WRT54GL Admin Problem

When i go to edit some settings on my router, so port forwarding or something, and i go to click save settings it brings up a error. It says
'This Web Page is not available, The website at null might be temporarily down or it may have moved permanently to a new web address.
I need to change my NAT settings, but i can't because everytime i press save it comes up with that. Does anybody know how to fix it?

This is often caused by a communication problem between the the router and computer.
Try this to fix the problem:
You do not need an Internet connection. The router's "web pages" are built into the router.
Use Internet Explorer, it usually works.
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall.
If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem. If this does not work, try the following with Zone Alarm: Open the ZAISS control center, go to Privacy, then temporarily turn off Ad Blocking and Cookie Control, and see if that fixes your problem.
If you are using Noton Internet Security with the Add-on Pack, be sure to turn off the Pop-up Blocker, and the Ad blocker. Some users have reported that they needed to uninstall the entire Norton Add-on Pack.
If the above fails, disconnect your modem from the router, and try again. If this corrects your problem, then most likely you have a "modem-router" rather than an ordinary modem. Report back with this problem, and also state the make and exact model number of your modem (not the router).
If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.
If all of the above tips fail, then reset the router to factory defaults: Power down the router and disconnect all wires from it. Wait one minute. Power up the router, allow it to fully boot (1-2 minutes), then press and hold the reset button for 30 seconds, then release the button and allow the router to reset and reboot ( 2-3 minutes). Power down router and your computer. Wait one minute. Connect one computer, by wire, to a LAN port on the router. Boot up system. It should work, however, you will need to setup the router again from scratch.  If you saved a router configuration file, DO NOT use it.
If the reset does not fix your system, then you need to download and install (or re-install) the latest firmware for your router. After the firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.

Similar Messages

  • RT31P2 + WRT54GL + Vonage problems

    Hey guys, I've been having a recurrent issue for a while now, and lately the problem has gotten a lot worse.  Before I describe the problem, I would like to explain the exact set-up that I have to better explain the situation. (I have had this set-up for a good 4-5 years now)
    - I have vonage phone service, and they provided me with the the RT31P2 router for use to connect my phone lines to. Since this is not a wireless router, I went out and bought a WRT54GL, so I can get wireless access for my laptop.
    - In order to set up the two routers, I connected the ethernet cable from my cable modem and plugged it directly into the WAN of the RT31P2. I took another ethernet cable, plugged it into one of the ethernet ports on the RT31P2, and plugged the other end into the ethernet port of the WRT54GL.
    Note: Before I did the above connections, I disabled the DHCP on the WRT54GL and changed the starting IP address to 192.168.15.2. Also set up a secure password enabled network.  For the RT31P2 router, all the settings remained the same, and it's IP is 192.168.15.1.
    - For the most part, this set up has been absolutely fine. My home phones would work with no static, no dropped calls, etc. I have one PC that is hooked up via ethernet on the RT31P2. Three laptops that connect wirelessly to the WRT54GL.
    Problem:  A couple of days ago, I noticed my internet speeds became drastically reduced on the PC's that are connected via WiFi. (Normally, I would get speedtest.net results with a range of download: 9-10Mbps and upload: ~ 0.54Mbps.) The speeds I was getting instead were close to 2Mbps (download), and even lower for upload. I isolated the problem and found out that only PC's connected via WiFi were experiencing this slowness. The one PC connected via ethernet was still getting its average normal speeds. (Currently, I hooked up two laptops to the RT31P2 via ethernet and disabled the WRT54GL router, and its running at normal speeds).
    I called up my ISP to come and take a look and see where the proble might be, and everything on their end seems to be fine. Since they only provided the cable modem, anything extra has to be taken care of the party that is responsible for it. So basically, everything via direct connection from Cable modem, or ethernet connection from RT31P2 is good, but my wireless connection from WRT54GL is no longer usable because of the slowness.  I have not changed the above-mentioned set-up at all, there were no hardware changes, nothing that can explain why all of a sudden devices connected to my wifi would be this slow. This issue seems to occur maybe 2-3 days every two weeks or so, but currently, it's been going on for about a week.  I think I also had a similiar problem like this sometime last year, and it took a long long time for the wifi to become stable again (close to a month). At that time, my ISP said the same thing to me - that there is no fault on their part because the signal strength was good on their end.
    So does anybody have any idea/know why this might be happening with my wireless router?
    *Also, another issue with vonage phone service - right when the wifi started acting up, I noticed that my home phone was getting a lot of static, making calls unbearable. I would get a dial tone, but it was absolutely impossible to carry out a conversation with that amount of static. So I called Vonage this morning, and we spent a good amount of time trying to isolate the problem.  What we came up with is the fact since I kept my cable modem and routers literally on top of each other, that it was causing some type of interference. When I moved all the devices away from each other, the static disappeared (only a little bit remained, but not a big deal). However, after I hung up the phone with vonage support, I realized that the static was not gone because I moved the routers away from each other, but the fact that the static only occurs if i have another ethernet cable plugged into the RT31P2 (which is the router where the phone lines connect to), where the other end of ethernet cable is connected to a PC. Any ideas on what might explain that? Do you guys think there is a correlation between the static on the vonage and the wifi problems, even though they are on different routers..?
    I know it's a long message, but I would really appreciate if somebody would take the time to go over this post and help me out. Thanks a lot to anybody with suggestions.

