony Ericsson MW600. Both worked just fine before Anna update. But after installing ANNA, both hands free units giving problems. After couple of calls its simply not responding, and phone get stuck and touch screen not responding to any commands.
After disconnecting the BT handsfree, sometimes phone starts to work fine but in rare cases, it shows as a headset connected even after disconnecting the BT headset.
And when you restart the phone, its start working again with BT. But not for so long. This is a real headache. Please give a solution.

IPOD Software update and Factory Resetting

Hey,
So my Ipod touch needs to be reset and I cannot load the backup of it back on. If I purchased the iPod touch 3.0 update the first time around, will I have to repurchase it again once it is reset, or will it install it again? Thanks

If you use the same account as when you bought the update, iTunes will remember your purchase and download the firmware during the restore process.

Bluetooth w/ voice commands is not working correctly after 2.2 update and factory default.

I have been having numerous problems with my phone and now a problem with the Bluetooth. I have a Sony Xlopd Stereo in my car with built-in Bluetooth capability. I have been able to use the phone connected to the Sony flawlessly for several weeks. On an in coming call the Caller's name and the ringer would go through the speakers in my car. When I wanted to place a call from the car I would press the Bluetooth button on my stereo, this would launch the voice command program on the Droid X and output the voice commands responses through the stereo and then dial the phone number I was trying to call. Then I updated the phone to 2.2 and still maintained all the same Bluetooth capability. However, after having other problems with the phone after the update I decided to do a Factory Rest. After the rest it seemed to clear up some of my issues; except now when I re-paired the phone to my Sony stereo I have lost a lot of functionality. For example, now when a call comes it does not announce the caller or ring through the stereo. When I try to place a call through the stereo, the voice command program is no longer launched on the phone and it will not place a call. I have to initiate the call through the phone itself and then the Bluetooth automatically picks up the call. I have tried to wipe the paring from the phone and stereo and pair again with no luck. I have also checked the volume settings and most settings on the phone. This frustrating when trying to place a call. I would not be so bad if I never had the capability, but now knowing that it was possible at one time I want it to work again.
Does anyone know if this functionality was lost after the update and my phone was still "stuck" between 2.1 and 2.2?
Or is there another problem with my device that can't be resolved?
I am open to any advice, since Verizon will not replace my phone that has signal and reception issues dropped calls, reboots randomly among other things and now this issue even though I pay $8 a month for warranty and pay my bill with four other phones.
I am really hating the Driod X with all the flaws and inconsistency..I miss my Blackberry.

ridgey115 wrote:
I was having the same problem with my X right out of the box. Using a Motorola T505 handsfree device. Turns out that it acts exactly as you describe if the screen lock security is enabled. Once I disabled that, it worked fine. It does take a few seconds for the voice prompts to activate, but other than that it works. Not sure if you use the extra screen lock security, but if you do, you may want to disable it.
Its been so long that I thought about that issue but that is correct, when the device is locked using the password or swipe feature it does restrict the voice dialed from activating from bluetooth...

Wifi keeps scanning and dropping even after connected to home network. Never had this issue until the update, and now my phone runs slow and terrible. Horrible update!! Any ideas on a fix?

Wifi keeps scanning and dropping even after connected to home network. Never had this issue until the update, and now my phone runs slow and terrible. Horrible update!! Any ideas on a fix?

It's important that you have a steady WiFi connection, ZealousEdge. What phone do you have? Is your phone unable to connect to any WiFi network? If you can, please try deleting the saved WiFi network and re-adding it.
AndreaS_VZW
Follow us on Twitter @VZWSupport
If my response answered your question please click the "Correct Answer" button under my response. This ensures others can benefit from our conversation. Thanks in advance for your help with this!!

WRT310N Setup issues after firmware update and factory reset

Similar Messages

Maybe you are looking for