    Hi rsayeed   and welcome to the Cisco Home Community!
    The RT31P2 is now being handled by the Cisco Small Business Support Community.
    For discussions about this product, please go here.

  • WRT54GL Internet Problem

    Hi all, since I got my WRT54GL my internet became very laggy, having spikes and very slow download speed. Also it randomly discconects and I have to manualy go to router's home page -Status - and press connect botton 2-3 times in order to connect. 
             It's the same thing regardles of the number of PC connected to it, or the method of connection (wired/wireless) . Also I should mention that my internet service provider is a good one , before this router I hadn't have any problems.
         I run different OSs on the PC's and here are some of the router's settings : 
        Firmware Version: v4.30.13 (latest I think)
    Internet Connection Type : PPPoE
    Connect on Demand : Max Idle Time   Min.
     MTU : 1300 ( tried 1350 -1400)
    Security Mode : WPA Personal
    WPA Algorithms: : TKIP
    Group Key  Renewal : 5000 sec
    Beacon Interval: 75
    Fragmentation Threshold 2304
    RTS Threshold:  2307
      Firewall Protection:  Enabled
     Block Anonymous Internet Requests  & Filter IDENT(Port 113) Checked
    DMZ / QoS Disabled
     UPnP: Enabled
     Please help me if you can Thanks.
           Also , a second ,unrelated question : Can I make another account for the router's homepage ? like a guest account or something , and if not what is the purpose of the User Name on the login page ? 
    Thanks for reading  

    - Check the option "Keep Alive" and click on save settings...Now,check.
    - You can not create another account on the router homepage.
    - The password is created for the router's setup page,so that no one can manipulate with the configuration of the router..By default the router password is "admin"..You can change the password under Administration tab. 

  • Help with Admin Problems

    Ok so I have been blessed with the most unlucky of situations anybody could Imagine. My Dilemma is that I now have a new Macbook Pro running Mavericks 10.9.4 as my old one is many, many years old. Now the problem is that I need to unlock the gold padlock on the old computer running 10.5.8 but there is no admin account? All of the users say standard and I thought I had used to be the admin but now its gone. So I looked up ways of fixing the problem including one specific one: Restart computer, Hold command+s, type: "mount -uw /" then: "rm /var/db/.AppleSetupDone" then: "reboot" and had gone through all the settings and set up a new account but the account it made is still only a standard and not an Admin account! And since I still don't have an admin I cannot even delete the new standard account. My poor old Mac is running out of memory and disk room. Any ideas on anything I can do as I no longer remember where the startup discs were put, cannot gain access to any admin privileges, can not unlock anything I need to get to, and have not tried an Apple store yet as I heard they will not do it for you. Anybody have suggestions as I can't get any of my important files off my old mac or even activate our time machine cause it requires the admin info as well

    The first user on Mac is also has administrator rights, so use your password for the account.

  • ARD Admin problem

    I'm running ARD 3.4 in a school with 26 iMacs from early 2006 in a lab. Everything was working fine until I had to replace two machines due to hardware failure. I replaced them with the same model computer, restored them from the same image that the rest used, and called it good. I administer ARD from another iMac, early 2008 20" in the building. I went to install some software and found the two I had replaced not working, call them #1 and #3. I removed them from my list, ran the scanner, and found the machines were simply using different IP addresses, so I re-added them to my list. ARD works as usual for all the machines except 1 & 3, listing them as offline, but I am still able to control them (any other tasks fail because the computers are "offline"). I've gone through every setting, both on the machines, and in ARD and the only difference I can find is that ARD reports 1 & 3 as being administered by a computer with a different IP address than the others - I've pinged this IP address and gotten no response. The working computers also have a green light next to the admin machine name, while 1 & 3 do not. I click the edit button at the bottom of this page, but it doesn't actually let me edit anything, regardless of which computer I'm checking.
    Has anyone else run into this problem? Any suggestions?

    Hi jhana,
    I've been combing the boards because I too am having this very same kind of thing happen.
    In my case, I moved and have been attempting to recreate the office I had back in AUG 2010. Started setting it all up in January and was delayed due to a lot of hardware failures. Am finally getting around to setting up ARD and my computers are not working with ARD as they did in the past. Many are showing up as Offline. I decided to throw away the prefs and thought it would give me a fresh start, but now many computers on the network are not even showing up!
    Misery loves company, but I sure would like to solve this and get happy.
    Suggestions anyone?
    ARD 3.4 Administered from an iMac PowerPC G5, and the Ethernet & Airport network has 3 more iMacs, a MacMini, and two PowerMacs, and a PowerBook G5, and sometimes an iBook. Things were working great before I moved. Network is configured a bit differently that before, but since I set it up, file sharing seemed to be working OK, so then went I went to set up ARD 3.4 things are not right.
    Why?
    Thanks in advance and so long for now, TOM

  • Server Admin Problem - File Sharing fails to load

    We recently switched over from a 10.4 server to an Intel Quad Core Xserve running 10.5.8. Things seemed to be working for about a week but now The File Sharing part of Server Admin fails to load. After spinning for a few minutes I get a kNetworkError on the File Sharing Service.
    I'm not totally through setting up all the share points so this is causing quite a problem. Otherwise the Sharepoints that are set up are working properly. The first time this happened a server restart cleared the problem. This time nothing seems to help.
    Anyone have a cure for this?

    The problem seems to be getting worse. Once the error occurs some of the other services are not available through SA either. Anybody have any suggestions, or is it a reformat and reinstall situation?

  • IP Admin Problem

    I am unable to install my printer on my MacBook 10.5.8
    I have pasted into the Terminal:
    dseditgroup -o edit -p -a admin -t group _lpadmin
    I then press enter and it asks for my password, but when I type it in nothing happens, nothing types.
    How do I enter my password if I cant type it in please?
    I have searched this forum and I cant find anyone else with the password input problem
    Hope someone can help
    Thanks

    Keep typing it in. It's not supposed to display anything onscreen when entering it in the Teminal.
    (91739)

  • Delegated Admin - Problem

    I just installed the SC 6 Update 2 all component in the same server....when i try to create a user with delegate admin i have the following error
    /opt/sun/comms/da/bin/commadmin -v user create -D admin -n domain.com -l username -d domain.com -w password -S mail,cal -H servername.domain.com
    FAIL
    *5088:Error message required. missing resource string -> norgsmd null*
    the only way to make work is if I remove the " -S mail,cal". I enable mail & cal to be use with convergence, the object exist in the LDAP because the admin user that was created with the installation has all the objectsclass needed for calendar and mail, so if I login into convergence I see the calendar and email folders...
    and then a I run the command /opt/sun/comm/im/sbin/imadmin assign_services to assign the services to all users in a specific domain and it executes without problem but without changes...the users still have the same objectclass
    the complete output of the command is :
    bash-3.00# /opt/sun/comms/da/bin/commadmin -v user create -D admin -n domain.com -l username -d domain.com -w 12345 -S mail,cal
    [Debug]: DBG:Object = user ; task = create
    [Debug]: default domain from Properties: domain.com
    [Debug]: IShost from Properties: mail.domain.com
    [Debug]: ISPort from Properties: 80
    [Debug]: Contacting : http://mail.domain.com:80/commcli/auth
    [Debug]: To servlet: domain=domain.com&username=admin&password=12345&charsetenc=UTF-8
    [Debug]: cookie => JSESSIONID=6777b671e5fb7eee49f1851ec1a3; Path=/commcli
    [Debug]: RECV: OK
    [Debug]: RECV: OK
    [Debug]: RECV: dn: uid=admin, ou=People, o=domain.com,dc=domain,dc=com
    [Debug]: RECV: nsroledn: cn=Top-level Admin Role,dc=domain,dc=com
    [Debug]: RECV:
    [Debug]: DBG: before getobjtaskargs
    [Debug]: In getObjTaskArgs for: user; create
    [Debug]: Contacting : http://mail.domain.com:80/commcli/climap
    [Debug]: Sending to servlet: task=create&object=user
    [Debug]: getObjTaskArgs Status: 0
    [Debug]: Number of servlets: 1
    [Debug]: Servlet Name: TaskManager
    [Debug]: Servlet args: task=CreateUser
    [Debug]: Servlet args: objecttype=User
    [Debug]: Valid Options Array: 8
    d, true, , false, true, user's domain, domain, ,
    l, true, , true, true, user's login ID, add_uid, ,
    F, true, , true, true, user's first name, add_givenname, ,
    L, true, , true, true, user's last name, add_sn, ,
    I, true, , false, true, user's middle initial, add_initials, ,
    W, true, , true, true, user's password, add_userpassword+confirm_userpassword, ,
    S, true, , false, true, service(s) to be added , add_services, mail={H;true;#;false;true;user's mail host;add_mailhost;#},{E;true;#;false;true;user's email address;add_mail;#}::cal={E;true;#;false;true;user's email address;add_mail;#},{B;true;#;false;true;user's back end calendar server;add_icsdwphost;#},{J;true;#;false;true;first day of the week;add_icsfirstday;#},{T;true;#;false;true;user's timezone;add_icstimezone;#},{k;true;#;false;true;calendar version - legacy or hosted domain;cal_version;#},
    A, true, , false, true, attribute to add, <attr name>:<value>, add_, ,
    [Debug]: DBG: getObjTaskArgs done
    [Debug]: servInfo len = 1
    Enter user's password: 123456789
    [Debug]: argVal =domain.com
    [Debug]: servCommand =task=CreateUser&objecttype=User&domain=domain.com
    [Debug]: argVal =username
    [Debug]: servCommand =task=CreateUser&objecttype=User&domain=domain.com&add_uid=username
    [Debug]: argVal =test
    [Debug]: servCommand =task=CreateUser&objecttype=User&domain=domain.com&add_uid=username&add_givenname=test
    [Debug]: argVal =test
    [Debug]: servCommand =task=CreateUser&objecttype=User&domain=domain.com&add_uid=username&add_givenname=test&add_sn=test
    [Debug]: argVal =123456789
    [Debug]: servCommand =task=CreateUser&objecttype=User&domain=domain.com&add_uid=username&add_givenname=test&add_sn=test&add_userpassword=123456789
    [Debug]: argVal =123456789
    [Debug]: servCommand =task=CreateUser&objecttype=User&domain=domain.com&add_uid=username&add_givenname=test&add_sn=test&add_userpassword=123456789&confirm_userpassword=123456789
    [Debug]: argVal =mail
    [Debug]: servCommand =task=CreateUser&objecttype=User&domain=domain.com&add_uid=username&add_givenname=test&add_sn=test&add_userpassword=123456789&confirm_userpassword=123456789&add_services=mail
    [Debug]: argVal =cal
    [Debug]: servCommand =task=CreateUser&objecttype=User&domain=domain.com&add_uid=username&add_givenname=test&add_sn=test&add_userpassword=123456789&confirm_userpassword=123456789&add_services=mail&add_services=cal
    [Debug]: Contacting : http://mail.domain.com:80/commcli/TaskManager
    [Debug]: To servlet: task=CreateUser&objecttype=User&domain=domain.com&add_uid=username&add_givenname=test&add_sn=test&add_userpassword=123456789&confirm_userpassword=123456789&add_services=mail&add_services=cal
    [Debug]: RECV: FAIL
    *[Debug]: RECV: 5088:Error message required. missing resource string -> norgsmd null*
    [Debug]: CLITask: status returned =FAIL
    FAIL
    *5088:Error message required. missing resource string -> norgsmd null*
    [Debug]: DBG: doOne returned code=6
    [Debug]: Contacting : http://mail.domain.com:80/commcli/logout
    [Debug]: Logout ...
    any help will much appreciated
    CA

    KenGra wrote:
    I found the problem, the default domain that was created during the installation did not have all the objectclass needed, such as calendaruser etc....Did you remember to run the "./commadmin domain modify -S mail -S cal -H mailhost" for the default domain after the installation of Delegated Administrator?
    Regards,
    Shane.

  • Shares-admin problem

    I have a problem with shares-admin application on Gnome. I've been install Samba through wiki (http://wiki.archlinux.org/index.php/Samba), and install gnome-system-tools and nautilus-share package for easy share of my files. But Add and Unblock buttons of shares-admin don't be able to press. And on nautilus-share, "Share through" is disable to me.
    Any ideas about this issue? Thanks in advance.
    Last edited by alessandro_ufms (2008-11-17 14:31:32)

    Have you found a solution to this? Or has anyone else got any idea of what might be causing this?
    I'm having the exact same problem. Shares-admin doesn't allow me to do anything (not even change the workgroup name) except for removing shared folders.
    I can share folders with no problems by editing the smb.conf file (and other computer are able to access them - so samba is working), but I can't do it from nautilus nor can I view the shared folders of other computers.
    It seems like this user has no access to samba... do I need to add this user to any group (it didn't use to be like this)?
    I know it used to work some time ago, but since I rarely share new folders I can't tell what update caused it to stop working.

  • Admin problem with WRT54G

    I am logging into my WRT54G to try to upgrade my firmware. The problem is that when I log in, I get a error on the page and it will not bring up any of the links or icons that I would use to go to Administration or check my wireless or anything. Does anyone even know where to start with this? I am using XP Pro and IE6 SP2.
    Any ideas?
    Thanks,
    Derek

    If you are getting a 401 error, the router most likely did not accept your user name and password.  The defaults are:  user name is left blank, and password is "admin"  (with no quotes).  If you changed these, then you will need to enter whatever you changed them to.  If you cannot remember what you set them to, then the only other option is to reset the router to factory defaults.  This will reset the user name and password to the values noted above.
    Sometimes this problem is caused by communication errors between the computer and router.  To correct this, do the following:
    Use Internet Explorer, it usually works.
    JavaScript must be enabled.
    Use a computer that is wired to the router.
    In the non-working computer, temporarily turn off your software firewall. Note that some Zone Alarm users have had to uninstall the firewall to get it turned off.
    If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
    A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.

  • Admin problem activating Firevault in User a/c

    Have activated FireVault in my Admin a/c & in one user a/c, no problems. However in the last a/c  , my partners its refusing to acknowledge my admin password which is valid. There's is plenty of HD space available. Any Suggestons? There's is nothing (data,photos) much in the a/c so one option is thrash it & create a new one but before I do this I just wanted to see if there's is a reason why this is happening.
    Thanks

    Hello LT
    apologies for the late reply but tried earlier via by 5S but was unable to post a reply.
    Your last Q got me thinking as when I looked at the profile last night before initiating thread the user had admin rights which I then removed, no problem. When I returned home a little while ago tonight I tried to activate FireVault using her user name & password = no luck. I tried again with admin rights = no luck. Finally I tried again using admin password but this time I changed the case of the first letter & yes it worked. Seems strange but you may have an answer. In the other two profiles I had no issue & even now re. logging in & making other admin changes the lower case version of the password works.
    We had a break-in 2 days ago & we were v fortunate. He had the iMac removed but was interrupted. Hence my FireVault activation.
    Thanks for your help. Hope this is of help to the third party who is experiencing the same problem.
    Kind regards,
    Dino.

  • From schema 1 to schema 2 migration delegated admin problem

    I want migrate from schema 1 to schema 2 the messaging server 6.2 ( jes 2005q1).
    I have install access manager and delegated admin.
    With the commdirmig I migrate the domain and schema , the messaging work correctly.
    I have a problem with the delegated admin web interface.
    The delegated don't view my domain. If I add the sundelegatedorganization objectclass I can view my domain on delegated admin but I can view user and group.
    Any Idea?
    TIA
    Bye Giovanni

    There are two very different products called "deletaged admin". The old iPlanet Delegated Admin (iDA) only works with Schema 1. The current Delegated Admin, that comes with JES3 only works with Schema 2.
    If you're using the old iDA that worked with schema 1, it won't work with schema 2. You have to install the new DA for that.
    It doesn't work with groups/lists, only with users and domains.

  • Flash Player 10 causing a Google Analytics Admin Problem

    Since I upgraded to Flash Play 10, inside the admin of Google Analytics is not working.  When I log in to Google Analytics, Flash Play 10 is a part of adjusting the dates and it is causing some type of error that I can't figure out.  All I want to do is be able to adjust dates within Google Analytics and I can't.
    It happens in the three different browsers FireFox, IE and Chrome.  I have tried uninstalling and reinstalling an older version but it still isn't working.
    The reason I believe it is the flash play is because when I open the date section in Analytics I can right click and it give me the option of 'About Adobe Flash Player" and shortly after updating I opened analytics and my browser crashed.
    I am going to uninstall my browsers to see if that will work but if anyone else has had this problem and solved it please help me out.
    Thanks

    Hi, Thanks for the feedback. Yes that does help in many cases. Sometimes updating the device drivers also.
    The hardware acceleration sometimes can't be used by every system. You can read about the system requirements and what and how it works here:
    http://www.macromedia.com/support/documentation/en/flashplayer/help/help01.html
    Regards,
    eidnolb

  • OSX 10.4.7 Workgroup Admin problem from remote computer

    I've set up for test a 10.4 server on a private network.
    On this server, I've created with Workgroup Admin some accounts for files, mail and web. I've no problem to access nd modify these accounts with the tools installe on the server, but when I try to do the same thing from a remote Workgroup Admin, I've an empty list for users and group, except the admin user.
    The fact is that i've changed the DNS setup from a dyndns account to a classical dns entry.
    Is there any correlation between the DNS changement entry and the fact that I cannot retreive my users entries in Workgroup and how restore a normal usage.
    Thanks for help !

    Are you looking in the correct domain from the remote machine?
    You may just be looking in the local netinfo domain of the server, and you need to be looking in the OD domain.
    Open WorkGroup Manager and in the top left under the 'Admin' globe you will see another small globe. Click on this and use th pulldown menu to check you are looking at the /LDAPv3/127.0.0.1 domain.
    hth,
    b.

  • WebLogic 8.1 Portal Admin problem !

    Hello,
    I use the web-based portal admin to create a portal with some deployed portlets.
    My problem is that the URL is very long (http://localhost/portal/appmanager/dse/desktop1?...) and can I create a portal with the URL like (http://localhost/dse/desktop1?....)
    Eric

    Address 7001 does't seem to be good idea for debuging, it is weblogic default address.
    try 3999.
    "Arsel" <[email protected]> wrote:
    >
    Hi There,
    I started weblogic server 8.1 with the follwing option -Xdebug -Xnoagent
    -Djava.compiler=NONE
    -Xrunjdwp:transport=dt_socket,server=y,suspend=n,address=7001
    Weblogic started successfully but when I tried to attached the java process
    from
    my IDE I got the error 'Target server failed to handshake' and in the
    weblogic
    console I got the following error.
    <22-Aug-2003 10:09:52 o'clock AM EDT> <Error> <HTTP> <BEA-101083> <Connection
    failure.
    java.io.IOException: A complete message could not be read on socket:
    'weblogic.servlet.internal.MuxableSocketHTTP@1871db
    1 - idle timeout: '60000' ms, socket timeout: '5000' ms', in the configured
    timeout
    period of '60' secs
    at weblogic.socket.SocketMuxer$TimeoutTrigger.trigger(SocketMuxer.java:734)
    at weblogic.time.common.internal.ScheduledTrigger.run(ScheduledTrigger.java:243)
    at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:317)
    at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:97)
    at weblogic.time.common.internal.ScheduledTrigger.executeLocally(ScheduledTrigger.java:229)
    at weblogic.time.common.internal.ScheduledTrigger.execute(ScheduledTrigger.java:223)
    at weblogic.time.server.ScheduledTrigger.execute(ScheduledTrigger.java:49)
    at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:178)
    at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:151)
    Does weblogic 8.1 support JPDA? Any suggesstion is higly appreciated.
    Thanks.
    Arsel

Maybe you are looking for